FUJI EDSX11-138B

FC SERIES ELECTRONIC INDICATOR
DATA SHEET
PDJ3
The FC series Indicator is a indicator to be used in a process
and it excels in the effect of monitoring due to adoption of a
color LCD.
Use of two bargraph display has enabled arrangement of
many monitoring points influenced by one another.
Besides standard signals of 1 to 5 V DC, input signals from
thermocouples and resistance bulbs can be handled at option.
FEATURES
1. High visibility ensured with color graphic display
A color LCD is adopted for graphic display of bar graph
and trend screens,etc.
2. Communication function (option)
RS-485 (Modbus protocol) are available.
3. Memory card (option)
Memory card can save any data, for example process input, WAFER output, etc.
Communication
RS-485 (Modbus® )
Transmission terminal
PV1
PV2
indicator indicator
Signal name/terminal No.
Signal name/terminal name
Linearize
Square root
Filter
Indicating input 1/PV1
(analog input)
Square root
Filter
External input terminal
Linearize
Internal input terminal
Internal input terminal
External input terminal
Indicating input 2/PV2
(analog input)
Compensation signal for indication
signal1/AO1
Compensation signal for indication
signal1/AO2
ALM 1
Upper alarm output (H1)/DO7
Lower alarm output (L1)/DO8
ALM 2
Upper alarm output (H2)/DO9
Lower alarm output (L2)/DO10
Fault output (FLT-Do)/FLT
Fault
FLT lamp
EDSX11-138b
Date
Dec. 24, 2003
PDJ3
SPECIFICATIONS
1. Input Signals
Performance under reference condition(23± 2˚C,
55± 10%RH, Power voltage and frequency variation ± 1%,
free from the effect of external noise) unless otherwise
specified.
1-1 Analog input signal
• Number of inputs
8 inputs
• Inpute signal types
: DC voltage, thermocouple (option), resistance bulb (option)
Two thermocouple inputs or two resistance bulb inputs
are selectable.
(1) DC voltage • Input range: Selectable among 0 to 5 V
DC, 1 to 5 V DC and 0 to 10 V DC
Initial set before delivery : 1 to 5 V DC
• Input accuracy: ± 0.1% of input span± 1
digit
• Scaling (Industrial data conversion) :
Settable within a range from -32767 to
32767
4, 3, 2, 1 or 0 digit below decimal point
is selectable.
Initial set before delivery : 0.00% to
100.00%
• Industrial unit: Settable in up to 8 characters
Usable characters: Alphabets numerals,
symbols such as +, – ,*,etc.
• Input accuracy guarantee range: –5% to
105% of input range.
• Maximum continuous permissible voltage: ± 35 V
• Input resistance: 1 MΩ or more
• Influence by ambient temperature:
± 0.1% FS/10°C or less.
• Influence by power supply fluctuation:
± 0.1% FS or less.
• Isolation : Non-isolated from internal circuit.
• In case of current input:
Shunt resistor need to be connected to
the analog input terminal.
(250 Ω shunt resistor is optional item)
(2) Thermocouple (option)
• Types and measurable ranges:
* See Table 2.
• Input accuracy: ± 0.2% FS ± 1 digit
[Note]B type: ± 5% between 0 to 400˚C
S and R type: ±1%between 0 to 500˚C
All type of TC: ± 5% under–100˚C
• Reference junction compensation error:
± 1.0°C (provided measurable range is
–50°C and higher)
[Note]Reference junction compensation resistor is connected at external
input terminal in case of thermocouple input is ordered.
• Input accuracy guarantee range: –5%
to 105% of input range.
• Input resistance: 1 MΩ or more
2
• Allowable signal source resistance:
100 Ω or less (Zener barrier connection
unallowable)
• Influence by signal source resistance:
About 0.25 µV/Ω
• Influence by ambient temperature:
± 0.2% FS/10°C ± 1°C or less.
• Influence by power supply fluctuation:
± 0.2% FS ± 1˚C or less
• Burnout detection: Provided
• Isolation: Isolated from internal circuit.
