FUJI EDS11-162

COMPACT CONTROLLER M [CC-M]
(FIXED FUNCTION/ STEP OUTPUT TYPE)
Digital Controller
DATA SHEET
PDC1
The Compact Controller M (fixed function/step output type)
is a single-loop process controller.
Receiving 1 to 5V DC signals as well as those from thermocouples and resistance bulbs as input signals, it performs
advanced controls such as PID control, square root extraction, and non-linear control.
FEATURES
1. Single-loop controller with control output
The controller has a single-loop control function.
2. High visibility ensured by color graphic display
A color LCD is adopted for clear graphic displays such as
bar graph and trend displays.
3. Networking (option)
Communication can be carried out over our PLC-link
(T-link) or Modbus (RS485) network.
4. Memory card (option)
The data such as process input data and control output
data can be saved in memory cards.
FUNCTIONAL DIAGRAM
Bar graph indicator
To other controllers
Communication
terminal
Valve position input (AI1)
R-SV(PV2)
Filter
Square-root
extraction
Limiter
H
R,A
L
Limiter
M
Pulse width
conversion
Non-linear
R
SH
SL
Pulse input (DI1,DI2)
Pulse input switching
Command (DI9)
Forced M command
(DI10)
MV
P
I
D
A.M
Control output
(Pulse output: DO1, DO2)
D/A converter
4 to 20mA,
thermocouple/
resistance bulb
conversion
Internal input
terminal
Process value input (PV1)
A/D converter
Linearize
Valve position output
(voltage:AO2,AO5)
Compensated PV signal (AO3)
Set point transmit signal (AO4)
Manual mode output
(M:DO6)
Local mode output
(DO7)
Remote request
(DO8)
M mode
L mode
M mode
External output terminal
External input terminal
Personal computer
R
C
Fault output (FLT)
PV tracking (DI7)
High alarm output (DO9)
Low alarm output (DO10)
Deviation upper limit alarm (DO4)
Deviation lower limit alarm (DO5)
Rate of change upper/lower limit
alarm (DO3)
R mode
R-ACK(DI8)
Fault
FLT lamp
Alarm
: Option
EDS11-162
Date
Aug. 19, 2005
PDC1
SPECIFICATIONS
1. Control Functions
(1) PID control
• Number of loops and PID:
1 loop (1 control output / 1PID)
• Proportional band (P):
1.0 to 3276.7%, set at 3000.0% for delivery
• Integration time (I):
0.1 to 3276.7 s, set at 3000.0 s for delivery
• Derivative time (D):
0.0 to 900.0 s, set at 0.0 s for delivery
(2) Computation cycle:
100 ms
(3) Alarm function
• Kinds
: Each high/low of PV and SV, PV change
rate alarm, high/low deviations.
2. Input Signals
Performance in standard operating conditions (23± 2°C,
55± 10% RH, power supply voltage 100 V AC to 240 V AC
power frequency 50/60 Hz, or 24 V DC, without vibration
and external noise).
2-1 Analog input signal
• Number of inputs:
3 (points used)
• Inpute signal types:
DC voltage, thermocouple (option), resistance bulb (option)
One thermocouple input or one resistance bulb input are selectable in Code
Symbol.
(1) DC voltage/DC current
• Open-angle input is assigned to AI1 in
an unchangeable manner.
• Input range: Selectable among 0 to 5 V
DC, 1 to 5 V DC and 0 to 10 V DC
Initial set before delivery : 1 to 5 V DC
• Input accuracy: ± 0.1% of input span± 1
digit
• Scaling (Engineering data conversion):
Settable within a range from -32767 to
32767
4, 3, 2, 1 or 0 digit below decimal point
is selectable.
Initial set before delivery : 0.00% to
100.00%
• Engineering unit: Settable in up to 8
characters
Usable characters: Alphabets numerals,
symbols such as +, – ,*,etc.
• Input accuracy guarantee range: -5%
to 105% of input range. However, minus inputs are excluded.
• Maximum continuous permissible
voltage: ± 35 V
• Input resistance: 1 MΩ or more
• Influence by ambient temperature:
± 0.1% FS/10°C or less.
• Influence by power supply fluctuation:
± 0.1% FS or less.
• Isolation: Non-isolated from internal circuit.
