TI ISO1540DR

ISO1540
ISO1541
www.ti.com
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
Low-Power Bidirectional I2C Isolators
Check for Samples: ISO1540, ISO1541
•
•
•
•
•
•
Isolated Bidirectional, I C Compatible,
Communications
Supports up to 1 MHz Operation
3-V to 5.5-V Supply Range
Open Drain Outputs with 3.5-mA Side 1 and
35-mA Side 2 Sink Current Capability
-40°C to 125°C Operating Temperature
±50 kV/µs Transient Immunity (Typical)
HBM ESD Protection of 4 kV on All Pins;
8 kV on Bus Pins
APPLICATIONS
•
•
•
•
•
•
Isolated I2C Bus
SMBus and PMBus Interfaces
Open-drain Networks
Motor Control Systems
Battery Management
I2C Level Shifting
SAFETY AND REGULATORY
APPROVALS
•
•
•
•
4000-VPK Isolation per DIN EN 60747-5-2
(VDE 0884 Part 2) (Pending)
2500-VRMS Isolation for 1 minute per UL 1577
(Approved)
CSA Component Acceptance Notice 5A
(Approved)
IEC 60950-1 and IEC 61010-1 End Equipment
Standards (Approved)
ISO1540
VCC1 1
SDA1 2
SCL1 3
GND1 4
Side 1
Side 2
ISO1541
8 VCC2
VCC1 1
7 SDA2
SDA1 2
6 SCL2
SCL1 3
5 GND2
GND1 4
8 VCC2
Isolation
•
2
2
Isolation
FEATURES
1
7 SDA2
6 SCL2
5 GND2
Side 1
Side 2
DESCRIPTION
The ISO1540 and ISO1541 are low-power, bidirectional isolators that are compatible with I2C interfaces. These
devices have their logic input and output buffers separated by TI’s Capacitive Isolation technology using a silicon
dioxide (SiO2) barrier. When used in conjunction with isolated power supplies, these devices block high voltages,
isolate grounds, and prevent noise currents from entering the local ground and interfering with or damaging
sensitive circuitry.
This isolation technology provides for function, performance, size, and power consumption advantages when
compared to opto-couplers. The ISO1540 and ISO1541 enable a complete isolated I2C interface to be
implemented within a small form factor.
The ISO1540 has two isolated bidirectional channels for clock and data lines while the ISO1541 has a
bidirectional data and a unidirectional clock channel. The ISO1541 is useful in applications that have a single
Master while the ISO1540 is ideally fit for multi-master applications.
Isolated bidirectional communications is accomplished within these devices by offsetting the Side 1 Low-Level
Output Voltage to a value greater than the Side 1 High-Level Input Voltage thus preventing an internal logic latch
that otherwise would occur with standard digital isolators.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
I2C is a trademark of NXP B.V Corporation.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012, Texas Instruments Incorporated
ISO1540
ISO1541
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
PIN FUNCTIONS
ISO1540 and
ISO1541
I/O
NAME
PIN
VCC1
1
-
-
SDA1
2
I/O
I/O
SCL1
3
I/O
I
Serial Clock Input/Output, Side 1 Serial Clock Input, Side 1
GND1
4
-
-
Ground, Side 1
Ground, Side 1
GND2
5
-
-
Ground, Side 2
Ground, Side 2
SCL2
6
I/O
O
Serial Clock Input/Output, Side 2 Serial Clock Output, Side 2
SDA2
7
I/O
I/O
VCC2
8
-
-
DESCRIPTION
ISO1540
ISO1541
ISO1540
ISO1541
Supply Voltage, Side 1
Supply Voltage, Side 1
Serial Data, Side 1 Input/Output
Serial Data, Side 1 Input/Output
Serial Data Input/Output, Side 2
Serial Data Input/Output, Side 2
Supply Voltage, Side 2
Supply Voltage, Side 2
AVAILABLE OPTIONS
PRODUCT
RATED ISOLATION PACKAGE
ISO1540
4000-VPK and
2500-VRMS (1)
MARKED AS
Both SDA and SCL
are Bidirectional
IS1540
SDA is Bidirectional
SCL is Unidirectional
IS1541
ORDERING NUMBER
ISO1540D (rail)
ISO1540DR (reel)
D-8
ISO1541
(1)
CHANNEL DIRECTION
ISO1541D (rail)
ISO1541DR (reel)
See the Regulatory Information table for detailed Isolation specifications.
Table 1. FUNCTION TABLE (1)
(1)
(2)
2
POWER STATE
INPUT
OUTPUT
Z
VCC1 or VCC2 < 2.1 V
X
VCC1 and VCC2 > 2.8 V
L
L
VCC1 and VCC2 > 2.8 V
H
Z
VCC1 and VCC2 > 2.8 V
Z (2)
?