(3) Resistance bulb (option)
• Types and measurable ranges:
* See Table 2.
• Input accuracy: ± 0.2% FS ± 1 digit
• Input accuracy guarantee range:
-5% to 105% of input range
• Allowable wiring resistance: 10Ω or
less per wire, provided wiring resistance must be equal among 3 wires (Zener barrier connection unallowable)
• Influence by ambient temperature: ± 0.2% FS/10˚C or less.
• Influence by power supply fluctuation:
± 0.2% FS or less
• Burnout detection: Provided
• Isolation: Isolated from internal circuit.
[Note] FS: full span.
• Sampling period
: 100 ms
1-2 Digital input signal
• Number of inputs
: 10 inputs
• Electrical specifications
: No-voltage contact or transistor contact
ON/0 V, OFF/24 V, ON current/about 8
mA
Isolated from the internal circuit by
photocoupler. Not isolated between
each digital input and output.
• Contact rating : 30 V DC, 10 mA or more
• Signal judgment
: No-voltage contact
Contact resistance;
200 Ω or less at ON,
100 kΩ or more at OFF
: Transistor contact
1V max at ON.,
leakage current 100µA max. at OFF
2. Output Signals
Performance under reference condition(23± 2˚C,
55± 10%RH, Power voltage and frequency variation ± 1%,
free from the effect of external noise) unless otherwise
specified.
2-1 Analog output signal
(1) Auxiliary analog output
• Number of outputs:
: 4 outputs
• Types of signal : Selectable among 0 to 5 V DC, 1 to 5 V
DC and 0 to 10 V DC
Initial set before delivery: 1 to 5 V DC
• Output accuracy
: ± 0.1% FS
• Load resistance
: 15 kΩ or more
• Output guarantee range
: 1 to 5 VDC : –12.5% to 112.5%
: 0 to 5 VDC : 0% to 112.5%
: 0 to 10VDC : 0% to 105%
• Influence by power supply fluctuation
: ± 0.1% FS or less
: Non-isolated from internal circuit
•Isolation
2-2 Digital output signal
• Number of outputs
: 10 outputs
• Electrical specifications
: Transistor open collector
1 V max. at ON, 10 µA max at OFF.
Isolated from the internal circuit by
photocoupler. Not isolated between
each digital input and output.
• Output rating : 30 V DC, 100 mA max. (resistive load)
2-3 Fault output signal (terminal symbol FLT)
• Number of outputs
: 1 output
• Electrical specifications
: Transistor open collector
1 V max. at ON, 10 µA max at OFF.
Isolated from the internal circuit by
photocoupler. Not isolated between
each digital input and output.
• Output rating : 30 V DC, 100 mA max. (resistive load)
4. Operation
(1) Security
• Method
• Password
: Setting of a password
: Settable in 4 numerals (within 0000 to
ffff)
Initial set before delivery: 0000
• Contents of security
: Inhibition of parameter setting
(2) Other setting items
• Tag name
: Settable in up to 8 characters
Usable characters; alphabes, numerals,
symboles such as +, – ,*,etc.
5. Power Supply
• Voltage rating : 100 V to 240 V AC/24 V DC
• Allowable range
: 85 V to 264 V AC/20 V to 30 V DC
• Frequency
: 47 to 63 Hz
• Power consumption
: 60 VA or less (100 V to 240 V AC)
: 30 W or less (24 V DC)
• Power supply output voltage
(terminal symbol VP and PC)
: 20V to 30V DC,max. 40mA
3. Display
• Display unit
: 16 Colors graphic liquid crystal display,
with CFL back light and contrast adjust
function.
• Contents of display
: Menu
: Loop panel (1 and 2 loops)
Bar graph display, digital display, etc.
: Trend screen (max. 8 screens)
: Alarm and alarm historical screen
: Analog input/output and digital input/
output indication screen
: WAFER connection screen
: Parameter setting screen
3
PDJ3
6. General performance and characteristics
• Insulation resistance
: 500 V DC, 50 MΩ or more.