2
• In case of current input:
Shunt resistor need to be connected to
the analog input terminal.
(250 Ω shunt resistor is optional item)
(2) Thermocouple (option)
• Types and measurable ranges:
* See Table 1.
• Input accuracy: ± 0.2% FS ± 1 digit
[Note]B type: ± 5% between 0 to 400˚C
S and R type: ±1%between 0 to 500˚C
All type of TC: ± 5% under–100˚C
• Reference junction compensation error:
± 1.0°C (provided measurable range is
–50°C and higher)
[Note]Reference junction compensation resistor is connected at external
input terminal in case of thermocouple input is ordered.
• Input accuracy guarantee range:
–5% to 105% of input range
• Input resistance: 1MΩ or more
• Influence by signal source resistance:
About 0.25 µV/Ω
• Influence by ambient temperature:
± 0.2% FS/10°C ± 1°C or less.
• Influence by power supply fluctuation:
± 0.2% FS ± 1˚C or less
• Burnout detection: Provided
• Isolation: Isolated from internal circuit.
(3) Resistance bulb (option)
• Types and measurable ranges:
* See Table 1.
• Input accuracy: ± 0.2% FS ± 1 digit
• Input accuracy guarantee range:
-5% to 105% of input range
• Allowable wiring resistance: 10Ω or
less per wire, provided wiring resistance must be equal among 3 wires (Zener barrier connection unallowable)
• Influence by ambient temperature: ± 0.2% FS/10˚C or less.
• Influence by power supply fluctuation: ± 0.2% FS or less
• Burnout detection: Provided
• Isolation: Isolated from internal circuit.
[Note] FS: full span.
• Sampling period:
100 ms
2-2 Digital input signal
• Number of inputs:
6 inputs
• Electrical specifications:
No-voltage contact or transistor contact
ON/0 V, OFF/24 V, ON current/about 8
mA
Isolated from the internal circuit by
photocoupler. Not isolated between
each digital input and output.
• Contact rating: 30 V DC, 10 mA or more
• Signal judgment:
No-voltage contact
Contact resistance;
200 Ω or less at ON,
100 kΩ or more at OFF
Transistor contact
1V max at ON.,
leakage current 100µA max. at
OFF
3. Output Signals
Performance in standard operating conditions (23± 2°C,
55± 10% RH, power supply voltage 100 V AC to 240 V AC
power frequency 50/60 Hz, or 24 V DC, without vibration
and external noise).
3-1 Analog output signal
(1) Auxiliary analog output
• Number of outputs:
4 (points used)
• Types of signal : Selectable among 0 to 5 V DC, 1 to 5 V
DC and 0 to 10 V DC
Initial set before delivery: 1 to 5 V DC
• Output accuracy:
± 0.1% FS
• Load resistance:
15 kΩ or more
• Output guarantee range:
• 1 to 5 VDC : –12.5% to 112.5%
• 0 to 5 VDC : 0% to 112.5%
• 0 to 10VDC : 0% to 105%
• Influence by power supply fluctuation:
± 0.1% FS or less
• Isolation
: Non-isolated from internal circuit
3-2 Control output signal
• Number of outputs:
1 pair
Increasing pulse; DO1
Decreasing pulse; DO2
• Electrical specifications:
Transistor open collector
1 V max. at ON, 10 µA max at OFF.
Isolated from the internal circuit by
photocoupler. Not isolated between
each digital input and output.
• Output rating : 30 V DC, 100 mA max. (resistive load)
[Note] Control outputs should be crossed sequentially
by an external sequence so that the increasing and
decreasing pulse signals are not turned to ON at the
same time.
3-3 Digital output signal
• Number of outputs:
8 (points used)
• Electrical specifications:
Transistor open collector
1 V max. at ON, 10 µA max at OFF.
Isolated from the internal circuit by
photocoupler. Not isolated between
each digital input and output.
• Output rating : 30 V DC, 100 mA max. (resistive load)
3-4 Fault output signal (terminal symbol FLT)
• Number of outputs:
1 output
• Electrical specifications:
Transistor open collector
1 V max. at ON, 10 µA max at OFF.
Isolated from the internal circuit by
photocoupler. Not isolated between
each digital input and output.
• Output rating : 30 V DC, 100 mA max. (resistive load)
4. Display
• Display unit
: 16 Colors graphic liquid crystal display,
with CFL back light and contrast adjust
function.
