S1A THRU S1M SURFACE MOUNT RECTIFIER VOLTAGE - 50 to 1000 Volts CURRENT - 1.0 Ampere FEATURES l l l l l l l SMB/DO-214AA For surface mounted applications High temperature metallurgically bonded-no compression contacts as found in other diode-constructed rectifiers Glass passivated junction Built-in strain relief Easy pick and place Plastic package has Underwriters Laboratory Flammability Classification 94V-O Complete device submersible temperature of 260 ¢J for 10 seconds in solder bath MECHANICAL DATA Case: JEDEC DO-214AA molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard packaging: 12mm tape (EIA-481) Weight: 0.003 ounce, 0.093 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ¢J ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, at TL=100 ¢J Peak Forward Surge Current 8.3ms single half sinewave superimposed on rated load(JEDEC method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current TA=25 ¢J At Rated DC Blocking Voltage TA=125 ¢J Maximum Reverse Recovery Time (Note 1) Typical Junction capacitance (Note 2) Typical Thermal Resistance (Note 3) Operating and Storage Temperature Range SYMBOLS S1A S1B S1D S1G S1J S1K S1M VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 400 280 400 1.0 600 420 600 800 560 800 1000 700 1000 UNITS Volts Volts Volts Amps IFSM 30.0 Amps VF IR 1.10 5.0 50 2.5 12 30.0 -55 to +150 Volts £g A TRR CJ R £KJL TJ,TSTG NOTES: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Irr=0.25A 2. Measured at 1 MHz and Applied Vr=4.0 volts 3. 8.0mm2 (.013mm thick) land areas £g S PF ¢J /W ¢J RATING AND CHARACTERISTIC CURVES AVERAGE FORWARD CURRENT, AMPERES 2.0 PEAK FORWARD SURGE CURRENT, AMPERES S1A THRU S1M SINGLE PHASE HALF WAVE RESISTIVE OR INDUCTIVE P.C.B MOUNTED ON 0.315 ×0.315"(8.0 × COPPER PAD AREAS 1.0 25 50 75 100 125 150 175 30 25 8.3ms SINGLE HALF SINE WAVE 20 JEDEC METHOD 15 10 5 1 2 5 LEAD TEMPERATURE, ¢J 20 50 100 NUMBER OF CYCLES AT 60Hz Fig. 1-FORWARD CURRENT DERATING CURVE Fig. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 100 1,00 INSTANTANEOUS FORWARD CURRENT, MICROAMPERES INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 10 10 TJ = 125 ¢J 1 TJ = 75 ¢J TJ = 25 ¢J 0.1 0.01 0.001 0 20 40 60 80 100 120 140 50 20 10 5.0 2.0 1.0 0.5 0.2 0.1 .05 .02 .01 0.4 PERCENT OF PEAK REVERSE VOLTAGE, % 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig. 3-TYPICAL REVERSE CHARACTERISTICS Fig. 4-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 500 200 2 100 100 UNITS MOUNTED ON CAPACITANCE, pF THERMAL IMPEDANCE(¢J /W) 1000 2 20in (5.4mm ) + 0.5mil in (0.013mm) THICK COPPER LAND AREAS 50 20 10 5 2 1 0.01 50 TJ = 25 ¢J f = 1.0MHz Vsig = 50mVp-p 20 10 5 2 1 0.1 1 10 REVERSE VOLTAGE, VOLTS Fig. 5-TRANSIENT THERMAL IMPEDANCE 100 .1 .2 .4 1.0 2 10 20 40 100 200 400 REVERSE VOLTAGE, VOLTS Fig. 6-TYPICAL JUNCTION CAPACITANCE 1000