19-3109; Rev 0; 1/08 315MHz/434MHz ASK Superheterodyne Receiver The MAX7034 fully integrated low-power CMOS superheterodyne receiver is ideal for receiving amplitudeshift-keyed (ASK) data in the 300MHz to 450MHz frequency range (including the popular 315MHz and 433.92MHz frequencies). The receiver has an RF sensitivity of -114dBm. With few external components and a low-current power-down mode, it is ideal for cost-sensitive and power-sensitive applications typical in the automotive and consumer markets. The MAX7034 consists of a low-noise amplifier (LNA), a fully differential image-rejection mixer, an on-chip phase-locked loop (PLL) with integrated voltage-controlled oscillator (VCO), a 10.7MHz IF limiting amplifier stage with received-signal-strength indicator (RSSI), and analog baseband data-recovery circuitry. Features ♦ Optimized for 315MHz or 433.92MHz Band ♦ Operates from Single +5.0V Supply ♦ Selectable Image-Rejection Center Frequency ♦ Selectable x64 or x32 fLO/fXTAL Ratio ♦ Low (< 6.7mA) Operating Supply Current ♦ < 3.0µA Low-Current Power-Down Mode for Efficient Power Cycling ♦ 250µs Startup Time ♦ Built-In 44dB RF Image Rejection ♦ Excellent Receive Sensitivity Over Temperature ♦ -40°C to +125°C Operation The MAX7034 is available in a 28-pin TSSOP package and is specified over the automotive (-40°C to +125°C) temperature range. Applications Automotive Remote Keyless Entry Security Systems Garage Door Openers Ordering Information PART TEMP RANGE PINPACKAGE PKG CODE -40°C to +125°C 28 TSSOP (9.7mm x 4.4mm) U28-1 Home Automation Remote Controls Local Telemetry Wireless Sensors MAX7034AUI+T +Denotes a lead-free package. T = Tape-and-reel. Typical Application Circuit appears at end of data sheet. Pin Configuration TOP VIEW XTAL1 1 + 28 XTAL2 AVDD 2 27 SHDN LNAIN 3 26 PDOUT 25 DATAOUT LNASRC 4 AGND 5 LNAOUT 6 MAX7034 24 VDD5 23 DSP 22 DFFB AVDD 7 MIXIN1 8 21 OPP MIXIN2 9 20 DSN AGND 10 19 DFO IRSEL 11 18 IFIN2 MIXOUT 12 17 IFIN1 DGND 13 16 XTALSEL DVDD 14 15 EN_REG TSSOP ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX7034 General Description MAX7034 315MHz/434MHz ASK Superheterodyne Receiver ABSOLUTE MAXIMUM RATINGS VDD5 to AGND.......................................................-0.3V to +6.0V AVDD to AGND ......................................................-0.3V to +4.0V DVDD to DGND......................................................-0.3V to +4.0V AGND to DGND.....................................................-0.1V to +0.1V IRSEL, DATAOUT, XTALSEL, SHDN, EN_REG to AGND ....................-0.3V to (VDD5 + 0.3V) All Other Pins to AGND............................-0.3V to (DVDD + 0.3V) Continuous Power Dissipation (TA = +70°C) 28-Pin TSSOP (derate 12.8mW/°C above +70°C) ..1025.6mW Operating Temperature Range .........................-40°C to +125°C Storage Temperature Range .............................-65°C to +150°C Junction Temperature ......................................................+150°C Lead Temperature (soldering, 10s) .................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS (Typical Application Circuit, VDD5 = +4.5V to +5.5V, no RF signal applied. TA = -40°C to +125°C, unless otherwise noted. Typical values are at VDD5 = +5.0V and TA = +25°C, unless otherwise noted.) (Note 1) PARAMETER SYMBOL Supply Voltage VDD5 Supply Current IDD Shutdown Supply Current Input-Voltage Low Input-Voltage High Input Logic Current High ISHDN CONDITIONS MIN TYP MAX UNITS +5.0V nominal supply voltage 4.5 5.0 5.5 V fRF = 315MHz 6.7 8.2 fRF = 434MHz 7.2 8.7 3 8 µA 0.4 V VSHDN = VDD5 VSHDN = 0V VIL EN_REG, SHDN VDD5 0.4 XTALSEL DVDD 0.4 VIH IIH Image-Reject Select Voltage (Note 2) V 15 fRF = 434MHz, VIRSEL = DVDD fRF = 375MHz, VIRSEL = DVDD/2 mA µA DVDD 0.4 DVDD 1.5 1.1 fRF = 315MHz, VIRSEL = 0V V 0.4 DATAOUT Output-Voltage Low VOL ISINK = 10µA 0.125 V DATAOUT Output-Voltage High VOH ISOURCE = 10µA VDD5 0.125 V 2 _______________________________________________________________________________________ 315MHz/434MHz ASK Superheterodyne Receiver (Typical Application Circuit, VVDD5 = +4.5V to +5.5V, all RF inputs are referenced to 50Ω, fRF = 433.92MHz, TA = -40°C to +125°C, unless otherwise noted. Typical values are at VVDD5 = +5.0V and TA = +25°C.