• Contents of display:
• Menu
• Loop panel
Bar graph display, digital display, etc.
• Tuning screen
• Trend screen
• Alarm and alarm historical screen
• Analog input/output and digital input/
output indication screen
• Parameter setting screen
5. Setting and Operation
(1) Set point setting method
• Setting key
: Up key/down key
• Setting speed : About 40 s/FS
• Setting resolution:
0.05% FS/each key press
(2) Control output operation method
• Operation key : Up key, down key
(3) Operation mode
• Selectable operation modes:
C (or R), A and M modes
[Note] C: Cascade mode (mode of operation according
to external set value)
R: Remote mode (mode of operation according
to external set value)
A: Auto mode (mode of operation according to
the value set on front face of this controller)
M: Manual mode (operation mode in which operator manipulates control output manually)
[Supplement] In the C and R modes, operations
are the same, i.e., only the markings on the nameplate are different.
• Setting method :
Selection is required in Code Symbol
among the following.
C-A-M
A-M
R-A-M
• Operation mode changeover:
Balance bumpless transfer from A to R
and from A to C. Balanceless bumpless
transfer in other mode changeover.
[Note] Balance bumpless transfer is a mode in which
the operator is required to balance each SV for
transfer.
Balanceless bumpless transfer is a mode in
which the controller automatically balances each
SV for transfer.
3
PDC1
(4) Security
• Method
• Password
: Setting of a password
: Settable in 4 numerals (within 0000 to
ffff)
Initial set before delivery: 0000
• Contents of security:
Inhibition of parameter setting
(5) Other setting items
• Tag name
: Settable in up to 8 characters
Usable characters; alphabes, numerals, symboles such as +, – ,*,etc.
6. Power Supply
• Voltage rating : 100 V to 240 V AC/24 V DC
[as specified in Code Symbol]
• Allowable range:
85 V to 264 V AC/20 V to 30 V DC
[as specified in Code Symbol]
• Frequency
: 47 to 63 Hz
• Power consumption:
60 VA or less (100 V to 240 V AC)/
30 W or less (24 V DC)
[as specified in Code Symbol]
• Power supply output voltage:
(terminal symbol VP and PC)
20V to 30V DC,max. 40mA
7. General performance and characteristics
• Insulation resistance:
500 V DC, 50 MΩ or more.
• Dielectric strength:
• 2,000 V AC for 1 minute between
power terminal and ground terminal in
case of 100 V to 240 V AC power supply
• 500 V AC for 1 minute between power
terminal and ground terminal in case of
24 V DC power supply.
• 500 V AC for 1 minute between signal
communication terminals and ground
terminal
• Rush current : 60 A or less. (100 V AC to 240 V AC
power supply)
• Clock
: Set and display year, month, day, hour,
minute, second
Accuracy : ± 100 ppm (monthly gain/
loss about 4 minutes) except of time lag
shorter than 1 s / power ON / OFF action.
• Memory backup:
• Protection by lithium battery.
(expected battery life is about 2 years
under room temperature)
• Parameter and program are stored in
non-volatile memory.
4
8. Operating and storage conditions
• Installation site : Indoors
• Operating temperature:
0 to 50˚C
0 to 40°C in case of multiple mounting
Temperature change rate: Max. 10˚C / h
• Transport and storage temperature:
-20 to 70˚C
(Temperature change rate: Max. 20˚C / h)
• Operating humidity:
5 to 90% RH, condensation unallowable
• Transport and storage humidity:
5 to 95% RH, condensation unallowable
• Operating continuous vibration:
4.9 m/s2 or less
• Transport and storage shock:
Fall of 60cm max. in packed status
9. Power Failure and restart Function
• Permissible duration of momentary power failure:
20 ms at 90V AC (100 V to 240 V AC
only)
[Note] In case of 24 V DC, system power supply unit
(model: PXJ) is recommended to avoid power failure
problem.
• Behavior at power failure detection:
Control stops at detection of power failure.
• Power recovery mode:
Selectable initial start and continuous
start
10. Self-Diagnosis
• Control and computation circuit failure:
Monitoring with watchdog timer
• Input signal failure:
• Voltage/current input
Monitoring of range over
• Thermocouple and resistance bulb
Monitoring of disconection
• Behavior at failure:
: FLT is indicated, FLT lamp lights, FLT
output signal turns on, control stops and
control output is OFF (Open-angle of
valve is held).
