PSoC® Mixed-Signal Array Final Data Sheet Automotive: CY8C24223A and CY8C24423A Features ■ Powerful Harvard Architecture Processor ❐ M8C Processor Speeds to 12 MHz ❐ 8x8 Multiply, 32-Bit Accumulate ❐ Low Power at High Speed ❐ 4.75V to 5.25V Operating Voltage ❐ Extended Temp. Range: -40°C to +125°C ■ Precision, Programmable Clocking ❐ Internal ±4% 24 MHz Oscillator ❐ High-Accuracy 24 MHz with Optional 32 kHz Crystal and PLL ❐ Optional External Oscillator, up to 24 MHz ❐ Internal Oscillator for Watchdog and Sleep ■ Advanced Peripherals (PSoC Blocks) ❐ 6 Rail-to-Rail Analog PSoC Blocks Provide: - Up to 14-Bit ADCs - Up to 9-Bit DACs - Programmable Gain Amplifiers - Programmable Filters and Comparators ❐ 4 Digital PSoC Blocks Provide: - 8- to 32-Bit Timers, Counters, and PWMs - CRC and PRS Modules - Full-Duplex UART - Multiple SPI™ Masters or Slaves - Connectable to all GPIO Pins ❐ Complex Peripherals by Combining Blocks ■ Flexible On-Chip Memory ❐ 4K Bytes Flash Program Storage 100 Erase/ Write Cycles ❐ 256 Bytes SRAM Data Storage ❐ In-System Serial Programming (ISSP) ❐ Partial Flash Updates ❐ Flexible Protection Modes Port 2 ■ Programmable Pin Configurations ❐ 25 mA Sink on All GPIO ❐ Pull Up, Pull Down, High Z, Strong, or Open Drain Drive Modes on All GPIO ❐ Up to 10 Analog Inputs on GPIO ❐ Two 30 mA Analog Outputs on GPIO ❐ Configurable Interrupt on All GPIO Port 1 Port 0 Analog Drivers PSoC CORE System Bus Global Digital Interconnect SRAM 256 Bytes SROM Global Analog Interconnect Flash 4K CPUCore (M8C) Interrupt Controller Sleep and Watchdog Multiple Clock Sources (Includes IMO, ILO, PLL, and ECO) DIGITAL SYSTEM ANALOG SYSTEM Digital Block Array Analog Block Array (1 Row, 4 Blocks) (2 Columns, 6 Blocks) Analog Ref Analog Input Muxing ■ Additional System Resources ❐ I2C™ Slave, Master, and Multi-Master to 400 kHz ❐ Watchdog and Sleep Timers ❐ User-Configurable Low Voltage Detection ❐ Integrated Supervisory Circuit ❐ On-Chip Precision Voltage Reference ■ Complete Development Tools ❐ Free Development Software (PSoC Designer™) ❐ Full-Featured, In-Circuit Emulator and Programmer ❐ Full Speed Emulation ❐ Complex Breakpoint Structure ❐ 128K Bytes Trace Memory PSoC® Functional Overview The PSoC® family consists of many Mixed-Signal Array with On-Chip Controller devices. These devices are designed to replace multiple traditional MCU-based system components with one, low cost single-chip programmable device. PSoC devices include configurable blocks of analog and digital logic, as well as programmable interconnects. This architecture allows the user to create customized peripheral configurations that match the requirements of each individual application. Additionally, a fast CPU, Flash program memory, SRAM data memory, and configurable IO are included in a range of convenient pinouts and packages. The PSoC architecture, as illustrated on the left, is comprised of four main areas: PSoC Core, Digital System, Analog System, and System Resources. Configurable global busing allows all the device resources to be combined into a complete custom system. The PSoC automotive CY8C24x23A group can have up to three IO ports that connect to the global digital and analog interconnects, providing access to 4 digital blocks and 6 analog blocks. The PSoC Core Digital Clocks Multiply Accum. POR and LVD Decimator I2C System Resets Internal Voltage Ref. The PSoC Core is a powerful engine that supports a rich feature set. The core includes a CPU, memory, clocks, and configurable GPIO (General Purpose IO). SYSTEM RESOURCES October 9, 2006 © Cypress Semiconductor Corp. 2004-2006 — Document No. 38-12029 Rev. *C 1 [+] Feedback CY8C24x23A Automotive Data Sheet PSoC® Overview The M8C CPU core is a powerful processor with speeds up to 12 MHz, providing a two MIPS 8-bit Harvard architecture microprocessor. The CPU utilizes an interrupt controller with 11 vectors, to simplify programming of real time embedded events. Program execution is timed and protected using the included Sleep and Watch Dog Timers (WDT). Digital peripheral configurations include those listed below. ■ PWMs (8 to 32 bit) ■ PWMs with Dead Band (8 to 32 bit) ■ Counters (8 to 32 bit) ■ Timers (8 to 32 bit) Memory includes 4 KB of Flash for program storage and 256 bytes of SRAM for data storage. Program Flash utilizes four protection levels on blocks of 64 bytes, allowing customized software IP protection. ■ UART 8 bit with selectable parity ■ SPI Master and Slave ■ I2C Slave and Multi-Master (1 available as a System Resource) The PSoC device incorporates flexible internal clock generators, including a 24 MHz IMO (internal main oscillator) accurate to 4% over temperature and voltage. A low power 32 kHz ILO (internal low speed oscillator) is provided for the Sleep timer and WDT. If crystal accuracy is desired, the ECO (32.768 kHz external crystal oscillator) is available for use as a Real Time Clock (RTC) and can optionally generate a crystal-accurate 24 MHz system clock using a PLL. The clocks, together with programmable clock dividers (as a System Resource), provide the flexibility to integrate almost any timing requirement into the PSoC device. ■ Cyclical Redundancy Checker/Generator (8 to 32 bit) ■ IrDA ■ Pseudo Random Sequence Generators (8 to 32 bit) PSoC GPIOs provide connection to the CPU, digital and analog resources of the device. Each pin’s drive mode may be selected from eight options, allowing great flexibility in external interfacing. Every pin also has the capability to generate a system interrupt on high level, low level, and change from last read. The Digital System The Digital System is composed of 4 digital PSoC blocks. Each block is an 8-bit resource that can be used alone or combined with other blocks to form 8, 16, 24, and 32-bit peripherals, which are called user module references. The digital blocks can be connected to any GPIO through a series of global buses that can route any signal to any pin. The buses also allow for signal multiplexing and for performing logic operations. This configurability frees your designs from the constraints of a fixed peripheral controller. Digital blocks are provided in rows of four, where the number of blocks varies by PSoC device family. This allows you the optimum choice of system resources for your application. Family resources are shown in the table titled “PSoC Device Characteristics” on page 3. The Analog System The Analog System is composed of 6 configurable blocks, each comprised of an opamp circuit allowing the creation of complex analog signal flows. Analog peripherals are very flexible and can be customized to support specific application requirements. Some of the more common PSoC analog functions (most available as user modules) are listed below. ■ Analog-to-digital converters (up to 2, with 6- to 14-bit resolution, selectable as Incremental, Delta Sigma, and SAR) ■ Filters (2 and 4 pole band-pass, low-pass, and notch) ■ Amplifiers (up to 2, with selectable gain to 48x) ■ Instrumentation amplifiers (1 with selectable gain to 93x) ■ Comparators (up to 2, with 16 selectable thresholds) DIGITAL SYSTEM ■ DACs (up to 2, with 6- to 9-bit resolution) Digital PSoC Block Array ■ Multiplying DACs (up to 2, with 6- to 9-bit resolution) ■ High current output drivers (two with 30 mA drive as a PSoC Core resource) ■ 1.3V reference (as a System Resource) ■ DTMF Dialer Port 1 Port 2 Port 0 To System Bus 8 Row 0 DBB00 DBB01 DCB02 To Analog System 4 Row Output Configuration 8 Row Input Configuration Digital Clocks From Core DCB03 4 GIE[7:0] GIO[7:0] Global Digital Interconnect 8 8 ■ Modulators GOE[7:0] ■ Correlators GOO[7:0] ■ Peak Detectors ■ Many other topologies possible Digital System Block Diagram October 9, 2006 Document No. 38-12029 Rev. *C 2 [+] Feedback CY8C24x23A Automotive Data Sheet PSoC® Overview Analog blocks are arranged in a column of three, which includes one CT (Continuous Time) and two SC (Switched Capacitor) blocks, as shown in the figure below. P0[6] P0[5] P0[4] P0[3] P0[2] P0[1] P0[0] AGNDIn RefIn