NIMD6001 Dual N-Channel Driver with Diagnostic Output 60 V, 3 A, 110 mW NIMD6001 is a dual 3 Amp low-side switch with an integrated common disable input and drain diagnostic output. Pulling the Disable pin low will override any applied gate voltages and turn off both FET switches. Should either Drain-Source voltage exceed approximately 50 V, a logic 1 (> 3 V) will be asserted on the Diagnostic/Feedback pin. Internal isolation diodes permit the Disable and Diagnostic/ Feedback pins of multiple devices to be interconnected in a “wired-OR” configuration without additional components. http://onsemi.com 3.0 AMPERES 60 VOLTS RDS(on) = 110 mW SOIC−8 CASE 751 PLASTIC Features RDSON 110 mW Maximum at VGS = 10 V Avalanche Energy Specified Gate Drive Disable Input Drain-Source Voltage Diagnostic Feedback Output Electrically Isolated Drains for Low Crosstalk Internal Resistors Limit Peak Transient gate Current AEC-Q101 Qualified This is a Pb−Free Device MARKING DIAGRAM Source 1 Gate 1 Source 2 Gate 2 1 8 2 7 3 4 D6001 AYWWG G • • • • • • • • 6 5 Drain 1 Disable Drain 2 Diag/Fbk (Top View) D6001 = Specific Device Code A = Assembly Location Y = Year WW = Work Week G = Pb−Free Package (Note: Microdot may be in either location) Applications • Automotive Injector Driver • Solenoid / Relay Driver MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Rating Symbol Value Unit Drain−to−Source Voltage (DC, sustained) VDSS 60 Vdc Gate−to−Source Voltage VGS "20 Vdc Continuous Drain Current VGS = 10 V, RqJA = 55°C/W VGS = 5.0 V, RqJA = 55°C/W Single Pulse Drain Current Pulse duration = 80 ms Single Pulse Drain-to-Source Avalanche Energy VDD = 60 V; VGS = 10 V; IPK = 2.6 A; L = 42 mH; Start Tj = 25°C Operating Junction Temperature Storage Temperature ID 3.3 3.0 1 8 A 2 7 3 6 4 5 ID 10 A EAS 150 mJ TJ −55 − 150 °C TSTG −55 − 150 °C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. INTERNAL DIAGRAM ORDERING INFORMATION Device Package Shipping NIMD6001NR2G SOIC−8 (Pb−Free) 2500/Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. © Semiconductor Components Industries, LLC, 2009 September, 2009 − Rev. 4 1 Publication Order Number: NIMD6001N/D NIMD6001 PIN DESCRIPTIONS Pin # Symbol 1 S1 FET 1 Source and Body 2 G1 FET 1 Gate 3 S2 FET 2 Source and Body 4 G2 FET 2 Gate 5 Diag/Fbk 6 D2 7 Disable 8 D1 Description Diagnostic Feedback − This pin will be logic high when either FET Drain-Source voltage exceeds the Drain Diagnostic threshold. FET 2 Drain Gate Disable − Pull this pin low to disable both FETs. A logic low will override voltage applied to G1 or G2. FET 1 Drain THERMAL RESISTANCE Parameter Symbol Value Units Junction-to-Ambient − min. pad footprint (Notes 1 and 2) RqJA 96 °C/W Junction-to-Ambient − 1″ Cu pad (Notes 1 and 3) RqJA 75 ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise specified) Parameter Symbol Test Condition Min Typ V(BR)DSS VGS = 0 V; ID = 5 mA 60 67 Zero Gate Voltage Drain Current (Note 1) IDSS VGS = 0 V; VDS = 15 V VGS = 0 V; VDS = 15 V; TA = 150°C Gate Input Current IGSS VGS = ±20 V; VDS = 0 V Max Units OFF CHARACTERISTICS Drain-to-Source Breakdown Voltage V 10 80 20 250 mA −100 ±25 +100 nA 1.0 ON CHARACTERISTICS Gate Threshold Voltage VGS(TH) VDS = VGS; ID = 250 mA 1.7 3.0 Static Drain-to-Source On-Resistance RDS(ON) VGS = 10 V; ID = 3.3 A 60 110 mW Static Drain-to-Source On-Resistance RDS(ON) VGS = 5 V; ID = 3.0 A 72 130 mW 150 175 pF 150 170 25 30 8 15 kW 8.3 9.0 nC 1.1 1.6 4.2 5 DYNAMIC CHARACTERISTICS (Note 1) Input Capacitance CISS Output Capacitance COSS Reverse Transfer Capacitance CRSS Gate Resistance Total Gate Charge RG Qg(TOT) Gate-to-Source Gate Charge Qgs Gate-to-Drain Miller Charge Qgd 1. 