PAPERLESS RECORDER DATA SHEET PHR This is a paperless recorder that displays measured data on the LCD in real time and stores data in CompactFlash. The type of input such as thermocouple, resistance bulb, D.C. voltage (current), etc. can be arbitrarily set to 18 channels at the maximum. The data stored in CompactFlash can be regenerated on the screen, and the use of supplied support software allows the data to be regenerated on a PC screen. The data recorded in ASCII format can be directly read in a spreadsheet such as Excel, which facilitates the processing on a PC. (The data recorded in binary format cannot be read in.) FEATURES 1. Large capacity storage by CompactFlash Measured data is periodically stored in CompactFlash. In case of 512 MB, for example, display files for about 3 year and a half (display refresh cycle 30 sec) can be taken up (in case of ASCII data format, 9 channels, maximum/minimum recording). 2.Quick search and display of past data Data stored in CompactFlash can be displayed in succession by scrolling the screen. 3.Various display capability Depending on the object of measurement, the most suitable display format can be selected from a variety of formats including bar graph display, trend display, digital display, etc. 4.PC support software supplied as standard Loader software that enables easy display and change of set data and data viewer software that regenerates the data stored in CompactFlash are supplied as standard. 5.Compact size 160 (W) × 144 (H) × 185 (D) mm(Panel mounting), Compact and as light as about 1.5 kg (9-point input, without option). 6.18-point recording (Option) 12 types of thermocouples, 2 types of resistance bulbs and DC voltage/current input can be recorded up to 18 points 7. Communication function (Option) RS485 MODBUS communication is available. 8.LCD extinguishing function Automatically extinguishes the LCD if nothing is operated for certain time. You can set the time after a lapse of which the LCD is extinguished via parameter "LCD extinguishing time". The settable range is 0 to 60 minutes. Setting at 0 minute overrides the function, whereby the LCD will never extinguish. This function prevents the backlight life from shortening uselessly. During the extinguishment, the power consumption can be reduced. 9.Ethernet function (Option) FTP, Web server, e-mail and MODBUS-TCP are available using 10Base-T. SPECIFICATIONS Input system Number of input points:9 points or 18 points (Can be selected at the time of purchase) Input circuit: Input mutual isolation (See "Others" on page 5 for the withstand voltage) Resistance bulb measured current: about. 1 mA Measuring cycles:9 or 18 points….100ms cycles Recording cycle: 1 second to 12 hours Input types: Thermocouple, resistance bulb, dc voltage, and dc current (Shunt resistors are fitted in input terminals). Note) Provide a shunt resistor (type: PHZP0101) separately. Measuring range Input types Thermocouple B R S K E J T N W L U PN Resistance bulb JPt100 Pt100 Reference range 400.0 0.0 0.0 –200.0 –200.0 –200.0 –200.0 0.0 0.0 –200.0 –200.0 0.0 –200.0 –200.0 to 1760.0ºC to 1760.0ºC to 1760.0ºC to 1370.0ºC to 800.0ºC to 1100.0ºC to 400.0ºC to 1300.0ºC to 1760.0ºC to 900.0ºC to 400.0ºC to 1300.0ºC to 600.0ºC to 600.0ºC 0.00 to 50.00mV 50mV 0.0 to 500.0mV 500mV 1.000 to 5.000V 1-5V 0.000 to 5.000V 0-5V Note) B, R, S, K, E, J, T : JIS C 1602, DIN IEC 584-1 N : NICOSIL-NISIL (IEC 584) W : 5%Re-26%Re · W (Hoskins Mfg. Co. USA) L : Fe-Cu · Ni (DIN 43710) U : Cu-Cu · Ni (DIN 43710) PN: Platinel JPt100 : JIS C 1604-1989 (Old JIS Pt 100) Pt100 : JIS C 1604, DIN IEC 751 DC voltage EDS10-74j Date Dec. 5, 2011 PHR Selection of input types: By key operation on the front panel. Note that the same input type (thermocouple, resistance bulb, voltage) should be set every 2 channels. Refer to "Setting method of input types" for details. Burn-out function: Provided as standard for thermocouple and resistance bulb inputs. If the input has been open-circuited, the recording level swings over 100%. Thermocouple burn-out current: approx. 