THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS CW 0644 FPLD54TE1 622.08M 3.3V SURFACE MOUNT CLOCK OSCILLATOR FPLD54TE1 ABSOLUTE MAXIMUM RATINGS PARAMETER TABLE 1.0 UNITS MINIMUM NOMINAL MAXIMUM UNITS -40 - 85 °C Storage Temperature Supply Voltage (Vcc) -0.5 - 7.0 Vdc Enable/Disable Voltage (Vc) -0.5 - Vcc+0.5 Vdc OPERATING SPECIFICATIONS NOTE DESCRIPTION TABLE 2.0 PARAMETER MINIMUM Center Frequency (Fo) Total Frequency Tolerance Operating Temperature Range MAXIMUM UNITS - NOMINAL 622.08000 644.53125 666.51430 669.32660 672.16270 - MHz -20 - 20 ppm 0 - 70 °C Vdc Supply Voltage (Vcc) 3.135 3.3 3.465 Supply Current (Icc) - - 100 mA Jitter (BW=10Hz to 20MHz) - - 5 ps rms Jitter (BW=12kHz to 80MHz) - - 1 ps rms SSB Phase Noise at 100Hz offset - -60 - dBc/Hz SSB Phase Noise at 1KHz offset - -90 - dBc/Hz SSB Phase Noise at 10KHz offset - -130 - dBc/Hz SSB Phase Noise at 100KHz offset - -135 - dBc/Hz NOTE 1 The Connor-Winfield FPLD54TE1 is a 3.3V Clock Oscillator with Differential LVPECL outputs and Enable/Disable function. The FPLD54TE1 is designed for use with PLL systems in SONET/SDH systems requiring low jitter and tight frequency stability. No PLL multiplication schemes are used in this oscillator design. FEATURES INPUT CHARACTERISTICS TABLE 3.0 PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE Enable Input Voltage (Low) (Default) (Vil) - 1.68 Vdc 2 Disable Input Voltage (High) (Vih) 2.275 - - Vdc 2 3.3V OPERATION LOW VOLTAGE PECL OUTPUT CHARACTERISTICS PARAMETER Voltage TABLE 4.0 MINIMUM NOMINAL MAXIMUM UNITS NOTE - - 50 Ohms 3 LOAD (High) (Voh) 2.275 - - Vdc (Low) (Vol) - - 1.68 Vdc 45 50 55 % - - 1 nS Duty Cycle at 50% Level Rise / Fall Time 20% to 80% LOW PROFILE, SURFACE MOUNT PACKAGE LOW JITTER <1pS RMS TOTAL FREQUENCY TOLERANCE ±20ppm TEMPERATURE RANGE 0 to 70°C DIFFERENTIAL LVPECL OUTPUTS PACKAGE CHARACTERISTICS Package TABLE 5.0 Non-hermetic package consisting of an FR4 substrate with grounded metal cover. PROCESS RECOMMENDATIONS 2.0 3.0 RoHS 5/6 COMPLIANT TABLE 6.0 Soldering Process Wash Notes 1.0 ENABLE / DISABLE FUNCTION See solder profile on page 2. Ultrasonic cleaning is not recommended. ORDERING INFORMATION Inclusive of calibration @ 25°C, frequency stability vs. temperature, supply and load variations, shock, vibration and aging for twenty years. Control voltage (Vc) = 1.65 Vdc. When oscillator is disabled the true output is in a low state (Vol) and the complementary output is in the high state (VoH). Outputs are enabled with no connection on enable pad. 50 ohm termination into Vcc-2V or Thevein equivalent. FPLD54TE1 - 622.08M LVPECL CLOCK SERIES CENTER FREQUENCY Specifications subject to change without notice. DATA SHEET #: Ec165 PAGE 1 OF 2 REV: 07 DATE: 02/14/08 aCopyright 2008 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS Package Outline Pad Connections .140 MAX (3.56mm) N/C CW FPLD54TE1 622.08M ENABLE / DISABLE Dimensional Tolerance: ±.005 (.127mm) Suggested Pad Layout Output Waveform Test Circuit Solder Profile Temperature 225°C Ramp-Up Rate 3°C/second max. from 150°C to 225°C. 225°C tp Ramp-Down Rate 6°C/second max. 183°C 150°C 100°C 2 25°C N/C 0 E/D Time 60-120s Max. Vcc =Vcc2 =3.3Vdc 10-30s 60-150s Max. 360 Sec. Max. Specifications subject to change without notice. DATA SHEET #: Ec165 PAGE 2 OF 2 REV: 07 DATE: 02/14/08 aCopyright 2008 Connor-Winfield all rights reserved.