11. Structure
• Enclosure
: Plastic (material: PC-ABS)
• Finish color
: Front frame and enclosure both gray
• Flame resistance:
UL94V-0
• Protection
: Front face; IP54 (display unit and operation key)
• External dimensions (width x height x depth):
Screw terminal type 72 x 144 x 272 mm
Compression terminal type 72 x 144 x
280 mm
• Mass
: 1.9 kg or less
• Mounting method:
Flush on indoor panel
Vertical mounting as standard
Tilted mounting allowed within backward angle 0° to 45°.
90° to 45°
For panel cutout dimension, refer to
Panel Cutout Dimensions
• External terminal:
Selectable in Code Symbol between the
following.
Screw terminal type (M3.5)
Compression terminal type
12. Communications (option)
12-1 Modbus(R) protocol interface (option)
• Communication mode: Host communications
• Communication protocol: Modbus(R) protocol
• Physical specifications: EIA RS485
• Communication mode: Two-wire, half-duplex, start-stop
synchronous mode
• Connection mode: Multi-drop connection
• Communication speed: Selectable from 2.4, 4.8, 9.6,
19.2, and 38.4 kbps.
Default setting: 19.2 kbps
• Communication distance: Total extension; Max. 500 m
• Data length: Fixed to 8 bits
• Parity: Selectable from ODD, EVEN, or None.
• Stop bit: Selectable from 1 or 2.
• Insulation: Isolated from internal circuit
• End of line resistor: 100 Ω (option)
• Communication item: Parameter, measured value
• RS232/RS485 converter (recommended item)
Type: K3SC-10 (Insulated type by OMRON)
12-2 T-link interface (option)
• Communication mode:
Communication with upper level
• High order communication:
Connection with CPU capsule
I/O transmission; 8 words output
• Low order communication:
None
• Common item: Topology; Multidrop
Communication speed; 500 kbps
Communication distance;
Max. 500 m in total extension distance
Isolation; Not isolated from internal circuit
Terminating resistor; 100 Ω (separately
available)
• Data storage capacity:
Memory card
capacity
Data storge
4MB
about 180 thousand data
20MB
about 900 thousand data
32MB
about 1.35 million data
[Note] The data of max. 16 points (4 screens) can be
storaged at storage time as 1 s.
• Format method:
Dependent on this controller
• Data readout : Readout by PC using PCMCIA card slot
• Recommended memory card:
Made by Sandisk corporation
Sandisk compact Flash memory card is
standardized and on the market.
14. Standards under Conformity
(1) General safety:
IEC 1010-1 (1990)
EN 61010-1 (1993)
(2) EMC
: Emission EN 50081-2 (1994)
Immunity EN 50082-2 (1995)
[Caution on use]
1. Unlike the preceding models, a potentiometer interface
(resistance input) for inputting the open angle of a motoroperated valve is not incorporated. For the above purpose, therefore, voltage input is required with a signal
converter externally connected.
Also, since open-angle input is assigned between AI1 and
SC, this input will be indicated on the MV indicator.
2. Control output is assigned to the multi-connector section.
So, a 34-pin multi-connector should be prepared depending on your specifications, referring to "Items to be ordered separately (items separately available)."
3. For control output, crossing interlock with relays or the
like interlock is required so that both incremental and decremental pulse signals will not turn on simultaneously.