2. 3. 4. VGS = 0 V; VDS = 15 V; f = 75 kHz VGS = 0 V to 5 V; VDD = 30 V; ID = 3.3 A; IG = 1.0 mA, These values are established by statistical characterization and may not be tested. Surface-mounted on FR4 board using the minimum recommended pad size (Cu area = 40 sq. mm; 1 oz.) Surface-mounted on FR4 board using 1 sq. inch heat spreader (Cu area = 625 sq. mm, 2 oz.) Refer to Figure 1 for definition of switching characteristics symbols. http://onsemi.com 2 NIMD6001 ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise specified) Parameter Symbol Test Condition Min Typ Max Units 6.0 8.0 ms SWITCHING CHARACTERISTICS (Notes 1 and 4) Turn-On Time T(on) Turn-On Delay Td(on) Rise Time Tr 1.7 VGS = 10 V; VDD = 30 V; ID = 3.3 A, Ext. RGS = 47 W 3.9 Turn-Off Time T(off) 24 Turn-Off Delay Td(off) 15 Tf 9.0 Fall Time 28 BODY DIODE VSD VGS = 0 V, ISD = 3.3 A 1.25 V VFBK VDS = 35 V, RFBK-SOURCE = 51 kW 1.7 V VFBK(HI) VDS = 60 V, RFBK-SOURCE = 51 kW 3.0 5.5 V VDS threshold voltage for logical High VDSFBK(HI) Ramp VDS positive until VFBK = 3.5 V 45 65 V VDS threshold voltage for logical Low VDSFBK(LOW) Ramp VDS negative until VFBK = 0.8 V 25 45 V Gate Drive Disable Input Voltage, Gate Enable VDIS(HI) VDIS ≥ 3.0 V, VGS = 5 V, ID = 3.0 A 3 Gate Drive Disable Input Voltage, Gate Disable VDIS(LOW) VDIS ≤ 0.4 V, VGS = VDS = 10 V, ID ≤ 250 mA; Tj = 150°C (Note 1) Source-Drain Forward On Voltage 0.85 DIAGNOSTIC FEEDBACK (Note 1) Feedback voltage Feedback Logical High voltage DISABLE (Note 1) 1. 2. 3. 4. These values are established by statistical characterization and may not be tested. Surface-mounted on FR4 board using the minimum recommended pad size (Cu area = 40 sq. mm; 1 oz.) Surface-mounted on FR4 board using 1 sq. inch heat spreader (Cu area = 625 sq. mm, 2 oz.) Refer to Figure 1 for definition of switching characteristics symbols. Figure 1. Switching Characteristics Waveforms and Symbols http://onsemi.com 3 V 0.4 V NIMD6001 TYPICAL ELECTRICAL CHARACTERISTICS 7 10 5 4 3.0 V 3 2 1 RDS(on), DRAIN−SOURCE RESISTANCE (W) 0 8 TJ = 125°C 6 TJ = 25°C 4 2 TJ = −40°C 2.5 V 0 0.5 1.0 1.5 0 2.0 1.5 3.0 3.5 4.0 Figure 2. Drain Current vs. Drain−Source Voltage and Gate−Source Voltage Figure 3. Transfer Function (pulsed). Pulse duration = 80 ms, duty cycle < 0.5%; VDS = 2 V 100 VGS = 5 V, ID = 3 A 80 VGS = 10 V, ID = 3.3 A 60 40 20 0 −40 −20 0 20 40 60 80 100 120 140 TJ, JUNCTION TEMPERATURE (°C) 1.0 0.9 0.8 IS = 3 A 0.7 0.6 −40 −20 0 20 40 60 80 100 120 140 TJ, JUNCTION TEMPERATURE (°C) Figure 4. Drain−Source On Resistance vs. Junction Temperature Figure 5. Body Diode Forward Voltage vs. Junction Temperature 5 2.5 VFBK, DIAGNOSTIC/FEEDBACK VOLTAGE (V) 3.0 ID, DRAIN CURRENT (mA) 2.5 VGS, GATE−SOURCE VOLTAGE (V) 120 TJ = 25°C 2.0 1.5 1.0 0.5 0 2.0 VDS, DRAIN−SOURCE VOLTAGE (V) VSD, SOURCE−DRAIN FORWARD VOLTAGE (V) ID, DRAIN CURRENT (A) 6 ID, DRAIN−CURRENT (A) VGS = 3.5 V 0 10 20 30 40 50 60 4 3 2 1 0 70 TJ = 25°C 0 10 20 30 40 50 60 VDS, DRAIN−SOURCE VOLTAGE (V) VDS, DRAIN−SOURCE VOLTAGE (V) Figure 6. Off−State Drain Current vs. Drain−Source Voltage (includes feedback network current) Figure 7. Diagnostic Feedback Voltage vs. Drain−Source Voltage http://onsemi.com 4 70 NIMD6001 PEAK CURRENT (A) ENERGY (mJ) 1000 100 10 1 1 10 LOAD INDUCTANCE (mH) Figure 8. Single Pulse Peak Drain Current and Avalanche Energy Capability vs. Load Inductance Figure 9. Single Pulse Peak Drain Current and Avalanche Energy Test Circuit http://onsemi.com 5 100 NIMD6001 TYPICAL THERMAL RESPONSE CHARACTERISTICS RqJA, PEAK JUNCTION THERMAL TRANSIENT RESPONSE (°C/W) 1000 100 D = 0.8 0.5 10 0.2 0.1 1 0.04 0.02 0.01 0.1 SINGLE PULSE 0.0001 0.00001 0.001 0.01 0.1 ON−TIME PULSE WIDTH (s) 1 10 100 1000 100 1000 100 1000 Figure 10. Single Channel Active; Mounted on Minimum−Pad Board RqJA, PEAK JUNCTION THERMAL TRANSIENT RESPONSE (°C/W) 1000 100 10 1 0.1 D = 0.8 0.5 0.2 0.1 0.04 0.02 0.01 SINGLE PULSE 0.00001 0.0001 0.001 0.1 0.01 ON−TIME PULSE WIDTH (s) 1 10 Figure 11. Single Channel Active; Mounted on 1 Sq. Inch Copper Spreader RqJA, PEAK JUNCTION THERMAL TRANSIENT RESPONSE (°C/W) 1000 100 D = 0.8 0.5 0.2 0.1 10 0.04 0.02 0.01 1 0.1 SINGLE PULSE 0.00001 0.0001 0.001 0.01 0.1 ON−TIME PULSE WIDTH (s) 1 10 Figure 12. Both Channels Active; Mounted on Minimum−Pad Board http://onsemi.com 6 NIMD6001 TYPICAL THERMAL RESPONSE CHARACTERISTICS RqJA, PEAK JUNCTION THERMAL TRANSIENT RESPONSE (°C/W) 1000 100 10 1 0.1 D = 0.8 0.5 0.2 0.1 0.04 0.02 0.01 SINGLE PULSE 0.00001 0.0001 0.001 0.01 0.1 ON−TIME PULSE WIDTH (s) 1 10 100 1000 100 1000 100 1000 Figure 13. Both Channels Active; Mounted on 1 Sq. Inch Copper Spreader RqJA, PEAK JUNCTION THERMAL TRANSIENT RESPONSE (°C/W) 1000 100 D = 0.8 0.5 0.2 0.1 10 0.04 0.02 0.01 1 0.1 SINGLE PULSE 0.00001 0.0001 0.001 0.1 0.01 ON−TIME PULSE WIDTH (s) 1 10 Figure 14. Channels Alternatively Active; Mounted on Minimum−Pad Board RqJA, PEAK JUNCTION THERMAL TRANSIENT RESPONSE (°C/W) 1000 100 10 1 0.1 D = 0.8 0.5 0.2 0.1 0.04 0.02 0.01 SINGLE PULSE 0.00001 0.0001 0.001 0.01 0.1 ON−TIME PULSE WIDTH (s) 1 10 Figure 15. Channels Alternatively Active; Mounted on 1 Sq. Inch Copper Spreader http://onsemi.com 7 NIMD6001 TYPICAL APPLICATION CIRCUIT C1 C2 C3 C4 +VDD FBK D1 S1 Injector 1 Disable G1 D2 S2 Injector 4 U1 G2 C1 Diag NIMD6001 S1 D1 Injector 2 C4 C2 C3 Disable G1 CONTROLLER FBK D2 S2 Injector 3 U2 G2 Diag NIMD6001 Master Disable Figure 16. 4 Cylinder Engine Fuel Injection • 4-Cycle engine; 1 injector pulse during intake stroke • To optimize transient thermal resistance of the • Cylinder firing order is 1-3-4-2 • The coincident FBK pulse will be missing if any NIMD6001 devices, the injector drive pulses are alternated between U1 and U2. injector is open or shorted. http://onsemi.com 8 NIMD6001 PACKAGE DIMENSIONS SOIC−8 NB CASE 751−07 ISSUE AJ −X− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. A 8 5 S B 0.25 (0.010) M Y M 1 4 −Y− K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE −Z− 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 9 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NIMD6001N/D