GI500 THRU GI510 GENERAL PURPOSE PLASTIC RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 3.0 Amperes FEATURES DO-201AD ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High surge current capability ♦ Typical IR less than 0.1µA ♦ Construction utilizes void-free molded plastic technique ♦ High current operation of 3.0 Amperes at TA=95°C with no thermal runaway ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.210 (5.3) 0.190 (4.8) DIA. 0.375 (9.5) 0.285 (7.2) MECHANICAL DATA 0.052 (1.32) 0.048 (1.22) DIA. 1.0 (25.4) MIN. Case: JEDEC DO-201AD molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.04 ounce, 1.1 grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GI 500 GI 501 GI 502 GI 504 GI 506 GI 508 GI 510 UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current 0.375" (9.5mm) lead length at TA= 95°C I(AV) 3.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 100.0 Amps Maximum instantaneous forward voltage TJ= 25°C at 9.4A TJ=175°C VF 1.1 1.0 Volts Maximum DC reverse current at rated DC blocking voltage IR 5.0 50.0 µA Typical junction capacitance (NOTE 1) CJ 28.0 pF Typical reverse recovery time (NOTE 2) trr 2.0 µs RΘJA RΘJL 20.0 5.0 °C/W TJ -50 to +150 °C TSTG -50 to +175 °C Typical thermal resistance (NOTE 3) Operating junction temperature range Storage temperature range TA=25°C TA=100°C NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (3) Thermal resistance from junction to ambient and from junction to lead at 0.375” (9.5mm) lead length, P.C.B. mounted with 0.8 x 0.8” (20 x 20mm) copper heatsinks 4/98 8.0 L=0.25” (6.3mm) 200 TL = BOTH LEADS to HEAT SINK MOUNTED LENGTHS (L) as SHOWN L= 0.50” (12.7mm) 5.0 60HZ RESISTIVE OR INDUCTIVE LOAD 4.0 3.0 2.0 1.0 TJ=150°C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) L = 0.31”(7.9mm) 7.0 6.0 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG. 1 - FORWARD CURRENT DERATING CURVE PEAK FORWARD CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES RATINGS AND CHARACTERISTIC CURVES GI500 THRU GI510 TA=AMBIENT TEMPERATURE 0.375 (9.5mm) LEAD LENGTH P.C.B. MOUNTING 0 20 40 60 80 100 REPETITIVE 10 100 120 140 NON-REPETITIVE 160 1 10 NUMBER OF CYCLES AT 60 HZ TEMPERATURE, °C FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 100 100 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 100 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 10 1 0.1 10 TJ=150°C 1 TJ=100°C 0.1 TJ=25°C 0.01 0 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE,% 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE JUNCTION CAPACITANCE, pF 100 TJ=25°C f=1.0 MHz Vsig=50mVp-p 10 1 0.1 1 10 REVERSE VOLTAGE, VOLTS 100 TRANSIENT THERMAL IMPEDANCE, °C/W 100 FIG. 5 - TYPICAL JUNCTION CAPACITANCE 10 1 0.1 0.01 0.1 1 t, PULSE DURATION, sec. 10 100