13. Memory Card Interface (option)
• Specification : Compact Flash® (Based on CFA)
• Compatible memory card:
5 V flash memory card
Capacity 4, 20 and 32 MB
• Application
: Process data logging (3 points)
• Saving period : 1s to 2h
5
PDC1
Table 1
SCOPE OF DELIVERY
List of Thermocouple and Resistance Bulb Measurable
range
Input signal
Thermocouple
Controller, panel mounting bracket, instruction manual
(depend on code symbols)
Input type code Input range code Measurable range˚C
J
00
0.0~400.0
J
01
01
0.0~800.0
K
02
0.0~400.0
K
03
0.0~800.0
K
04
0.0~1200.0
Items to be ordered separately (items separately available)
Item
Type
Specificatio
Unit of
sale
Terminating
PDZR1001
For screw terminal
1
resistor (100 Ω)
PDZR2001
For compression terminal
1
34-pin multi-connector
PDZC1001
Soldering type straight terminal
1
PDZC2001
Soldering type right-angle terminal
1
1
R
05
0.0~1600.0
B
06
0.0~1800.0
PDZC3001
Solderless type straight terminal
T
07
-200.0~200.0
PDZC4001
Solderless type right-angle terminal
1
T
08
-150.0~400.0
PDZS1001
For screw terminal
1
E
09
0.0~800.0
PDZS2001
For compression terminal
1
PDZK1xx1
With M3.5 solderless
1
(Note 1)
Shunt resistor (250 Ω)
Communication cable (Note2)
E
10
-200.0~800.0
S
11
0.0~1600.0
N
12
0.0~1300.0
U
13
-200.0~400.0
WRe5-26
14
0.0~2300.0
For screw terminals
PL2
15
0.0~1300.0
between PDC and PC
00
0.0~150.0
For screw terminals
Resistance bulb Pt100
00
JPt100
01
0.0~300.0
02
0.0~500.0
between PDC and PDC
For screw terminals
terminal at both ends
PDZK2xx1
between PDC and PLC
For compression terminal
PDZK3xx1
9-pin connector on
PDZK4xx1
With compression
PDZK5xx1
With M3.5 solderless
0.0~600.0
-50.0~100.0
05
-100.0~200.0
06
-200.0~600.0
07
-200.0~850.0
08
0.0~150.0
09
0.0~300.0
Printed instruction manual PDZX7101
Printed instruction
10
0.0~500.0
(written in English) for
manual
11
0.0~600.0
compact controller M (PDC1)
12
-50.0~100.0
-100.0~200.0
14
-200.0~600.0
1
terminal on PLC side
04
13
1
terminal at both ends
03
PDZK6xx1
between PDC and PC
Extension case
1
PC side
between PDC and PLC
For compression terminal
1
terminal at both ends
between PDC and PDC
For compression terminal
With M3.5 solderless
9-pin connector on
1
PC side
PDZE2002
For CC-F replacement
1
Printed instruction manual PDZX6101
Printed instruction
1
(written in Japanese) for
manual
(under development)
compact controller M (PDC1)
Instruction manual in CD-ROM PDZQ1001
CD-ROM version
(common for Japanese and
instruction manual
1
1
English) (Note 3)
Fixture (Note 4)
PDZA1001
Improved fixture
1
(Note 1) Screw terminal type required for using control output and digital
input/output (see Outline Diagram). Prepare separately if needed.
(Note 2) Transmission cable for T-link/Modbus communication.
(Note 3) This CD-ROM contains the instruction manuals written in Japanese and
English.
(Note 4) An improved fixture adopted starting from the PDC-2. For the shape
and dimensions, refer to Outline Diagram.
Block diagram of electrical isolation
Solid line shows
isolation from the
other units or circuits.
Power
supply
Power supply
unit
DI1 to DI10
DI / DO
unit
Ground
PV1
DO1 to DO10
Ground
TC or RTD
input unit
AI / AO
unit
PV2
AI1 to AI6
(Note) AI1 is exclusively used for open-angle input.
AO1 to AO5
Modbus
Communication unit (Note)
(Note) Not isolated from the analog input/output
section in case of T-link.
6
T-link
CODE SYMBOLS
1 2 3 4 5 6 7 8 9 10111213 1415
PDC
2 - 10
1
1
Description
Equipment function <4th digit>
With fixed function
Number of control loops <5th digit>
1 loop (1 control output)
External terminal <6th digit>
M3.5 screw
Compression terminal
1
2
Input signal <7th digit>
1 to 5 V DC (DC4 to 20mA)
Thermocouple : 1
Resistance bulb Pt100 : 1
Resistance bulb JPt100 : 1
A
C
D
E
Note 1
Power supply voltage <9th digit>
100 V to 240 V AC (usable range 85 V to 264 V AC), 50/60 Hz
24 V DC (usable range 20 V to 30 V DC)
A
B
Setting method <10th digit>
C-A-M type
A-M type
R-A-M type
C
A
R
Backup operation unit <11th digit>
None
Y
Communication function/memory card interface <12th digit> Notes 2 and 3
(Slave communication) (Master communication) (Memory card interface)
Without
Without
Without
Without
Without
With
Modbus
Without
Without
Modbus
Without
With
T-link
Without
Without
T-link
Without
With
Y
M
C
U
A
S
Y
C
Instruction manual <13th digit>
None
CD-ROM version instruction manual (common for both Japanese and English) Note 4
Note 1) For current input, conversion into a voltage is required using a shunt resistor.