• Dielectric strength
: 2,000 V AC for 1 minute between
power terminal and ground terminal in
case of 100 V to 240 V AC power supply
: 500 V AC for 1 minute between power
terminal and ground terminal in case of
24 V DC power supply.
: 500 V AC for 1 minute between signal
communication terminals and ground
terminal
• Rush current : 60 A or less. (100 V AC to 240 V AC
power supply)
• Clock
: Set and display year, month, day, hour,
minute, second
accuracy : ± 100 ppm except of time lag
shorter than 1 s / power ON / OFF action.
• Memory backup
: Protection by lithium battery.
(expected battery life is about 2 years
under room temperature)
Parameter and program are stored nonvolatile memory.
7. Operating and storage conditions
• Operating temperature
: 0 to 50˚C
: 0 to 40°C in case of multiple mounting
( Temperature change rate : Max. 10˚C / h)
• Transport and storage temperature
: -20 to 70˚C
( Temperature change rate : Max. 20˚C / h)
• Operating humidity
: 5 to 90% RH, condensation unallowable
• Transport and storage humidity
: 5 to 95% RH, condensation unallowable
• Operating continuous vibration
: 4.9 m/s2 or less
• Transport and storage shock
: Fall of 60cm max. in packed status
8. Power Failure and restart Function
• Permissible duration of momentary power failure
: 20 ms at 90V AC (100 V to 240 V AC
only)
[Note] In case of 24 V DC, system power supply unit
(model: PXJ) is recommended to avoid power
failure problem.
• Behavior at power failure detection
: Control stops at detection of power failure.
• Power recovery mode
: Selectable initial start and continuous
start
4
9. Self-Diagnosis
• Control and computation circuit failure
: Monitoring with watchdog timer
• Input signal failure
: Voltage/current input
Monitoring of range over
: Thermocouple and resistance bulb
Monitoring of disconection
• Behavior at failure
: FLT is indicated, FLT lamp lights, and
FLT output signal turns on.
10. Structure
• Enclosure
: Plastic (material: PC-ABS)
• Finish color
: Front frame and enclosure both gray
• Flame resistance
: UL94V-0
• Protection
: Front face; IP54 (display unit and operation key)
• External dimensions (W x H x D)
: 72 x 144 x 280 mm
• Mass
: 1.9 kg or less
• Mounting method
: Flush on indoor panel
Vertical mounting as standard
Tilted mounting allowed within backward angle 0° to 45°.
90° to 45°
For panel cutout dimension, refer to
Panel Cutout Dimensions
• External terminal
: Compression terminal type
11. Communications (option)
11-1 RS485 interface-1
• Communication behavior
: Slave
• Communication protocol
: Modbus® protocol
• Physical specification
: EIA RS-485
• Communication method
: Half-duplex, bit serial
: Start-stop synchronizing
• Connection form
: Multi-drop
• Communication speed
: 19.2 kbps
• Communication distance
: Max. 500 m in total
• Number of connectable units
: Max. 31 units
: Fixed to 8 bits
• Data length
: Odd / Even / None
• Parity
: 1 or 2
• Stop bit
: Isolated from internal circuit
• Isolation
: 100 Ω (optional item)
• Terminator
• Communication items
: Parameters and process value.
• RS232C / RS485 signal converter (optional item)
: Code symbol: PDZT0001
12. Memory Card Interface (option)
• Specification : Compact Flash® (Based on CFA)
• Compatible memory card
: 5 V flash memory card
Capacity 4, 20 and 32 MB
: Process data logging (32 points or less)
• Application
• Saving period : 1s to 2h
• Data storage capacity
Memory card
capacity
Data storge
4MB
about 180 thousand data
20MB
about 900 thousand data
32MB
about 1.35 million data
[Note] The data of max. 16 points (4 screens) can be
storaged at storage time as 1 s.
• Format method
: Dependent on this indicator
• Data readout : Readout by PC using PCMCIA card slot
• Recommended memory card
: Made by Sandisk corporation
Sandisk compact Flash memory card is
standardized and on the market.