0.2 µA Input filter function: Settable for each channel (primary delay filter) Time constants are settable in the range from 0 to 900 sec. Scaling function:Possible by dc voltage (current) input Scaling range:-32767 to 32767 Decimal position: settable at any point Unit symbol: Selectable out of 125 different units or 12 user units of up to 7 characters. Subtraction function: Subtraction between each channel is allowed. Totalizing function: The measured value of each channel can be totalized. Applicable to daily, monthly, annual or external input totalizing. F value calculation function: F value (extinction value of bacteria by sterilization by heating) can be calculated from the measured temperature by each channel. F value and measured temperature can be displayed and recorded using 2 channels. Square rooter function: Square rooter can be performed against the input value per each channel. Logarithmic calculation function: The measured value of each channel can be displayed in exponent form. Mathematics function: The following calculation is available with the math function. 1) Computation function Addition, subtraction, multiplication, division, absolute value, exponential, square-root extraction, LOG, LN, EXP, humidity, maximum, minimum, average, and integration. 2) Computation input enable Channel input (1 to 30 CH), Total input (1 to 30 CH), DI (DI to DI10), Communication input (No.1 to No.12), Constant (No.1 to No.20). 2 Indication system 5.7" TFT color LCD (320 × 240 dots) with backlight, no contrast adjustment. On the LCD, certain picture elements remain lit or extinguished. On account o f t h e n a tu r e i n h e r e n t t o L C D, t h e brightness may be non-uniform. But, such are not troubles. Color of indication: 14 colors Applicable language: English, Japanese Life of backlight:50,000 hours (20°C) in terms of total lighting time. (Replace the backlight as a set of display unit. If the LCD extinguishing function is resorted to, the LCD can be used longer as much.) Trend display: Direction: vertical and horizontal Number of channels: 10 or 4 channels per screen group. (select from up to 30 channels). Display refreshment cycles: select from 1 second to 12 hours Scale display or no-display can be selected. Bar graph display: Number of channels: 10 or 4 channels per screen group. (select from up to 30 channels). Display refreshment cycles: 1 second. Analog meter display: For 4 inputs per screen group. (input from 1 to 4). Display in bar graphs or in analog meters can be selected. Display refresh cycle: 1 second Digital display: Number of channels: 10 or 4 channels per screen group. (select from up to 30 channels). Display refreshment cycles: 1 second. Totalizing data display: Number of channels: 10 or 4 channels per screen group. (select from up to 30 channels) Display refresh cycle: 1 second. Event summary display: Alarm summary and message summary can be displayed. The message occurrence information and message display can be switched. Ethernet log display: E-mail sending, FTP server log in/off and MODBUS TCP/IP communication start/stop can be displayed. Parameter display/set: Already-set Data Display and Set Change Display screen TAG indication: Number of characters to be displayed: Up to 8 characters Up to 8 characters (Note 1) at 10-channel display. U p t o 16 ch a r a c t e r s a t 4 channel display. Note 1: Up to 7 characters only can be displayed on certain screens. Indicator: Characters to be displayed: Alphanumerics, hiraganas and katakanas. Tag, unit and channel No. display: Which can be displayed depends on the particular screen. Refer to the table below. (Keywords only are extracted.) Screen Channnels per screen Trend 4 or less 5 or more Bar graph 4 or less 5 or more Analog 4 or less meter 5 or more No. 1 to 4 Others Instantaneous 4 or less value 5 or more x: 1 item only can be displayed +: 2 items only can be displayed –: Nothing can be displayed Tag 1 + x + x x Item Tag 2 Unit ch Np. + + + – x x + + + – x x All All except tag 2 – x All All except tag 2 Historical trend display: Displays past recording data read from compact flash, currently recording data or just recorded data. The recording chart can be scrolled or, via time designation, the control can jump to an arbitrary recording chart. Number of screen groups: Four groups (Up to 10 channels per 1 group can be registered.) Keyboard No. of Keys: Function: 8 Use to select various screens and set various parameters. Recording function External memory media: Compact Flash card Format according to FAT32, FAT16 or FAT. Otherwise, reading and saving are impossible. Recording capacity: 2GB maximum (compact flash). Limiting the recording file to 64 MB is recommended (for 112 hours if display refresh cycle is 1 second. See Table 1 (p. 7).) (When the size of the recording file comes to be 256MB or more, a new file is created automatically and recording is maintained.) * Please change the compact