MAXIM MAX7033_1109

19-3273; Rev 3; 9/11
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
The MAX7033 fully integrated low-power CMOS superheterodyne receiver is ideal for receiving amplitudeshift-keyed (ASK) data in the 300MHz to 450MHz
frequency range. The receiver has an RF input signal
range of -114dBm to 0dBm. With few external components and a low-current power-down mode, it is ideal
for cost-sensitive and power-sensitive applications typical in the automotive and consumer markets. The
MAX7033 consists of a low-noise amplifier (LNA), a fully
differential image-rejection mixer, an on-chip phaselocked loop (PLL) with integrated voltage-controlled
oscillator (VCO), a 10.7MHz IF limiting amplifier stage
with received-signal-strength indicator (RSSI), and analog baseband data-recovery circuitry. The MAX7033
also has a discrete one-step automatic gain control
(AGC) that reduces the LNA gain by 35dB when the RF
input signal exceeds -62dBm. The AGC circuitry offers
an externally controlled hold feature.
The MAX7033 is available in 28-pin TSSOP and
32-pin TQFN packages and is specified over the
extended (-40°C to +105°C) temperature range.
Features
o Optimized for 315MHz or 433MHz Band
o Operates from Single +3.3V or +5.0V Supplies
o High Dynamic Range with On-Chip AGC
o AGC Hold Circuit
o 1ms AGC Release Time
o Selectable Image-Rejection Center Frequency
o Selectable x64 or x32 fLO/fXTAL Ratio
o Low 5.2mA Operating Supply Current
o < 3.5µA Low-Current Power-Down Mode for
Efficient Power Cycling
o 250µs Startup Time
o Built-In 44dB RF Image Rejection
o Better than -114dBm Receive Sensitivity
o -40°C to +105°C Operation
Applications
Automotive Remote
Keyless Entry
Security Systems
Home Automation
Garage Door Openers
Remote Controls
Local Telemetry
Wireless Sensors
Typical Application Circuit appears at end of data sheet.
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX7033EUI+
-40°C to +105°C
28 TSSOP
MAX7033ETJ+
-40°C to +105°C
32 TQFN-EP*
+Denotes a lead(Pb)-free/RoHS-compliant package.
*EP = Exposed pad.
25 DATAOUT
AGND 5
LNAOUT 6
MAX7033
AVDD
XTAL1
XTAL2
SHDN
PDOUT
N.C.
29
28
27
26
25
26 PDOUT
LNASRC 4
LNAIN
27 SHDN
LNAIN 3
30
28 XTAL2
AVDD 2
LNASRC
+
XTAL1 1
31
TOP VIEW
32
Pin Configurations
+
N.C.
1
24
DATAOUT
24 VDD5
AGND
2
23
VDD5
23 DSP
LNAOUT
3
22
DSP
AVDD 7
22 DFFB
AVDD
4
21
N.C.
MIXIN1 8
21 OPP
MIXIN1
5
20
DFFB
MIXIN2 9
20 DSN
MIXIN2
6
19
OPP
AGND 10
19 DFO
AGND
7
18
DSN
IRSEL 11
18 IFIN2
IRSEL
8
17
DFO
MIXOUT 12
17 IFIN1
13
14
15
16
N.C.
XTALSEL
IFIN1
IFIN2
12
11
DVDD
AC
9
TSSOP
10
15 AC
DGND
16 XTALSEL
DVDD 14
MIXOUT
DGND 13
MAX7033
TQFN
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX7033
General Description
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
ABSOLUTE MAXIMUM RATINGS
VDD5 to AGND.......................................................-0.3V to +6.0V
AVDD to AGND .....................................................-0.3V to +4.0V
DVDD to DGND .....................................................-0.3V to +4.0V
AGND to DGND.....................................................-0.1V to +0.1V
IRSEL, DATAOUT, XTALSEL,
AC, SHDN to AGND .............................-0.3V to (VDD5 + 0.3V)
All Other Pins to AGND ..........................-0.3V to (VDVDD + 0.3V)
Continuous Power Dissipation (TA = +70°C)
28-Pin TSSOP (derate 12.8mW/°C above +70°C) ..1025.6mW
32-Thin QFN (derate 21.3mW/°C above +70°C) ....1702.1mW
Operating Temperature Range .........................-40°C to +105°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-60°C to +150°C
Lead Temperature (soldering 10s) ..................................+300°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS (+3.3V OPERATION)