H = High Level; L = Low Level; Z = High Impedance or Float; X = Irrelevant; ? = Indeterminate
Invalid input condition as an I2C system requires that a pull-up resistor to VCC is connected.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
ISO1540
ISO1541
www.ti.com
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
ABSOLUTE MAXIMUM RATINGS
(1) (2)
VALUES
MIN
Supply voltage
Output current
Electrostatic
Discharge
VCC1, VCC2
–0.5
6
V
SDA1, SCL1
–0.5
VCC1 + 0.5
V
SDA2, SCL2
–0.5
VCC2 + 0.5
V
SDA1, SCL1
±20
mA
SDA2, SCL2
±100
mA
Bus Pins
±8
kV
All Pins
±4
Human Body Model
ESDA, JEDEC JS-001-2012
Field-Induced-Charged
Device Model
JEDEC JESD22-C101E
Machine Model
JEDEC JESD22-A115-A
TJ(MAX)
Maximum junction temperature
TSTG
Storage temperature range
(1)
(2)
UNIT
MAX
±1.5
All Pins
–65
kV
±200
V
150
°C
150
°C
Stresses beyond those listed under ABSOLUTE MAXIMUM RATINGS cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under RECOMMENDED
OPERATING CONDITIONS is not implied. Exposure to absolute-maximum-rated conditions for extended periods affects device
reliability.
All voltage values here within are with respect to the local ground terminal (GND1 or GND2) and are peak voltage values.
THERMAL INFORMATION
ISO1540
ISO1541
THERMAL METRIC (1)
UNITS
D (8 PINS)
θJA
Junction-to-ambient thermal resistance
114.6
θJCtop
Junction-to-case (top) thermal resistance
69.6
θJB
Junction-to-board thermal resistance
55.3
ψJT
Junction-to-top characterization parameter
27.2
ψJB
Junction-to-board characterization parameter
54.7
θJCbot
Junction-to-case (bottom) thermal resistance
n/a
(1)
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
RECOMMENDED OPERATING CONDITIONS
MIN
NOM
MAX
UNIT
VCC1, VCC2
Supply Voltage
3
5.5
VSDA1, VSCL1
Input/Output Signal Voltages, Side 1
0
VCC1
VSDA2, VSCL2
Input/Output Signal Voltages, Side 2
0
VCC2
VIL1
Low-Level Input Voltage, Side 1
0
0.5
VIH1
High-Level Input Voltage, Side 1
0.7 x VCC1
VCC1
VIL2
Low-Level Input Voltage, Side 2
0
0.3 x VCC2
VIH2
High-Level Input Voltage, Side 2
0.7 x VCC2
VCC2
IOL1
Output Current, Side 1
0.5
3.5
IOL2
Output Current, Side 2
0.5
35
Cb1
Maximum Capacitive Load, Side 1
40
Cb2
Maximum Capacitive Load, Side 2
400
fMAX
Maximum Operating Frequency
TA
Ambient Temperature
–40
125
°C
TJ
Junction Temperature
–40
136
°C
TSD
Thermal Shutdown
139
171
°C
(1)
V
mA
pF
(1)
1
MHz
This represents the maximum frequency with the maximum bus load (Cb) and the maximum current sink (IO). If the system has less bus
capacitance, then higher frequencies can be achieved.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
3
ISO1540
ISO1541
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
www.ti.com
ELECTRICAL CHARACTERISTICS
Over recommended operating conditions, unless otherwise noted
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
2.4
3.6
2.1
3.3
1.7
2.7
2.5
3.8
2.3
3.6
1.9
3.1
3.1
4.7
2.8
4.4
2.3
3.7
3.1
4.7
2.9
4.5
2.5
4
MIN
TYP
MAX
UNIT
SUPPLY CURRENT (3V ≤ VCC1, VCC2 ≤ 3.6V)
ICC1
Supply Current, Side 1
ICC2
Supply Current, Side 2
ICC1
Supply Current, Side 1
ICC2
Supply Current, Side 2
ISO1540
ISO1541
ISO1540 and
ISO1541
ISO1540
ISO1541
ISO1540 and
ISO1541
VSDA1,
VSCL1 = GND1;
VSDA2,
VSCL2 = GND2
VSDA1,
VSCL1 = VCC1;
VSDA2,
VSCL2 = VCC2
See Figure 1;
R1,R2 = Open,
C1,C2 = Open
mA
SUPPLY CURRENT (4.5 V ≤ VCC1, VCC2 ≤ 5.5 V)
ICC1
Supply Current, Side 1
ICC2
Supply Current, Side 2
ICC1
Supply Current, Side 1
ICC2
Supply Current, Side 2
ISO1540
ISO1541
ISO1540 and
ISO1541
ISO1540
ISO1541
ISO1540 and
ISO1541
VSDA1,
VSCL1 = GND1;
VSDA2,
VSCL2 = GND2
VSDA1,
VSCL1 = VCC1;
VSDA2,
VSCL2 = VCC2
PARAMETER
See Figure 1;
R1,R2 = Open,
C1,C2 = Open
TEST CONDITIONS
mA
UNIT
SIDE 1 (Only)
VILT1
Voltage Input Threshold “Low”,
Side 1 (SDA1, SCL1)
500
550
660
VIHT1
Voltage Input Threshold “High”,
Side 1 (SDA1, SCL1)
540
610
700
VHYST1
Voltage Input Hysteresis,
Side 1 VIHT1- VILT1
40
60
VOL1
Low-Level Output Voltage,
Side 1 (SDA1,SCL1)
(1)
ΔVOIT1 (1) (2)
650
Low-Level Output Voltage to High-Level Input Voltage
Threshold Difference,
Side 1 (SDA1, SCL1)
0.5 mA ≤ (ISDA1 and
ISCL1) ≤ 3.5 mA
mV
800
50
SIDE 2 (Only)
VILT2
Voltage Input Threshold “Low”,
Side 2 (SDA2, SCL2)
0.3 x
VCC2
0.4 x
VCC2
VIHT2
Voltage Input Threshold “High”,
Side 2 (SDA2, SCL2)
0.4 x
VCC2
0.5 x
VCC2
VHYST2
Voltage Input Hysteresis,
Side 2 VIHT2 - VILT2
0.05 x
VCC2
VOL2
Low-Level Output Voltage,
Side 2 (SDA2, SCL2)
0.5 mA ≤ (ISDA2 and
ISCL2) ≤ 35 mA
|II|
Input Leakage Currents
(SDA1, SCL1, SDA2, SCL2)
VSDA1, VSCL1 = VCC1;
VSDA2, VSCL2 = VCC2
0.01
CI
Input Capacitance to Local Ground
(SDA1, SCL1, SDA2, SCL2)
VI = 0.4 x sin(2E6πt) +
2.5 V
7
pF
CMTI
Common-Mode Transient Immunity
See Figure 3
25
50
kV/µs
VCCUV (3)
VCC Undervoltage Lockout Threshold
(Side 1 and Side 2)
2.1
2.5
mV
400
BOTH SIDES
(1)
(2)
(3)
4
10
2.8
µA
V
This parameter does not apply to the ISO1541 SCL1 line as it is uni-directional.
