1N5391 THRU 1N5399 GENERAL PURPOSE PLASTIC RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 1.5 Amperes FEATURES DO-204AL ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High surge current capability ♦ 1.5 Ampere operation at TL=70°C with no thermal runaway ♦ Low reverse leakage ♦ Construction utilizes void-free molded plastic technique ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) DIA. 0.205 (5.2) 0.160 (4.1) MECHANICAL DATA Case: JEDEC DO-204AL molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram 1.0 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) DIA. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N 5391 1N 5392 1N 5393 1N 5394 1N 5395 1N 5396 1N 5397 1N 1N 5398 5399 *Maximum repetitive peak reverse voltage VRRM 50 100 200 300 400 500 600 800 1000 Volts *Maximum RMS voltage VRMS 35 70 140 210 280 350 420 560 700 Volts *Maximum DC blocking voltage VDC 50 100 200 300 400 500 600 800 1000 Volts *Maximum average forward rectified current 0.500” (12.7mm) lead length at TL=70°C I(AV) 1.5 Amps *Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at TA=75°C IFSM 50.0 Amps *Maximum instantaneous forward voltage at 1.5A TA=70°C VF 1.4 Volts *Maximum DC reverse current at rated DC blocking voltage IR 5.0 300.0 µA IR(AV) 300.0 µA Typical reverse recovery time (NOTE 1) trr 2.0 µs Typical junction capacitance (NOTE 2) CJ 15.0 pF RΘJA RΘJL 50.0 25.0 °C/W TA +150 °C TJ -50 to + 170 °C TSTG -50 to+175 °C TA=25°C TA=150°C *Maximum full load reverse current full cycle average, 0.375",(9.5mm) lead length at TL=70°C Typical thermal resistance (NOTE 3) *Maximum DC blocking voltage temperature *Operating junction temperature range *Storage temperature range NOTES: (1) Measured with IF=0.5A, IR=0.1A, Irr= 0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient and from junction to lead at 0.375” (9.5mm) lead length, P.C.B. mounted *JEDEC registered value 4/98 UNITS RATINGS AND CHARACTERISTIC CURVES 1N5391 THRU 1N5399 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 2.4 2.0 50 60 HZ RESISTIVE OR INDUCTIVE LOAD 0.50” (12.7mm) LEAD LENGTH PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE 1.6 0.2 x 0.2” (5.0 x 5.0mm) COPPER PADS 1.2 0.8 5 10 Ipk/IAV = 20 0.4 CAPACITIVE LOADS 0 25 50 75 100 125 150 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) TA=75°C 40 30 20 10 175 0 LEAD TEMPERATURE, °C 10 1 100 NUMBER OF CYCLES AT 60HZ FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 1,000 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 100 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 0.01 0.6 0.8 1.0 1.2 1.4 1.6 100 TJ=150°C 10 1 0.1 TJ=25°C 0.01 0 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE TJ=25°C f=1.0 MHz Vsig=50mVp-p TRANSIENT THERMAL IMPEDANCE, °C/W JUNCTION CAPACITANCE, pF 100 10 1 0.1 1 10 REVERSE VOLTAGE, VOLTS 100 100 10 1 0.1 0.01 0.1 1 t, PULSE DURATION, sec. 10 100