flash every six month to prevent the data losing. Recording method: Turning ON the REC key allows measured data to be written at fixed cycles. Recorded as a new file whenever the recording starts. Data save cycles:Linked to the display refreshment cycles on the ”Real Time Trend” screen. However, they are automatically set to about 1 minute if the refreshment cycles are set to less than 1 minute. Trend data: Measurement data sampled at measurement cycle is saved in terms of mean value, inst ant aneous value or maximum/minimum value. Event data: Saves alarm data and message data. Further saves power ON and OFF, if any, after starting recording. Totalizing value data: Records the totalized data according to the totalizing type selected by channels. Values by totalizing types or total from the beginning of totalizing, whichever selected, can be recorded. For each channel, the input value totalizing, number of DI inputs or measurement at times when DI inputs have occurred can be selected. Input values to be totalized are selected from daily report, monthly report, yearly report and external input. If power has been turned off and on while totalizing, the totalizing is resumed at last value. (Last value remains saved, but data during power OFF is not totalized.) Configuration data: Configuration data can be saved. And this data can also download to recorder. Storage capacity: Approximately 3 years when the display refresh cycle is 30 seconds (in case of 9-channel recording in ASCII data format, and 512 MB compact flash used). Refer to Table 1. Residual capacity of memory: Indicates how much of the memory card has been used on the screen. When all the memory is used up, you can stop recording or delete the oldest recording file to save the newest data. Compact flash card form:PHZP1301, PHZP2801 (CF card) (If a card other than the above is used, no operation assurance is ensured. Meanwhile, as for other CF cards for which operation check will have been completed, the results will be posted on our company's homepage sequentially. Please refer to this website.) Data format: Either of ASCII or binary format can be selected. (Switching cannot be made while the recording is in progress. In the case of ASCII format, the data can be directly read on Excel, etc.) Note: The data recorded in binary format cannot be read directly. Approximately 166 bytes per sampling for maximum/minimum recording of 9-channel input in ASCII format, or approximately 40 bytes for maximum/minimum recording of 9-channel input in binary format. 3 PHR Alarm function No. of settings: Up to 4 alarms for each channel are settable. Type of alarm: High/Low limits Indication: Status (alarm types) is displayed on digital display unit when an alarm occurs. Historical display on alarm summary (Alarm start/cancel time and alarm types) Hysteresis: Set within the recording range of 0 to 100% Acts on high or low limit alarm, and does not affect the battery alarm nor memory full alarm. Relay output: Number of points; 10 (option: Cannot be selected if the number of input points is 18.) Transistor output (open collector output): 18 points (option) Alarm latch function: Holds alarm indication and alarm output even after measurement value has left the alarm range. ON/OFF operation is performed according to key setting. Power supply *1: In case of the 12th digit of ordering code is "Y" or "R". *2: In case of the 12th digit of ordering code is "E" or "W". Reference standard Rated power voltage: 100 to 240V AC Range of operating voltage: 90 to 264V AC Supply frequency: 50/60Hz ±2% (both employable) Power consumption Power voltage Consumption 100V AC About 36VA 240V AC About 47VA Structure Mounting method: Panel-mounted (vertical panel) or portable (desktop type) Thickness of panel: 2 to 26 mm Materials: PC-ABS for case and bezel Color: Black External dimensions: Panel-mounted:160 (W) × 144 (H) × 185 (D) mm Portable: 160 (W) × 171.5 (H) × 206.6 (D) mm Mass: About 1.5 kg (9-point input, without option) External terminal board: Screw terminals (M3 thread) RJ45: Ethernet terminal (option) Operating condition Ambient temperature: Panel-mounted(without Ethernet function): 0 to 50°C*1 Portable: 0 to 40°C Panel mount (with Ethernet function): 0 to 40°C*2 4 Ambient humidity: 20 to 80%RH Vibration: 10 to 60Hz 0.2m/s2 or less Shock: None Magnetic field: 400 A/m or less Signal source resistance: Thermocouple input .... 1kohm or less Resistance bulb input... 10ohm/wire or less (resistance of each wire of 3-wire system should be balanced). Voltage input... 