∆VOIT1 = VOL1 – VIHT1. This represents the minimum difference between a Low-Level Output Voltage and a High-Level Input Voltage
Threshold to prevent a permanent latch condition that would otherwise exist with bi-directional communication.
Any VCC voltages, on either side, less than the minimum will ensure device lockout. Both VCC voltages above the maximum will prevent
device lockout.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
ISO1540
ISO1541
www.ti.com
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
SWITCHING CHARACTERISTICS
Over recommended operating conditions, unless otherwise noted
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
3 V ≤ VCC1, VCC2 ≤ 3.6 V
Output Signal Fall Time
(SDA1, SCL1)
See Figure 1
R1 = 953 Ω,
C1 = 40 pF
0.7 x VCC1 to 0.3 x VCC1
tf1
tf2
Output Signal Fall Time
(SDA2, SCL2)
See Figure 1
R2 = 95.3 Ω,
C2 = 400 pF
tpLH1-2
Low-to-High Propagation
Delay, Side 1 to Side 2
tPHL1-2
High-to-Low Propagation
Delay, Side 1 to Side 2
PWD1-2
Pulse Width Distortion
|tpHL1-2 – tpLH1-2|
tPLH2-1 (1)
Low-to-High Propagation
Delay, Side 2 to Side 1
tPHL2-1 (1)
High-to-Low Propagation
Delay, Side 2 to Side 1
PWD2-1 (1)
Pulse Width Distortion
|tpHL2-1 – tpLH2-1|
tLOOP1 (1)
Round-trip propagation
delay on Side 1
See Figure 1
R1 = 953 Ω,
R2 = 95.3 Ω,
C1, C2 = 10 pF
See Figure 2;
R1 = 953 Ω, C1 = 40 pF
R2 = 95.3 Ω, C2 = 400 pF
8
17
29
0.9 x VCC1 to 900 mV
16
29
48
0.7 x VCC2 to 0.3 x VCC2
14
23
47
0.9 x VCC2 to 400 mV
35
50
100
0.55 V to 0.7 x VCC2
33
65
ns
0.7 V to 0.4 V
90
181
ns
55
123
ns
0.4 x VCC2 to 0.7 x VCC1
47
68
ns
0.4 x VCC2 to 0.9 V
67
109
ns
20
49
ns
100
165
ns
6
11
20
0.4 V to 0.3 x VCC1
ns
ns
4.5V ≤ VCC1, VCC2 ≤ 5.5V
Output Signal Fall Time
(SDA1, SCL1)
See Figure 1
R1 = 1430 Ω,
C1 = 40 pF
0.7 x VCC1 to 0.3 x VCC1
tf1
0.9 x VCC1 to 900 mV
13
21
39
Output Signal Fall Time
(SDA2, SCL2)
See Figure 1
R2 = 143 Ω,
C2 = 400 pF
0.7 x VCC2 to 0.3 x VCC2
10
18
35
tf2
0.9 x VCC2 to 400 mV
28
41
76
tpLH1-2
Low-to-High Propagation
Delay, Side 1 to Side 2
0.55 V to 0.7 x VCC2
31
62
ns
tPHL1-2
High-to-Low Propagation
Delay, Side 1 to Side 2
0.7 V to 0.4 V
70
139
ns
PWD1-2
Pulse Width Distortion
|tpHL1-2 – tpLH1-2|
38
80
ns
tPLH2-1 (1)
Low-to-High Propagation
Delay, Side 2 to Side 1
0.4 x VCC2 to 0.7 x VCC1
55
80
ns
tPHL2-1 (1)
High-to-Low Propagation
Delay, Side 2 to Side 1
0.4 x VCC2 to 0.9 V
47
85
ns
PWD2-1 (1)
Pulse Width Distortion
|tpHL2-1 – tpLH2-1|
8
21
ns
tLOOP1 (1)
Round-trip propagation
delay on Side 1
110
180
ns
MAX
UNIT
(1)
See Figure 1
R1 = 1430 Ω,
R2 = 143 Ω,
C1, 2 = 10 pF
See Figure 2;
R1 = 1430 Ω, C1 = 40 pF
R2 = 143 Ω, C2 = 400 pF
0.4 V to 0.3 x VCC1
ns
ns
This parameter does not apply to the ISO1541 SCL1 line as it is uni-directional.