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS GENERAL CHARACTERISTICS Startup Time tON Receiver Input Frequency Range fRF Time for valid signal detection after VSHDN = VDD5. Does not include baseband filter settling. 250 300 Maximum Receiver Input Level 450 0 Sensitivity at TA = +25oC (Note 3) Sensitivity at TA = +125°C (Note 3) Maximum Data Rate µs +25°C, 315MHz -114 +25°C, 434MHz -113 +125°C, 315MHz -113 +125°C, 434MHz -110 MHz dBm dBm dBm Manchester coded 33 NRZ coded 66 330Ω IF filter load 45 dB -50 dBm 330 Ω kbps LNA/MIXER LNA/Mixer Voltage Gain (Note 4) LNA/Mixer Input-Referred 1dB Compression Point Mixer Output Impedance ZOUT_MIX Mixer Image Rejection fRF = 434MHz, VIRSEL = DVDD 42 fRF = 375MHz, VIRSEL = DVDD/2 44 fRF = 315MHz, VIRSEL = 0V 44 dB INTERMEDIATE FREQUENCY (IF) Input Impedance ZIN_IF Operating Frequency fIF Bandpass response 3dB Bandwidth RSSI Linearity RSSI Dynamic Range RSSI Level 330 Ω 10.7 MHz 10 MHz ±0.5 dB 80 dB PRFIN < -120dBm 1.15 PRFIN > -40dBm 2.2 V _______________________________________________________________________________________ 3 MAX7034 AC ELECTRICAL CHARACTERISTICS MAX7034 315MHz/434MHz ASK Superheterodyne Receiver AC ELECTRICAL CHARACTERISTICS (continued) (Typical Application Circuit, VVDD5 = +4.5V to +5.5V, all RF inputs are referenced to 50Ω, fRF = 433.92MHz, TA = -40°C to +125°C, unless otherwise noted. Typical values are at VVDD5 = +5.0V and TA = +25°C.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DATA FILTER Maximum Bandwidth 50 kHz 100 kHz DATA SLICER Comparator Bandwidth Maximum Load Capacitance 10 pF Output High Voltage CLOAD VVDD5 V Output Low Voltage 0 V CRYSTAL OSCILLATOR fRF = 433.92MHz Crystal Frequency (Note 5) fXTAL fRF = 315MHz VXTALSEL = 0V 6.6128 VXTALSEL = DVDD 13.2256 VXTALSEL = 0V 4.7547 VXTALSEL = DVDD 9.5094 Crystal Tolerance Input Capacitance From each pin to ground MHz 50 ppm 6.2 pF Note 1: 100% tested at TA = +125°C. Guaranteed by design and characterization over entire temperature range. Note 2: IRSEL is internally set to 375MHz IR mode. It can be left open when the 375MHz image-rejection setting is desired. Bypass to AGND with a 1nF capacitor in a noisy environment. Note 3: Peak power level. BER = 2 x 10-3, Manchester encoded, data rate = 4kbps, IF bandwidth = 280kHz. Note 4: The voltage conversion gain is measured with the LNA input matching inductor and the LNA/Mixer resonator in place, and does not include the IF filter insertion loss. Note 5: Crystal oscillator frequency for other RF carrier frequency within the 300MHz to 450MHz range is (fRF - 10.7MHz)/64 for XTALSEL = 0V, and (fRF - 10.7MHz)/32 for XTALSEL = DVDD. 4 _______________________________________________________________________________________ 315MHz/434MHz ASK Superheterodyne Receiver MAX7034 Typical Operating Characteristics (Typical Application Circuit, VDD5 = +5.0V, fRF = 433.92MHz, TA = +25°C, unless otherwise noted.) +85°C 7.2 7.0 +25°C +105°C +125°C -40°C 6.8 8.0 MAX7034 toc02 +125°C 433.92MHz 10.00 7.5 7.0 6.5 +25°C 6.0 5.5 6.6 4.9 5.1 5.3 SUPPLY VOLTAGE (V) 5.5 0.01 250 SENSITIVITY vs. TEMPERATURE -104 -106 350 400 450 RF FREQUENCY (MHz) -130 500 2.20 -125 -120 -115 PEAK RF INPUT POWER (dBm) -110 RSSI AND DELTA vs. IF INPUT POWER RSSI vs. RF INPUT POWER 433.92MHz -108 300 2.40 MAX7034 toc04 -102 315MHz -40°C IF BANDWIDTH = 280kHz MAX7034 toc06 2.40 MAX7034 toc05 4.7 1.00 0.10 5.0 4.5 2.20 2.00 2.00 1.80 1.80 15 RSSI 10 5 1.60 -5 DELTA 1.60 -10 -114 1.40 1.40 1.20 1.20 -15 -116 -120 110 -140 -120 -100 -80 -60 -40 RF INPUT POWER (dBm) UPPER SIDEBAND 45 49.7dB IMAGE REJECTION 35 fRF = 315MHz 50 IMAGE REJECTION (dB) 55 25 15 LOWER SIDEBAND 30 fRF = 433.92MHz 10 5 0 5 10 15 20 IF FREQUENCY (MHz) 25 30 52 50 48 315MHz 46 433.92MHz 44 42 0 -5 10 IMAGE REJECTION vs. TEMPERATURE 40 20 -25 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 IF INPUT POWER (dBm) 0 IMAGE REJECTION vs. RF FREQUENCY 60 MAX7034 toc07 65 -20 IMAGE REJECTION (dB) 10 35 60 85 TEMPERATURE (°C) MAX7034 toc08 -15 LNA/MIXER VOLTAGE GAIN vs. IF FREQUENCY LNA/MIXER VOLTAGE GAIN (dB) 1.00 1.00 -40 -20 MAX7034 toc09 -118 40 280 300 320 340 360 380 400 420 440 460 480 RF FREQUENCY (MHz) -40 -15 10 35 60 85 TEMPERATURE (°C) 110 _______________________________________________________________________________________ 5 DELTA -112 RSSI (V) 0 315MHz -110 RSSI (V) SENSITIVITY (dBm) +85°C 100.00 BIT-ERROR RATE (%) 7.4 +105°C 8.5 SUPPLY CURRENT (mA) 7.6 SUPPLY CURRENT (mA) 9.0 MAX7034 toc01 7.8 BIT-ERROR RATE vs. PEAK RF INPUT POWER SUPPLY CURRENT vs. RF FREQUENCY MAX7034 toc03 SUPPLY CURRENT vs. SUPPLY VOLTAGE Typical Operating Characteristics (continued) (Typical Application Circuit, VDD5 = +5.0V, fRF = 433.92MHz, TA = +25°C, unless otherwise noted.) NORMALIZED IF GAIN vs. IF FREQUENCY S11 MAGNITUDE PLOT OF RFIN vs. FREQUENCY 40 30 S11 MAGNITUDE (dB) -5 -10 -15 -20 MAX7034 toc12 MAX7034 toc11 0 S11 SMITH CHART PLOT OF RFIN 50 MAX7034 toc10 5 NORMALIZED IF GAIN (dB) 500MHz WITH INPUT MATCHING 20 10 0 315MHz -10 200MHz 315MHz -24.1dB -20 -30 -25 -40 -30 -50 100 10 200 230 260 290 320 350 380 410 440 470 500 IF FREQUENCY (MHz) FREQUENCY (MHz) PHASE NOISE vs. OFFSET FREQUENCY fRF = 315MHz -40 -60 -80 -100 -120 -40 -60 -80 -100 -120 -140 -140 10 100 1k 10k 100k OFFSET FREQUENCY (Hz) 6 fRF = 433.92MHz -20 PHASE NOISE (dBc/Hz) -20 0 MAX7033 toc13 0 PHASE NOISE vs. OFFSET FREQUENCY MAX7033 toc14 1 PHASE NOISE (dBc/Hz) MAX7034 315MHz/434MHz ASK Superheterodyne Receiver 1M 10M 10 100 1k 10k 100k 1M 10M OFFSET FREQUENCY (Hz) _______________________________________________________________________________________ 315MHz/434MHz ASK Superheterodyne Receiver PIN NAME FUNCTION 1 XTAL1 Crystal Input 1 2, 7 AVDD Positive Analog Supply Voltage. AVDD is connected to an on-chip +3.4V low-dropout regulator. Both AVDD pins must be externally connected to each other. Bypass pin 2 to AGND with a 0.1µF capacitor as close as possible to the pin (see the Typical Application Circuit). Bypass pin 7 with a 0.01µF capacitor. 3 LNAIN Low-Noise Amplifier Input. See the Low-Noise Amplifier section. 4 LNASRC 5, 10 AGND 6 LNAOUT 8 MIXIN1 1st Differential Mixer Input. Connect to LC tank filter from LNAOUT through a 100pF capacitor. See the Typical Application Circuit. 9 MIXIN2 2nd Differential Mixer Input. Connect to AVDD side of the LC tank filter through a 100pF capacitor. See the Typical Application Circuit. 11 IRSEL Image-Rejection Select. Set VIRSEL = 0V to center image rejection at 315MHz. Leave IRSEL unconnected to center image rejection at 375MHz. Set VIRSEL = DVDD to center image rejection at 434MHz. See the Mixer section. 12 MIXOUT 13 DGND Digital Ground 14 DVDD Positive Digital Supply Voltage. Connect to AVDD. Bypass to DGND with a 0.01µF capacitor as close as possible to the pin. 15 EN_REG Regulator Enable. Connect to VDD5 to enable internal regulator. Pull this pin low to allow device operation between +3.0V and +3.6V. See the Voltage Regulator section. 16 XTALSEL Crystal Divider Ratio Select. Drive XTALSEL low to select divider ratio of 64, or drive XTALSEL high to select divider ratio of 32. 17 IFIN1 1st Differential Intermediate-Frequency Limiter Amplifier Input. Connect to the output of a 10.7MHz bandpass filter. 18 IFIN2 2nd Differential Intermediate-Frequency Limiter Amplifier Input. Bypass to AGND with a 1500pF capacitor as close as possible to the pin. 19 DFO Data Filter Output 20 DSN Negative Data Slicer Input 21 OPP Noninverting Op-Amp Input for the Sallen-Key Data Filter 22 DFFB Data Filter Feedback Node. Input for the feedback of the Sallen-Key data filter. 23 DSP Positive Data Slicer Input 24 VDD5 +5.0V Supply Voltage 25 DATAOUT 26 PDOUT 27 SHDN Power-Down Select Input. Drive high to power up the IC. Internally pulled down to AGND with a 100kΩ resistor. 28 XTAL2 Crystal Input 2. Can also be driven with an external reference oscillator. See the Crystal Oscillator section. Low-Noise Amplifier Source for external Inductive Degeneration. Connect inductor to ground to set LNA input impedance. See the Low-Noise Amplifier section. Analog Ground Low-Noise Amplifier Output. Connect to mixer input through an LC tank filter. See the Low-Noise Amplifier section. 330Ω Mixer Output. Connect to the input of the 10.7MHz bandpass filter. Digital Baseband Data Output Peak-Detector Output _______________________________________________________________________________________ 7 MAX7034 Pin Description 315MHz/434MHz ASK Superheterodyne Receiver MAX7034 Functional Diagram LNASRC 4 LNAIN AVDD VDD5 DVDD DGND AGND 3 EN_REG LNAOUT 15 6 MIXIN1 MIXIN2 8 9 Q 3.4V REG IMAGE REJECTION 14 DIVIDE BY 64 VCO PHASE DETECTOR LOOP FILTER ÷1 IF LIMITING AMPS ∑ I MAX7034 RSSI DATA FILTER RDF1 100kΩ RDF2 100kΩ ÷2 CRYSTAL DRIVER 16 1 XTALSEL XTAL1 XTAL2 28 DATA SLICER POWERDOWN 27 SHDN 25 DATAOUT Detailed Description The MAX7034 CMOS superheterodyne receiver and a few external components provide the complete receive chain from the antenna to the digital output data. Depending on signal power and component selection, data rates can be as high as 33kbps Manchester (66kbps NRZ). The MAX7034 is designed to receive binary ASK data modulated in the 300MHz to 450MHz frequency range. ASK modulation uses a difference in amplitude of the carrier to represent logic 0 and logic 1 data. Voltage Regulator The MAX7034 is designed to work with a nominal +5.0V supply voltage. The MAX7034 integrates an internal voltage regulator that provides +3.4V to some of the internal circuits in the device; this voltage is connected to the AVDD and DVDD pins. The device can be operated from +3.0V to +3.6V by pulling the EN_REG pin low (which disables the internal voltage regulator) and connecting the supply voltage to the AVDD and DVDD pins. If the MAX7034 is powered from +3.0 to +3.6V, the performance is limited to the -40°C to +105°C range. Low-Noise Amplifier The LNA is an nMOS cascode amplifier with off-chip inductive degeneration. The gain and noise figures are 8 IFIN2 18 90˚ 24 5, 10 IFIN1 17 0˚ LNA 2, 7 13 MIXOUT 12 IRSEL 11 20 23 19 DSN DSP DFO 26 21 22 PDOUT OPP DFFB dependent on both the antenna matching network at the LNA input and the LC tank network between the LNA output and the mixer inputs. The off-chip inductive degeneration is achieved by connecting an inductor from LNASRC to AGND. This inductor sets the real part of the input impedance at LNAIN, allowing for a more flexible input impedance match, such as a typical printed-circuit board (PCB) trace antenna. A nominal value for this inductor with a 50Ω input impedance is 15nH, but is affected by the PCB trace. The LC tank filter connected to LNAOUT