P0[7] P2[3] P2[1] P2[6] Additional System Resources System Resources, some of which have been previously listed, provide additional capability useful to complete systems. Additional resources include a multiplier, decimator, switch mode pump, low voltage detection, and power on reset. Brief statements describing the merits of each system resource are presented below. ■ Digital clock dividers provide three customizable clock frequencies for use in applications. The clocks can be routed to both the digital and analog systems. Additional clocks can be generated using digital PSoC blocks as clock dividers. ■ A multiply accumulate (MAC) provides a fast 8-bit multiplier with 32-bit accumulate, to assist in both general math as well as digital filters. ■ The decimator provides a custom hardware filter for digital signal processing applications including the creation of Delta Sigma ADCs. ■ The I2C module provides 100 and 400 kHz communication over two wires. Slave, master, and multi-master modes are all supported. ■ Low Voltage Detection (LVD) interrupts can signal the application of falling voltage levels, while the advanced POR (Power On Reset) circuit eliminates the need for a system supervisor. ■ An internal 1.3V reference provides an absolute reference for the analog system, including ADCs and DACs. P2[4] P2[2] P2[0] Array Input Configuration ACI0[1:0] ACI1[1:0] PSoC Device Characteristics Block Array ACB00 ACB01 ASC10 ASD11 ASD20 ASC21 Depending on your PSoC device characteristics, the digital and analog systems can have 16, 8, or 4 digital blocks and 12, 6, or 4 analog blocks. The following table lists the resources available for specific PSoC device groups. The PSoC device covered by this data sheet is highlighted below. PSoC Device Characteristics Analog Columns Analog Blocks SRAM Size Flash Size Analog System Block Diagram Analog Outputs M8C Interface (Address Bus, Data Bus, Etc.) AGNDIn RefIn Bandgap Analog Inputs Reference Generators Digital Blocks RefHi RefLo AGND Digital Rows Interface to Digital System Digital IO Analog Reference CY8C29x66 up to 64 4 16 12 4 4 12 2K 32K CY8C27x43 up to 44 2 8 12 4 4 12 256 Bytes 16K CY8C24x94 49 1 4 48 2 2 6 1K 16K CY8C24x23 up to 24 1 4 12 2 2 6 256 Bytes 4K CY8C24x23A up to 24 1 4 12 2 2 6 256 Bytes 4K CY8C21x34 up to 28 1 4 28 0 2 4a 512 Bytes 8K CY8C21x23 16 1 4 8 0 2 4a 256 Bytes 4K PSoC Part Number a. Limited analog functionality. October 9, 2006 Document No. 38-12029 Rev. *C 3 [+] Feedback CY8C24x23A Automotive Data Sheet PSoC® Overview Getting Started Development Tools The quickest path to understanding the PSoC silicon is by reading this data sheet and using the PSoC Designer Integrated Development Environment (IDE). This data sheet is an overview of the PSoC integrated circuit and presents specific pin, register, and electrical specifications. For in-depth information, along with detailed programming information, reference the PSoC™ Mixed-Signal Array Technical Reference Manual. PSoC Designer is a Microsoft® Windows-based, integrated development environment for the Programmable System-onChip (PSoC) devices. The PSoC Designer IDE and application runs on Windows NT 4.0, Windows 2000, Windows Millennium (Me), or Windows XP. (Reference the PSoC Designer Functional Flow diagram below.) Development Kits Development Kits are available from the following distributors: Digi-Key, Avnet, Arrow, and Future. The Cypress Online Store at http://www.onfulfillment.com/cypressstore/ contains development kits, C compilers, and all accessories for PSoC development. Click on PSoC (Programmable System-on-Chip) to view a current list of available items. Tele-Training PSoC Designer also supports a high-level C language compiler developed specifically for the devices in the family. Importable Design Database Device Database Consultants Certified PSoC Consultants offer everything from technical assistance to completed PSoC designs. To contact or become a PSoC Consultant, go to the following Cypress support web site: http://www.cypress.com/support/cypros.cfm. Technical Support PSoC application engineers take pride in fast and accurate response. They can be reached with a 4-hour guaranteed response at http://www.cypress.com/support/login.cfm. Context Sensitive Help Graphical Designer Interface PSoC Designer Results Free PSoC "Tele-training" is available for beginners and taught by a marketing or application engineer over the phone. Five training classes are available to accelerate the learning curve including introduction, designing, debugging, advanced design, advanced analog, as well as application-specific classes covering topics like PSoC and the LIN bus. For days and times of the tele-training, see http://www.cypress.com/support/training.cfm. PSoC Designer helps the customer to select an operating configuration for the PSoC, write application code that uses the PSoC, and debug the application. This system provides design database management by project, an integrated debugger with In-Circuit Emulator, in-system programming support, and the CYASM macro assembler for the CPUs. Commands For up-to-date Ordering, Packaging, and Electrical Specification information, reference the latest PSoC device data sheets on the web at http://www.cypress.com/psoc. PSoC Designer Core Engine Application Database Project Database PSoC Configuration Sheet Manufacturing Information File User Modules Library Application Notes A long list of application notes will assist you in every aspect of your design effort. To view the PSoC application notes, go to the http://www.cypress.com web site and select Application Notes under the Design Resources list located in the center of the web page. Application notes are sorted by date by default. October 9, 2006 Emulation Pod Document No. 38-12029 Rev. *C In-Circuit Emulator Device Programmer PSoC Designer Subsystems 4 [+] Feedback CY8C24x23A Automotive Data Sheet PSoC® Overview PSoC Designer Software Subsystems Device Editor The Device Editor subsystem allows the user to select different onboard analog and digital components called user modules using the PSoC blocks. Examples of user modules are ADCs, DACs, Amplifiers, and Filters. The device editor also supports easy development of multiple configurations and dynamic reconfiguration. Dynamic configuration allows for changing configurations at run time. PSoC Designer sets up power-on initialization tables for selected PSoC block configurations and creates source code for an application framework. The framework contains software to operate the selected components and, if the project uses more than one operating configuration, contains routines to switch between different sets of PSoC block configurations at run time. PSoC Designer can print out a configuration sheet for a given project configuration for use during application programming in conjunction with the Device Data Sheet. Once the framework is generated, the user can add application-specific code to flesh out the framework. It’s also possible to change the selected components and regenerate the framework. Design Browser The Design Browser allows users to select and import preconfigured designs into the user’s project. Users can easily browse a catalog of preconfigured designs to facilitate time-to-design. Examples provided in the tools include a 300-baud modem, LIN Bus master and slave, fan controller, and magnetic card reader. Application Editor Debugger The PSoC Designer Debugger subsystem provides hardware in-circuit emulation, allowing the designer to test the program in a physical system while providing an internal view of the PSoC device. Debugger commands allow the designer to read and program and read and write data memory, read and write IO registers, read and write CPU registers, set and clear breakpoints, and provide program run, halt, and step control. The debugger also allows the designer to create a trace buffer of registers and memory locations of interest. Online Help System The online help system displays online, context-sensitive help for the user. Designed