TIMING CHARACTERISTICS
PARAMETER
TEST CONDITIONS
tSP
Input Noise Filter
tUVLO
Time to recover from Undervoltage Lock-out
See Figure 4
2.7 V to 0.9 V
MIN
TYP
5
12
30
50
ns
110
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
µs
5
ISO1540
ISO1541
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
www.ti.com
PARAMETER MEASUREMENT INFORMATION
VCC1
R1
+
+
R1
R2
VCC2
R2
SDA1
SDA2
ISO1540/1
SCL1
SCL2
C1
C1
C2
C2
Figure 1. Test Diagram
VCC1
+
SDA1 or
SCL1
Output
-
R1
C1
R2
Isolation
VCC1
GND1
VCC2
SDA1
SCL1 [ISO1540 Only]
C2
tLOOP 1
0.3VCC1
0.4V
GND1
GND2
Figure 2. tLoop1 Setup and Timing Diagram
VCCx
VCCy
2 kW
2 kW
Isolation
Input
+
Output
GNDx
GNDy
VCMTI
Figure 3. Common-Mode Transient Immunity Test Circuit
6
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
ISO1540
ISO1541
www.ti.com
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
PARAMETER MEASUREMENT INFORMATION (continued)
VCCx
VCCy
VCCx
Ry
SDAx or
SCLx
Isolation
0V
Side x, Side y Vccx, Vccy Ry
1, 2
3.3V, 3.3V 95.3Ω
2, 1
3.3V, 3.3V 953Ω
+
Output
-
GNDx
GNDy
or
VCCx
VCCy
VCCy
Ry
0V
Isolation
SDAx or
SCLx
+
Output
-
GNDx
GNDy
VCCx or
VCCy
2.7V
tUVLO
0.9V
Output
Figure 4. tUVLO Test Circuit and Timing Diagrams
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
7
ISO1540
ISO1541
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
www.ti.com
DEVICE INFORMATION
Table 2. IEC INSULATION AND SAFETY-RELATED SPECIFICATION FOR D-8 PACKAGE
Over recommended operating conditions, unless otherwise noted
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
L(I01)
Minimum air gap (Clearance)
Shortest terminal-to-terminal distance
through air
L(I02)
Minimum external tracking
(Creepage)
Shortest terminal-to-terminal distance
across the package surface
CTI
Tracking resistance (comparative
tracking index)
DIN IEC 60112 / VDE 0303 Part 1
>400
V
Minimum internal gap (internal
clearance)
Distance through the insulation
0.014
mm
RIO
Isolation resistance, input to
output (1)
CIO
Barrier capacitance, input to
output (1)
CI
Input capacitance (2)
(1)
(2)
4.8
mm
4.3
mm
VIO = 500 V, TA < 100°C
>1012
Ω
VIO = 500 V, 100°C ≤ TA
>1011
Ω
1
pF
VIO = 0.4 x sin(2E6πt)
See Electrical Characteristics
pF
All pins on each side of the barrier tied together creating a two-terminal device.
Measured from input pin to ground.
spacer
NOTE
Creepage and clearance requirements should be applied according to the specific
application isolation standards. Care should be taken to maintain these distances on a
board design to ensure that the mounting pads for the isolator do not reduce this distance.
Creepage and clearance on the printed-circuit board become equal in certain cases.
Techniques such as inserting grooves and/or ribs on the printed circuit board are used to
help increase these specifications.
Table 3. IEC 60747-5-2 INSULATION CHARACTERISTICS (1)
Over recommended operating conditions, unless otherwise noted
PARAMETER
VIORM
TEST CONDITIONS
SPECIFICATION
Maximum working insulation
voltage
566
Method a, After environmental tests subgroup 1,
VPR = VIORM x 1.6, t = 10 sec,
Partial Discharge < 5 pC
Method b1, After environmental tests subgroup 1,
Input-to-Output test voltage per IEC
VPR = VIORM x 1.875, t = 1 sec (100% production),
60747-5-2
Partial Discharge < 5 pC
VPR
906
1062
After Input/Output safety test subgroup 2/3,
VPR = VIORM x 1.2, t = 10 sec,
Partial Discharge < 5 pC
680
VIOTM
Transient overvoltage per IEC
60747-5-2
VTEST = VOITM
t = 60 sec (qualification)
t = 1 sec (100% production)
4000
RS
Insulation resistance
VIO = 500 V at TS
>109
Pollution degree
(1)
8
UNIT
VPEAK
Ω
2
Climatic Classification 40/125/21
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
ISO1540
ISO1541
www.ti.com
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
Table 4. IEC 60664-1 RATINGS TABLE
PARAMETER
Basic isolation group
Installation classification
TEST CONDITIONS
SPECIFICATION
Material group
II
Rated mains voltage ≤ 150 VRMS
I–IV
Rated mains voltage ≤ 300 VRMS
I–III
Rated mains voltage ≤ 400 VRMS
I–II
Table 5. REGULATORY INFORMATION
VDE
CSA
UL
Certified according to DIN EN 60747-5-2
(VDE 0884 Part 2) and EN 61010-1
Approved under CSA Component Acceptance Notice
5A, CSA/IEC 60950-1 and CSA/IEC 61010-1
Basic Insulation
Maximum Transient Overvoltage, 4000 VPK
Maximum Surge Voltage, 4000 VPK
Maximum Working Voltage, 566 VPK
Basic insulation per CSA 60950-1-07 and IEC 60950-1
(2nd Ed), 390 VRMS maximum working voltage
Basic insulation per CSA 61010-1-04 and IEC 61010-1
Single Protection Isolation Voltage,
(2nd Ed), 300 VRMS maximum working voltage
2500 VRMS (1)
Reinforced insulation per CSA 61010-1-04 and IEC
61010-1 (2nd Ed), 150 VRMS maximum working
voltage
File number: 40016131 (pending)
File number: 220991
(1)
Recognized under UL 1577
Component Recognition Program
File number: E181974
Production tested ≥ 3000 VRMS for 1 second in accordance with UL 1577.