(Typical Application Circuit, VAVDD = VDVDD = VDD5 = +3.0V to +3.6V, no RF signal applied, TA = -40°C to +105°C, unless otherwise
noted. Typical values are at VAVDD = VDVDD = VDD5 = +3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Supply Voltage
VAVDD,
VDVDD
Supply Current
IDD
Shutdown Supply Current
ISHDN
Input-Voltage Low
VIL
Input-Voltage High
VIH
Input Logic Current High
IIH
CONDITIONS
MIN
TYP
MAX
UNITS
+3.3V nominal supply voltage
3.0
3.3
3.6
V
fRF = 315MHz
5.2
6.23
fRF = 433MHz
5.7
6.88
fRF = 315MHz
2.6
fRF = 433MHz
3.5
V SHDN = VDVDD
V SHDN = 0V,
VXTALSEL = 0V
0.4
VDVDD
- 0.4
fRF = 375MHz, VIRSEL = VDD5/2
DATAOUT Output-Voltage High
VOL
VOH
V
μA
VDD5 0.4
VDD5 1.0
1.1
fRF = 315MHz, VIRSEL = 0V
DATAOUT Output-Voltage Low
μA
V
10
fRF = 433MHz, VIRSEL = VDD5
Image-Reject Select Voltage
(Note 2)
8.0
mA
V
0.4
ISINK = 10μA
ISOURCE = 10μA
0.125
V
VDVDD
- 0.125
V
DC ELECTRICAL CHARACTERISTICS (+5.0V OPERATION)
(Typical Application Circuit, VDD5 = +4.5V to +5.5V, no RF signal applied, TA = -40°C to +105°C, unless otherwise noted. Typical
values are at VDD5 = +5.0V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
+5.0V nominal supply voltage
4.5
5.0
5.5
V
Supply Voltage
VDD5
Supply Current
IDD
V SHDN = VDD5
ISHDN
V SHDN = 0V,
VXTALSEL = 0V
Shutdown Supply Current
Input-Voltage Low
2
fRF = 315MHz
5.2
6.4
fRF = 433MHz
5.7
6.76
fRF = 315MHz
3.7
fRF = 433MHz
4.2
VIL
_______________________________________________________________________________________
9.8
0.4
mA
μA
V
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
(Typical Application Circuit, VDD5 = +4.5V to +5.5V, no RF signal applied, TA = -40°C to +105°C, unless otherwise noted. Typical
values are at VDD5 = +5.0V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Input-Voltage High
VIH
Input Logic Current High
IIH
CONDITIONS
TYP
MAX
VDD5 0.4
fRF = 375MHz, VIRSEL = VDD5/2
UNITS
V
15
fRF = 433MHz, VIRSEL = VDD5
Image-Reject Select Voltage
(Note 2)
MIN
μA
VDD5 0.4
VDD5 1.5
1.1
fRF = 315MHz, VIRSEL = 0V
V
0.4
DATAOUT Output-Voltage Low
VOL
ISINK = 10μA
0.125
V
DATAOUT Output-Voltage High
VOH
ISOURCE = 10μA
VDD5 0.125
V
AC ELECTRICAL CHARACTERISTICS
(Typical Application Circuit, VAVDD = VDVDD = VDD5 = +3.0V to +3.6V, all RF inputs are referenced to 50Ω, fRF = 315MHz,
TA = -40°C to +105°C, unless otherwise noted. Typical values are at VAVDD = VDVDD = VDD5 = +3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
GENERAL CHARACTERISTICS
Startup Time
tON
Receiver Input Frequency
fRF
Maximum Receiver Input Level
Time for valid signal detection after V SHDN
= VDVDD
300
Modulation depth >18dB
Sensitivity (Note 3)
Maximum Data Rate
μs
450
0
Average carrier power level
-120
Peak power level
-114
LNA gain from low to high
AGC Hysteresis
250
MHz
dBm
dBm
8
dB
Switching time from low to high gain
1
ms
Manchester coded
33
NRZ coded
66
kbps
LNA IN HIGH-GAIN MODE
1 - j3.4
fRF = 375MHz
1 - j3.9
fRF = 315MHz
1 - j4.7
ZIN_LNA
1dB Compression Point
P1dBLNA
-22
dBm
IIP3LNA
-12
dBm
-80
dBm
3
dB
Input-Referred 3rd-Order
Intercept
LO Signal Feedthrough to
Antenna
Noise Figure
NFLNA
Normalized to 50Ω
fRF = 433MHz
Input Impedance
_______________________________________________________________________________________
3
MAX7033
DC ELECTRICAL CHARACTERISTICS (+5.0V OPERATION) (continued)
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
AC ELECTRICAL CHARACTERISTICS (continued)
(Typical Application Circuit, VAVDD = VDVDD = VDD5 = +3.0V to +3.6V, all RF inputs are referenced to 50Ω, fRF = 315MHz,