for procedural and quick reference, each functional subsystem has its own context-sensitive help. This system also provides tutorials and links to FAQs and an Online Support Forum to aid the designer in getting started. Hardware Tools In-Circuit Emulator A low cost, high functionality ICE (In-Circuit Emulator) is available for development support. This hardware has the capability to program single devices. The emulator consists of a base unit that connects to the PC by way of the parallel or USB port. The base unit is universal and will operate with all PSoC devices. Emulation pods for each device family are available separately. The emulation pod takes the place of the PSoC device in the target board and performs full speed (12 MHz) operation. In the Application Editor you can edit your C language and Assembly language source code. You can also assemble, compile, link, and build. Assembler. The macro assembler allows the assembly code to be merged seamlessly with C code. The link libraries automatically use absolute addressing or can be compiled in relative mode, and linked with other software modules to get absolute addressing. C Language Compiler. A C language compiler is available that supports Cypress MicroSystems’ PSoC family devices. Even if you have never worked in the C language before, the product quickly allows you to create complete C programs for the PSoC family devices. The embedded, optimizing C compiler provides all the features of C tailored to the PSoC architecture. It comes complete with embedded libraries providing port and bus operations, standard keypad and display support, and extended math functionality. October 9, 2006 Document No. 38-12029 Rev. *C 5 [+] Feedback CY8C24x23A Automotive Data Sheet PSoC® Overview Designing with User Modules The development process for the PSoC device differs from that of a traditional fixed function microprocessor. The configurable analog and digital hardware blocks give the PSoC architecture a unique flexibility that pays dividends in managing specification change during development and by lowering inventory costs. These configurable resources, called PSoC Blocks, have the ability to implement a wide variety of user-selectable functions. Each block has several registers that determine its function and connectivity to other blocks, multiplexers, buses and to the IO pins. Iterative development cycles permit you to adapt the hardware as well as the software. This substantially lowers the risk of having to select a different part to meet the final design requirements. Device Editor User Module Selection The API functions are documented in user module data sheets that are viewed directly in the PSoC Designer IDE. These data sheets explain the internal operation of the user module and provide performance specifications. Each data sheet describes the use of each user module parameter and documents the setting of each register controlled by the user module. The development process starts when you open a new project and bring up the Device Editor, a graphical user interface (GUI) for configuring the hardware. You pick the user modules you need for your project and map them onto the PSoC blocks with point-and-click simplicity. Next, you build signal chains by interconnecting user modules to each other and the IO pins. At this stage, you also configure the clock source connections and enter parameter values directly or by selecting values from drop-down menus. When you are ready to test the hardware configuration or move on to developing code for the project, you perform the “Generate Application” step. This causes PSoC Designer to generate source code that automatically configures the device to your specification and provides the high-level user module API functions. October 9, 2006 Source Code Generator Generate Application Application Editor To speed the development process, the PSoC Designer Integrated Development Environment (IDE) provides a library of pre-built, pre-tested hardware peripheral functions, called “User Modules.” User modules make selecting and implementing peripheral devices simple, and come in analog, digital, and mixed signal varieties. The standard User Module library contains over 50 common peripherals such as ADCs, DACs Timers, Counters, UARTs, and other not-so common peripherals such as DTMF Generators and Bi-Quad analog filter sections. Each user module establishes the basic register settings that implement the selected function. It also provides parameters that allow you to tailor its precise configuration to your particular application. For example, a Pulse Width Modulator User Module configures one or more digital PSoC blocks, one for each 8 bits of resolution. The user module parameters permit you to establish the pulse width and duty cycle. User modules also provide tested software to cut your development time. The user module application programming interface (API) provides highlevel functions to control and respond to hardware events at run-time. The API also provides optional interrupt service routines that you can adapt as needed. Placement and Parameter -ization Project Manager Source Code Editor Build Manager Build All Debugger Interface to ICE Storage Inspector Event & Breakpoint Manager User Module and Source Code Development Flows The next step is to write your main program, and any sub-routines using PSoC Designer’s Application Editor subsystem. The Application Editor includes a Project Manager that allows you to open the project source code files (including all generated code files) from a hierarchal view. The source code editor provides syntax coloring and advanced edit features for both C and assembly language. File search capabilities include simple string searches and recursive “grep-style” patterns. A single mouse click invokes the Build Manager. It employs a professional-strength “makefile” system to automatically analyze all file dependencies and run the compiler and assembler as necessary. Project-level options control optimization strategies used by the compiler and linker. Syntax errors are displayed in a console window. Double clicking the error message takes you directly to the offending line of source code. When all is correct, the linker builds a HEX file image suitable for programming. The last step in the development process takes place inside the PSoC Designer’s Debugger subsystem. The Debugger downloads the HEX image to the In-Circuit Emulator (ICE) where it runs at full speed. Debugger capabilities rival those of systems costing many times more. In addition to traditional single-step, run-to-breakpoint and watch-variable features, the Debugger provides a large trace buffer and allows you define complex breakpoint events that include monitoring address and data bus values, memory locations and external signals. Document No. 38-12029 Rev. *C 6 [+] Feedback CY8C24x23A Automotive Data Sheet PSoC® Overview Document Conventions Table of Contents Acronyms Used The following table lists the acronyms that are used in this document. Acronym Description AC alternating current ADC analog-to-digital converter API application programming interface CPU central processing unit CT continuous time DAC digital-to-analog converter DC direct current ECO external crystal oscillator EEPROM electrically erasable programmable read-only memory FSR full scale range GPIO general purpose IO GUI graphical user interface HBM human body model ICE in-circuit emulator ILO internal low speed oscillator IMO internal main oscillator IO input/output IPOR imprecise power on reset LSb least-significant bit LVD low voltage detect MSb most-significant bit PC program counter PLL phase-locked loop POR power on reset PPOR precision power on reset PSoC™ Programmable System-on-Chip™ PWM pulse width modulator SC switched capacitor SRAM static random access memory For an in depth discussion and more information on your PSoC device, obtain the PSoC Mixed-Signal Array Technical Reference Manual. This document encompasses and is organized into the following chapters and sections. 