0.1% or less of input resistance Mounting posture: Forward tilt 0º, backward tilt within 30º, horizontal 0º Warm-up time: One hour or more after power ON Environmental protection: IEC IP50 (Front)/20 (Terminal) Installation category: II Pollution degree:2 Operating altitude: 2000m max. Accuracy/resolution: Measuring conditions (23±2ºC, 65± 10% RH, power voltage, frequency fluctuation within ±1%, no external noise, warm-up time of 1 hour or more, vertical mounting, standard values of signal source resistance and wiring resistance... within 1% ) Input types Thermocouple B R S K E J T N W L U PN Resistance bulb DC voltage Digital indication accuracy Note 1 Digital indication resolution ±(0.15%+1 digit) ±(0.3%+1 digit) for the range shown below Thermocouple B : 400 to 600ºC Thermocouples R and S : 0 to 300ºC Thermocouples K, E, J, T, L and U : -200 to -100°C JPt100 ±(0.15%+1 digit) Pt100 50mV 500mV ±(0.15%+1 digit) 5V 0.1°C 0.1°C 10µV 100µV 1mV Note 1) Digital indication accuracy is a percentage (%) with respect to input range of 1 page. Note 2) No error of reference contact compensation of thermocouple is included. Error of reference contact compensation: K, E, J, T, N, L, U, PN: ±0.5ºC R, S, B, W: ±1.0ºC (when measured at 0ºC or more) Max. input voltage: Thermocouple, resistance bulb, dc voltage: ±10V DC (continuous) Input impedance: Thermocouple, DC voltage: About 1MΩ Others With calendar function (Christian era) Accuracy: ±100 ppm or less (monthly error: about 4 minutes) However, time error at ambient temperature 23±2ºC and power ON/OFF is not included. Memory backup:Parameters are saved to the internal non-volatile flash memory. The clock is backed up with built-in lithium battery. Trend data is not backed up. Insulation resistance: 100Ω or more (when measured between each terminal and ground by using a 500V DC megger) Withstand voltage: Input terminal – input terminal: 500 V AC, 1 min Power terminal – ground: 2000V AC, 1 min Input terminal – ground:500V AC, 1 min Alarm terminal (contact output) – ground: 2000 V AC, 1 min Alarm terminal (contact output) – alarm terminal (contact output): 750 V AC, 1 min Communication terminal – ground: 500 V AC, 1 min Alarm terminal (open collector) – ground: 500 V AC, 1 min Power terminal – input terminal: 500 V AC, 1 min Clock: Effect on operation Effect of power supply fluctuation conditions: For the fluctuation in the range from 90 to 264V AC (frequeucy: 50/60Hz) Reading change (100V AC base): ±(0.2%+1 digit) or lower. For the fluctuation in the range from 47 to 63Hz (power voltage: 100V AC) Reading change (50Hz base): ±(0.2%+1 digit) or lower. Effect of input signal resistance: Thermocouple input: (0.5µV/Ω)+1digit or less DC voltage: Fluctuation for resistance value equivalent to 0.1% of the input resistance: ±(0.2%+1 digit) or lower. Reistance bulb (for wiring resistance of 10Ω for 1 line (the same for 3 lines)) Reading change: ±(0.2%+1 digit) or lower. Effect of ambient temperature: Reading change: ±(0.3%+1 digit)/10ºC or lower. Effect of Mounting position: For the backward 30º slant Reading change: ±(0.2%+1 digit) or lower. Effect of vibration: When sine wave of 10 to 60Hz with the acceleration of 0.2m/s 2 is applied in each direction for 2 hours. Reading change: ±(0.2%+1 digit) or lower. Effect of external noise: Normal mode noise (50, 60Hz±0.1Hz) …20dB or more Common mode noise (50, 60Hz±0.1Hz) …120dB or more (Thermocouple input: minus terminalground) (Resistance bulb input: b Line-ground) Safety and EMC standard Safety standard:Based on IEC61010-1 (Portable type does not meet the standard.) EMC standard: Based on EN61326 Transportation/storage conditions Temperature: Humidity: Vibration: Shock: –10 to +60ºC 5 to 90%RH 10 to 60Hz, 2.45 m/s2 or lower 294m/s2 or lower (packed state) Additional function (Option) ■ Alarm relay output/DI (11th digit of code symbols: ”1”) A card with 10-point relay output and 5-point DI input can be mounted. Cannot be mounted if the number of input points is 18. Terminal structure: M3 screw terminal Alarm relay output: 1a contact output (10 points), Individual channel or common output (OR output) allowed. DO1: Contact capacity;150V/3A AC, 30V/3A DC (resistive load) DO2-10: Contact capacity; 240V/3A AC, 30V/3A DC (resistive load) DI input: No-voltage contact input (5 points) The following control is allowed by contact input. (1) Recording start/stop (2) Message set (3) F value calculation reset (4) Totalizing