TA = -40°C to +105°C, unless otherwise noted. Typical values are at VAVDD = VDVDD = VDD5 = +3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
LNA IN LOW-GAIN MODE
Input Impedance
1dB Compression Point
Input-Referred 3rd-Order
Intercept
ZIN_LNA
Normalized to 50Ω
(Note 4)
fRF = 433MHz
1 - j3.4
fRF = 375MHz
1 - j3.9
fRF = 315MHz
1 - j4.7
P1dBLNA
-10
dBm
IIP3LNA
-7
dBm
-80
dBm
3
dB
35
dB
IIP3MIX
-18
dBm
ZOUT_MIX
330
Ω
16
dB
LO Signal Feedthrough to
Antenna
Noise Figure
NFLNA
Voltage-Gain Reduction
AGC enabled (depends on tank Q)
MIXER
Input-Referred 3rd-Order
Intercept
Output Impedance
Noise Figure
NFMIX
Image Rejection
(Not Including LNA Tank)
LNA/Mixer Voltage Gain
fRF = 433MHz, VIRSEL = VDVDD
42
fRF = 375MHz, VIRSEL = VDVDD/2
44
fRF = 315MHz, VIRSEL = 0V
44
LNA in high-gain
mode
48
LNA in low-gain
mode
13
330Ω IF filter load
dB
dB
INTERMEDIATE FREQUENCY (IF)
Input Impedance
Operating Frequency
ZIN_IF
fIF
Bandpass response
3dB Bandwidth
RSSI Linearity
RSSI Dynamic Range
RSSI Level
AGC Threshold
330
Ω
10.7
MHz
10
MHz
±0.5
dB
80
dB
PRFIN < -120dBm
1.15
PRFIN > 0dBm, AGC enabled
2.2
LNA gain from low to high
1.39
LNA gain from high to low
1.98
V
V
DATA FILTER
Maximum Bandwidth
50
kHz
100
kHz
DATA SLICER
Comparator Bandwidth
4
_______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
(Typical Application Circuit, VAVDD = VDVDD = VDD5 = +3.0V to +3.6V, all RF inputs are referenced to 50Ω, fRF = 315MHz,
TA = -40°C to +105°C, unless otherwise noted. Typical values are at VAVDD = VDVDD = VDD5 = +3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Maximum Load Capacitance
CONDITIONS
MIN
CLOAD
TYP
MAX
UNITS
10
pF
Output High Voltage
VDD5
V
Output Low Voltage
0
V
CRYSTAL OSCILLATOR
VXTALSEL = 0V
fRF = 433MHz
Crystal Frequency (Note 5)
6.6128
VXTALSEL = VDD5
fXTAL
fRF = 315MHz
13.2256
VXTALSEL = 0V
4.7547
VXTALSEL = VDD5
9.5094
Crystal Tolerance
Input Capacitance
From each pin to ground
MHz
50
ppm
6.2
pF
Note 1: 100% tested at TA = +25°C. Guaranteed by design and characterization over temperature.
Note 2: IRSEL is internally set to 375MHz IR mode. It can be left open when the 375MHz image-rejection setting is desired. Bypass
to AGND with a 1nF capacitor in a noisy environment.
Note 3: BER = 2 x 10-3, Manchester encoded, data rate = 4kbps, IF bandwidth = 280kHz.
Note 4: Input impedance is measured at the LNAIN pin. Note that the impedance includes the 15nH inductive degeneration connected from the LNA source to ground. The equivalent input circuit is 50Ω in series with 2.2pF.
Note 5: Crystal oscillator frequency for other RF carrier frequency within the 300MHz to 450MHz range is (fRF - 10.7MHz)/64 for
XTALSEL = 0V, and (fRF - 10.7MHz)/32 for XTALSEL = VDD5.
Typical Operating Characteristics
(Typical Application Circuit , VAVDD = VDVDD = VDD5 = +3.3V, fRF = 315MHz, TA = +25°C, unless otherwise noted.)
+85°C
5.2
5.0
4.8
4.6
+25°C
-40°C
MAX7033 toc02
+105°C
6.0
5.5
5.0
+85°C
+25°C
4.0
4.4
4.2
6.5
4.5
3.2
3.3
1
fRF = 315MHz
0.1
-40°C
0.01
3.0
3.1
fRF = 433MHz
10
3.5
4.0
3.0
100
BIT-ERROR RATE (%)
SUPPLY CURRENT (mA)
+105°C
SUPPLY CURRENT (mA)
5.8
5.4
7.0
MAX7033 toc01
6.0
5.6
BIT-ERROR RATE
vs. AVERAGE CARRIER POWER
SUPPLY CURRENT
vs. RF FREQUENCY
MAX7033 toc03
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
3.4
SUPPLY VOLTAGE (V)
3.5
3.6
250
300
350
400
RF FREQUENCY (MHz)
450
500
-130 -128 -126 -124 -122 -120 -118 -116 -114
AVERAGE CARRIER POWER (dBm)
_______________________________________________________________________________________
5
MAX7033
AC ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics (continued)
(Typical Application Circuit , VAVDD = VDVDD = VDD5 = +3.3V, fRF = 315MHz, TA = +25°C, unless otherwise noted.)