13. Standards under Conformity
(1) General safety
: IEC 1010-1 (1990)
EN 61010-1 (1993)
(2) EMC
: Emission EN 50081-2 (1994)
Immunity EN 50082-2 (1995)
5
PDJ3
Table 1
List of WAFERS
WAFER name
Bit concatevate
Kinds
Outline
8
Outputs digital data as word data to
an external expansion I/O.
Bit slicing
Slices the digital data acquired as
1
word data from an external
expansion I/O into each bit.
1
Encoder
Encodes an input signal into
a binary code.
1
Sawtooth wave generator
Generates a sawtooth wave with
a slope entered for each
cycle time.
5
BCD
Converts BCD data into binary data
and binary data into BCD data.
Logical operation
Carries out AND,OR,NOT,XOR
6
and a combination of these logical
operations.
Carries out a combination of
Arithmetic operation
8
addition,subtraction,multiplication
and division.
Carries out temperature and
Temperature/pressure
1
pressure compensation through use
compensation
of differential pressure,compensated
pressure,proper temperature.
Linearize
7
Carries out segmented-line
approximation with 15-segmentedline function.
1
Flip-flop
RS flip-flop.
Adds the change of input at each
1
Pulse width integration
basic cycle to the previous
integration value.
Selector
Compares two input values,and
1
provides High output(Large one),
Low output(Small one),and result
of judgement on large/small.
Selects input or output via a switch
1
Changeover
function.Analog hold circuit also
provided.
Outputs on-delay,off-delay timer
1
Timer
signal via start of input signal
according to timer setting.
Carries out absolute value processing
1
Absolute value/sign
on input and outputs the result.Also
inversion
judges the sign(Positive,negative)of
input value and outputs the result.
Extracts square root of input value
1
Square root extraction
and outputs the result.Low input
cutoff function equipped.
Carries out lead/lag operation on the
3
Lead,lag
input and outputs the results.
Used as analog filter function and
for various compensations.
Limits the input within the range of
1
Limiter
high/low limit settings,and outputs
the result.Also outputs high/low
limit alarm signal.
Outputs signal which changes...in
2
Ramp function
ramp from toward target value at
the set full scale time.There are two
of these wafers...in minute unit and
hour unit.
Carries out sequential integration on
1
Analog averaging
input data,calculates the average
value at each averaging time,
and otuputs the result.
Integrates the value obtained by
1
Analog integration
multiplying the input data by
a proportional constant,and outputs
the result.
Outputs a pulse at the set time
1
Pulse generation
interval.
Adds dead band compensation to
1
Dead band
the input and outputs the result.
6
WAFER name
Pulse No.counter
Pulse No.output
Decoder
Running average
Sample & hold
Dead time
ON-OFF
Alarm
Palse width modurator
Kinds
Outline
1
Detects rise of pulse and counts the
number of pulses.
Integrates the input signal and
1
converts it to number of pulses
for output.
Decodes 2-bit pure binary input and
1
outputs it to 4 terminals.
Calculates ranning average of input
2
data and outputs the result.
Holds the input value according to
1
sample signal(0/1)and continues
the output.
Usable for dead time compensation
6
control etc.Data sampling can be
done in 1 sec or 1 min units.
Outputs ON-OFF signal with
1
hysteresis.
Compares the input and set value
1
and outputs the judgment result.
1
Performs output processing in time
proportional PID control.
A variety of applications are possible through combination of WAFERS.