start/stop (5) Totalized value reset (6) LCD (backlight) lighting (7) E-mail sending ON pulse width: 200 msec or more OFF pulse width: 200 msec or more ■ Communication, alarm (open collector output), DI input (12 digit of code symbols is ”R” or ”W”) RS485 communication. Card having 18 alarm points (open collector output) and 5 DI input points can be installed. Terminal structure: M3 thread terminal (DO11 (alarm open collector output), DI6, DIO source terminal and communication terminal) D-Sub 25 pin female terminal (DO12 to DO28 (alarm open collector output)) and DI7 to DI10 Communication:Physical specifications: EIA RS485 Communication protocol: Modbus (RTU) 5 PHR Communication method: 2 wire method. Half duplex bit serial, start-stop sync type. Data type: 8 bits. Parity: odd/even/none. Stop bit: 1 bit. Communication rate: 9600, 19200bps Connection aspect: multi-drop/up to 32 recorders connectable including master station Communication distance: Total extension 500m or less RS232C/RS485 Signal converter (recommendation): Isolated type Manufacture: OMRON Corporation Model: K3SC-10 Alarm output: Open-collector transistor output (18 points) Electrical Rate: 30Vdc, 100mA (resistive load) DI input: No-voltage contact input (5 points). Contact input allows following controls. (1) Recording start/stop (2) Message set (3) F value calculation reset (4) Totalizing start/stop (5) Totalized value reset (6) LCD (backlight) lighting (7) E-mail sending ON pulse width: 200 msec or more OFF pulse width: 200 msec or more Ethernet (Option) The following can be performed through the Ethernet function. ■ HTTP server (Internet Explorer 6 is available) Note 1 Measurement display: Digitally displays the measurement of each channel of the recorder and alarm occurrence status. Event summary display: Displays event summary including alarm ON/OFF and issuance of messages. Main unit information display: Displays memory use conditions and information on the main unit such as the battery end warning. Integrated value display: Digitally displays the integrated value of each channel of the recorder. ■ FTP server (Internet Explorer 6 available.) Note 1 File download: Record files stored in compact flash (CF) can be downloaded from the browser. File delete: Record files stored in CF can be deleted from the browser. Access authentication: Authenticates access authority to FTP server. ■ SMTP (e-mail client) Transmits e-mails to specified address under the following conditions. (1) When an alarm turns on or off (2) When DI is set to ON or OFF (3) When an error occurs to the main u n i t ( s u ch a s l ow b a tt e r y o r n o memory space) (4) At specified intervals 6 ■ MODBUS TC/IP Data read: Settings can be read through MODBUS TCP/IP communication. Data write: Settings can be written through MODBUS TCP/IP communication. Note1: Netscape is not available. Support software Note: Applicable PC: PC/AT-compatible machine Operation on PC98-series machines by NEC is not guaranteed. Operation on self-made or shop-brand PCs is not guaranteed. The following software is provided as standard. ■ Loader software for PC Major function: Performs various parameter setting/ change of the main unit O/S: Windows 2000/XP Required memory: 64MB or larger Disk drive: Windows 2000/XP-capable CD-ROM Hard disk capacity: Free capacity of 30MB or larger required Printer: Windows 2000/XP-capable printer and printer driver Note) PC loader communication cable (type PHZP1801) is separately required. ■ Data viewer software Major function: Regenerates the past trend record on the PC from the data in the compact flash. Provided with historical trend display and event display functions. Data can be changed to CSV file. O/S: Windows 2000/XP Required memory: 64MB or larger Disk drive: W indows 20 0 0/XP-capable CD-ROM drive Hard disk drive: Free capacit y of 30MB or larger required Printer: Windows 2000/XP-capable printer and printer driver Standard functions Function Record range voluntary setting Description Recording range can be set by channel. Input type setting Input type can be set by channel. (Key operation on the front face) Set the same input type for every 2 channels. Skip function Trend display Skips arbitrary channel display/recording. Time display: Time is displayed at the top of the trend display screen. Alarm display: On occurrence of an alarm and the restoration, alarm is displayed in the alarm display field. The compact flash usage is displayed with a bargraph at the top. TAG name display