2.2
2.0
3.5
2.2
2.5
2.0
1.5
1.8
0.5
-116
RSSI (V)
fRF = 433MHz
-114
RSSI (V)
1.8
VAC = 0V
1.6
1.6
1.4
-120
-1.5
1.4
fRF = 315MHz
RSSI
1.2
-122
-15
10
35
60
85
-80
-60
-40
-20
0
-90
-70
-50
-30
TEMPERATURE (°C)
RF INPUT POWER (dBm)
IF INPUT POWER (dBm)
LNA/MIXER VOLTAGE GAIN
vs. IF FREQUENCY
IMAGE REJECTION
vs. RF FREQUENCY
IMAGE REJECTION
vs. TEMPERATURE
35
IMAGE REJECTION (dB)
45
49dB IMAGE
REJECTION
25
LOWER
SIDEBAND
15
FROM RFIN
TO MIXOUT
fRF = 315MHz
5
10
15
20
IF FREQUENCY (MHz)
25
45
40
fRF = 375MHz
fRF = 315MHz
fRF = 433MHz
30
fRF = 315MHz
44.5
44.0
43.5
43.0
fRF = 375MHz
42.5
42.0
fRF = 433MHz
41.5
35
-5
5
50
10
MAX7033 toc09
UPPER
SIDEBAND
-10
45.0
IMAGE REJECTION (dB)
55
55
MAX7033 toc07
65
0
-3.5
1.0
-140 -120 -100
110
-2.5
1.2
1.0
-124
-40
-0.5
DELTA
-118
MAX7033 toc08
SENSITIVITY (dBm)
-112
6
VAC = VDVDD
MAX7033 toc06
2.4
41.0
40.5
30
280 300 320 340 360 380 400 420 440 460 480
RF FREQUENCY (MHz)
-40
-15
10
35
TEMPERATURE (°C)
_______________________________________________________________________________________
60
85
DELTA (%)
IF BANDWIDTH = 280kHz
MAX7033 toc05
AVERAGE CARRIER POWER
0.2% BER
IF BANDWIDTH = 280kHz
-110
2.4
MAX7033 toc04
-108
RSSI AND DELTA
vs. IF INPUT POWER
RSSI vs. RF INPUT POWER
SENSITIVITY vs. TEMPERATURE
SYSTEM GAIN (dB)
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
NORMALIZED IF GAIN
vs. IF FREQUENCY
S11 LOG MAGNITUDE PLOT OF RFIN
30
-15
-20
WITH INPUT
MATCHING
20
10
0
-10
200MHz
-20
315MHz
-36dB
-30
-25
-40
-30
-50
10
1
FREQUENCY (MHz)
REGULATOR VOLTAGE
vs. REGULATOR CURRENT
PHASE NOISE
vs. OFFSET FREQUENCY
0
MAX7033 toc13
2.9
-40°C
2.7
+25°C
2.5
2.3
+85°C
2.1
-20
PHASE NOISE (dBc/Hz)
3.1
fRF = 315MHz
+105°C
PHASE NOISE
vs. OFFSET FREQUENCY
-40
-60
-80
-100
1.7
10
20
30
40
REGULATOR CURRENT (mA)
50
60
-40
-60
-80
-100
-140
-140
0
fRF = 433MHz
-20
-120
-120
1.9
0
PHASE NOISE (dBc/Hz)
3.3
REGULATOR VOLTAGE (V)
0 100 200 300 400 500 600 700 800 900 1000
100
IF FREQUENCY (MHz)
3.5
500MHz
315MHz
MAX7033 toc15
-10
MAX7033 toc12
MAX7033 toc14
-5
S11 SMITH CHART PLOT OF RFIN
MAX7033 toc11
40
S11 MAGNITUDE (dB)
0
NORMALIZED IF GAIN (dB)
50
MAX7033 toc10
5
10
100
1k
10k
100k
OFFSET FREQUENCY (Hz)
1M
10M
10
100
1k
10k
100k
1M
10M
OFFSET FREQUENCY (Hz)
_______________________________________________________________________________________
7
MAX7033
Typical Operating Characteristics (continued)
(Typical Application Circuit , VAVDD = VDVDD = VDD5 = +3.3V, fRF = 315MHz, TA = +25°C, unless otherwise noted.)
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
MAX7033
Pin Description
PIN
TSSOP
THIN QFN
1
29
FUNCTION
XTAL1
Crystal Input 1 (See the Phase-Locked Loop section)
2, 7
4, 30
AVDD
Positive Analog Supply Voltage. For +5V operation, pin 2 is the output of an on-chip +3.2V
low-dropout regulator, and should be bypassed to AGND with a 0.1μF capacitor as close as
possible to the pin. Pin 7 must be externally connected to the supply from pin 2, and bypassed
to AGND with a 0.01μF capacitor as close as possible to the pin. (See the Voltage Regulator
section and the Typical Application Circuit.)
3
31
LNAIN
Low-Noise Amplifier Input (See the Low-Noise Amplifier section)
4
32
LNASRC
5, 10
2, 7
AGND
Low-Noise Amplifier Source for External Inductive Degeneration. Connect inductor to ground
to set the LNA input impedance (See the Low-Noise Amplifier section).
Analog Ground
Low-Noise Amplifier Output. Connect to mixer input through an LC tank filter (See the LowNoise Amplifier section).
6
3
LNAOUT
8
5
MIXIN1
1st Differential Mixer Input. Connect to LC tank filter from LNAOUT.
9
6
MIXIN2
2nd Differential Mixer Input. Connect through a 100pF capacitor to VDD3 side of the LC tank.
11
8
IRSEL
Image-Rejection Select. Set VIRSEL = 0V to center image rejection at 315MHz. Leave IRSEL
unconnected to center image rejection at 375MHz. Set VIRSEL = VDD5 to center image
rejection at 433MHz.
12
9
MIXOUT
13
10
DGND
Digital Ground
14
11
DVDD
Positive Digital Supply Voltage. Connect to both of the AVDD pins. Bypass to DGND with a
0.01μF capacitor as close as possible to the pin. (See the Typical Application Circuit.)