comprises L1 and C9 (see the Typical Application Circuit). Select L1 and C9 to resonate at the desired RF input frequency. The resonant frequency is given by: fRF = 1 2π L TOTAL × CTOTAL where: LTOTAL = L1 + LPARASITICS. CTOTAL = C9 + CPARASITICS. LPARASITICS and CPARASITICS include inductance and capacitance of the PCB traces, package pins, mixer input impedance, etc. These parasitics at high frequencies cannot be ignored, and can have a dramatic effect _______________________________________________________________________________________ 315MHz/434MHz ASK Superheterodyne Receiver Mixer A unique feature of the MAX7034 is the integrated image rejection of the mixer. This device eliminates the need for a costly front-end SAW filter for most applications. Advantages of not using a SAW filter are increased sensitivity, simplified antenna matching, less board space, and lower cost. The mixer cell is a pair of double balanced mixers that perform an IQ downconversion of the RF input to the 10.7MHz IF from a low-side injected LO (i.e., fLO = fRF fIF). The image-rejection circuit then combines these signals to achieve 44dB of image rejection. Low-side injection is required due to the on-chip image-rejection architecture. The IF output is driven by a source follower biased to create a driving-point impedance of 330Ω; this provides a good match to the off-chip 330Ω ceramic IF filter. The IRSEL pin is a logic input that selects one of the three possible image-rejection frequencies. When VIRSEL = 0V, the image rejection is tuned to 315MHz. VIRSEL = DV DD /2 tunes the image rejection to 375MHz, and VIRSEL = DVDD tunes the image rejection to 434MHz. The IRSEL pin is internally set to DVDD/2 (image rejection at 375MHz) when it is left unconnected, thereby eliminating the need for an external DVDD/2 voltage. Phase-Locked Loop The PLL block contains a phase detector, charge pump, integrated loop filter, VCO, asynchronous 64x clock divider, and crystal oscillator driver. Besides the crystal, this PLL does not require any external components. The VCO generates a low-side LO. The relationship between the RF, IF, and reference frequencies is given by: f - f fREF = RF IF 32 × M where: M = 1 (VXTALSEL = DVDD) or 2 (VXTALSEL = 0V) To allow the smallest possible IF bandwidth (for best sensitivity), minimize the tolerance of the reference crystal. Intermediate Frequency and RSSI The IF section presents a differential 330Ω load to provide matching for the off-chip ceramic filter. The six internal AC-coupled limiting amplifiers produce an overall gain of approximately 65dB, with a bandpassfilter-type response centered near the 10.7MHz IF frequency with a 3dB bandwidth of approximately 10MHz. The RSSI circuit demodulates the IF by producing a DC output proportional to the log of the IF signal level, with a slope of approximately 14.2mV/dB. Applications Information Crystal Oscillator The crystal oscillator in the MAX7034 is designed to present a capacitance of approximately 3pF between the XTAL1 and XTAL2. If a crystal designed to oscillate with a different load capacitance is used, the crystal is pulled away from its intended operating frequency, introducing an error in the reference frequency. Crystals designed to operate with higher differential load capacitance always pull the reference frequency higher. For example, a 4.7547MHz crystal designed to operate with a 10pF load capacitance oscillates at 4.7563MHz with the MAX7034, causing the receiver to be tuned to 315.1MHz rather than 315.0MHz, an error of about 100kHz, or 320ppm. It is very important to use a crystal with a load capacitance that is equal to the capacitance of the MAX7034 crystal oscillator plus PCB parasitics. In