Table 2
SCOPE OF DELIVERY
List of Thermocouple and Resistance Bulb Measurable
range
Input signal
Thermocouple
Indicator, panel mounting bracket, instruction manual
(depend on code symbols)
Input type code Input range code Measurable range˚C
J
00
0.0~400.0
J
01
01
0.0~800.0
K
02
0.0~400.0
K
03
0.0~800.0
Optional Items
Specificatio
Available
unit
PDZR2001
For compression terminal
1
PDZS2001
For compression terminal
1
1
Item
Terminator
Type
K
04
0.0~1200.0
for communication (100 Ω)
R
05
0.0~1600.0
Shunt resistor (250 Ω)
B
06
0.0~1800.0
Communication cable (Note1)
T
07
-200.0~200.0
For compression terminal, PDZK4xx1
With compression
from PD* to PD*
terminal at both ends
For compression terminal, PDZK5xx1
With M3.5 solderless
terminal on PLC side
9-pin connector on PC side
1
RS232C / RS485
1
T
08
-150.0~400.0
E
09
0.0~800.0
E
10
-200.0~800.0
from PD* to PLC
S
11
0.0~1600.0
For compression terminal, PDZK6xx1
N
12
0.0~1300.0
from PD* to PC
U
13
-200.0~400.0
Communication converter PDZT0001
signal converter
WRe5-26
14
0.0~2300.0
PL2
15
0.0~1300.0
Electronic Indicator
00
0.0~150.0
Instruction Manual
01
0.0~300.0
in book form (in English)
02
0.0~500.0
Instruction Manual on
0.0~600.0
CD-ROM (in English)
Resistance bulb Pt100
00
03
04
-50.0~100.0
05
-100.0~200.0
06
-200.0~600.0
07
-200.0~850.0
1
Mounting bracket
Instruction manual in
PDZX3J01
book form
1
PDZQ2001
Instruction manual on
CD-ROM
1
PDZA1001
Improved mounting
1
bracket
(Note 1) These cables are used for Modbus.
Length needs to be specified.
Block diagram of electrical isolation
Solid line shows
isolation from the
other units or circuits.
Power
supply
Power supply
unit
DI1 to DI10
DI / DO
unit
Ground
PV1
PV2
RS485
(Modbus)
DO1 to DO10
Ground
TC or RTD
input unit
AI / AO
unit
TC or RTD
input unit
AI1 to AI6
AO1 to AO4
Communication unit
7
PDJ3
CODE SYMBOLS
1 2 3 4 5 6 7 8 9 10111213 1415
PDJ 3 1
1 - YY
- Y
Description
External terminal <6th digit code>
Compression terminal
2
Input signal <7th digit code>
1 to 5 V DC
Thermocouple
Resistance bulb Pt100
A
C
D
Note 1
Note 2
Note 2
Power supply voltage <9th digit code>
100V to 240V AC (Usable range 85V to 264V AC) 50 / 60Hz
24V DC (Usable range 20 to 30V DC)
A
B
Communicatioin / Memory card interface <12th digit code>
(Slave)
(Master)
(memory card interface) Note 3 Note 4
Without
Without
Without
Without
Without
With
RS485
Without
Without
Note 5
RS485
Without
With
Note 5
Y
M
C
U
Instruction manual <13th digit code>
Without
With Instruction Manual on CD-ROM (in Japanese and English)
Y
D
Y
B
Input range designation <14th digit code>
Without
With
Note 6
Note 1) For current input, a shunt resistor is used for conversion into voltage.
Shunt resistor is optional item.
Note 2) Thermocouple and resistance bulb input are opitons.
Allowable up to 2 points.
Note 3) Communication cable and terminator are optional items.
Note 4) Recommended maker: Sandisk corporation.
Note 5) Slave interface is Modbus protocol.
Note 6) Input range designations need to be prepared and submitted by user to fuji.
If not (code "Y") , input signal and measurable range initial set before delibvery
is as follows.
For specification of voltage input, scale is 0.00 to 100.00%
For specification of thermocouple, K, 0.0 to 400.0˚C.
For specification of resistance bulb is 0.0 to 150.0˚C.
8
67.5
OUTLINE DIAGRAM (Unit : mm)
Panel thickness 8mm or less
Terminal cover
Mounting bracket
144
137.5
20
Panel
21.6
100MIN.
72
280
Mounting bracket
Note) The distance between other instruments and low end of PDJ shall be more than 100mm.
