CY7C1069DV33 16-Mbit (2M x 8) Static RAM Features Functional Description ■ High speed ❐ tAA = 10 ns The CY7C1069DV33 is a high performance CMOS Static RAM organized as 2,097,152 words by 8 bits. ■ Low active power ❐ ICC = 175 mA at 10 ns ■ Low CMOS standby power ❐ ISB2 = 25 mA To write to the device, take Chip Enables (CE1 LOW and CE2 HIGH) and Write Enable (WE) input LOW. Data on the eight IO pins (IO0 through IO7) is then written into the location specified on the address pins (A0 through A20). To read from the device, take Chip Enables (CE1 LOW and CE2 HIGH) and Output Enable (OE) LOW while forcing the Write Enable (WE) HIGH. Under these conditions, the contents of the memory location specified by the address pins will appear on the IO pins. See Truth Table on page 8 for a complete description of Read and Write modes. ■ Operating voltages of 3.3 ± 0.3V ■ 2.0V data retention ■ Automatic power down when deselected ■ TTL compatible inputs and outputs ■ Easy memory expansion with CE1 and CE2 features ■ Available in Pb-free 54-Pin TSOP II and 48-Ball VFBGA packages The input and output pins (IO0 through IO7) are placed in a high impedance state when the device is deselected (CE1 HIGH or CE2 LOW), the outputs are disabled (OE HIGH), or during a write operation (CE1 LOW, CE2 HIGH, and WE LOW). The CY7C1069DV33 is available in a 54-pin TSOP II package with center power and ground (revolutionary) pinout, and a 48-Ball very fine pitch ball grid array (VFBGA) package. Logic Block Diagram 2M x 8 ARRAY SENSE AMPS A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 ROW DECODER INPUT BUFFER IO0 – IO7 WE CE2 OE COLUMN DECODER A10 A11 A 12 A 13 A 14 A15 A16 A17 A18 A19 A20 CE1 Cypress Semiconductor Corporation Document Number: 38-05478 Rev. *D • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised September 06, 2007 CY7C1069DV33 Selection Guide –10 Unit Maximum Access Time 10 ns Maximum Operating Current 175 mA Maximum CMOS Standby Current 25 mA Pin Configuration Figure 1. 54-Pin TSOP II (Top View) [1] NC VCC NC IO6 VSS IO7 A4 A3 A2 A1 A0 NC CE1 VCC WE CE2 A19 A18 A17 A16 A15 IO0 VCC IO1 NC VSS NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 45 44 NC VSS NC IO5 VCC IO4 A5 A6 A7 A8 A9 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 NC OE VSS NC A20 A10 A11 A12 A13 A14 IO3 VSS IO2 NC VCC NC 54 53 52 51 50 49 48 47 46 Figure 2. 48-Ball VFBGA (Top View) [1] 1 2 3 4 5 6 NC OE A0 A1 A2 CE2 A NC NC A3 A4 CE1 NC B IO0 NC A5 A6 NC IO4 C VSS IO1 A17 A7 IO5 VCC D VCC IO2 A18 A16 IO6 VSS E IO3 NC A14 A15 NC IO7 F NC NC A12 A13 WE NC G A19 A8 A9 A10 A11 A20 H Note 1. NC pins are not connected on the die. Document Number: 38-05478 Rev. *D Page 2 of 10 CY7C1069DV33 Maximum Ratings Current into Outputs (LOW) ........................................ 20 mA Exceeding maximum ratings may shorten the useful life of the device. These user guidelines are not tested. Static Discharge Voltage............. ...............................>2001V (MIL-STD-883, Method 3015) Storage Temperature ................................. –65°C to +150°C Latch Up Current ..................................................... >200 mA Ambient Temperature with Power Applied ............................................ –55°C to +125°C Operating Range Supply Voltage on VCC Relative to GND [2] ....–0.5V to +4.6V Range VCC DC Voltage Applied to Outputs in High Z State [2] ................................... –0.5V to VCC + 0.5V Ambient Temperature Industrial –40°C to +85°C 3.3V ± 0.3V DC Input Voltage [2] ............................... –0.5V to VCC + 0.5V DC Electrical Characteristics Over the Operating Range Parameter Description Test Conditions VOH Output HIGH Voltage VCC = Min, IOH = –4.0 mA VOL Output LOW Voltage VCC = Min, IOL = 8.0 mA VIH Input HIGH Voltage [2] –10 Min Unit Max 2.4 V 0.4 V 2.0 VCC + 0.3 V –0.3 0.8 V VIL Input LOW Voltage IIX Input Leakage Current GND < VI < VCC –1 +1 µA IOZ Output Leakage Current GND < VOUT < VCC, Output disabled –1 +1 µA ICC VCC Operating Supply Current VCC = Max, f = fMAX = 1/tRC, IOUT = 0 mA CMOS levels 175 mA ISB1 Automatic CE Power Down Max VCC, CE1 > VIH, CE2 < VIL, Current — TTL Inputs VIN > VIH or VIN < VIL, f = fMAX 30 mA ISB2 Automatic CE Power Down Max VCC, CE1 > VCC – 0.3V, CE2 < 0.3V, Current —CMOS Inputs VIN > VCC – 0.3V, or VIN < 0.3V, f = 0 25 mA Note 2. VIL (min) = –2.0V and VIH(max) = VCC + 2V for pulse durations of less than 20 ns. Document Number: 38-05478 Rev. *D Page 3 of 10 CY7C1069DV33 Capacitance Tested initially and after any design or process changes that may affect these parameters. Description Test Conditions CIN Parameter Input Capacitance TA = 25°C, f = 1 MHz, VCC = 3.3V COUT IO Capacitance TSOP II VFBGA Unit 6 8 pF 8 10 pF TSOP II VFBGA Unit 24.18 28.37 °C/W 5.40 5.79 °C/W Thermal Resistance Tested initially and after any design or process changes that may affect these parameters. Parameter Description Test Conditions ΘJA Thermal Resistance (Junction to Ambient) ΘJC Thermal Resistance (Junction to Case) Still air, soldered on a 3 × 4.5 inch, four layer printed circuit board AC Test Loads and Waveforms The AC test loads and waveform diagram follows. [3] High-Z characteristics 3.3V 50Ω VTH = 1.5V OUTPUT Z0 = 50Ω R1 317Ω OUTPUT 30 pF* 5 pF* (a) * Capacitive load consists of all components of the test environment 3.0V GND Rise Time > 1 V/ns ALL INPUT PULSES 90% 90% 10% 10% (c) R2 351Ω INCLUDING JIG AND SCOPE (b) Fall Time: > 1 V/ns Note 3. Valid SRAM operation does not occur until the power supplies have reached the minimum operating VDD (3.0V). 100 µs (tpower) after reaching the minimum operating VDD, normal SRAM operation begins including reduction in VDD to the data retention (VCCDR, 2.0V) voltage. Document Number: 38-05478 Rev. *D Page 4 of 10 CY7C1069DV33 AC Switching Characteristics Over the Operating Range [4] Parameter –10 Description Min Max Unit Read Cycle tpower VCC(Typical) to the First Access [5] 100 µs tRC Read Cycle Time 10 ns tAA Address to Data Valid tOHA Data Hold from Address Change tACE CE1 LOW/CE2 HIGH to Data Valid 10 ns tDOE OE LOW to Data Valid 5 ns tLZOE OE LOW to Low Z 10 tHZOE OE HIGH to High Z CE1 LOW/CE2 HIGH to Low Z [6] tHZCE [6] tPD ns 1 [6] tLZCE tPU 3 CE1 HIGH/CE2 LOW to High Z ns 5 CE1 LOW/CE2 HIGH to Power Up 3 CE1 HIGH/CE2 LOW to Power Down 0 [7] ns ns 5 [7] ns ns ns 10 ns Write Cycle [8, 9] tWC Write Cycle Time 10 ns tSCE CE1 LOW/CE2 HIGH to Write End 7 ns tAW Address Setup to Write End 7 ns tHA Address Hold from Write End 0 ns tSA Address Setup to Write Start 0 ns tPWE WE Pulse Width 7 ns tSD Data Setup to Write End 5.5 ns tHD Data Hold from Write End 0 ns 3 ns tLZWE tHZWE WE HIGH to Low Z [6] WE LOW to High Z [6] 5 ns Notes 4. Test conditions assume signal transition time of 3 ns or less, timing reference levels of 1.5V, and input pulse levels of 0 to 3.0V. Test conditions for the read cycle use output loading shown in part a) of AC Test Loads and Waveforms, unless specified otherwise. 5. tPOWER gives the minimum amount of time that the power supply is at typical VCC values until the first memory access is performed. 6. tHZOE, tHZCE, tHZWE, tLZOE, tLZCE, and tLZWE are specified with a load capacitance of 5 pF as in (b) of AC Test Loads and Waveforms. Transition is measured ±200 mV from steady state voltage. 7. These parameters are guaranteed by design and are not tested. 8. The internal write time of the memory is defined by the overlap of WE, CE1 = VIL, and CE2 = VIH. CE1 and WE are LOW along with CE2 HIGH to initiate a write, and the transition of any of these signals can terminate. The input data setup and hold timing should be referenced to the edge of the signal that terminates the write. 