IEC SAFETY LIMITING VALUES
Safety limiting intends to prevent potential damage to the isolation barrier upon failure of input or output circuitry.
A failure of the IO can allow low resistance to ground or the supply and, without current limiting, dissipate
sufficient power to overheat the die and damage the isolation barrier potentially leading to secondary system
failures.
PARAMETER
IS
Safety input, output, or supply
current
TS
Maximum case temperature
TEST CONDITIONS
D-8
MIN
TYP MAX
θJA = 114.6°C/W, VI = 5.5V, TJ = 150°C, TA = 25°C
198
θJA = 114.6°C/W, VI = 3.6V, TJ = 150°C, TA = 25°C
303
150
UNIT
mA
°C
The safety-limiting constraint is the absolute maximum junction temperature specified in the absolute maximum
ratings table. The power dissipation and junction-to-air thermal impedance of the device installed in the
application hardware determines the junction temperature. The assumed junction-to-air thermal resistance in the
Thermal Information table is that of a device installed on a High-K Test Board for Leaded Surface Mount
Packages. The power is the recommended maximum input voltage times the current. The junction temperature is
then the ambient temperature plus the power times the junction-to-air thermal resistance.
ISO154x THERMAL DERATING
350
VCC1 = VCC2 = 3.6 V
Safety Limiting Current (mA)
300
250
200
VCC1 = VCC2 = 5.5 V
150
100
50
0
0
50
100
150
200
o
Case Temperature ( C)
Figure 5.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
9
ISO1540
ISO1541
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
www.ti.com
APPLICATION INFORMATION
I2C™ Bus Overview
The I2C (Inter-Integrated Circuit) bus is a single-ended, multi-master, 2-wire bus for efficient inter-IC
communication in half-duplex mode.
I2C uses open-drain technology, requiring two lines, Serial Data (SDA) and Serial Clock (SCL), to be connected
to VDD by resistors (see Figure 6). Pulling the line to ground is considered a logic Zero while letting the line float
is a logic One. This is used as a channel access method. Transitions of logic states must occur while SCL is
Low, transitions while SCL is high indicate START and STOP conditions. Typical supply voltages are 3.3 V and 5
V, although systems with higher or lower voltages are permitted.
VDD
RPU
RPU
RPU
RPU
RPU
RPU
RPU
RPU
SDA
SCL
SDA
SCL
SDA
SCL
SDA
SCL
SDA
SCL
GND
GND
GND
GND
μC
Master
ADC
Slave
DAC
Slave
μC
Slave
Figure 6. I2C BUS
I2C communication uses a 7-bit address space with 16 reserved addresses, so a theoretical maximum of 112
nodes can communicate on the same bus. In praxis, however, the number of nodes is limited by the specified,
total bus capacitance of 400 pF, which restricts communication distances to a few meters.
The specified signaling rates for the ISO1540 and ISO1541 are 100 kbps (Standard mode), 400 kbps (Fast
mode), 1 Mbps (Fast mode plus).
The bus has two roles for nodes: master and slave. A master node issues the clock, slave addresses, and also
initiates and ends data transactions. A slave node receives the clock and addresses and responds to requests
from the master. Figure 7 shows a typical data transfer between master and slave.
7-bit
ADDRESS
SDA
SCL
R/W
ACK
8
9
1 -7
8-bit
DATA
1 -8
ACK
9
8-bit
DATA
1 -8
ACK /
NACK
9
S
P
START
Condition
STOP
condition
Figure 7. Timing Diagram of a Complete Data Transfer
The master initiates a transaction by creating a START condition, following by the 7-bit address of the slave it
wishes to communicate with. This is followed by a single Read/Write bit, representing whether the master wishes
to write to (0), or to read from (1) the slave. The master then releases the SDA line to allow the slave to
acknowledge the receipt of data.
The slave responds with an acknowledge bit (ACK) by pulling SDA low during the entire high time of the 9th
clock pulse on SCL, after which the master continues in either transmit or receive mode (according to the R/W bit
sent), while the slave continues in the complementary mode (receive or transmit, respectively).
10
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
ISO1540
ISO1541
www.ti.com
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
The address and the 8-bit data bytes are sent most significant bit (MSB) first. The START bit is indicated by a
high-to-low transition of SDA while SCL is high. The STOP condition is created by a low-to-high transition of SDA
while SCL is high.