15
12
AC
16
14
XTALSEL
17
15
IFIN1
1st Differential Intermediate-Frequency Limiter Amplifier Input. Bypass to AGND with a 1500pF
capacitor as close to the pin as possible.
18
16
IFIN2
2nd Differential Intermediate-Frequency Limiter Amplifier Input. Connect to the output of a
10.7MHz bandpass filter.
19
17
DFO
Data Filter Output
20
18
DSN
Negative Data Slicer Input
21
19
OPP
Noninverting Op-Amp Input for the Sallen-Key Data Filter
22
20
DFFB
Data-Filter Feedback Node. Input for the feedback of the Sallen-Key data filter.
23
22
DSP
Positive Data Slicer Input
VDD5
+5V Supply Voltage. Bypass to AGND with a 0.01μF capacitor as close as possible to the pin.
For +5V operation, VDD5 is the input to an on-chip voltage regulator whose +3.2V output
appears at the pin 2 AVDD pin. (See the Voltage Regulator section and the Typical Application
Circuit.)
24
23
25
24
26
26
27
8
NAME
27
330Ω Mixer Output. Connect to the input of the 10.7MHz bandpass filter.
Automatic Gain Control. See Figure 1. Internally pulled down to AGND with a 100kΩ resistor.
Crystal Divider Ratio Select. Drive XTALSEL low to select fLO/fXTAL ratio of 64, or drive
XTALSEL high to select fLO/fXTAL ratio of 32.
DATAOUT Digital Baseband Data Output
PDOUT
SHDN
Peak-Detector Output
Power-Down Select Input. Drive high to power up the IC. Internally pulled down to AGND with
a 100kΩ resistor.
_______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
PIN
NAME
FUNCTION
TSSOP
THIN QFN
28
28
XTAL2
—
1, 13,
21, 25
N.C
No Connection
—
—
EP
Exposed Pad (TQFN Only). Connect EP to GND.
Crystal Input 2. Can also be driven with an external reference oscillator. (See the Crystal
Oscillator section.)
Functional Diagram
LNASRC
4
LNAIN
AVDD
VDD5
AVDD
DVDD
DGND
AGND
3
AC
15
LNAOUT
6
MIXIN1 MIXIN2
8
9
Q
IMAGE
REJECTION
2
24
IFIN1
17
28-PIN TSSOP
PACKAGE
IFIN2
18
0˚
AUTOMATIC
GAIN
CONTROL
LNA
MIXOUT
12
IRSEL
11
IF LIMITING
AMPS
∑
90˚
3.2V REG
I
MAX7033
RSSI
7
14
13
5, 10
DIVIDE
BY 64
VCO
PHASE
DETECTOR
LOOP
FILTER
÷1
DATA
FILTER
RDF1
100kΩ
RDF2
100kΩ
÷2
CRYSTAL
DRIVER
16
1
XTALSEL
XTAL1 XTAL2
28
DATA
SLICER
POWERDOWN
27
SHDN
25
DATAOUT
Detailed Description
The MAX7033 CMOS superheterodyne receiver and a
few external components provide the complete receive
chain from the antenna to the digital output data.
Depending on signal power and component selection,
data rates as high as 33kbps Manchester (66kbps
NRZ) can be achieved.
The MAX7033 is designed to receive binary ASK data
modulated in the 300MHz to 450MHz frequency range.
ASK modulation uses a difference in amplitude of the
carrier to represent logic 0 and logic 1 data.
Voltage Regulator
For operation with a single +3.0V to +3.6V supply voltage,
connect AVDD, DVDD, and VDD5 to the supply voltage.
20
23
19
DSN DSP DFO
26
21
22
PDOUT
OPP
DFFB
For operation with a single +4.5V to +5.5V supply voltage,
connect VDD5 to the supply voltage. An on-chip voltage
regulator drives one of the AVDD pins to approximately
+3.2V. For proper operation, DVDD and both the AVDD
pins must be connected together. Bypass VDD5, DVDD,
and the pin 7 AVDD pin to AGND with 0.01μF capacitors,
and the pin 2 AVDD pin to AGND with a 0.1μF capacitor,
all placed as close as possible to the pins.
Low-Noise Amplifier
The LNA is an nMOS cascode amplifier with off-chip
inductive degeneration, with a 3.0dB noise figure and
an IIP3 of -12dBm. The gain and noise figures are
dependent on both the antenna matching network at
the LNA input and the LC tank network between the
LNA output and the mixer inputs.
_______________________________________________________________________________________
9
MAX7033
Pin Description (continued)
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
The off-chip inductive degeneration is achieved by
connecting an inductor from LNASRC to AGND. This
inductor sets the real part of the input impedance at
LNAIN, allowing for a more flexible input impedance
match, such as a typical PCB trace antenna. A nominal
value for this inductor with a 50Ω input impedance is
15nH, but is affected by PCB trace.
The LC tank filter connected to LNAOUT comprises L3
and C2 (see the Typical Application Circuit). Select L3
and C2 to resonate at the desired RF input frequency.
