Page 1 of 4 F10067 Series RTI AUDIO FILM CAPACITORS F10067 Series - 200VDC Metallized Polypropylene MATERIAL: Metallized Polypropylene capacitors in non-inductive construction. LEADS: Tinned Copper soldered to capacitor with 63-37 Sn-Pb TEMPERATURE RANGE: May be operated at rated voltage from -55°C to + 85°C. Voltage must be derated linearly to 60% between +85°C to +105°C. ELECTRICAL [NON-DESTRUCTIVE] TESTS: 1. Capacitance shall be measured at 1 KHz. ± 20 Hz and + 25°C for values up to 1.0 MFD. Values greater than 1.0 MFD. shall be measured at 120 Hz. ± 10 Hz. Ref: MIL-STD-202E, method 305. 2. Dissipation Factor shall be measured as described for capacitance and shall not exceed 0.2%. 3. Insulation Resistance shall be measured at rated voltage. After 2 minutes under voltage, minimum values shall be 200,000 MEG/MFD., need not exceed 400,000 megohms. Ref: MIL-STD-202E, method 302. 4. Dielectric Strength: Capacitors shall withstand specified DC test potential for 60 seconds through a limiting resistance of 1 ohm/volt. Terminal to terminal will be 150% of rated voltage. TerminaI to case will be 200 % of rated voltage.. Ref: MIL-STD-202E, method 301. 5. Dielectric Absorption shall not exceed 0.1% when tested to MIL-C-19978D. Ref: MIL-C-19978D, paragraph 3.22. TYPICAL TEMPERATURE CHARACTERISTICS RHOPOINT COMPONENTS LTD Tel: +44 (0) 870 608 1188 Fax: +44 (0) 870 241 2255 F10067 Series P/N F10067-102 F10067-122 F10067-152 F10067-182 F10067-222 F10067-272 F10067-332 F10067-392 F10067-472 F10067-562 F10067-682 F10067-822 F10067-103 F10067-123 F10067-153 F10067-183 F10067-223 F10067-273 F10067-333 F10067-393 F10067-473 F10067-563 F10067-683 F10067-823 Page 2 of 4 CAPACITANCE .001 MFD .0012 MFD .0015 MFD .0018 MFD .0022 MFD .0027 MFD .0033 MFD .0039 MFD .0047 MFD .0056 MFD .0068 MFD .0082 MFD .010 MFD .012 MFD .015 MFD .018 MFD .022 MFD .027 MFD .033 MFD .039 MFD .047 MFD .056 MFD .068 MFD .082 MFD Dia (in.) 0.32 0.32 0.32 0.32 0.32 0.32 0.32 0.32 0.32 0.32 0.32 0.32 0.32 0.34 0.36 0.40 0.40 0.42 0.46 0.48 0.48 0.48 0.52 0.50 Length (in.) 0.48 0.48 0.48 0.48 0.48 0.48 0.48 0.48 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.73 0.73 0.73 0.73 Lead (awg) #24 #24 #24 #24 #24 #24 #24 #24 #24 #24 #24 #24 #24 #24 #24 #24 #24 #24 #24 #24 #22 #22 #22 #22 LeadDia 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.025 0.025 0.025 0.025 Last character on Part No. indicates tolerance: K- ±10%, J - ±5%, G - ±2%, F - ±1% Custom values obtainable, notify factory for suggestions. RHOPOINT COMPONENTS LTD Tel: +44 (0) 870 608 1188 Fax: +44 (0) 870 241 2255 F10067 Series P/N F10067-104 F10067-124 F10067-154 F10067-184 F10067-224 F10067-274 F10067-334 F10067-394 F10067-474 F10067-564 F10067-684 F10067-824 F10067-105 F10067-125 F10067-155 F10067-185 F10067-205 F10067-225 F10067-255 F10067-275 F10067-305 F10067-335 F10067-357 F10067-375 Page 3 of 4 CAPACITANCE .10 MFD .12 MFD .15 MFD .18 MFD .22 MFD .27 MFD .33 MFD .39 MFD .47 MFD .56 MFD .68 MFD .82 MFD 1.0 MFD 1.2 MFD 1.5 MFD 1.8 MFD 2.0 MFD 2.2 MFD 2.5 MFD 2.7 MFD 3.0 MFD 3.3 MFD 3.5 MFD 3.7 MFD Dia (in.) 0.40 0.42 0.45 0.48 0.38 0.40 0.44 0.46 0.52 0.54 0.60 0.64 0.70 0.68 0.75 0.80 0.85 0.90 0.88 0.90 0.94 1.00 1.02 0.96 Length (in.) 0.73 0.73 0.73 0.73 0.84 0.84 0.84 0.84 0.84 0.84 0.84 0.84 0.84 0.98 0.98 0.98 0.98 0.98 1.10 1.10 1.10 1.10 1.10 1.28 Lead (awg) #22 #22 #22 #22 #22 #22 #22 #22 #22 #22 #22 #22 #22 #20 #20 #20 #20 #20 #20 #20 #20 #20 #20 #20 Lead Dia 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 Last character on Part No. indicates tolerance: K- ±10%, J - ±5%, G - ±2%, F - ±1% Custom values obtainable, notify factory for suggestions. RHOPOINT COMPONENTS LTD Tel: +44 (0) 870 608 1188 Fax: +44 (0) 870 241 2255 F10067 Series Page 4 of 4 P/N F10067-405 F10067-475 F10067-505 F10067-565 F10067-605 F10067-655 F10067-705 F10067-755 F10067-805 F10067-855 F10067-905 F10067-955 F10067-106 F10067-116 F10067-126 F10067-136 F10067-146 F10067-156 F10067-166 F10067-186 F10067-206 F10067-256 F10067-306 F10067-356 CAPACITANCE 4.0 MFD 4.7 MFD 5.0 MFD 5.6 MFD 6.0 MFD 6.5 MFD 7.0 MFD 7.5 MFD 8.0 MFD 8.5 MFD 9.0 MFD 9.5 MFD 10.0 MFD 11.0 MFD 12.0 MFD 13.0 MFD 14.0 MFD 15.0 MFD 16.0 MFD 18.0 MFD 20.0 MFD 25.0 MFD 30.0 MFD 35.0 MFD Dia (in.) 1.00 1.10 1.12 1.04 1.08 1.10 1.15 1.20 1.25 1.28 1.25 1.28 1.30 1.36 1.42 1.46 1.50 1.50 1.54 1.64 1.72 1.82 1.92 2.06 Length (in.) 1.30 1.30 1.30 1.55 1.55 1.55 1.55 1.55 1.55 1.55 1.68 1.68 1.68 1.68 1.68 1.68 1.68 1.80 1.80 1.80 1.80 1.92 2.06 2.06 Lead (awg) #20 #20 #20 #20 #20 #20 #20 #20 #20 #20 #20 #20 #18 #18 #18 #18 #18 #18 #18 #18 #18 #18 #18 #18 Lead Dia 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.040 0.040 0.040 0.040 0.040 0.040 0.040 0.040 0.040 0.040 0.040 0.040 Last character on Part No. indicates tolerance: K- ±10%, J - ±5%, G - ±2%, F - ±1% Custom values obtainable, notify factory for suggestions. Rhopoint Components Ltd Tel: +44 (0) 870 608 1188 Fax: +44 (0) 870 241 2255 Germany +49 (0) 692 199 8606 Fax: +49 (0) 692 199 8595 Email: [email protected] Website: www.rhopointcomponents.com RHOPOINT COMPONENTS LTD Tel: +44 (0) 870 608 1188 Fax: +44 (0) 870 241 2255