Screen name display Unit creation By channel, Maximum of 8 characters. Displays the screen name (maximum of 16 characters). Industrial units can be arbitrarily created, Maximum of 7 digits, 12 types. Arbitrary scaling is allowed in the case of DC voltage input. Decimal point position can also be arbitrarily set in the range from -32767 to 32767. Scaling function PV shift Shift the zero point and slant of the reading. Input filter Prevents sudden fluctuation of input for each channel (primary delay filter). Time constant: 0 to 900 seconds. Burnout function Displays the break of thermocouple/resistance bulb input by scaling out to 100% side. Historical trend display Regenerates and displays the data stored in the compact flash by scrolling the screen. Displays data of a designated time. Table 1. Recording capacity The recording can be made for the period of time listed in the tables shown below under the following conditions. CompactFlash size 64MB •9 input points Display upgrade cycle 1 sec 10 sec 30 sec 1 min 10 min •Recording data format: ASCII Recordable capacity •Recording type: Maximum/minimum recording 112 hours 46 days 140 days 280 days 7.7 years (about) •No alarm, nor message, nor other events. CompactFlash size 256MB Display upgrade cycle Recordable capacity(about) 1 sec 10 sec 30 sec 1 min 18 days 187 days 1.5 years 3 years •When the number of input points is 18, the period is approximately one half of those listed in the table. •In binary format, the period is approximately 4 times as long as those listed in the table. •For recording type of mean or instantaneous value, the number of days is approximately 2 times as long. While compact flash is not in use, recorded date and event date can be stored approximately 600KB in the main unit When recording 9-channel in MAX-MIN recording, approximately 15300 data can be stored. For 4 hours at the display refresh cycle of 1 second. The number of the save data varies depending on the number of the event data. ORDERING CODE Note 1 2 Note 3 12 13 Recorder (PHR) 1 1 Panel mounting bracket 2 — CD-ROM PC support software instruction manual 1 1 Panel packing for the front face 1 — Noise filter for the power supply 1 1 AC power cord (2m) — 1 OPTIONAL ITEMS Item Code Specification Shunt resistor for DC current input PC loader communication cable PHZP0101 10Ω ±0.1% PHZP1801 Length 3m with connector USB-A/USB miniB terminal * CD-ROM with instruction PHZP0301 manual and support software Terminating resistor for PHZP0701 communication D-Sub light type 25 pin PHZP0801 connector with male terminal for alarm output (without cable) 100Ω PHZP0901 For PHR to PC PHZP1001 For PHR to PHR PC card adapter PHZP0501 For compact flash Compact flash PHZP2801-512 PHZP1301-01G 512MB 1GB * Shape of this cable is shown below USB (A) Plug – USB (Mini-B ) Plug 1 2 B Note 2 100 to 240 V AC 11 Quantity Panel Portable mounting Item Transmission cable 4 5 6 7 8 9 10 11 12 13 B 1 4 1 Y PHR Digit Specifications 4 <Number of input points> 9 channel 18 channel 5 <Mounting> Panel mounting Portable (desktop) 6 <Case color> Black 7 <Compact flash> Without (not furnished) 8 <Version No.> Version No. 9 <Display> Japanese English 10 <Power supply> SCOPE OF DELIVIRY <Alarm (relay) output/DI input> Without With Note 1 1 4 N E 1 0 1 <Communication, alarm (open collector) output/DI input> Without Communication (RS485), alarm output, Di input Note 4 Ethernet Note 5 Ethernet, communication (RS485), alarm output, Di input Note 4,5 <Destination> General Y R E W Y Note 1 : Cannot be selected if 2 is selected for the forth digit (the number of input points is 18). Note 2 : The compact flash is optional. Refer to the section of "Optional items" below. Note 3 : Portable mounting type doesn't comply with UL and CE. Note 4 : Alarm output; transistor (open collector) output Note 5 : Cannot be specified when "2" is selected for the 5th digit. 