1. Pin Information ............................................................. 8 1.1 Pinouts ................................................................... 8 1.1.1 20-Pin Part Pinout ..................................... 8 1.1.2 28-Pin Part Pinout ..................................... 9 2. Register Reference ..................................................... 10 2.1 Register Conventions ........................................... 10 2.1.1 Abbreviations Used .................................. 10 2.2 Register Mapping Tables ..................................... 10 3. Electrical Specifications ............................................ 13 3.1 Absolute Maximum Ratings ................................ 14 3.2 Operating Temperature ....................................... 14 3.3 DC Electrical Characteristics ................................ 15 3.3.1 DC Chip-Level Specifications ................... 15 3.3.2 DC General Purpose IO Specifications .... 15 3.3.3 DC Operational Amplifier Specifications ... 16 3.3.4 DC Low Power Comparator Specifications 16 3.3.5 DC Analog Output Buffer Specifications ... 17 3.3.6 DC Analog Reference Specifications ....... 18 3.3.7 DC Analog PSoC Block Specifications ..... 19 3.3.8 DC POR and LVD Specifications ............. 19 3.3.9 DC Programming Specifications ............... 20 3.4 AC Electrical Characteristics ................................ 21 3.4.1 AC Chip-Level Specifications ................... 21 3.4.2 AC General Purpose IO Specifications .... 23 3.4.3 AC Operational Amplifier Specifications ... 24 3.4.4 AC Low Power Comparator Specifications 24 3.4.5 AC Digital Block Specifications ................. 26 3.4.6 AC Analog Output Buffer Specifications ... 27 3.4.7 AC External Clock Specifications ............. 27 3.4.8 AC Programming Specifications ............... 27 3.4.9 AC I2C Specifications ............................... 28 4. Packaging Information ............................................... 29 4.1 Packaging Dimensions ......................................... 29 4.2 Thermal Impedances .......................................... 30 4.3 Capacitance on Crystal Pins ............................... 30 4.4 Solder Reflow Peak Temperature ........................ 31 5. Ordering Information .................................................. 32 5.1 Ordering Code Definitions ................................... 32 6. Sales and Company Information ............................... 33 6.1 Revision History .................................................. 33 6.2 Copyrights and Flash Code Protection ................ 33 Units of Measure A units of measure table is located in the Electrical Specifications section. Table 3-1 on page 13 lists all the abbreviations used to measure the PSoC devices. Numeric Naming Hexidecimal numbers are represented with all letters in uppercase with an appended lowercase ‘h’ (for example, ‘14h’ or ‘3Ah’). Hexidecimal numbers may also be represented by a ‘0x’ prefix, the C coding convention. Binary numbers have an appended lowercase ‘b’ (e.g., 01010100b’ or ‘01000011b’). Numbers not indicated by an ‘h’ or ‘b’ are decimal. October 9, 2006 Document No. 38-12029 Rev. *C 7 [+] Feedback 1. Pin Information This chapter describes, lists, and illustrates the CY8C24x23A automotive PSoC device pins and pinout configurations. 1.1 Pinouts The CY8C24x23A automotive PSoC device is available in a variety of packages which are listed and illustrated in the following tables. Every port pin (labeled with a “P”) is capable of Digital IO. However, Vss, Vdd, and XRES are not capable of Digital IO. 1.1.1 20-Pin Part Pinout Table 1-1. 20-Pin Part Pinout (SSOP) Pin No. Type Digital Analog Pin Name Description 1 IO I P0[7] Analog column mux input. 2 IO IO P0[5] Analog column mux input and column output. 3 IO IO P0[3] Analog column mux input and column output. 4 IO I P0[1] Analog column mux input. 5 Vss Ground connection. 6 IO Power P1[7] I2C Serial Clock (SCL). 7 IO P1[5] I2C Serial Data (SDA). 8 IO P1[3] 9 IO P1[1] 10 Power Crystal Input (XTALin), I2C Serial Clock (SCL), ISSP-SCLK*. Vss Ground connection. 11 IO P1[0] Crystal Output (XTALout), I2C Serial Data (SDA), ISSP-SDATA*. 12 IO P1[2] 13 IO P1[4] 14 IO P1[6] 15 Input XRES Active high external reset with internal pull down. IO I P0[0] Analog column mux input. 17 IO I P0[2] Analog column mux input. 18 IO I P0[4] Analog column mux input. 19 IO I P0[6] Analog column mux input. Vdd Supply voltage. Power A, I, P0[7] A, IO, P0[5] A, IO, P0[3] A, I, P0[1] Vss I2CSCL,P1[7] I2C SDA,P1[5] P1[3] I2CSCL, XTALin,P1[1] Vss 1 2 3 4 5 6 7 8 9 10 SSOP 20 19 18 17 16 15 14 13 12 11 Vdd P0[6], A, I P0[4], A, I P0[2], A, I P0[0], A, I XRES P1[6] P1[4],EXTCLK P1[2] P1[0],XTALout,I2CSDA Optional External Clock Input (EXTCLK). 16 20 CY8C24223A 20-Pin PSoC Device LEGEND: A = Analog, I = Input, and O = Output. * These are the ISSP pins, which are not High Z at POR (Power On Reset). See the PSoC Mixed-Signal Array Technical Reference Manual for details. October 9, 2006 Document No. 38-12029 Rev. *C 8 [+] Feedback CY8C24x23A Automotive Data Sheet 1.1.2 1. Pin Information 28-Pin Part Pinout Table 1-2. 28-Pin Part Pinout (SSOP) Pin No. Type Digital Analog Pin Name 1 IO I P0[7] Analog column mux input. 2 IO IO P0[5] Analog column mux input and column output. 3 IO IO P0[3] Analog column mux input and column output. 4 IO I P0[1] Analog column mux input. 5 IO 6 IO 7 IO I P2[3] Direct switched capacitor block input. 8 IO I P2[1] Direct switched capacitor block input. 9 P2[7] P2[5] Power Vss Ground connection. 10 IO P1[7] I2C Serial Clock (SCL). 11 IO P1[5] I2C Serial Data (SDA). 12 IO P1[3] 13 IO P1[1] 14 Power Crystal Input (XTALin), I2C Serial Clock (SCL), ISSP-SCLK*. Vss Ground connection. 15 IO P1[0] Crystal Output (XTALout), I2C Serial Data (SDA), ISSP-SDATA*. 16 IO P1[2] 17 IO P1[4] 18 IO P1[6] 19 Input XRES Active high external reset with internal pull down. IO I P2[0] Direct switched capacitor block input. 21 IO I P2[2] Direct switched capacitor block input. 22 IO P2[4] External Analog Ground (AGND). 23 IO P2[6] External Voltage Reference (VRef). 24 IO I P0[0] Analog column mux input. 25 IO I P0[2] Analog column mux input. 26 IO I P0[4] Analog column mux input. 27 IO I P0[6] Analog column mux input. Vdd Supply voltage. Power A, I, P0[7] A, IO, P0[5] A, IO, P0[3] A, I, P0[1] P2[7] P2[5] A, I, P2[3] A, I, P2[1] Vss I2CSCL,P1[7] I2CSDA, P1[5] P1[3] I2CSCL,XTALin, P1[1] Vss 1 2 3 4 5 6 7 8 9 10 11 12 13 14 SSOP 28 27 26 25 24 23 22 21 20 19 18 17 16 15 Vdd P0[6], A, I P0[4], A, I P0[2], A, I P0[0], A, I P2[6],ExternalVRef P2[4],ExternalAGND P2[2], A, I P2[0], A, I XRES P1[6] P1[4],EXTCLK P1[2] P1[0],XTALout,I2CSDA Optional External Clock Input (EXTCLK). 20 28 CY8C24423A 28-Pin PSoC Device Description LEGEND: A = Analog, I = Input, and O = Output. * These are the ISSP pins, which are not High Z at POR (Power On Reset). See the PSoC Mixed-Signal Array Technical Reference Manual for details. October 9, 2006 Document No. 38-12029 Rev. *C 9 [+] Feedback 2. Register Reference This chapter lists the registers of the CY8C24x23A automotive PSoC device. For detailed register information, reference the PSoC Mixed-Signal Array Technical Reference Manual. 2.1 2.1.1 Register Conventions 2.2 Abbreviations Used The register conventions specific to this section are listed in the following table. Convention R Description Read register or bit(s) W Write register or bit(s) L Logical register or bit(s) C Clearable register or bit(s) # Access is bit specific October 9, 2006 Register Mapping Tables The PSoC device has a total register address space of 512 bytes. The register space is referred to as IO space and is divided into two banks. The XOI bit in the Flag register (CPU_F) determines which bank the user is currently in. When the XOI bit is set the user is in Bank 1. Note In the following register mapping tables, blank fields are Reserved and should not be accessed. Document No. 38-12029 Rev. *C 10 [+] Feedback CY8C24x23A Automotive Data Sheet 2. Register Reference Register Map Bank 0 Table: User Space RW RW RW RW RW RW RW RW I2C_CFG I2C_SCR I2C_DR I2C_MSCR INT_CLR0 INT_CLR1 INT_CLR3 INT_MSK3 INT_MSK0 INT_MSK1 INT_VC RES_WDT DEC_DH DEC_DL DEC_CR0 DEC_CR1 MUL_X MUL_Y MUL_DH MUL_DL ACC_DR1 ACC_DR0 ACC_DR3 ACC_DR2 RW RW RW RW RW RW RW CPU_F CPU_SCR1 CPU_SCR0 Document No. 38-12029 Rev. *C Access RW RW RW RW RW RW RW RW Addr (0,Hex) Name 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F ASD20CR0 90 ASD20CR1 91 ASD20CR2 92 ASD20CR3 93 ASC21CR0 94 ASC21CR1 95 ASC21CR2 96 ASC21CR3 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF RDI0RI B0 RDI0SYN B1 RDI0IS B2 RDI0LT0 B3 RDI0LT1 B4 RDI0RO0 B5 RDI0RO1 B6 B7 B8 B9 BA BB BC BD BE BF # Access is bit specific. Access October 9, 2006 ASC10CR0 ASC10CR1 ASC10CR2 ASC10CR3 ASD11CR0 ASD11CR1 ASD11CR2 ASD11CR3 Addr (0,Hex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lank fields are Reserved and should not be accessed. Name Access Addr (0,Hex) Name Access Addr (0,Hex) Name PRT0DR PRT0IE PRT0GS PRT0DM2 PRT1DR PRT1IE PRT1GS PRT1DM2 PRT2DR PRT2IE PRT2GS PRT2DM2 C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF RW # RW # RW RW RW RW RW RW RC W RC RC RW RW W W R R RW RW RW RW RL # # 11 [+] Feedback CY8C24x23A Automotive Data Sheet 2. Register Reference Register Map Bank 1 Table: Configuration Space RW RW RW RW RW RW RW C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF GDI_O_IN D0 GDI_E_IN D1 GDI_O_OU D2 GDI_E_OU D3 D4 D5 D6 D7 D8 D9 DA DB DC OSC_GO_EN DD OSC_CR4 DE OSC_CR3 DF OSC_CR0 E0 OSC_CR1 E1 OSC_CR2 E2 VLT_CR E3 VLT_CMP E4 E5 E6 E7 IMO_TR E8 ILO_TR E9 BDG_TR EA ECO_TR EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 CPU_F F7 F8 F9 FA FB FC FD CPU_SCR1 FE CPU_SCR0 FF Document No. 38-12029 Rev. *C Access RW RW RW RW RW RW RW RW Addr (1,Hex) RW RW RW RW RW RW RW RW Name 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F ASD20CR0 90 ASD20CR1 91 ASD20CR2 92 ASD20CR3 93 ASC21CR0 94 ASC21CR1 95 ASC21CR2 96 ASC21CR3 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF RDI0RI B0 RDI0SYN B1 RDI0IS B2 RDI0LT0 B3 RDI0LT1 B4 RDI0RO0 B5 RDI0RO1 B6 B7 B8 B9 BA BB BC BD BE BF # Access is bit specific. Access October 9, 2006 ASC10CR0 ASC10CR1 ASC10CR2 ASC10CR3 ASD11CR0 ASD11CR1 ASD11CR2 ASD11CR3 Addr (1,Hex) 00 RW 40 01 RW 41 02 RW 42 03 RW 43 04 RW 44 05 RW 45 06 RW 46 07 RW 47 08 RW 48 09 RW 49 0A RW 4A 0B RW 4B 0C 4C 0D 4D 0E 4E 0F 4F 10 50 11 51 12 52 13 53 14 54 15 55 16 56 17 57 18 58 19 59 1A 5A 1B 5B 1C 5C 1D 5D 1E 5E 1F 5F DBB00FN 20 RW CLK_CR0 60 RW DBB00IN 21 RW CLK_CR1 61 RW DBB00OU 22 RW ABF_CR0 62 RW 23 AMD_CR0 63 RW DBB01FN 24 RW 64 DBB01IN 25 RW 65 DBB01OU 26 RW AMD_CR1 66 RW 27 ALT_CR0 67 RW DCB02FN 28 RW 68 DCB02IN 29 RW 69 DCB02OU 2A RW 6A 2B 6B DCB03FN 2C RW 6C DCB03IN 2D RW 6D DCB03OU 2E RW 6E 2F 6F 30 ACB00CR3 70 RW 31 ACB00CR0 71 RW 32 ACB00CR1 72 RW 33 ACB00CR2 73 RW 34 ACB01CR3 74 RW 35 ACB01CR0 75 RW 36 ACB01CR1 76 RW 37 ACB01CR2 77 RW 38 78 39 79 3A 7A 3B 7B 3C 7C 3D 7D 3E 7E 3F 7F Blank fields are Reserved and should not be accessed. Name Access Addr (1,Hex) Name Access Addr (1,Hex) Name PRT0DM0 PRT0DM1 PRT0IC0 PRT0IC1 PRT1DM0 PRT1DM1 PRT1IC0 PRT1IC1 PRT2DM0 PRT2DM1 PRT2IC0 PRT2IC1 RW RW RW RW RW RW RW RW RW RW RW R W W RW W RL # # 12 [+] Feedback 3. Electrical Specifications This chapter presents the DC and AC electrical specifications of the CY8C24x23A automotive PSoC device. For the most up to date electrical specifications, confirm that you have the most recent data sheet by going to the web at http://www.cypress.com/psoc. Specifications are valid for -40oC ≤ TA ≤ 125oC and TJ ≤ 135oC, except where noted. 5.25 Valid Operating Region 4.75 Vdd Voltage 3.00 93 kHz 12 MHz 24 MHz CPUFrequency Figure 3-1. Voltage versus CPU Frequency The following table lists the units of measure that are used in this chapter. Table 3-1: Units of Measure Symbol Unit of Measure Symbol Unit of Measure degree Celsius µW microwatts dB decibels mA milli-ampere fF femto farad ms milli-second Hz hertz mV milli-volts KB 1024 bytes nA nanoampere Kbit 1024 bits ns nanosecond kHz kilohertz nV nanovolts kΩ kilohm Ω ohm MHz megahertz pA picoampere MΩ megaohm pF picofarad µA microampere pp peak-to-peak µF microfarad ppm µH microhenry ps picosecond µs microsecond sps samples per second µV microvolts σ sigma: one standard deviation microvolts root-mean-square V volts o C µVrms October 9, 2006 parts per million Document No. 38-12029 Rev. *C 13 [+] Feedback CY8C24x23A Automotive Data Sheet 3.1 3. Electrical Specifications Absolute Maximum Ratings Table 3-2. Absolute Maximum Ratings Symbol Description Min Typ Max Units TSTG Storage Temperature -55 +25 +125 oC TA Ambient Temperature with Power Applied -40 – +125 o Vdd Supply Voltage on Vdd Relative to Vss -0.5 – +5.75 V VIO DC Input Voltage Vss - 0.5 – Vdd + 0.5 V VIOZ DC Voltage Applied to Tri-state Vss - 0.5 – Vdd + 0.5 V IMIO Maximum Current into any Port Pin -25 – +25 mA ESD Electro Static Discharge Voltage 2000 – – V LU Latch-up Current – – 200 mA 3.2 Notes Higher storage temperatures will reduce data retention time. Recommended storage temperature is +25°C ± 25°C. Storage temperatures above 65oC will degrade reliability. Maximum combined storage and operational time at +125°C is 7000 hours. C Human Body Model ESD. Operating Temperature Table 3-3. Operating Temperature Symbol Description Min Typ Max Units TA Ambient Temperature -40 – +125 o TJ Junction Temperature -40 – +135 oC October 9, 2006 Document No. 38-12029 Rev. *C Notes C The temperature rise from ambient to junction is package specific. See “Thermal Impedances” on page 30. The user must limit the power consumption to comply with this requirement. 14 [+] Feedback CY8C24x23A Automotive Data Sheet 3.3 3.3.1 3. Electrical Specifications DC Electrical Characteristics DC Chip-Level Specifications The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-4. DC Chip-Level Specifications Symbol Description Min Typ Max Units Vdd Supply Voltage 4.75 – 5.25 V IDD Supply Current – 5 8 mA Notes Conditions are Vdd = 5.25V, -40 oC ≤ TA ≤ 125 o C, CPU = 3 MHz, SYSCLK doubler disabled, VC1 = 1.5 MHz, VC2 = 93.75 kHz, VC3 = 93.75 kHz, analog power = off. ISB Sleep (Mode) Current with POR, LVD, Sleep Timer, and WDT.a – 4 13 µA Conditions are with internal slow speed oscillator, Vdd = 5.25V, -40 oC ≤ TA ≤ 55 oC. Analog power = off. ISBH Sleep (Mode) Current with POR, LVD, Sleep Timer, and WDT at high temperature.a – 4 100 µA Conditions are with internal slow speed oscillator, Vdd = 5.25V, 55 oC < TA ≤ 125 oC. Analog power = off. ISBXTL Sleep (Mode) Current with POR, LVD, Sleep Timer, WDT, and external crystal.a – 6 15 µA Conditions are with properly loaded, 1 µW max, 32.768 kHz crystal. Vdd = 5.25V, -40 oC ≤ TA ≤ ISBXTLH Sleep (Mode) Current with POR, LVD, Sleep Timer, WDT, and external crystal at high temperature.a – 6 100 µA Conditions are with properly loaded, 1µW max, 32.768 kHz crystal. Vdd = 5.25V, 55 oC < TA ≤ VREF Reference Voltage (Bandgap) 1.25 1.3 1.35 V Trimmed for appropriate Vdd. 55 oC. Analog power = off. 125oC. Analog power = off. a. Standby current includes all functions (POR, LVD, WDT, Sleep Time) needed for reliable system operation. This should be compared with devices that have similar functions enabled. 