THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D AT A SHEET CRYSTAL CONTROLLED OSCILLATORS ABSOLUTE M AXIMUM RATING S PARAMETER MINIMUM NOMINAL MAXIMUM UNITS -55 - 125 °C Storage Temperature Supply Voltage (Vcc) -0.5 - 4.6 Vdc Input Voltage (Vcc) -0.5 - Vcc+0.5 Vdc MINIMUM NOMINAL MAXIMUM UNITS 200 - 800 MHz Total Frequency Tolerance -100 - 100 ppm Operating Temperature Range -40 - 85 °C Vdc OPERATING SPECIFIC ATIONS NOTE TABLE 2.0 PARAMETER (Fo) Supply Voltage (Vcc) 3.135 3.3 3.465 Supply Current (Icc) - - 60 mA Jitter (BW=10Hz to 20MHz) - - 10 ps rms Jitter (BW=12kHz to 80MHz) - - 3 ps rms SSB Phase Noise at 10Hz offset - -75 - dBc/Hz SSB Phase Noise at 100Hz offset - -95 - dBc/Hz SSB Phase Noise at 1KHz offset - -110 - dBc/Hz SSB Phase Noise at 10KHz offset - -125 - dBc/Hz SSB Phase Noise at 100KHz offset - -120 - dBc/Hz NOTE 1 MINIMUM NOMINAL MAXIMUM UNITS NOTE Disable Input Voltage (Low) (Vil) - 0.3Vcc Vdc 2 Enable Input Voltage (High) (Vih) 0.7Vcc - - Vdc 2 LVDS OUTPUT CHARACTERISTICS TABLE 4.0 PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE - - 100 Ohms 3 250 - 450 mV 45 50 55 % - 0.6 1.0 nS LOAD Output Differential Voltage (Vod) Duty Cycle at 50% Level Rise / Fall Time PACKAG E CHARACTERISTICS Package 4 TABLE 6.0 Soldering Process 3.3V OPERATION LVDS DIFFERENTIAL OUTPUTS ENABLE / DISABLE LOW JITTER <3pS RMS OVERALL FREQUENCY TOLERANCE ±100ppm TEMPERATURE RANGE: -40 to 85°C TABLE 5.0 Hermetically sealed ceramic package with grounded metal cover. PROCESS RECOMMENDATIONS 3.0 4.0 The Connor Winfield L753 is a Fixed Frequency, Surface Mount Crystal Controlled Oscillator (XO) designed for applications requiring low jitter and a ±100ppm, -40 to 85°C overall frequency tolerance, LVDS Differential Outputs and Tri-state Enable / Disable function. The L753 is designed using a 2X or 4X PLL multiplication to achieve the high output frequencies. TABLE 3.0 PARAMETER 2.0 DESCRIPTION FEATURES INPUT CHARACTERISTICS 1.0 L753 TABLE 1.0 UNITS Center Frequency CW 0643 L753 266.66M 3.3V LVDS 5x7.0mm CERAMIC SURFACE MOUNT HIGH FREQUENCY CLOCK OSCILLATOR See solder profile page 2. Notes Includes calibration @ 25°C, frequency stability vs. temperature, supply and load variations, shock, vibration and 20 years aging. When the oscillator is disabled, the outputs are at High Impedance. Output is enabled with no connection on pad 1. Vod measured with 100-ohm resistor between the true output and the complementary output. Duty Cycle measured at 50% of output swing. SURFACE MOUNT PACKAGE TAPE AND REEL PACKAGING RoHS COMPLIANT / LEAD FREE ORDERING INFORMATION L753 CLOCK SERIES - 266.66MHz CENTER FREQUENCY Specifications subject to change without notice. DATA SHEET #: Ds026 PAGE 1 OF 2 REV: 00 DATE: 11/03/06 aCopyright 2001 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D AT A SHEET CRYSTAL CONTROLLED OSCILLATORS Pin Connection Enable / Disable Function TABLE 7.0 Pin 1 2 3 4 5 6 Function Enable / Disable N/C Ground (Case) Output Q Comp Output Q Vcc Enable / Disable Function (Pad 1) High or Open Low Suggested Pad Layout Package Outline and Dimensions 7 TABLE 8.0 Output Enable Disable (High Impedance) MAX 0 MAX CW 0643 L753 266.66M .070 MAX (1.8mm) Output Waveform Test Circuit Solder Profile Temperature 260°C Q 260°C 220°C 180°C Vod 100 ohm 150°C 120°C 2 Q E/D 0 120 S Max. N/C 10 S Time 60 S Max. 360 Sec. Max. Specifications subject to change without notice. DATA SHEET #: Ds026 PAGE 1 OF 2 REV: 00 DATE: 11/03/06 aCopyright 2001 Connor-Winfield all rights reserved.