MOUNTING BRACKET
16
160
50
205
PANEL CUTOUT DIMENSIONS
For mounting
multiple "n" units
250 or more
250 or more
For mounting
one unit
68
138
138 0
+1
+1
0
Number of
+0.7
0
(72.2n-4)
units n
2
+1
0
9
PDJ3
EXTERNAL CONNECTION DIAGRAM
Voltage
input
24 V external
Power supply
RS-485
(Modbus)
(+)
(–)
(+)
(–)
(COM)
24 V
Power
supply
for DIO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
AI1
SC
AI2
AI3
SC
AI4
AI5
SC
AI6
SC
VP
PC
DI9
DI10
DO9
DO10
MOD+
MODCOM
VPD
PCD
PCD
22
MI+2
23
MI-2
24
MI+3
25
MI-3
26
MI+4
27
MI-4
28
DO6
29
DO7
30
DO8
31 DIO-COM
VPD
32
DI6
33
DI7
34 DIO-COM
35
DI8
36
OPT+
37
OPT38
COM
(+)
I+2
b 39
Rcj
Process
Io2
A 40
variable
41
Rcj2
(–)
input 2
B 42
I-2
Voltage Thermo- Resistance
bulb
input
couple
input
input
VPD
PCD
(+)
Process
variable
input 1
Rcj
(–)
b
A
B
43
MI+1
44
MI-1
45
AO1
46
SC
47
AO2
48
AO3
49
SC
50
AO4
51
FLT
52
DO1
53
DO2
54
DO3
55
DO4
56
DO5
57
DI1
58 DIO-COM
59
DI2
60
DI3
61 DIO-COM
62
DI4
63
DI5
64
I+1
65
Io1
66
Rcj1
I-1
67
Voltage Thermo- Resistance
bulb
input
couple
input
input
G N/– L/+
Power source 100 to 240V AC
~
Power source 24V DC
–
+
INPUT/OUTPUT TERMINAL FUNCTION (when preset WAFER)
Input terminal
Output signal name
Output terminal
Indicating input 1 (PV1)
Input signal name
I+1,I-1
Compensation signal for indicating input 1
AO1
Indicating input 2 (PV2)
I+2,I-2
Compensation signal for indicating input 2
AO2
Universal analog input
AI1
Universal analog output
AO3
Universal analog input
AI2
Universal analog output
Universal analog input
AI3
Don't use
MI+1,MI-1
Universal analog input
AI4
Don't use
MI+2,MI-2
Universal analog input
AI5
Don't use
MI+3,MI-3
Universal analog input
AI6
Don't use
MI+4,MI-4
Universal digital input
DI1
Universal digital output
DO1
Universal digital input
DI2
Universal digital output
DO2
Universal digital input
DI3
Universal digital output
DO3
Universal digital input
DI4
Universal digital output
DO4
Universal digital input
DI5
Universal digital output
DO5
Universal digital input
DI6
Universal digital output
DO6
Universal digital input
DI7
Upper alarm output (H)
DO7
Universal digital input
DI8
Lower alame output (L)
DO8
Universal digital input
DI9
Upper alarm output (H)
DO9
Universal digital input
DI10
Lower alame output (L)
DO10
AO4
Analog
Digital
Fault output (FLT-DO)
10
FLT
Don't use
OPT+
Don't use
OPT-
PCD
11
PDJ3
[Note] Windows is the registered trade mark of Microsoft corporation.
[Note] Modbus is the registered trade mark of Gould Modicon.
[Note] Compact Flash is the registered trade mark of Sandisk corporation.
Caution on Safety
*Before using this product, be sure to read its instruction manual in advance.
Head Office
6-17, Sanbancho, Chiyoda-ku, Tokyo 102-0075, Japan
http://www.fesys.co.jp/eng
Sales Div.
International Sales Dept.
No.1, Fuji-machi, Hino-city, Tokyo, 191-8502 Japan
Phone: 81-42-585-6201, 6202 Fax: 81-42-585-6187
http: //www.fic-net.jp/eng
Information in this catalog is subject to change without notice.
Printed in Japan