3.3.2 DC General Purpose IO Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance. Table 3-5. DC GPIO Specifications Symbol Description Min Typ Max Units Notes kΩ RPU Pull up Resistor RPD Pull down Resistor 4 5.6 8 kΩ VOH High Output Level 3.5 – – V IOH = 10 mA, Vdd = 4.75 to 5.25V (8 total loads, 4 on even port pins (for example, P0[2], P1[4]), 4 on odd port pins (for example, P0[3], P1[5])). VOL Low Output Level – – 0.75 V IOL = 25 mA, Vdd = 4.75 to 5.25V (8 total loads, 4 on even port pins (for example, P0[2], P1[4]), 4 on odd port pins (for example, P0[3], P1[5])). Total IOL budget of 150 mA. 0.8 V Vdd = 4.75 to 5.25 V Vdd = 4.75 to 5.25 4 5.6 8 VIL Input Low Level – – VIH Input High Level 2.2 – VH Input Hysterisis – 60 – mV IIL Input Leakage (Absolute Value) – 1 – nA Gross tested to 1 µA. CIN Capacitive Load on Pins as Input – 3.5 10 pF Package and pin dependent. Temp = 25oC. COUT Capacitive Load on Pins as Output – 3.5 10 pF Package and pin dependent. Temp = 25oC. October 9, 2006 Document No. 38-12029 Rev. *C 15 [+] Feedback CY8C24x23A Automotive Data Sheet 3.3.3 3. Electrical Specifications DC Operational Amplifier Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. The Operational Amplifier is a component of both the Analog Continuous Time PSoC blocks and the Analog Switched Cap PSoC blocks. The guaranteed specifications are measured in the Analog Continuous Time PSoC block. Table 3-6. DC Operational Amplifier Specifications Symbol Description Min Typ Max Units Input Offset Voltage (absolute value) Low Power – 1.6 11 mV Input Offset Voltage (absolute value) Mid Power – 1.3 9 mV Input Offset Voltage (absolute value) High Power – 1.2 9 mV TCVOSOA Input Offset Voltage Drift – 7.0 35.0 µV/oC VOSOA Notes IEBOA Input Leakage Current (Port 0 Analog Pins) – 200 – pA Gross tested to 1 µA. CINOA Input Capacitance (Port 0 Analog Pins) – 4.5 10 pF Package and pin dependent. Temp = 25oC. VCMOA Common Mode Voltage Range 0.0 – Vdd V Common Mode Voltage Range (high power or high opamp bias) 0.5 – Vdd - 0.5 The common-mode input voltage range is measured through an analog output buffer. The specification includes the limitations imposed by the characteristics of the analog output buffer. Power = Low – 80 dB Power = Medium – 80 dB Power = High – 80 dB Power = Low Vdd - 0.2 – – V Power = Medium Vdd - 0.2 – – V Power = High Vdd - 0.5 – – V Power = Low – – 0.2 V Power = Medium – – 0.2 V Power = High – – 0.5 V Power = Low – 150 200 µA Power = Low, Opamp Bias = High – 300 400 µA Power = Medium – 600 800 µA Power = Medium, Opamp Bias = High – 1200 1600 µA Power = High – 2400 3200 µA Power = High, Opamp Bias = High – 4600 6400 µA Supply Voltage Rejection Ratio – 80 – dB GOLOA VOHIGHOA VOLOWOA ISOA PSRROA 3.3.4 Open Loop Gain Specification is applicable at high power. For all other bias modes (except high power, high opamp bias), minimum is 60 dB. High Output Voltage Swing (worst case internal load) Low Output Voltage Swing (worst case internal load) Supply Current (including associated AGND buffer) Vss ≤ VIN ≤ (Vdd - 2.25) or (Vdd - 1.25V) ≤ VIN ≤ Vdd. DC Low Power Comparator Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-7. DC Low Power Comparator Specifications Symbol Description Min Typ Max Units VREFLPC Low power comparator (LPC) reference voltage range 0.2 – Vdd - 1 V ISLPC LPC supply current – 10 40 µA VOSLPC LPC voltage offset – 2.5 30 mV October 9, 2006 Document No. 38-12029 Rev. *C Notes 16 [+] Feedback CY8C24x23A Automotive Data Sheet 3.3.5 3. Electrical Specifications DC Analog Output Buffer Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-8. DC Analog Output Buffer Specifications Symbol Description Min Typ Max Units VOSOB Input Offset Voltage (Absolute Value) – 3 18 mV TCVOSOB Input Offset Voltage Drift – +6 – µV/°C VCMOB Common-Mode Input Voltage Range 0.5 – Vdd - 1.0 V ROUTOB Output Resistance – 1 – Ω VOHIGHOB High Output Voltage Swing (Load = 32 ohms to Vdd/2) 0.5 x Vdd + 1.1 – – V VOLOWOB Low Output Voltage Swing (Load = 32 ohms to Vdd/2) – – 0.5 x Vdd - 1.3 V ISOB Supply Current Including Bias Cell (No Load) Power = Low – 1.1 5.1 mA Power = High – 2.6 8.8 mA Supply Voltage Rejection Ratio – 64 – dB PSRROB October 9, 2006 Document No. 38-12029 Rev. *C Notes 17 [+] Feedback CY8C24x23A Automotive Data Sheet 3.3.6 3. Electrical Specifications DC Analog Reference Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. The guaranteed specifications are measured through the Analog Continuous Time PSoC blocks. The power levels for AGND refer to the power of the Analog Continuous Time PSoC block. The power levels for RefHi and RefLo refer to the Analog Reference Control register. The limits stated for AGND include the offset error of the AGND buffer local to the Analog Continuous Time PSoC block. Table 3-9. DC Analog Reference Specifications Symbol Description BG Bandgap Voltage Reference – AGND = Vdd/2a Min CT Block Power = High – AGND = 2 x AGND = P2[4] (P2[4] = Vdd/2 - 0.02 Vdd/2 Vdd/2 + 0.02 V 2.4 2.6 2.8 V P2[4] - 0.02 P2[4] P2[4] + 0.02 V 1.23 1.30 1.37 V 1.98 2.08 2.14 V -0.035 0.000 0.035 V Vdd/2 + 1.15 Vdd/2 +1.30 Vdd/2 +1.45 V 3.65 3.9 4.15 V P2[6] + 2.4 P2[6] + 2.6 P2[6] + 2.8 V P2[4] + 1.24 P2[4] +1.30 P2[4] + 1.36 V P2[4] + P2[6] - 0.1 P2[4] + P2[6] P2[4] + P2[6] + 0.1 V 3.9 4.16 4.42 V Vdd/2 - 1.45 Vdd/2 - 1.3 1.15 V 1.15 1.3 1.45 V 2.4 - P2[6] 2.6 - P2[6] 2.8 - P2[6] V P2[4] - 1.45 1.3 P2[4] - 1.15 V P2[4] - P2[6] - 0.1 P2[4] - P2[6] P2[4] - P2[6] + 0.1 V AGND = BandGap a AGND = 1.6 x BandGap CT Block Power = High – V a CT Block Power = High – Units 1.35 Vdd/2)a CT Block Power = High – Max 1.30 BandGapa CT Block Power = High – Typ 1.25 AGND Column to Column Variation (AGND = Vdd/2) CT Block Power = High – RefHi = Vdd/2 + BandGap – RefHi = 3 x BandGap – RefHi = 2 x BandGap + P2[6] (P2[6] = 1.3V) – RefHi = P2[4] + BandGap (P2[4] = Vdd/2) – RefHi = P2[4] + P2[6] (P2[4] = Vdd/2, P2[6] = 1.3V) – RefHi = 3.2 x BandGap – RefLo = Vdd/2 – BandGap – RefLo = BandGap – RefLo = 2 x BandGap - P2[6] (P2[6] = 1.3V) – RefLo = P2[4] – BandGap (P2[4] = Vdd/2) – RefLo = P2[4]-P2[6] (P2[4] = Vdd/2, P2[6] = 1.3V) Ref Control Power = High Ref Control Power = High Ref Control Power = High Ref Control Power = High Ref Control Power = High Ref Control Power = High Ref Control Power = High Ref Control Power = High Ref Control Power = High Ref Control Power = High Ref Control Power = High a a. AGND tolerance includes the offsets of the local buffer in the PSoC block. Bandgap voltage is 1.3V ± 0.05V. October 9, 2006 Document No. 38-12029 Rev. *C 18 [+] Feedback CY8C24x23A Automotive Data Sheet 3.3.7 3. Electrical Specifications DC Analog PSoC Block Specifications The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-10. DC Analog PSoC Block Specifications Symbol Description Min Typ Max Units RCT Resistor Unit Value (Continuous Time) – 12.24 – kΩ CSC Capacitor Unit Value (Switch Cap) – 80 – fF 3.3.8 Notes DC POR and LVD Specifications The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Note The bits PORLEV and VM in the table below refer to bits in the VLT_CR register. See the PSoC Mixed-Signal Array Technical Reference Manual for more information on the VLT_CR register. Table 3-11. DC POR and LVD Specifications Symbol Description Min Typ Max Units Notes Vdd Value for PPOR Trip (positive ramp) VPPOR2R PORLEV[1:0] = 10b 4.55 4.70 V Vdd Value for PPOR Trip (negative ramp) VPPOR2 PORLEV[1:0] = 10b 4.55 V PPOR Hysteresis VPH2 PORLEV[1:0] = 10b – 0 – mV Vdd Value for LVD Trip VLVD6 VM[2:0] = 110b 4.62 4.73 4.83 V VLVD7 VM[2:0] = 111b 4.710 4.814 4.950 V October 9, 2006 Document No. 38-12029 Rev. *C 19 [+] Feedback CY8C24x23A Automotive Data Sheet 3.3.9 3. Electrical Specifications DC Programming Specifications The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-12. DC Programming Specifications Symbol Description Min Typ Max Units Notes VddIWRITE Supply Voltage for Flash Write Operations 4.75 – – V IDDP Supply Current During Programming or Verify – 10 25 mA VILP Input Low Voltage During Programming or Verify – – 0.8 V VIHP Input High Voltage During Programming or Verify 2.2 – – V IILP Input Current when Applying Vilp to P1[0] or P1[1] During Programming or Verify – – 0.2 mA Driving internal pull-down resistor. IIHP Input Current when Applying Vihp to P1[0] or P1[1] During Programming or Verify – – 1.5 mA Driving internal pull-down resistor. VOLV Output Low Voltage During Programming or Verify – – Vss + 0.75 V VOHV Output High Voltage During Programming or Verify 3.5 – Vdd V 100 – – – Erase/write cycles per block. 6,400 – – – Erase/write cycles. 