F10068 Series

 Film Capacitor
F10068 Series – 400 VDC
Metallized Polypropylene
MATERIAL: metallized polypropylene capacitors in non-inductive
construction
LEADS: tinned copper soldered to capacitor with 63-37 Sn-Pb
TEMPERATURE RANGE: may be operated at rated voltage from -55°C to +85°C. Voltage must
be de-rated linearly to 60% between +85°C to +105°C.
ELECTRICAL [NON-DESTRUCTIVE] TESTS
1. CAPACITANCE: shall be measured at 1 KHz ± 20 Hz and +25°C for values up to 1.0
mfd. Values greater than 1.0 mfd shall be measured at 120 Hz ± 10 Hz.
Ref: MIL-STD-202E, method 305
2. DISSIPATION FACTOR: shall be measured as described for capacitance and shall not
exceed 0.2%
3. INSULATION RESISTANCE: shall be measured at rated voltage. After two minutes
under voltage, minimum values shall be 200,000 meg/mfd, need not exceed 400,000
Megohms.
Ref: MIL-STD-202E, method 302
4. DIELECTRIC STRENGTH: capacitors shall withstand specified DC test potential for 60
seconds through a limiting resistance of 1 ohm/volt
Terminal to terminal will be 150% of rated voltage
Terminal to case will be 200% of rated voltage
Ref: MIL-STD-202E, method 301
5. DIELECTRIC ABSORPTION: shall not exceed 0.1% when tested to MIL-C-19978D
Ref: MIL-C-19978D, paragraph 3.22
TYPICAL TEMPERATURE CHARACTERISTICS
Electromagnetic Integrated Solutions
8061 Avonia Road ● Fairview ● Pennsylvania ● 16415
Phone: (814) 474-1571 ● Email: [email protected] ● Web: http://eis.apitech.com
DIMENSIONS
P/N
Capacitance
Dia (in.)
Length (in.)
Lead (awg)
Lead Dia
F10068-682
F10068-822
F10068-103
F10068-223
F10068-333
F10068-473
F10068-683
F10068-823
F10068-104
F10068-224
F10068-334
F10068-474
F10068-684
F10068-824
F10068-105
F10068-205
F10068-225
F10068-255
F10068-305
F10068-335
F10068-475
F10068-505
F10068-805
F10068-106
.0068 MFD
.0082 MFD
.010 MFD
.022 MFD
.033 MFD
.047 MFD
.068 MFD
.082 MFD
.10 MFD
.22 MFD
.33 MFD
.47 MFD
.68 MFD
.82 MFD
1.0 MFD
2.0 MFD
2.2 MFD
2.5 MFD
3.0 MFD
3.3 MFD
4.7 MFD
5.0 MFD
8.0 MFD
10.0 MFD
0.32
0.32
0.32
0.38
0.38
0.40
0.45
0.48
0.53
0.65
0.70
0.82
0.83
0.92
1.00
0.94
0.98
1.04
1.13
1.06
1.24
1.22
1.54
1.70
0.60
0.60
0.60
0.60
0.72
0.72
0.72
0.72
0.72
0.85
0.98
0.98
1.28
1.28
1.28
1.28
1.28
1.28
1.28
1.53
1.53
1.70
1.70
1.70
#24
#24
#24
#24
#22
#22
#22
#22
#22
#22
#20
#20
#20
#20
#20
#20
#20
#20
#18
#18
#18
#18
#18
#18
0.020
0.020
0.020
0.020
0.025
0.025
0.025
0.025
0.025
0.025
0.031
0.031
0.031
0.031
0.031
0.031
0.031
0.031
0.040
0.040
0.040
0.040
0.040
0.040
Last character on Part No. indicates tolerance: K - ±10%, J - ±5%, G - ±2%, F - ±1%
Custom values obtainable, notify factory for suggestions.
Electromagnetic Integrated Solutions
8061 Avonia Road ● Fairview ● Pennsylvania ● 16415
Phone: (814) 474-1571 ● Email: [email protected] ● Web: http://eis.apitech.com