If the master writes to a slave, it repeatedly sends a byte with the slave sending an ACK bit. In this case, the
master is in master-transmit mode and the slave is in slave-receive mode.
If the master reads from a slave, it repeatedly receives a byte from the slave, while acknowledging (ACK) the
receipt of every byte but the last one (see Figure 8). In this situation the master is in master-receive mode and
the slave is in slave-transmit mode.
The master ends the transmission with a STOP bit, or may send another START bit to maintain bus control for
further transfers.
S Slave Address W A
From Master to Slave
DATA
A
DATA
AP
A = acknowledge
A = not acknowledge
Master Transmitter writing to Slave Receiver
S = Start
From Slave to Master
P = Stop
S Slave Address R A
DATA
A
DATA
AP
Master Receiver reading from Slave Transmitter
R = Read
W = Write
Figure 8. Transmit or Receive Mode Changes During a Data Transfer
When writing to a slave, a master mainly operates in transmit-mode and only changes to receive-mode when
receiving acknowledgment from the slave.
When reading from a slave, the master starts in transmit-mode and then changes to receive-mode after sending
a READ request (R/W bit = 1) to the slave. The slave continues in the complementary mode until the end of a
transaction.
Note, that the master ends a reading sequence by not acknowledging (NACK) the last byte received. This
procedure resets the slave state machine and allows the master to send the STOP command.
Isolator Functional Principle
To isolate a bidirectional signal path (SDA or SCL), the ISO1540 internally splits a bidirectional line into two
unidirectional signal lines, each of which is isolated via a single-channel digital isolator. Each channel output is
made open-drain to comply with the open-drain technology of I2C. Side 1 of the ISO1540 connects to a lowcapacitance I2C node, while Side 2 is designed for connecting to a fully loaded I2C bus with up to 400 pF
capacitance.
VCC1
VCC2
A
RPU1
RPU2
B
SDA1
VC-out
SDA2
ISO1540
Cnode
40mV
Cbus
C
50mV
D
GND1
VREF
VSDA1
GND2
VILT1
VIHT1
VOL1
Figure 9. SDA Channel Design and Voltage Levels at SDA1
At first sight, the arrangement of the internal buffers suggests a closed signal loop that is prone to latch-up.
However, this loop is broken by implementing an output buffer (B) whose output low-level is raised by a diode
drop to approximately 0.75 V, and the input buffer (C) that consists of a comparator with defined hysteresis. The
comparator’s upper and lower input thresholds then distinguish between the proper low-potential of 0.4 V
maximum driven directly by SDA1 and the buffered output low-level of B.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
11
ISO1540
ISO1541
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
www.ti.com
Figure 10 demonstrate the switching behavior of the I2C isolator, ISO1540, between a master node at SDA1 and
a heavy loaded bus at SDA2
VCC2
SDA2
VCC1
VCC1
VCC2
VOL1
SDA1
50%
VIHT1
30%
receive
delay
VCC1
receive
delay
transmit
delay
VCC1
VCC2
VCC2
transmit
delay
SDA1
receive
delay
VIHT2
SDA2
50%
30%
Figure 10. SDA Channel Timing in Receive and Transmit Directions
Receive Direction (left diagram)
When the I2C bus drives SDA2 low, SDA1 follows after a certain delay in the receive path. Its output low will be
the buffered output of VOL1 = 0.75 V, which is sufficiently low to be detected by Schmitt-trigger inputs with a
minimum input-low voltage of VIL = 0.9 V at 3 V supply levels.
Once SDA2 is released, its voltage potential increases towards VCC2 following the time-constant formed by RPU2
and Cbus. After the receive delay, SDA1 is released and also rises towards VCC1, following the time-constant
RPU1 x Cnode. Because of the significant lower time-constant, SDA1 may reach VCC1 before SDA2 reaches
VCC2 potential.
Transmit Direction (right diagram)
When a master drives SDA1 low, SDA2 follows after a certain delay in the transmit direction. When SDA2 turns
low it also causes the output of buffer B to turn low but at a higher 0.75 V level. This level cannot be observed
immediately as it is overwritten by the master’s lower low-level.
However, when the master releases SDA1, its voltage potential increases and first must pass the upper input
threshold of the comparator, VIHT1, to release SDA2. SDA1 then increases further until it reaches the buffered
output level of VOL1 = 0.75 V, maintained by the receive path. Once comparator C turns high, SDA2 is released
after the delay in transmit direction. It takes another receive delay until B’s output turns high and fully releases
SDA1 to move towards VCC1 potential.