9. The minimum write cycle time for Write Cycle No. 2 (WE controlled, OE LOW) is the sum of tHZWE and tSD. Document Number: 38-05478 Rev. *D Page 5 of 10 CY7C1069DV33 Data Retention Characteristics Over the Operating Range Parameter Description Conditions VDR VCC for Data Retention ICCDR Data Retention Current tCDR [10] Chip Deselect to Data Retention Time tR [ 11] Min Typ Max Unit 2 V 25 VCC = 2V , CE1 > VCC – 0.2V, CE2 < 0.2V, VIN > VCC – 0.2V or VIN < 0.2V Operation Recovery Time mA 0 ns tRC ns Data Retention Waveform DATA RETENTION MODE VCC 3.0V 3.0V VDR > 2V tR tCDR CE Switching Waveforms Figure 3. Read Cycle No. 1 [12, 13] tRC RC ADDRESS tOHA DATA OUT tAA PREVIOUS DATA VALID DATA VALID Figure 4. Read Cycle No. 2 (OE Controlled) [13, 15] ADDRESS tRC CE1 CE2 tACE OE tHZOE tDOE tHZCE tLZOE DATA OUT HIGH IMPEDANCE DATA VALID tLZCE VCC SUPPLY CURRENT HIGH IMPEDANCE tPD tPU 50% 50% ICC ISB Notes 10. Tested initially and after any design or process changes that may affect these parameters. 11. Full device operation requires linear VCC ramp from VDR to VCC(min.) > 50 µs or stable at VCC(min.) > 50 µs. 12. The device is continuously selected. CE1 = VIL, and CE2 = VIH. 13. WE is HIGH for read cycle. 14. Address valid before or similar to CE1 transition LOW and CE2 transition HIGH. Document Number: 38-05478 Rev. *D Page 6 of 10 CY7C1069DV33 Switching Waveforms (continued) Figure 5. Write Cycle No. 1 (CE Controlled) [15, 16, 17] tWC ADDRESS tSA CE tSCE tAW tHA tPWE WE tSD tHD DATA IO Figure 6. Write Cycle No. 2 (WE Controlled, OE LOW) [15, 16, 17] tWC ADDRESS tSCE CE tAW tHA tSA tPWE WE tHZWE tSD tHD DATA IO tLZWE Notes 15. CE is a shorthand combination of both CE1 and CE2 combined. It is active LOW. 16. Data IO is high impedance if OE = VIH. 17. If CE goes HIGH simultaneously with WE going HIGH, the output remains in a high impedance state. Document Number: 38-05478 Rev. *D Page 7 of 10 CY7C1069DV33 Truth Table CE1 CE2 OE WE IO0 – IO7 Mode Power H X X X High Z Power Down Standby (ISB) X L X X High Z Power Down Standby (ISB) L H L H Data Out Read All Bits Active (ICC) L H X L Data In Write All Bits Active (ICC) L H H H High Z Selected, Outputs Disabled Active (ICC) Ordering Information Speed (ns) 10 Ordering Code Package Diagram Package Type CY7C1069DV33-10ZSXI 51-85160 54-Pin TSOP II (Pb-Free) CY7C1069DV33-10BVXI 51-85178 48-Ball VFBGA (8 × 9.5 × 1 mm) (Pb-Free) Operating Range Industrial Package Diagrams Figure 7. 54-Pin TSOP Type II 51-85160-** Document Number: 38-05478 Rev. *D Page 8 of 10 CY7C1069DV33 Package Diagrams (continued) Figure 8. 48-Ball VFBGA (8 x 9.5 x 1 mm) BOTTOM VIEW TOP VIEW A1 CORNER C Ø0.05 M Ø0.25 M C A B A1 CORNER Ø0.30±0.05(48X) 3 4 5 6 6 5 4 3 2 1 A B C B F G D E 2.625 E C 0.75 D 5.25 A 9.50±0.10 9.50±0.10 1 2 F G H H A 1.875 A B 8.00±0.10 0.75 B 0.10 C 0.21±0.05 0.25 C 0.55 MAX. 3.75 8.00±0.10 0.15(4X) Document Number: 38-05478 Rev. *D 1.00 MAX 0.26 MAX. SEATING PLANE C 51-85178. ** Page 9 of 10 CY7C1069DV33 Document History Page Document Title: CY7C1069DV33 16-Mbit (2M x 8) Static RAM Document Number: 38-05478 REV. ECN NO. Issue Date Orig. of Change Description of Change ** 201560 See ECN SWI Advance datasheet for C9 IPP *A 233748 See ECN RKF Modified AC, DC parameters as per EROS (Specification 01-2165) Pb-free Offering in the Ordering Information *B 469420 See ECN NXR Converted from Advance Information to Preliminary Removed –8 and –12 speed bins from product offering Removed Commercial Operating Range Changed 2G Ball of FBGA and pin 40 of TSOPII from DNU to NC Included the Maximum ratings for Static Discharge Voltage and Latch Up Current on page 3 Changed ICC(Max) from 220 mA to 100 mA Changed ISB1(Max) from 70 mA to 30 mA Changed ISB2(Max) from 40 mA to 25 mA Specified the Overshoot specification in footnote 1 Added Data Retention Characteristics table on page 5 Updated the 48-pin FBGA package Updated the Ordering Information table. *C 499604 See ECN NXR Added note 1 for NC pins Updated Test Condition for ICC in DC Electrical Characteristics table Updated the 48-Ball FBGA Package *D 1462585 See ECN VKN/AESA Converted from preliminary to final Changed ICC spec from 125 mA to 175 mA Updated thermal specs © Cypress Semiconductor Corporation, 2004-2007. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 38-05478 Rev. *D Revised September 06, 2007 All product and company names mentioned in this document are the trademarks of their respective holders. Page 10 of 10