W005G THRU W10G GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 1.5 Amperes FEATURES Case Style WOG ♦ Plastic material has Underwriters Laboratory Flammability Recognition 94V-0 ♦ This series is UL listed under the Recognized Component Index, file number E54214 ♦ Glass passivated chip junctions ♦ High case dielectric strength ♦ Typical IR less than 0.1µA ♦ High overload surge capability ♦ Ideal for printed circuit boards ♦ High temperature soldering guaranteed: 260°C/10 seconds, 0.375” (9.5mm) lead length, 5lbs (2.3kg) tension 0.388 (9.86) 0.348 (8.84) 0.220 (5.6) 0.160 (4.1) 1.0 (25.4) MIN. 0.032 (0.81) 0.060 (1.52) 0.028 (0.71) 0.020 (0.51) MECHANICAL DATA 0.220 (5.6) 0.348 (8.84) 0.180 (4.6) Case: Molded plastic body over passivated junctions Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Mounting Position: Any Weight: 0.04 ounce, 1.1 grams 0.308 (7.82) 0.220 (5.6) 0.180 (4.6) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS W005G W01G W02G W04G W06G W08G W10G UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current at 0.375" (9.5mm) lead length at T A=25°C I(AV) 1.5 Amps Peak forward surge current single sine-wave superimposed on rated load (JEDEC Method) IFSM 50.0 Amps Rating for fusing (t<8.3ms) I2t 10.0 A2sec Maximum instantaneous forward voltage drop per leg at 1.0A VF 1.0 Volts Maximum DC reverse current at rated TA=25°C DC blocking voltage per leg TA=125°C IR 5.0 500.0 µA Typical junction capacitance per leg (NOTE 1) CJ 14.0 pF RΘJA RΘJL 36.0 11.0 °C/W TJ -55 to +150 °C TSTG -55 to +150 °C Typical thermal resistance per leg (NOTE 2) Operating junction temperature range Storage temperature range NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Thermal resistance from junction to ambient and from junction to lead at 0.375" (9.5mm) lead length P.C.B. mounting 4/98 RATINGS AND CHARACTERISTICS CURVES W005G THRU W10G FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG AVERAGE FORWARD OUTPUT CURRENT, AMPERES 1.6 60 HZ RESISTIVE OR INDUCTIVE LOAD 1.4 1.2 0.375” (9.5mm) P.C.B. 1.0 0.22 x 0.22” (5.5 x 5.5mm) COPPER PADS 0.8 0.6 0.4 CAPACITIVE LOADS Ipk/IAV=5.0 Ipk/IAV=10 Ipk/IAV=20 PEAK FORWARD SURGE CURRENT, AMPERES FIG.1 - DERATING CURVE OUTPUT RECTIFIED CURRENT 0.2 60 TA=25°C SINGLE SINE-WAVE (JEDEC Method) 50 40 30 20 10 1.0 CYCLE 0 10 1 0 20 100 NUMBER OF CYCLES AT 60 HZ 40 60 80 100 120 140 150 AMBIENT TEMPERATURE, °C FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG FIG. 3 - TYPICAL FORWARD CHARACTERISTICS PER LEG 50 20 TJ = 25°C PULSE WIDTH=300µs 1% DUTY CYCLE INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 1 0.1 10 TJ=100°C 1 0.1 TJ=25°C 0.01 0.4 0.6 0.8 1.0 1.2 1.4 0.01 0 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG TJ=25°C f=1.0 MHz Vsig=50mVp-p 10 1 0.1 1 10 REVERSE VOLTAGE, VOLTS 40 60 80 100 FIG. 6 -TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, °C/W JUNCTION CAPACITANCE, pF 100 20 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 100 100 10 1 0.1 0.01 0.1 1 t, HEATING TIME, sec. 10 100