12
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
ISO1540
ISO1541
www.ti.com
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
Typical Application Circuit
VS
3.3V
0.1μF
2
Vcc D2 3
1:2.2 MBR0520L
1
SN6501
GND D1
10μF 0.1μF
4,5
OUT
5
ON
GND
5VISO
0.1μF
8
VDD
10μF
LP2981-50
3
1
10μF
IN
9
2
10
1Ω
1
MBR0520L
SDA
0.1μF
0.1μF
1.5k
2
5
6
DVcc
XOUT MSP430
XIN
G2132
SDA
SCL
9
8
DVss
4
0.1μF
1.5k
1.5k
1.5k
1
8
VCC1
VCC2
2
7
SDA1
SDA2
ISO1541
3
6
SCL1
SCL2
GND1
GND2
4
5
SCL
SDA
5VISO
4
4 Analog
Inputs
SCL ADS1115
ADDR
GND RDY
3
ISO-BARRIER
AIN0
AIN3
7
2
5VISO
6
22μF
0.1μF
VOUT
REF5040
15 4 12
3
A2 VDD IOVDD VREFH
11
1
SDA
VOUTA
10
SCL
DAC8574
9
LDAC
14
A1
VOUTD
8
A0 A3 GND VREFL
13 16
6
5VISO
2
VIN
1μF
GND
4
4 Analog
Outputs
5
Figure 11. Isolated I2C Data Acquisition System
In Figure 11, the ultra low-power micro controller, MSP430G2132, controls the I2C data traffic of configuration
data and conversion results for the analog inputs and outputs. Low-power data converters build the analog
interface to sensors and actuators. The ISO1541 provides the necessary isolation between different ground
potentials of the system controller, remote sensor, and actuator circuitry to prevent ground loop currents that
otherwise may falsify the acquired data.
The entire circuit operates from a single 3.3 V supply. A low-power push-pull converter, SN6501, drives a centertapped transformer whose output is rectified and linearly regulated to provide a stable 5 V supply for the data
converters.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
13
ISO1540
ISO1541
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
www.ti.com
TYPICAL CHARACTERISTICS
SIDE 1 OUTPUT LOW VOLTAGE
vs FREE-AIR TEMPERATURE
SIDE 1 OUTPUT LOW CURRENT
vs SDA1 or SCL1 APPLIED VOLTAGE
3.0
0.800
o
0.760
0.740
IOL1 = 3.5 mA
0.720
0.700
TA = 25 C
2.5
Output Current, IOL1 (mA)
Output Voltage, VOL1 (V)
0.780
IOL1 = 0.5 mA
0.680
0.660
0.640
2.0
1.5
1.0
0.5
0.0
0.620
-0.5
0.600
95
110 125
0
0.5
0.6
0.7
SIDE 1 OUTPUT FALL TIME
vs FREE-AIR TEMPERATURE
18
16
14
14
12
10
8
VCC1 = 3.3 V
C1 = 40 pF
Fall Time measured from
70% to 30% VCC1
0
−40 −25 −10
5
20 35 50 65 80
Free-Air Temperature (°C)
95
8
6
2
VCC1 = 5 V
C1 = 40 pF
Fall Time measured from
70% to 30% VCC1
0
−40 −25 −10
110 125
G001
R1 = 1430 Ω
R1 = 2.2 kΩ
5
20 35 50 65 80
Free-Air Temperature (°C)
95
SIDE 2 OUTPUT FALL TIME
vs FREE-AIR TEMPERATURE
SIDE 2 OUTPUT FALL TIME
vs FREE-AIR TEMPERATURE
30
25
25
Fall Time, tf2 (ns)
30
20
15
10
95
20
15
10
5
R2 = 95.3 Ω
R2 = 2.2 kΩ
110 125
110 125
G002
Figure 15.
5
20 35 50 65 80
Free-Air Temperature (°C)
0.9
10
4
R1 = 953 Ω
R1 = 2.2 kΩ
VCC2 = 3.3 V
C2 = 400 pF
Fall Time measured from
70% to 30% VCC2
0.8
12
Figure 14.
0
−40 −25 −10
VCC2 = 5 V
C2 = 400 pF
Fall Time measured from
70% to 30% VCC2
0
−40 −25 −10
G003
Figure 16.
14
0.4
SIDE 1 OUTPUT FALL TIME
vs FREE-AIR TEMPERATURE
16
5
0.3
Figure 13.
20
2
0.2
Figure 12.
18
6
0.1
Applied Voltage, VSDA1, VSCL1 (V)
20
4
Fall Time, tf2 (ns)
5
20 35 50 65 80
Free−Air Temperature (°C)
Fall Time, tf1 (ns)
Fall Time, tf1 (ns)
−40 −25 −10
5
20 35 50 65 80
Free-Air Temperature (°C)
R2 = 143 Ω
R2 = 2.2 kΩ
95
110 125
G004
Figure 17.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
ISO1540
ISO1541
www.ti.com
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
TYPICAL CHARACTERISTICS (continued)
tPLH1-2 PROPAGATION DELAY
vs FREE-AIR TEMPERATURE
tPHL1-2 PROPAGATION DELAY
vs FREE-AIR TEMPERATURE
40
120
C2 = 10 pF
35
30
25
20
15
10
VCC1 and VCC2 = 3.3 V, R2 = 95.3 Ω
VCC1 and VCC2 = 5 V, R2 = 143 Ω
5
0
−40 −25 −10
5
20 35 50 65 80
Free-Air Temperature (°C)
95
100
80
60
40
20
G005
Figure 19.
tPLH1-2 PROPAGATION DELAY
vs FREE-AIR TEMPERATURE
tPHL1-2 PROPAGATION DELAY
vs FREE-AIR TEMPERATURE
90
1045
80
1040
1035
1030
1025
1020
1015
1010
R2 = 2.2 kΩ
C2 = 400 pF
1000
−40 −25 −10
VCC1 and VCC2 = 3.3 V
VCC1 and VCC2 = 5 V
5
20 35 50 65 80
Free-Air Temperature (°C)
95
95
110 125
G006
70
60
50
40
30
20
10
R2 = 2.2 kΩ
C2 = 400 pF
0
−40 −25 −10
110 125
G007
VCC1 and VCC2 = 3.3 V
VCC1 and VCC2 = 5 V
5
20 35 50 65 80
Free-Air Temperature (°C)
Figure 20.
