1N5391GP THRU 1N5399GP GLASS PASSIVATED JUNCTION RECTIFIER * Reverse Voltage - 50 to 1000 Volts FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ 1.5 Ampere operation at TA=70°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ High temperature soldering guaranteed: 350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension T E D DO-204AC 0.034 (0.86) N E P A T Forward Current - 1.5 Amperes 0.028 (0.71) DIA. 1.0 (25.4) MIN. 0.300 (7.6) 0.230 (5.8) 0.140 (3.6) 0.104 (2.6) DIA. 1.0 (25.4) MIN. Dimensions in inches and (millimeters) *Glass-plastic encapsulation technique is covered by Patent No. 3,996,602 and brazed-lead assembly by Patent No. 3,930,306 ® MECHANICAL DATA Case: JEDEC DO-204AC molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.015 ounce, 0.4 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N53 91GP 1N53 92GP 1N53 93GP 1N53 94GP 1N53 95GP 1N53 96GP 1N53 97GP 1N53 98GP 1N53 99GP UNITS * Maximum repetitive peak reverse voltage VRRM 50 100 200 300 400 500 600 800 1000 Volts * Maximum RMS voltage VRMS 35 70 140 210 280 350 420 560 700 Volts * Maximum DC blocking voltage VDC 50 100 200 300 400 500 600 800 1000 Volts * Maximum average forward rectified current 0.375" (9.5mm) lead length at TL=70°C I(AV) 1.5 Amps * Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 50.0 Amps * Maximum instantaneous forward voltage at 1.5A, TA=70°C VF 1.4 Volts *Maximum DC reverse current at rated DC blocking voltage IR 5.0 300.0 µA IR(AV) 300.0 µA trr 2.0 µs CJ 15.0 pF RΘJA 45.0 °C/W TA=25°C TA=150°C * Maximum full load reverse current full cycle average, 0 375" (9.5mm) lead length at TA=70°C Typical reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) *Operating junction and storage temperature range TJ, TSTG NOTES: (1) Reverse recovery test condition: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B. mounted * JEDEC registered values 4/98 -65 to +175 °C RATINGS AND CHARACTERISTIC CURVES 1N5391GP THRU 1N5399GP FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE 2.0 50 PEAK FORWARD SURGE CURRENT, AMPERES TL, LEAD TEMPERATURE 60 HZ RESISTIVE OR INDUCTIVE LOAD 1.0 TA, AMBIENT TEMPERATURE 0.5 0.375" (9.5mm) LEAD LENGTH 0 25 0 50 75 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 40 30 20 10 100 125 150 175 0 TEMPERATURE, °C 10 1 100 NUMBER OF CYCLES AT 60 HZ FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 1 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 10 TJ=125°C 1 TJ=75°C 0.1 TJ=25°C 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE (°C/W) FIG. 5 - TYPICAL JUNCTION CAPACITANCE 100 JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 100 10 1 0.1 0.01 0.1 1 t, PULSE DURATION, sec 1 1 10 REVERSE VOLTAGE, VOLTS 100 10 100