This resistor is separately available.
Note 2) The communication cable and terminating resistor are separately available.
Note 3) Memory card should be purchased from a dealer such as personal computer shop.
Note 4) The relevant manual is stored in the PDF file format.
For reading the manual, Adobe® Acrobat® Reader is required.
The CD-ROM also contains the Acrobat® Reader setup program.
Input signal and measurable range will meet the following specifications for product delivery.
For specification of voltage input : 0.00 to 100.00% scale
For specification of thermocouple : K thermocouple, measurable range 0.0 to 400.0°C
For specification of resistance bulb : Measurable range 0.0 to 150.0°C with both Pt and JPt
7
PDC1
67.5
OUTLINE DIAGRAM (screw terminal type) (Unit : mm)
Terminal Cover
16
144
137.5
20
Panel
Panel thickness 8mm or less
Covering fixture
72
272
134
100Min
21.6
Fixture
Note) When there is any object like other instrument or floor below the controller, an open space of 100 mm min.
is required between the bottom face of controller and such an object.
67.5
OUTLINE DIAGRAM (compression type) (Unit : mm)
Panel thickness 8mm or less
Terminal Cover
Covering fixture
16
144
137.5
20
Panel
72
280
100Min
21.6
Fixture
Note) When there is any object like other instrument or floor below the controller, an open space of 100 mm min.
is required between the bottom face of controller and such an object.
PANEL CUTOUT DIMENSIONS
68 +0.7
0
8
138
+1
0
250 or more
+1
0
For mounting multiple ”n” units
138
250 or more
For mounting one unit
(72.2
n-4)
+1
0
Number of units
n 2
FIXTURE
16
160
50
205
9
PDC1
EXTERNAL CONNECTION DIAGRAM (Screw terminal type, M3.5 screw section)
ThermoVoltage couple
Resistance
input
input
builb input
(+)
Process
value
input
(−)
Rcj
Voltage
External input
setting
input
VPD
b 11
○
I+1
B 12
○
I-1
A 13
○
Io1
14
I+2
15
I-2
16
Io2
PCD
Note1)
FLT
31
DO1
32
Note1)
51
AO1
52
AO2
DI1
33
53
AO3
DI2
34
54
AO4
VST2
35 Note1)
55
AO5
T1
36 Note1)
56
SC
T2
37 Note1)
57
SC
RS485
communication
(Modbus) or T-link
host communication
Note4)
AI1
71
Note1)
AI2
72
Note1)
AI3
73
Note1)
AI4
74
Note1)
AI5
75
SC
76
MI+1
77
Note1)
78
Note1)
79
Note1)
80
Note1)
58 MOD+ SC
MI-1
59 MODMI+2
60 VST
MI-2
PC
61
VP
62 PCD
VPD
G
63
L/+
64 N/-
(+)
(-)
(COM)
24V external
supply (-)
81
Voltage
input
24V external
supply (+)
82
83
Grounding
∼
Note3) DO1 23
(Same as screw No. 34)
Note3) DO2 24
DO3 25
MI+3 1
Note1)
2
Note1)
MI+4 3
Note1)
DI1 13
(Same as screw No. 33)
MI-3
DI2 14
(Same as screw No. 34)
Instrument power source
100 to 240V AC
or
Instrument power source 24V DC
DO4 26
DI3 15
MI-4
4
DO5 27
DI4 16
AO1
5 (Same as screw No.51)
DO6 28
DI5 17
AO2
6 (Same as screw No.52)
DO7 29
DI6 18
AI1
7 (Same as screw No.71)
DO8 30
DI7 19
AI2
8 (Same as screw No.72)
DI8 20
AI3
9 (Same as screw No.73)
DI9 21
AI4
10 (Same as screw No.74)
SC
11 (Same as screw No.55,57,76)
DO9 31
DO10 32
VPD 33
PCD 34
+
-
24V
(Same as screw No.82)
(Same as screw No.62)
DI10 22
PCD
Note1)
-
+
-
+
24V power source for DIO
PCD 12 (Same as screw No.62)
Note 1) Screw terminals No. 16, 35, 36, 37, 51, 72, 73, 74, 75, 77, 78, 79, 80
and MULTI-CONNECTOR
No. 1, 2, 3, 4 do not used (can't connect).