The resonant frequency is given by:
fRF =
1
2π L TOTAL × CTOTAL
where:
LTOTAL = L3 + LPARASITICS.
CTOTAL = C2 + CPARASITICS.
LPARASITICS and CPARASITICS include inductance and
capacitance of the PCB traces, package pins, mixer
input impedance, LNA output impedance, etc. These
parasitics at high frequencies cannot be ignored, and
can have a dramatic effect on the tank filter center frequency. Lab experimentation should be done to optimize the center frequency of the tank.
Automatic Gain Control
When the AC pin is low, the automatic gain-control
(AGC) circuit monitors the RSSI output. As the RSSI
output reaches 1.98V, which corresponds to RF input
level of -62dBm, the AGC switches on the LNA gain
reduction resistor. The resistor reduces the LNA gain
by 35dB, thereby reducing the RSSI output by about
500mV. The LNA resumes high-gain mode when the
RSSI level drops back below 1.39V (approximately
-70dBm at RF input) for 1ms. The AGC has a hysteresis
of 8dB. With the AGC function, the MAX7033 can reliably produce an ASK output for RF input levels up to
0dBm with modulation depth of 18dB.
When the AC pin is high and SHDN goes high, the
AGC circuit is disabled and the LNA is always in highgain mode. The AGC function can be resumed by
bringing the AC pin low when SHDN is high.
The MAX7033 features an AGC lock function that is
asserted when the level at the AC pin transitions from
low to high while SHDN is high. Locking the AGC locks
the LNA in the current gain state. As shown in Figure 1,
the AGC lock function can be enabled or disabled as
long as the SHDN pin is high. Changing the state of AC
when SHDN is low has no effect.
Mixer
A unique feature of the MAX7033 is the integrated
image rejection of the mixer. This device eliminates the
need for a costly front-end SAW filter for most applications. Advantages of not using a SAW filter are
increased sensitivity, simplified antenna matching, less
board space, and lower cost.
The mixer cell is a pair of double balanced mixers that
perform an IQ downconversion of the RF input to the
10.7MHz IF from a low-side injected LO (i.e., fLO = fRF fIF). The image-rejection circuit then combines these
signals to achieve 44dB of image rejection. Low-side
VIH
SHDN
PIN
VIL
VIH
AC PIN
VIL
AGC
LOCK
AGC
UNLOCK
AGC
LOCK
AGC ENABLED
AGC
UNLOCK
NO
EFFECT
NO
EFFECT
AGC
DISABLED
NO
EFFECT
AGC
ENABLED
Figure 1. AGC Lock Activation Cycles
10
______________________________________________________________________________________
AGC
DISABLED
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Phase-Locked Loop
The PLL block contains a phase detector, charge
pump, integrated loop filter, VCO, asynchronous 64x
clock divider, and crystal oscillator driver. Besides the
crystal, this PLL does not require any external components. The VCO generates a low-side LO. The relationship between the RF, IF, and crystal frequencies is
given by:
f -f
fXTAL = RF IF
32 × M
where:
M = 1 (VXTALSEL = VDD5) or 2 (VXTALSEL = 0V)
To allow the smallest possible IF bandwidth (for best sensitivity), minimize the tolerance of the reference crystal.
Table 1. Component Values for Typical Application Circuit
COMPONENT
VALUE FOR fRF = 433MHz
VALUE FOR fRF = 315MHz
DESCRIPTION
C1
100pF
100pF
5%
C2
2pF
4pF
± 0.1pF
C3
100pF
100pF
5%
C4
100pF
100pF
5%
C5
1500pF
1500pF
10%
C6
220pF
220pF
5%
C7
470pF
470pF
5%
C8
0.47μF
0.47μF
20%
C9
220pF
220pF
10%
C10
0.01μF
0.01μF
20%
C11
0.1μF
0.1μF
20%
C12
15pF
15pF
Depends on XTAL
C13
15pF
15pF
Depends on XTAL
C14
0.01μF
0.01μF
20%
C15
0.01μF
0.01μF
20%
L1
56nH
120nH
5% or better*
L2
15nH
15nH
5% or better*
L3
15nH
27nH
5% or better*
R1
5.1kΩ
5.1kΩ
5%
R2
Open
Open
—
R3
Short
Short
—
X1 (÷64)
6.6128MHz**
4.7547MHz**
Crystek or Hong Kong Crystal
X1 (÷32)
13.2256MHz**
9.5094MHz**
Crystek or Hong Kong Crystal
Y1
10.7MHz ceramic filter
10.7MHz ceramic filter
Murata
*Wire wound recommended.
**Crystal frequencies shown are for ÷64 (VXTALSEL = 0V) and ÷32 (VXTALSEL = VDD)
______________________________________________________________________________________
11
MAX7033
injection is required due to the on-chip image-rejection
architecture. The IF output is driven by a source follower biased to create a driving-point impedance of 330Ω;
this provides a good match to the off-chip 330Ω ceramic IF filter.