Figure 21.
tPLH2-1 PROPAGATION DELAY
vs FREE-AIR TEMPERATURE
tPHL2-1 PROPAGATION DELAY
vs FREE-AIR TEMPERATURE
70
95
110 125
G008
80
C1 = 10 pF
C1 = 10 pF
60
Propagation Delay, tPHL2−1 (ns)
Propagation Delay, tPLH2−1 (ns)
5
20 35 50 65 80
Free-Air Temperature (°C)
Figure 18.
1050
1005
VCC1 and VCC2 = 3.3 V, R2 = 95.3 Ω
VCC1 and VCC2 = 5 V, R2 = 143 Ω
0
−40 −25 −10
110 125
Propagation Delay, tPHL1−2 (ns)
Propagation Delay, tPLH1−2 (ns)
C2 = 10 pF
Propagation Delay, tPHL1−2 (ns)
Propagation Delay, tPLH1−2 (ns)
45
50
40
30
20
10
0
−40 −25 −10
VCC1 and VCC2 = 3.3 V, R1 = 953 Ω
VCC1 and VCC2 = 5 V, R1 = 1430 Ω
5
20 35 50 65 80
Free-Air Temperature (°C)
95
110 125
70
60
50
40
30
20
10
0
−40 −25 −10
G009
Figure 22.
VCC1 and VCC2 = 3.3 V, R1 = 953 Ω
VCC1 and VCC2 = 5 V, R1 = 1430 Ω
5
20 35 50 65 80
Free-Air Temperature (°C)
95
110 125
G010
Figure 23.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
15
ISO1540
ISO1541
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
tPLH2-1 PROPAGATION DELAY
vs FREE-AIR TEMPERATURE
tPHL2-1 PROPAGATION DELAY
vs FREE-AIR TEMPERATURE
148
Propagation Delay, tPHL2−1 (ns)
Propagation Delay, tPLH2−1 (ns)
146
80
R1 = 2.2 kΩ
C1 = 40 pF
144
142
140
138
136
VCC1 and VCC2 = 3.3 V
VCC1 and VCC2 = 5 V
134
132
−40 −25 −10
5
20 35 50 65 80
Free-Air Temperature (°C)
95
70
60
50
40
30
20
10
R1 = 2.2 kΩ
C1 = 40 pF
VCC1 and VCC2 = 3.3 V
VCC1 and VCC2 = 5 V
0
−40 −25 −10
110 125
5
20 35 50 65 80
Free-Air Temperature (°C)
G011
Figure 24.
140
120
110 125
G012
Figure 25.
tLOOP1 vs FREE-AIR TEMPERATURE
tLOOP1 vs FREE-AIR TEMPERATURE
600
C1 = 40 pF
C2 = 400 pF
595
tLOOP1 (ns)
100
tLOOP1 (ns)
95
80
60
R1 = 2.2 kΩ
C1 = 40 pF
R2 = 2.2 kΩ
C2 = 400 pF
590
585
40
20
580
VCC1 and VCC2 = 3.3 V, R1 = 953Ω, R2 = 95.3Ω
VCC1 and VCC2 = 5 V, R1 = 1430Ω, R2 = 143Ω
0
−40 −25 −10
5
20 35 50 65 80
Free-Air Temperature (°C)
95
VCC1 and VCC2 = 3.3 V
VCC1 and VCC2 = 5 V
575
−40 −25 −10
110 125
G013
5
20 35 50 65 80
Free-Air Temperature (°C)
Figure 26.
95
110 125
G014
Figure 27.
CMTI vs FREE-AIR TEMPERATURE
70
60
CMTI (kV/µs)
50
40
30
20
10
VCC1 and VCC2 = 3.3 V
VCC1 and VCC2 = 5 V
0
−40 −25 −10
5
20 35 50 65 80
Free-Air Temperature (°C)
95
110 125
G015
Figure 28.
16
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
ISO1540
ISO1541
www.ti.com
SLLSEB6A – JULY 2012 – REVISED OCTOBER 2012
TYPICAL CHARACTERISTICS (continued)
SIDE 1 LOW-TO-HIGH TRANSITION
o
500 mV/div
TA = 25 C
VCC1 = 3.6 V
900 mV
VOL1
GND1
Time - 50 ns/div
Figure 29.
Spacer
REVISION HISTORY
Changes from Original (July 2012) to Revision A
Page
•
Changed From: CSA Component Acceptance Notice 5A (Pending) To: CSA Component Acceptance Notice 5A
(Approved) ............................................................................................................................................................................ 1
•
Changed From: IEC 60950-1 and IEC 61010-1 End Equipment Standards (Pending) To: IEC 60950-1 and IEC
61010-1 End Equipment Standards (Approved) ................................................................................................................... 1
•
Changed Table 5, CSA column From: File number: 220991 (pending) To: File number: 220991 ....................................... 9
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: ISO1540 ISO1541
17
PACKAGE OPTION ADDENDUM
www.ti.com
28-Sep-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
ISO1540D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
ISO1540DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
ISO1541D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
ISO1541DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated