METALLIZED POLYPHENYLENE SULFIDE FILM CAPACITORS HERMETICALLY SEALED - ROUND TUBULAR METALLIZED POLYPHENYLENE SULFIDE Self-healing, high reliability High stability Low capacitance change over wide temperature range High volumetric efficiency Precision circuits requiring low losses, light duty, low frequency energy discharge, coupling and decoupling STYLE “L1” Round hermetically sealed tube Ultimate in moisture resistance Compression type glass end seal possess extraordinary immunity to vibration, pressure and temperature changes Encasement – tubular brass, electro-tinned Metallized Polyphenylene Sulfide capacitors in hermetically sealed cases are available in many styles. Please contact factory or representative. SPECIFICATIONS CONSTRUCTION: metallized Polyphenylene sulfide capacitors are available only in extended foil (non-inductive) construction PACKAGING: round hermetically sealed tubular style, non-magnetic metal tube, with compression glass end seal, axial copperweld leads LEADS: tin or tin/lead plated copper wire is standard and may be soldered or welded in circuit assembly TEMPERATURE RANGE: may be operated at rated DC voltage from -55°C to 125°C without derating voltage ELECTRICAL (NON-DESTRUCTIVE) TEST 1. 2. 3. 4. 5. CAPACITANCE: shall be measured at or referred to 1000 ± 20 Hz at 25 ± 5°C for capacitance values up to and including 1.0 uf. Capacitance values greater than 1.0 mfd shall be measured at 60 ± 6 Hz. Ref: MIL-STD-202E, Method 305 DISSIPATION FACTOR: shall be measured as described for capacitance and shall not exceed 0.3% to 1 mfd, 0.5% greater than 1 mfd. Typical values throughout the temperature range, are given on curves. INSULATION RESISTANCE: shall be measured as follows: 50-100V at 25°C 25,000 meg/mfd, need not exceed 50,000 Megohms 200V + at 25°C 50,000 meg/mfd, need not exceed 100,000 Megohms Ref: MIL-STD-202E, Method 302 DIELECTRIC STRENGTH: capacitors shall withstand specified DC test potential for one minute through a limiting resistance of 1 ohm/volt Terminal to terminal -- 150% of DC rating Terminal to case -- 200% of DC rating Ref: MIL-STD-202E, Method 301 DIELECTRIC ABSORPTION: shall not exceed 0.2% when tested to MIL-C-19978D Ref: MIL-C-19978D Electromagnetic Integrated Solutions 8061 Avonia Road ● Fairview ● Pennsylvania ● 16415 Phone: (814) 474-1571 ● Email: [email protected] ● Web: http://eis.apitech.com ENVIRONMENTAL TESTS 1. 2. 3. 4. VIBRATION: capacitors will meet or exceed the requirements of MIL-STD-202E, Method 204 MOISTURE RESISTANCE: capacitors will meet or exceed the requirements of MIL-STD-202E. Method 103B, condition B, with 500 VDC or rated voltage applied, whichever is less. LIFE TEST: will withstand 140% of the rated DC voltage at 125°C for 250 hours with not more than one failure in 12 units LEAD PULL TEST: the leads on these capacitors shall withstand a steadily applied axial pull of 5 lbs. for one minute CUSTOM DESIGN Available on short notice -- special shapes, values, characteristics, combination sections and networks. Non-metallic cases or fabricated steel and brass with glass-to-metal seals. Engineering service is expert and prompt. APPLICATIONS Metallized Polyphenylene Sulfide capacitors in Style "L" hermetically sealed tubular cases offer the user the ultimate in insulation resistance. These capacitors will meet the environmental requirements of MIL-C-39022C and moisture resistance per MIL-STD-202E, Method 106D. Metallized Polyphenylene Sulfide capacitors combine the reliability of self-healing action with high dielectric strength and insulation resistance of polycarbonate film. Metallized Polyphenylene Sulfide capacitors are designed primarily for DC application -- blocking, coupling, decoupling, bypass DC line filtering - where RF and audio components are small in comparison to DC rating. However, they have been successfully used in AC power applications such as power factor correction and AC line filtering. Metallized Polyphenylene Sulfide capacitors operate at all temperatures from -55°C to + 125°C. APPLICATION GUIDE: [AC VOLTAGE RATING, -55˚C to +125˚C. AMBIENT] EQUIVALENT VAC [RMS] RATING AT VOLTAGE RATING 60 Hz 400 Hz 50V N/A N/A 100V 63 VAC 45 VAC 200V 160 VAC 95 VAC 400V 200 VAC 170 VAC 600V 240 VAC 190 VAC (AC voltage assumed to be pure sine wave) TYPICAL TEMPERATURE CHARACTERISTICS Electromagnetic Integrated Solutions 8061 Avonia Road ● Fairview ● Pennsylvania ● 16415 Phone: (814) 474-1571 ● Email: [email protected] ● Web: http://eis.apitech.com 1000 Hz N/A 40 VAC 80 VAC 140 VAC 160 VAC WL1, NL1, AL1 SERIES – SPECIFICATIONS DIMENSIONS *50 VDC MFD .0010 .0012 .0015 .0018 .0022 .0027 .0033 .0039 .0047 .0056 .0068 .0082 .010 .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .10 .12 .15 .18 .22 .27 .33 .39 .47 .56 .68 .82 1.0 1.5 2.0 3.0 4.0 5.0 Dia. .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .155 .195 .195 .195 .195 .195 .195 .195 .195 .235 .235 .235 .235 .235 .312 .312 .312 .312 .400 .400 .400 .400 .400 .500 .500 .500 L 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 13/16 15/16 15/16 15/16 1-1/8 1-5/16 Part No. WL1A102 WL1A122 WL1A152 WL1A182 WL1A222 WL1A272 WL1A332 WL1A392 WL1A472 WL1A562 WL1A682 WL1A822 WL1A103 WL1A123 WL1A153 WL1A183 WL1A223 WL1A273 WL1A333 WL1A393 WL1A473 WL1A563 WL1A683 WL1A823 WL1A104 WL1A124 WL1A154 WL1A184 WL1A224 WL1A274 WL1A334 WL1A394 WL1A474 WL1A564 WL1A684 WL1A824 WL1A105 WL1A155 WL1A205 WL1A305 WL1A405 WL1A505 **50 – 100 VDC Dia. .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .235 .235 .235 .235 .235 .312 .312 .312 .312 .312 .312 .312 .312 .400 .400 .400 .400 .500 .562 .562 .670 .670 L 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 13/16 13/16 13/16 13/16 13/16 13/16 13/16 15/16 15/16 1-1/8 1-1/8 1-1/8 1-1/8 1-5/16 1-5/16 1-5/16 1-5/16 1-13/16 1-9/16 1-3/16 Part No. NL1B102 NL1B122 NL1B152 NL1B182 NL1B222 NL1B272 NL1B332 NL1B392 NL1B472 NL1B562 NL1B682 NL1B822 NL1B103 NL1B123 NL1B153 NL1B183 NL1B223 NL1B273 NL1B333 NL1B393 NL1B473 NL1B563 NL1B683 NL1B823 NL1B104 NL1B124 NL1B154 NL1B184 NL1B224 NL1B274 NL1B334 NL1B394 NL1B474 NL1B564 NL1B684 NL1B824 NL1B105 NL1B155 NL1B205 NL1B305 NL1B405 NL1B505 **50 – 200 VDC Dia. .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .235 .235 .235 .312 .312 .312 .312 .312 .312 .312 .312 .400 .400 .400 .500 .500 .500 .500 .500 .500 .562 .562 .670 670 .750 1.00 L 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 13/16 13/16 13/16 13/16 13/16 15/16 15/16 15/16 1-1/8 15/16 1-1/8 1-1/8 1-5/16 1-5/16 1-5/16 1-5/16 1-9/16 1-9/16 1-13/16 1-13/16 1-9/16 Part No. AL1C102 AL1C122 AL1C152 AL1C182 AL1C222 AL1C272 AL1C332 AL1C392 AL1C472 AL1C562 AL1C682 AL1C822 AL1C103 AL1C123 AL1C153 AL1C183 AL1C223 AL1C273 AL1C333 AL1C393 AL1C473 AL1C563 AL1C683 AL1C823 AL1C104 AL1C124 AL1C154 AL1C184 AL1C224 AL1C274 AL1C334 AL1C394 AL1C474 AL1C564 AL1C684 AL1C824 AL1C105 AL1C155 AL1C205 AL1C305 AL1C405 AL1C505 400 VDC Dia. .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .235 .235 .235 .235 .235 .235 .235 .312 .312 .312 .312 .312 .312 .400 .400 .400 .500 .500 .562 .562 .562 .670 .670 .670 .750 .750 .750 1.00 1.00 L 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 13/16 13/16 13/16 13/16 13/16 13/16 15/16 15/16 1-1/8 15/16 1-1/8 1-5/16 1-5/16 1-5/16 1-5/16 1-9/16 1-9/16 1-9/16 1-9/16 1-13/16 1-13/16 1-13/16 2-1/16 1-13/16 2-1/16 Higher values or voltages are available. *50 VDC units also available in A and N material. **100 VDC units also available in A material. CASE DIA. .195 .235 THRU .312 .400 THRU 1.0 STYLE W ONLY WIRE LEADS A.W.G. #24 #22 #20 #22 Electromagnetic Integrated Solutions 8061 Avonia Road ● Fairview ● Pennsylvania ● 16415 Phone: (814) 474-1571 ● Email: [email protected] ● Web: http://eis.apitech.com LEADS DIA. .020 .025 .032 .025 600 VDC Part No. AL1E102 AL1E122 AL1E152 AL1E182 AL1E222 AL1E272 AL1E332 AL1E392 AL1E472 AL1E562 AL1E682 AL1E822 AL1E103 AL1E123 AL1E153 AL1E183 AL1E223 AL1E273 AL1E333 AL1E393 AL1E473 AL1E563 AL1E683 AL1E823 AL1E104 AL1E124 AL1E154 AL1E184 AL1E224 AL1E274 AL1E334 AL1E394 AL1E474 AL1E564 AL1E684 AL1E824 AL1E105 AL1E155 AL1E205 Dia. .195 .195 .195 .195 .195 .195 .195 .235 .235 .235 .235 .235 .312 .312 .312 .312 .312 .312 .400 .400 .400 .400 .400 .500 .500 .500 .500 .562 .562 .670 .670 .670 .670 .750 .750 1.00 1.00 1.00 L 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 13/16 13/16 13/16 13/16 13/16 13/16 13/16 15/16 1-1/8 15/16 15/16 1-1/8 1-1/8 1-5/16 1-1/8 1-1/8 1-5/16 1-5/16 1-5/16 1-9/16 1-9/16 1-9/16 1-13/16 1-13/16 2-1/16 2-1/16 1-13/16 1-13/16 2-5/16 Part No. AL1G102 AL1G122 AL1G152 AL1G182 AL1G222 AL1G272 AL1G332 AL1G392 AL1G472 AL1G562 AL1G682 AL1G822 AL1G103 AL1G123 AL1G153 AL1G183 AL1G223 AL1G273 AL1G333 AL1G393 AL1G473 AL1G563 AL1G683 AL1G823 AL1G104 AL1G124 AL1G154 AL1G184 AL1G224 AL1G274 AL1G334 AL1G394 AL1G474 AL1G564 AL1G684 AL1G824 AL1G105 AL1G155