The IRSEL pin is a logic input that selects one of the
three possible image-rejection frequencies. When VIRSEL
= 0V, the image rejection is tuned to 315MHz. VIRSEL =
VDD5/2 tunes the image rejection to 375MHz, and VIRSEL
= VDD5 tunes the image rejection to 433MHz. The IRSEL
pin is internally set to V DD5 /2 (image rejection at
375MHz) when it is left unconnected, thereby eliminating
the need for an external VDD5/2 voltage.
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Intermediate Frequency and RSSI
The IF section presents a differential 330Ω load to provide matching for the off-chip ceramic filter. The six
internal AC-coupled limiting amplifiers produce an
overall gain of approximately 65dB, with a bandpass-filter-type response centered near the 10.7MHz IF frequency with a 3dB bandwidth of approximately 10MHz.
The RSSI circuit demodulates the IF by producing a DC
output proportional to the log of the IF signal level, with
a slope of approximately 14.2mV/dB (see the Typical
Operating Characteristics).
Applications Information
Crystal Oscillator
The crystal oscillator in the MAX7033 is designed to
present a capacitance of approximately 3pF between
the XTAL1 and XTAL2. If a crystal designed to oscillate
with a different load capacitance is used, the crystal is
pulled away from its stated operating frequency, introducing an error in the reference frequency. Crystals
designed to operate with higher differential load capacitance always pull the reference frequency higher. For
example, a 4.7547MHz crystal designed to operate
with a 10pF load capacitance oscillates at 4.7563MHz
with the MAX7033, causing the receiver to be tuned to
315.1MHz rather than 315.0MHz, an error of about
100kHz, or 320ppm.
In actuality, the oscillator pulls every crystal. The crystal’s natural frequency is really below its specified frequency, but when loaded with the specified load
capacitance, the crystal is pulled and oscillates at its
specified frequency. This pulling is already accounted
for in the specification of the load capacitance.
Additional pulling can be calculated if the electrical
parameters of the crystal are known. The frequency
pulling is given by:
⎞
C ⎛
1
1
fP = M ⎜
× 106
2 ⎝ CCASE + CLOAD CCASE + CSPEC ⎟⎠
It is possible to use an external reference oscillator in
place of a crystal to drive the VCO. AC-couple the external oscillator to XTAL2 with a 1000pF capacitor. Drive
XTAL2 with a signal level of approximately -10dBm. ACcouple XTAL1 to ground with a 1000pF capacitor.
Data Filter
The data filter is implemented as a 2nd-order lowpass
Sallen-Key filter. The pole locations are set by the combination of two on-chip resistors and two external
capacitors. Adjusting the value of the external capacitors changes the corner frequency to optimize for different data rates. The corner frequency should be set
to approximately 1.5 times the fastest expected data
rate from the transmitter. Keeping the corner frequency
near the data rate rejects any noise at higher frequencies, resulting in an increase in receiver sensitivity.
The configuration shown in Figure 2 can create a
Butterworth or Bessel response. The Butterworth filter
offers a very flat amplitude response in the passband
and a rolloff rate of 40dB/decade for the two-pole filter.
The Bessel filter has a linear phase response, which
works well for filtering digital data. To calculate the
value of C5 and C6, use the following equations, along
with the coefficients in Table 2:
C5 =
b
a(100k)( π)(fC )
C6 =
a
4(100k)( π)(fC )
where fC is the desired 3dB corner frequency.
Table 2. Coefficents to Calculate C5 and C6
a
b
Butterworth (Q = 0.707)
FILTER TYPE
1.414
1.000
Bessel (Q = 0.577)
1.3617
0.618
where:
fP is the amount the crystal frequency pulled in ppm.
CM is the motional capacitance of the crystal.
CCASE is the case capacitance.
CSPEC is the specified load capacitance.
CLOAD is the actual load capacitance.
When the crystal is loaded as specified, i.e., CLOAD =
CSPEC, the frequency pulling equals zero.
RSSI
MAX7033
RDF1
100kΩ
RDF2
100kΩ
22
DFFB
21
OPP
19
DFO
C6
C5
Figure 2. Sallen-Key Lowpass Data Filter
12
______________________________________________________________________________________
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
MAX7033
For example, to choose a Butterworth filter response
with a corner frequency of 5kHz:
1.000
MAX7033
≈ 450pF
C5 =
(1.414)(100kΩ)(3.14)(5kHz)
C6 =
1.414
≈ 225pF
k
Ω
4
100
( )(
)(3.14)(5kHz)
DATA
SLICER
Choosing standard capacitor values changes C5 to
470pF and C6 to 220pF, as shown in the Typical
Application Circuit.
Data Slicer
The data slicer takes the analog output of the data filter
and converts it to a digital signal. This is achieved by
using a comparator and comparing the analog input to
a threshold voltage. One input is supplied by the data
filter output. Both comparator inputs are accessible offchip to allow for different methods of generating the
slicing threshold, which is applied to the second comparator input.
The suggested data slicer configuration uses a resistor
(R1) connected between DSN and DSP with a capacitor (C4) from DSN to DGND (Figure 3). This configuration averages the analog output of the filter and sets the
threshold to approximately 50% of that amplitude. With
this configuration, the threshold automatically adjusts
as the analog signal varies, minimizing the possibility
for errors in the digital data. The values of R1 and C4
affect how fast the threshold tracks to the analog amplitude. Be sure to keep the corner frequency of the RC
circuit much lower than the lowest expected data rate.