Note 2) Control output is allocated to MULTI-CONNECTOR No. 23 and 24.
Prepare a mulit-connector (any one below) separately.
PDZC1001
PDZC2001
PDZC3001
PDZC4001
Soldering type straight terminal
Soldering type right-angle terminal
Solderless type straight terminal
Solderless type right-angle terminal
Note 3) Control output should be cross-connected to each other,
externally.
+
M
-
L1
Do1
L2
Do2
Note 4) Connect open-angle input between screw terminals Nos. 71 and
SC or multi-connector pin 7 and 11.
10
EXTERNAL CONNECTION DIAGRAM (Compression terminal type)
Voltage input
24V external supply
(+)
(-)
VPD
PCD
RS485
(+)
communication
(-)
(Modbus) or T-link
host communication (COM)
24V power
for DIO
1
AI1
2
SC
3
AI2
4
AI3
5
SC
6
AI4
7
AI5
8
SC
9
AI6
10
SC
11
VP
12
PC
13
DI9
14 DI10
15 DO9
16 DO10
17 MOD+
18 MOD19 COM
20 VPD
21 PCD
Note3)
Note1)
Note1)
Note1)
Note1)
Note1)
Note1)
Note1)
Note1)
Note1)
Note1)
VPD
Note1)
Note1)
Note1)
Note1)
Note1)
PCD
External
setting
input
Note1)
Note1)
22
MI+2
23
MI-2
24
MI+3
25
MI-3
26
MI+4
27
MI-4
28
DO6
29
DO7
30
DO8
31 DIO-COM
PCD
32
DI6
33
DI7
34 DIO-COM
35
DI8
36 OPT+
37
OPT38
COM
39
I+2
40
Io2
41
Rcj2
42
I-2
Note1) 43
Note1) 44
Note1) 45
VPD
Note1)
Note1)
Note1)
Process
value
input
∼
-
b
A
(−)
B
Voltage Thermoinput
couple
input
G N/- L/+
Grounding
(+)
Rcj
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
MI+1
MI-1
AO1
SC
AO2
AO3
SC
AO4
FLT
DO1 Note2)
DO2 Note2)
DO3
DO4
DO5
DI1
DIO-COM
DI2
PCD
DI3
DIO-COM
DI4
DI5
I+1
Io1
Rcj1
I-1
Resistance
bulb
input
Instrument power source 100 to 240V AC
or
Instrument power source 24V DC
The area enclosed with a dotted
line is the circuit within the main unit.
+
Note 1) Compression terminal No. 3, 4, 6, 7, 9, 22, 23, 24, 25, 26, 27, 32, 36, 37, 38, 40, 41, 43, 44, 45, 60, 62, 63
donot be use (can’t connect).
Note 2) Control output should be cross-connected to each other, externally.
+
M
-
L1
DO1
L2
DO2
Note 3) Cannect open-angle input between compression terminals Nos. 1 and SC.
11
PDC1
[Note] Windows® is the registered trade mark of Microsoft corporation.
[Note] Modbus® is a registered trademark of Schneider Electric Limited.
[Note] Compact Flash® is the registered trade mark of Sandisk corporation.
[Note] Pentium® is the registered trade mark of lntel corporation.
[Note] Adobe® and Acrobat® are trade marks of Adobe Systems Incorporated.
Caution on Safety
*Before using this product, be sure to read its instruction manual in advance.
Head Office
6-17, Sanbancho, Chiyoda-ku, Tokyo 102-0075, Japan
http://www.fesys.co.jp/eng
Instrumentation Div.
International Sales Dept.
No.1, Fuji-machi, Hino-city, Tokyo, 191-8502 Japan
Phone: 81-42-585-6201, 6202 Fax: 81-42-585-6187
http://www.fic-net.jp/eng
Information in this catalog is subject to change without notice.
Printed in Japan