7 PHR OUTLINE DIAGRAMS (Unit : mm) PANEL MOUNTING TYPE In the case of 9-point input 2 T T 26 DI input & alarm terminal (option) Mtg.bracket Ethernet terminal (option) Input terminal (points 1 to 9) Source terminal L DIOSHLD A6 DO11 COM 24VDC IN DIO-ON TRX1 TRX2 R-MODULE Rcj Fuji Electric 144 136.5 161 N 100 240VAC Panel 160 140 21.6 136.5 185 DIO terminal (D-Sub) (option) 24.6 when panel packing is mounted Communication DIO terminal (option) (Note) When placing the main unit on another instrument or on the floor, allow a space of 100mm or more between the unit and instrument or the floor. In the case of 18-point input Ethernet terminal (option) Input terminal (points 1 to 9) T Input terminal (points 10 to 18) Mtg.bracket Source terminal L TRX1 TRX2 R-MODULE Rcj Fuji Electric DIO-ON R-MODULE Rcj Fuji Electric 144 136.5 161 N 100 240VAC 2 T 26 DIOSHLD A6 DO11 COM 24VDC IN Panel 160 140 21.6 136.5 185 24.6 when panel packing is mounted DIO terminal (D-Sub) Communication DIO terminal (Note) When placing the main unit on another instrument or on the floor, allow a space of 100mm or more between the unit and instrument or the floor. Panel cutout Mounting one unit Mounting close together sidewise (160 × n−22) +20 n : Number of units to be mounted 137 +1.5 0 137 +1.5 0 137 +1.5 0 Do not use the water proof pacing in case of mounting n unit 8 PORTABLE (TABLE TOP) TYPE In the case of 9-point input Handle DI input & alarm terminal (option) Source terminal DIOSHLD A6 DO11 COM 24VDC IN DIO-ON 160 15 49 TRX1 TRX2 R-MODULE Rcj Fuji Electric 144 136.5 208.5 20 Input terminal (points 1 to 9) 136.5 140 21.6 185 DIO terminal Communication (D-Sub) (option) DIO terminal (option) Foot Stand-foot (Note) Please use the stand-foot upright. In the case of 18-point input Handle Input terminal (points 10 to 18) Input terminal (points 1 to 9) DIOSHLD A6 DO11 COM 24VDC IN DIO-ON 160 21.6 15 49 TRX1 TRX2 R-MODULE Rcj Fuji Electric R-MODULE Rcj Fuji Electric 144 136.5 208.5 20 Source terminal 140 185 Stand-foot Foot 136.5 DIO terminal Communication (D-Sub) (option) DIO terminal (option) (Note) Please use the stand-foot upright. 9 PHR EXTERNAL CONNECTION DIAGRAMS PANEL MOUNTING TYPE In the case of 9-point input Source terminal M3 thread Resistance Thermo- Voltage bulb Voltage Thermo- Resistance bulb couple couple + + 11 + + 61 CH1 12 CH6 62 13 63 + + 21 + + 71 22 CH2 72 CH7 23 73 + + 31 CH3 32 RCJ 33 + + 41 + + 81 CH4 42 82 CH8 43 83 + + 51 + + 91 CH5 52 92 CH9 53 93 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 DI1 DI2 DI3 DI4 DI5 DO1 DO2 DO3 DO4 DO5 DO6 DO7 DO8 DO9 DO10 M3 thread M3 thread AC100 240V 50/60Hz (Note) For current input, connect an optional shunt resistance to a voltage input terminal PCD 1 14 13 25 6 7 8 9 10 11 12 15 16 17 18 19 20 21 22 23 24 2 3 4 5 VPD PCD DO12 DO13 DO14 DO15 DO16 DO17 DO18 DO19 DO20 DO21 DO22 DO23 DO24 DO25 DO26 DO27 DO28 DI7 DI8 DI9 DI10 VPD VPD 24Vdc Input terminal DIO(+24V) PCD PCD DIO(0V) DO11 DI6 SHLD TRX2 – TRX1 + (shield) (–) (+) MODBUS communication Alarm output/digital input terminal Communication, digital input and alarm (open collector) output terminal (M3 thread) PCD Digital input and alarm (open collector) output terminal, D-Sub terminal In the case of 18-point input Input terminal Source terminal Resistance Thermo- Voltage bulb couple + + 11 61 - CH1 12 62 13 63 + + 21 71 - CH2 22 72 23 73 + + 31 - CH3 32 M3 thread Thermo- Resistance bulb couple - - + + - - RCJ + + - - + - + - 33 81 82 83 91 92 93 41 42 43 51 52 + + - - + + - - AC100 240V 50/60Hz CH4 CH5 53 (Note) For current input, connect an optional shunt resistance to a voltage input terminal PCD 1 14 13 25 6 7 8 9 10 11 12 15 16 17 18 19 20 21 22 23 24 2 3 4 5 VPD PCD DO12 DO13 DO14 DO15 DO16 DO17 DO18 DO19 DO20 DO21 DO22 DO23 DO24 DO25 DO26 DO27 DO28 DI7 DI8 DI9 DI10 VPD VPD DIO(+24V) PCD DIO(0V) DO11 PCD DI6 SHLD TRX2 – TRX1 + Communication, digital input and alarm (open collector) output terminal (M3 thread) PCD Digital input and alarm (open collector) output terminal, D-Sub terminal 10 (shield) (–) (+) 24Vdc MODBUS communication Resistance Thermo- Voltage Voltage bulb Voltage Thermo- Resistance bulb couple couple + + 111 + + 161 - CH10 112 162 CH15 CH6 113 163 + + 121 + + 171 - CH11 122 172 CH16 CH7 123 173 + + 131 - CH12 132 RCJ 133 + + 141 + + 181 - CH13 142 182 CH17 CH8 143 183 + + 151 + + 191 CH14 152 192 CH18 CH9 153 193 M3 thread PORTABLE (TABLE TOP) TYPE In the case of 9-point input Input terminal M3 thread 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 Resistance Thermo- Voltage bulb couple Voltage Thermo- Resistance bulb couple DI1 DI2 DI3 DI4 DI5 DO1 DO2 DO3 DO4 DO5 DO6 DO7 DO8 DO9 DO10 CH6 CH7 + + - - + + - - 61 62 63 71 72 73 RCJ CH8 CH9 + + - - + + - - 81 82 83 91 92 93 Source terminal (Inlet) M3 thread 11 12 13 21 22 23 31 32 33 41 42 43 51 52 53 + + - - + + - - + + - - + + - - + + - - AC100 240V 50/60Hz L CH1 CH2 N CH3 CH4 CH5 (Note) For current input, connect an optional shunt resistance to a voltage input terminal PCD 1 14 13 25 6 7 8 9 10 11 12 15 16 17 18 19 20 21 22 23 24 2 3 4 5 VPD PCD DO12 DO13 DO14 DO15 DO16 DO17 DO18 