Note that a long string of zeros or ones can cause the
threshold to drift. This configuration works best if a coding scheme, such as Manchester coding, which has an
equal number of zeros and ones, is used.
To prevent continuous toggling of DATAOUT in the
absence of an RF signal due to noise, add hysteresis to
the data slicer as shown in Figure 4.
19
DFO
23
DSP
R1
C4
Figure 3. Generating Data Slicer Threshold
MAX7033
DATA
SLICER
25
DATAOUT
20
DSN
23
DSP
R4
19
DFO
R1
R3
R2
C4
*OPTIONAL
Figure 4. Generating Data Slicer Hysteresis
MAX7033
Peak Detector
The peak-detector output (PDOUT), in conjunction with
an external RC filter, creates a DC output voltage equal
to the peak value of the data signal. The resistor provides a path for the capacitor to discharge, allowing the
peak detector to dynamically follow peak changes of
the data-filter output voltage. For faster data slicer
response, use the circuit shown in Figure 5.
20
DSN
25
DATAOUT
DATA
SLICER
25
DATAOUT
20
DSN
23
DSP
19
DFO
26
PDOUT
25kΩ
47nF
Figure 5. Using PDOUT for Faster Startup
______________________________________________________________________________________
13
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Layout Considerations
A properly designed PCB is an essential part of any
RF/microwave circuit. On high-frequency inputs and
outputs, use controlled-impedance lines and keep
them as short as possible to minimize losses and radiation. At high frequencies, trace lengths that are on the
order of λ/10 or longer act as antennas.
Keeping the traces short also reduces parasitic inductance. Generally, 1in of a PCB trace adds about 20nH
of parasitic inductance. The parasitic inductance can
have a dramatic effect on the effective inductance of a
passive component. For example, a 0.5in trace connecting a 100nH inductor adds an extra 10nH of inductance or 10%.
To reduce the parasitic inductance, use wider traces
and a solid ground or power plane below the signal
traces. Also, use low-inductance connections to
ground on all GND pins, and place decoupling capacitors close to all power-supply pins.
Control Interface Considerations
When operating the MAX7033 with a +4.5V to +5.5V
supply voltage, the SHDN and AC pins can be driven
by a microcontroller with either 3V or 5V interface logic
levels. When operating the MAX7033 with a +3.0V to
+3.6V supply, only 3V logic from the microcontroller is
allowed.
Typical Application Circuit
VDD3
IF VDD IS
VDD
(SEE TABLE)
THEN VDD3 IS
3.0V TO 3.6V CONNECTED TO VDD
CREATED BY LDO,
4.5V TO 5.5V AVAILABLE AT AVDD
(PIN 2)
X1
C11
C13
1
RF INPUT
2
C1
L1
3
4
L2
5
6
C14
VDD3
7
L3
C3
8
C2
9
C4
10
C9
11
12
13
14
**
XTAL1
XTAL2
AVDD
SHDN
LNAIN
PDOUT
LNASRC
MAX7033
DATAOUT
AGND
VDD5
LNAOUT
DSP
AVDD
DFFB
MIXIN1
OPP
MIXIN2
DSN
AGND
DFO
IRSEL
IFIN2
MIXOUT
IFIN1
DGND
XTALSEL
DVDD
AC
28
C12
TO/FROM μP
POWER-DOWN
DATA OUT
27
26
R2
25
C15
24
R3
23
22
21
C7
20
19
18
17
R1
16
15
C5
Y1
C10
COMPONENT VALUES
IN TABLE 1
**SEE THE MIXER SECTION.
14
C6
*
IF FILTER
IN
OUT
GND
*SEE PHASE-LOCKED LOOP SECTION.
______________________________________________________________________________________
C8
FROM μP
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
PROCESS: CMOS
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maxim-ic.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
LAND
PACKAGE
PACKAGE
OUTLINE NO.
PATTERN NO.
TYPE
CODE
28 TSSOP
U28+1
21-0066
90-0171
32 TQFN-EP
T3255+3
21-0140
90-0001
______________________________________________________________________________________
15
MAX7033
Chip Information
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Revision History
REVISION
NUMBER
REVISION
DATE
0
7/04
Initial release
1/11
Updated Ordering Information, Pin Configurations, Absolute Maximum Ratings,
DC Electrical Characteristics, AC Electrical Characteristics, Typical Operating
Characteristics, Pin Description, Functional Diagram, Voltage Regulator and
Layout Considerations sections, Typical Application Circuit, Chip Information,
and Package Information
9/11
Updated input impedance values in AC Electrical Characteristics table; updated
TOC3 and TOC4 labels in Typical Operating Characteristics; clarified equations
in Pin Description and Phase-Locked Loop and Crystal Oscillator sections;
updated components in Table 1; and added new Control Interface
Considerations section
1
2
DESCRIPTION
PAGES
CHANGED
—
1–9, 13, 14, 15
3–6, 11–14
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in
the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2011 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.