15 – – Years FlashENPB FlashENT FlashDR a Flash Endurance (per block) Flash Endurance (total)a,b Flash Data Retention c a. For the full temperature range, the user must employ a temperature sensor user module (FlashTemp) and feed the result to the temperature argument before writing. Refer to the Flash APIs Application Note AN2015 at http://www.cypress.com under Application Notes for more information. b. A maximum of 64 x 100 block endurance cycles is allowed. c. Flash data retention based on the use condition of ≤ 7000 hours at TA ≤ 125°C and the remaining time at TA ≤ 65°C. October 9, 2006 Document No. 38-12029 Rev. *C 20 [+] Feedback CY8C24x23A Automotive Data Sheet 3.4 3. Electrical Specifications AC Electrical Characteristics 3.4.1 AC Chip-Level Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-13. AC Chip-Level Specifications Symbol Description Min Typ Max Units Notes FIMO24 Internal Main Oscillator Frequency for 24 MHz 22.95 24 24.96 MHz Trimmed. Utilizing factory trim values. FCPU1 CPU Frequency (5V Nominal) 0.09 12 12.48 MHz F48M Digital PSoC Block Frequency – – – MHz F24M Digital PSoC Block Frequency 0 24 24.96a MHz F32K1 Internal Low Speed Oscillator Frequency 15 32 64 kHz F32K2 External Crystal Oscillator – 32.768 – kHz Accuracy is capacitor and crystal dependent. 50% duty cycle. FPLL PLL Frequency – 23.986 – MHz Is a multiple (x732) of crystal frequency. Jitter24M2 24 MHz Period Jitter (PLL) – – 800 ps TPLLSLEW PLL Lock Time 0.5 – 10 ms TPLLSLEWS- PLL Lock Time for Low Gain Setting 0.5 – 50 ms TOS External Crystal Oscillator Startup to 1% – 1700 2620 ms TOSACC External Crystal Oscillator Startup to 100 ppm – 2800 3800 ms Jitter32k 32 kHz Period Jitter – 100 TXRST External Reset Pulse Width 10 – – µs DC24M 24 MHz Duty Cycle 40 50 60 % Step24M 24 MHz Trim Step Size – 50 – kHz Jitter24M1P 24 MHz Period Jitter (IMO) Peak-to-Peak – 300 Jitter24M1R 24 MHz Period Jitter (IMO) Root Mean Squared – – 600 ps FMAX Maximum frequency of signal on row input or row output. – – 12.48 MHz TRAMP Supply Ramp Time 0 – – µs Not allowed. LOW ns ps a. See the individual user module data sheets for information on maximum frequencies for user modules. PLL Enable TPLLSLEW 24 MHz FPLL PLL Gain 0 Figure 3-2. PLL Lock Timing Diagram October 9, 2006 Document No. 38-12029 Rev. *C 21 [+] Feedback CY8C24x23A Automotive Data Sheet 3. Electrical Specifications PLL Enable TPLLSLEWLOW 24 MHz FPLL PLL Gain 1 Figure 3-3. PLL Lock for Low Gain Setting Timing Diagram 32K Select 32 kHz TOS F32K2 Figure 3-4. External Crystal Oscillator Startup Timing Diagram Jitter24M1 F 24M Figure 3-5. 24 MHz Period Jitter (IMO) Timing Diagram Jitter32k F 32K2 Figure 3-6. 32 kHz Period Jitter (ECO) Timing Diagram October 9, 2006 Document No. 38-12029 Rev. *C 22 [+] Feedback CY8C24x23A Automotive Data Sheet 3.4.2 3. Electrical Specifications AC General Purpose IO Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-14. AC GPIO Specifications Symbol Description FGPIO Min GPIO Operating Frequency 0 Typ – Max 12.48 Units MHz Notes Normal Strong Mode TRiseF Rise Time, Normal Strong Mode, Cload = 50 pF 2 – 22 ns Vdd = 4.75 to 5.25V, 10% - 90% TFallF Fall Time, Normal Strong Mode, Cload = 50 pF 2 – 22 ns Vdd = 4.75 to 5.25V, 10% - 90% TRiseS Rise Time, Slow Strong Mode, Cload = 50 pF 9 27 – ns Vdd = 4.75 to 5.25V, 10% - 90% TFallS Fall Time, Slow Strong Mode, Cload = 50 pF 9 22 – ns Vdd = 4.75 to 5.25V, 10% - 90% 90% GPIO Pin Output Voltage 10% TRiseF TRiseS TFallF TFallS Figure 3-7. GPIO Timing Diagram October 9, 2006 Document No. 38-12029 Rev. *C 23 [+] Feedback CY8C24x23A Automotive Data Sheet 3.4.3 3. Electrical Specifications AC Operational Amplifier Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Note Settling times, slew rates, and gain bandwidth are based on the Analog Continuous Time PSoC block. Table 3-15. AC Operational Amplifier Specifications Symbol SRROA SRFOA BWOA 3.4.4 Description Min Typ Max Units Notes Rising Slew Rate (20% to 80%)(10 pF load, Unity Gain) V/µs Power = Low 0.15 Power = Low, Opamp Bias = High 0.15 – Power = Medium 0.15 Power = Medium, Opamp Bias = High 1.7 Power = High 1.7 Power = High, Opamp Bias = High 6.5 – V/µs Power = Low 0.01 – V/µs Power = Low, Opamp Bias = High 0.01 Power = Medium 0.01 Power = Medium, Opamp Bias = High 0.5 Power = High 0.5 Power = High, Opamp Bias = High 4.0 – V/µs Power = Low 0.75 – MHz Power = Low, Opamp Bias = High 0.75 Power = Medium 0.75 Power = Medium, Opamp Bias = High 3.1 Power = High 3.1 Power = High, Opamp Bias = High 5.4 V/µs V/µs V/µs – V/µs Falling Slew Rate (20% to 80%)(10 pF load, Unity Gain) V/µs V/µs V/µs – V/µs Gain Bandwidth Product MHz MHz MHz – MHz – MHz AC Low Power Comparator Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-16. AC Low Power Comparator Specifications Symbol TRLPC Description LPC response time October 9, 2006 Min – Typ – Max 50 Document No. 38-12029 Rev. *C Units µs Notes ≥ 50 mV overdrive comparator reference set within VREFLPC. 24 [+] Feedback CY8C24x23A Automotive Data Sheet 3. Electrical Specifications When bypassed by a capacitor on P2[4], the noise of the analog ground signal distributed to each block is reduced by a factor of up to 5 (14 dB). This is at frequencies above the corner frequency defined by the on-chip 8.1k resistance and the external capacitor. dBV/rtHz 10000 0 0.01 0.1 1.0 10 1000 100 0.001 0.01 0.1 Freq (kHz) 1 10 100 Figure 3-8. Typical AGND Noise with P2[4] Bypass At low frequencies, the opamp noise is proportional to 1/f, power independent, and determined by device geometry. At high frequencies, increased power level reduces the noise spectrum level. nV/rtHz 10000 PH_BH PH_BL PM_BL PL_BL 1000 100 10 0.001 0.01 0.1 Freq (kHz) 1 10 100 Figure 3-9. Typical Opamp Noise October 9, 2006 Document No. 38-12029 Rev. *C 25 [+] Feedback CY8C24x23A Automotive Data Sheet 3.4.5 3. Electrical Specifications AC Digital Block Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-17. AC Digital Block Specifications Function Description Min All Functions Maximum Block Clocking Frequency Timer Capture Pulse Width 50a Maximum Frequency, No Capture – Maximum Frequency, With Capture Counter Dead Band Typ Max Units 24.96 MHz – – ns – 24.96 MHz – – 24.96 MHz Enable Pulse Width 50a – – ns Maximum Frequency, No Enable Input – – 24.96 MHz Maximum Frequency, Enable Input – – 24.96 MHz Asynchronous Restart Mode 20 – – ns Synchronous Restart Mode 50a – – ns a 50 – – ns Notes 4.75V < Vdd < 5.25V. 4.75V < Vdd < 5.25V. Kill Pulse Width: Disable Mode Maximum Frequency – – 24.96 MHz 4.75V < Vdd < 5.25V. CRCPRS (PRS Mode) Maximum Input Clock Frequency – – 24.96 MHz 4.75V < Vdd < 5.25V. CRCPRS (CRC Mode) Maximum Input Clock Frequency – – 24.96 MHz SPIM Maximum Input Clock Frequency – – 4.1 MHz SPIS Maximum Input Clock Frequency – – 2.05 MHz Width of SS_ Negated Between Transmissions 50a – – ns Maximum Input Clock Frequency – – 8.2 MHz Transmitter Maximum data rate at 4.1 MHz due to 2 x over clocking. Maximum data rate at 3.08 MHz due to 8 x over clocking. Receiver Maximum Input Clock Frequency – 16 24.96 MHz Maximum data rate at 3.08 MHz due to 8 x over clocking. a. 50 ns minimum input pulse width is based on the input synchronizers running at 24 MHz (42 ns nominal period). October 9, 2006 Document No. 38-12029 Rev. *C 26 [+] Feedback CY8C24x23A Automotive Data Sheet 3.4.6 3. Electrical Specifications AC Analog Output Buffer Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-18. AC Analog Output Buffer Specifications Symbol TROB TSOB SRROB SRFOB BWOB BWOB 3.4.7 Description Min Typ Max Units Notes Rising Settling Time to 0.1%, 1V Step, 100pF Load Power = Low – – 3 µs Power = High – – 3 µs Power = Low – – 3 µs Power = High – – 3 µs Power = Low 0.6 – – V/µs Power = High 0.6 – – V/µs Power = Low 0.6 – – V/µs Power = High 0.6 – – V/µs Power = Low 0.8 – – MHz Power = High 0.8 – – MHz Power = Low 300 – – kHz Power = High 300 – – kHz Falling Settling Time to 0.1%, 1V Step, 100pF Load Rising Slew Rate (20% to 80%), 1V Step, 100pF Load Falling Slew Rate (80% to 20%), 1V Step, 100pF Load Small Signal Bandwidth, 20mVpp, 3dB BW, 100pF Load Large Signal Bandwidth, 1Vpp, 3dB BW, 100pF Load AC External Clock Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-19. AC External Clock Specifications Symbol Description Min Typ Max Units FOSCEXT Frequency 0 – 24.24 MHz – High Period 20.6 – – ns – Low Period 20.6 – – ns – Power Up IMO to Switch 150 – – µs 3.4.8 Notes AC Programming Specifications The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-20. AC Programming Specifications Symbol Description Min Typ Max Units TRSCLK Rise Time of SCLK 1 – 20 ns TFSCLK Fall Time of SCLK 1 – 20 ns TSSCLK Data Set up Time to Falling Edge of SCLK 40 – – ns THSCLK Data Hold Time from Falling Edge of SCLK 40 – – ns FSCLK Frequency of SCLK 0 – 8 MHz TERASEB Flash Erase Time (Block) – 15 – ms TWRITE Flash Block Write Time – 30 – ms TDSCLK Data Out Delay from Falling Edge of SCLK – – 45 ns October 9, 2006 Document No. 38-12029 Rev. *C Notes 27 [+] Feedback CY8C24x23A Automotive Data Sheet 3.4.9 3. Electrical Specifications AC I2C Specifications The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C ≤ TA ≤ 125°C. Typical parameters apply to 5V at 25°C and are for design guidance only. Table 3-21. AC Characteristics of the I2C SDA and SCL Pins Standard Mode Symbol Description Min Fast Mode Max Min Max Units FSCLI2C SCL Clock Frequency 0 100 0 400 kHz THDSTAI2C Hold Time (repeated) START Condition. After this period, the first clock pulse is generated. 4.0 – 0.6 – µs TLOWI2C LOW Period of the SCL Clock 4.7 – 1.3 – µs THIGHI2C HIGH Period of the SCL Clock 4.0 – 0.6 – µs TSUSTAI2C Set-up Time for a Repeated START Condition 4.7 – 0.6 – µs THDDATI2C Data Hold Time 0 – 0 – µs TSUDATI2C Data Set-up Time 250 – 100a – ns TSUSTOI2C Set-up Time for STOP Condition 4.0 – 0.6 – µs TBUFI2C Bus Free Time Between a STOP and START Condition 4.7 – 1.3 – µs TSPI2C Pulse Width of spikes are suppressed by the input filter. – 0 50 ns – Notes a. A Fast-Mode I2C-bus device can be used in a Standard-Mode I2C-bus system, but the requirement tSU;DAT ≥ 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line trmax + tSU;DAT = 1000 + 250 = 1250 ns (according to the Standard-Mode I2C-bus specification) before the SCL line is released. SDA TLOWI2C TSUDATI2C THDSTAI2C TSPI2C TBUFI2C SCL S THDSTAI2C THDDATI2C THIGHI2C TSUSTAI2C Sr TSUSTOI2C P S Figure 3-10. Definition for Timing for Fast/Standard Mode on the I2C Bus October 9, 2006 Document No. 38-12029 Rev. *C 28 [+] Feedback 4. Packaging Information This chapter illustrates the packaging specifications for the CY8C24x23A automotive PSoC device, along with the thermal impedances for each package and the typical package capacitance on crystal pins. Important Note Emulation tools may require a larger area on the target PCB than the chip’s footprint. For a detailed description of the emulation tools’ dimensions, refer to the document titled PSoC Emulator Pod Dimensions at http://www.cypress.com/design/MR10161. 4.1 Packaging Dimensions 51-85077 *C Figure 4-1. 20-Lead (210-Mil) SSOP October 9, 2006 Document No. 38-12029 Rev. *C 29 [+] Feedback CY8C24x23A Automotive Data Sheet 4. Packaging Information 51-85079 *C Figure 4-2. 28-Lead (210-Mil) SSOP 4.2 Thermal Impedances Table 4-1. Thermal Impedances per Package Package Typical θJA * 20 SSOP 117 oC/W 28 SSOP 101 oC/W * TJ = TA + POWER x θJA 4.3 Capacitance on Crystal Pins Table 4-2: Typical Package Capacitance on Crystal Pins Package Package Capacitance 20 SSOP 2.6 pF 28 SSOP 2.8 pF October 9, 2006 Document No. 38-12029 Rev. *C 30 [+] Feedback CY8C24x23A Automotive Data Sheet 4.4 4. Packaging Information Solder Reflow Peak Temperature Following is the minimum solder reflow peak temperature to achieve good solderability. Table 4-3. Solder Reflow Peak Temperature Package Minimum Peak Temperature* Maximum Peak Temperature 20 SSOP 240 C 260oC 28 SSOP 240oC 260oC o *Higher temperatures may be required based on the solder melting point. Typical temperatures for solder are 220 ± 5oC with Sn-Pb or 245 ± 5oC with Sn-Ag-Cu paste. Refer to the solder manufacturer specifications. October 9, 2006 Document No. 38-12029 Rev. *C 31 [+] Feedback 5. Ordering Information The following table lists the CY8C24x23A automotive PSoC device group’s key package features and ordering codes. RAM (Bytes) Switch Mode Pump Temperature Range Digital Blocks Analog Blocks Digital IO Pins Analog Inputs Analog Outputs XRES Pin CY8C24223A-12PVXE 4K 256 No -40C to +125C 4 6 16 8 2 Yes 20 Pin (210 Mil) SSOP (Tape and Reel) CY8C24223A-12PVXET 4K 256 No -40C to +125C 4 6 16 8 2 Yes 28 Pin (210 Mil) SSOP CY8C24423A-12PVXE 4K 256 No -40C to +125C 4 6 24 10 2 Yes 28 Pin (210 Mil) SSOP (Tape and Reel) CY8C24423A-12PVXET 4K 256 No -40C to +125C 4 6 24 10 2 Yes 5.1 Ordering Code 20 Pin (210 Mil) SSOP Package Flash (Bytes) Table 5-1. CY8C24x23A Automotive PSoC Key Features and Ordering Information Ordering Code Definitions CY 8 C 24 xxx-12xx Package Type: PX = PDIP Pb-Free SX = SOIC Pb-Free PVX = SSOP Pb-Free LFX = QFN Pb-Free LKX = QFN Pb-Free AX = TQFP Pb-Free Thermal Rating: C = Commercial I = Industrial E = Extended Speed: 12 MHz Part Number Family Code Technology Code: C = CMOS Marketing Code: 8 = Cypress PSoC Company ID: CY = Cypress October 9, 2006 Document No. 38-12029 Rev. *C 32 [+] Feedback 6. Sales and Company Information To obtain information about Cypress Semiconductor or PSoC sales and technical support, reference the following information. Cypress Semiconductor 198 Champion Court San Jose, CA 95134 408.943.2600 Web Links: 6.1 Company Information – http://www.cypress.com Sales – http://www.cypress.com/aboutus/sales_locations.cfm Technical Support – http://www.cypress.com/support/login.cfm Revision History Table 6-1. CY8C24x23A Automotive Data Sheet Revision History Document Title: CY8C24223A and CY8C24423A Automotive PSoC Mixed-Signal Array Final Data Sheet Document Number: 38-12029 Issue Date Origin of Change ** Revision 238268 ECN # See ECN SFV First release of CY8C24x23A Automotive Preliminary Data Sheet. *A 271471 See ECN HMT Update per SFV memo. Input MWR changes, including removing SMP. Change to Final. *B 286089 See ECN HMT Update characterization data. Fine tune pinouts. Add Reflow Peak Temp. table. *C 512475 See ECN HMT Add Low Power Comparator (LPC) AC/DC electrical spec. tables. Add ISSP note to pinout tables. Update typical and recommended Storage Temperature per extended temp. specs. Update CY branding and QFN convention. Update copyright and trademarks. Distribution: External/Public 6.2 Description of Change Posting: None Copyrights and Flash Code Protection Copyrights © Cypress Semiconductor Corp. 2004-2006. All rights reserved. PSoC Designer™, Programmable System-on-Chip™, and PSoC Express are trademarks and PSoC® is a registered trademark of Cypress Semiconductor Corp. All other trademarks or registered trademarks referenced herein are property of the respective corporations. The information contained herein is subject to change without notice. Cypress Semiconductor assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. Cypress Semiconductor products are not warranted nor intended to be used for medical, life-support, life-saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress Semiconductor. Flash Code Protection Note the following details of the Flash code protection features on Cypress Semiconductor PSoC devices. Cypress Semiconductor products meet the specifications contained in their particular data sheets. Cypress Semiconductor believes that its family of products is one of the most secure families of its kind on the market today, regardless of how they are used. There may be methods, unknown to Cypress Semiconductor, that can breach the code protection features. Any of these methods, to our knowledge, would be dishonest and possibly illegal. Neither Cypress Semiconductor nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Cypress Semiconductor is willing to work with the customer who is concerned about the integrity of their code. Code protection is constantly evolving. We at Cypress Semiconductor are committed to continuously improving the code protection features of our products. October 9, 2006 © Cypress Semiconductor Corp. 2004-2006 — Document No. 38-12029 Rev. *C 33 [+] Feedback