DO19 DO20 DO21 DO22 DO23 DO24 DO25 DO26 DO27 DO28 DI7 DI8 DI9 DI10 VPD VPD DIO(+24V) PCD DIO(0V) DO11 PCD DI6 SHLD TRX2 – TRX1 + (shield) (–) (+) 24Vdc MODBUS communication Alarm output/digital input terminal Communication, digital input and alarm (open collector) output terminal (M3 thread) PCD Digital input and alarm (open collector) output terminal, D-Sub terminal In the case of 18-point input Voltage CH15 CH16 Thermo- Resistance Resistance Thermocouple Voltage bulb couple bulb + + - - + + - - RCJ CH17 CH18 + + - - + + - - 111 161 112 162 113 163 121 171 122 172 123 173 131 132 133 141 181 142 182 143 183 151 191 152 192 153 193 + + - - + + - - + + - - + + - - + + - - CH10 CH11 Voltage CH6 CH7 CH13 CH14 Thermo- Resistance Resistance Thermocouple Voltage bulb couple bulb + + - - + + - - CH12 Source terminal (Inlet) M3 thread 61 62 63 71 72 73 RCJ CH8 CH9 + + - - + + - - 81 82 83 91 92 93 11 12 13 21 22 23 31 32 33 41 42 43 51 52 53 + + - - + + - - + + - - + + - - + + - - CH1 AC100 240V 50/60Hz L CH2 N CH3 CH4 CH5 (Note) For current input, connect an optional shunt resistance to a voltage input terminal PCD 1 14 13 25 6 7 8 9 10 11 12 15 16 17 18 19 20 21 22 23 24 2 3 4 5 VPD PCD DO12 DO13 DO14 DO15 DO16 DO17 DO18 DO19 DO20 DO21 DO22 DO23 DO24 DO25 DO26 DO27 DO28 DI7 DI8 DI9 DI10 VPD VPD DIO(+24V) PCD DIO(0V) PCD DO11 DI6 SHLD TRX2 – TRX1 + (shield) (–) (+) 24Vdc MODBUS communication Input terminal Communication, digital input and alarm (open collector) output terminal (M3 thread) PCD Digital input and alarm (open collector) output terminal, D-Sub terminal 11 PHR Selecting input type The input type is the same every 2 channels. The input type of channel 2, 4, 6, 8, 11, 13, 15 and 17 can only be set in the same category of previous channel. The following input types are available. Input type Details Thermocouple, 50mV Resistance bulb K, E, J, T, R, S, B, N, W, L, U, and PN thermocouples, 50mV Pt100, JPt100 500mV 500mV 1 to 5V, 0 to 5V 5V Other channels Other channels (*1) Note, however, that input type can be arbitrarily selected only for channels 9 and 18 irrespective of the type allocated to other channels. *1: Used for F value calculation, for example. If an input type is allocated to another channel, or, if the input type of channel 2 is allocated to other channels and several settings are made when the temperature is being measured by connecting K thermocouple to channel 1, it is possible to display a temperature measured by K thermocouple on channel 2. F value calculation is available on channel 1, and the temperature recording is available on channel 2. For setting method, refer to the instruction manual. Example of channel input type selection Input type Input type Channel 1 K thermocouple Channel 2 T thermocouple Thermocouple, 50mV Channel 3 1-5V Channel 4 0-5V Channel 5 Pt100 Channel 6 JPt100 Channel 7 500mV Channel 8 500mV Description The type of thermocouple can be arbitrarily selected for each channel. 5V Resistance bulb The type of resistance bulb can be arbitrarily selected for each channel. 500mV Channel 9 J thermocouple Thermocouple, 50mV Input type can be arbitrarily selected for channel 9. Channel 10 K thermocouple Channel 11 50mV Thermocouple, 50mV The input type of the thermocouple and 50mV is the same. Channel 12 Skip 5V Channel 13 1-5V Skip and other channel can arbitrarily be selected irrespective of the input type. Channel 14 Pt100 Channel 15 Skip Channel 16 Other channels Channel 17 500mV Channel 18 50mV Resistance bulb 500mV Thermocouple, 50mV Input type can be arbitrarily selected for channel 18. Note 1) Windows2000/XP, Excel, and Internet Explorer are the trademarks or registered trademarks of Microsoft Corporation in the U.S. Note 2) CompactFlash is a trademark or registered trademark of Sandisk Corporation. Note 3) Modbus is the trademark or registered trademark of AEG Schneider Automation International. Note 4) The PC98 Series is are the trademark or registered trademark of NEC Corporation. Note 5) Netscape is the trademark or registered trademark of Netscape Communications Corp. Caution on Safety *Before using this product, be sure to read its instruction manual in advance. International Sales Div Sales Group Gate City Ohsaki, East Tower, 11-2, Osaki 1-chome, Shinagawa-ku, Tokyo 141-0032, Japan http://www.fujielectric.com Phone: 81-3-5435-7280, 7281 Fax: 81-3-5435-7425 http://www.fjielectric.com/products/instruments/ Information in this catalog is subject to change without notice. Printed in Japan