actuality, the oscillator pulls every crystal. The crystal’s natural frequency is really below its specified frequency, but when loaded with the specified load capacitance, the crystal is pulled and oscillates at its specified frequency. This pulling is already accounted for in the specification of the load capacitance. Additional pulling can be calculated if the electrical parameters of the crystal are known. The frequency pulling is given by: fP = ⎞ CM ⎛ 1 1 × 106 ⎜ 2 ⎝ CCASE + CLOAD CCASE + CSPEC ⎟⎠ where: fP is the amount the crystal frequency pulled in ppm. CM is the motional capacitance of the crystal. CCASE is the case capacitance. CSPEC is the specified load capacitance. CLOAD is the actual load capacitance. When the crystal is loaded as specified (i.e., CLOAD = CSPEC), the frequency pulling equals zero. It is possible to use an external reference oscillator in place of a crystal to drive the VCO. AC-couple the external oscillator to XTAL2 with a 1000pF capacitor. Drive XTAL2 with a signal level of approximately 500mVP-P. AC-couple XTAL1 to ground with a 1000pF capacitor. _______________________________________________________________________________________ 9 MAX7034 on the tank filter center frequency. The total parasitic capacitance is generally between 4pF and 6pF. MAX7034 315MHz/434MHz ASK Superheterodyne Receiver Data Filter The data filter is implemented as a 2nd-order lowpass Sallen-Key filter. The pole locations are set by the combination of two on-chip resistors and two external capacitors. Adjusting the value of the external capacitors changes the corner frequency to optimize for different data rates. The corner frequency should be set to approximately 1.5 times the fastest expected data rate from the transmitter. Keeping the corner frequency near the data rate rejects any noise at higher frequencies, resulting in an increase in receiver sensitivity. The configuration shown in Figure 1 can create a Butterworth or Bessel response. The Butterworth filter offers a very flat amplitude response in the passband and a rolloff rate of 40dB/decade for the two-pole filter. The Bessel filter has a linear phase response, which works well for filtering digital data. To calculate the value of C5 and C6, use the following equations, along with the coefficients in Table 1: C5 = b a(100k)( π)(fC ) FILTER TYPE where fC is the desired 3dB corner frequency. For example, to choose a Butterworth filter response with a corner frequency of 5kHz: 1.000 (1.414)(100kΩ)(3.14)(5kHz) The suggested data slicer configuration uses a resistor (R1) connected between DSN and DSP with a capacitor (C4) from DSN to DGND (Figure 2). This configuration averages the analog output of the filter and sets the threshold to approximately 50% of that amplitude. With this configuration, the threshold automatically adjusts as the analog signal varies, minimizing the possibility for errors in the digital data. The values of R1 and C4 affect how fast the threshold tracks to the analog amplitude. Be sure to keep the corner frequency of the RC circuit much lower than the lowest expected data rate. Note that a long string of zeros or ones can cause the threshold to drift. This configuration works best if a coding scheme, such as Manchester coding, which has an equal number of zeros and ones, is used. To prevent continuous toggling of DATAOUT in the absence of an RF signal due to noise, add hysteresis to the data slicer as shown in Figure 3. Table 1. Coefficents to Calculate C5 and C6 a C6 = 4(100k)( π)(fC ) C5 = slicing threshold, which is applied to the second comparator input. a b Butterworth (Q = 0.707) 1.414 1.000 Bessel (Q = 0.577) 1.3617 0.618 ≈ 450pF MAX7034 1.414 C6 = ≈ 225pF k Ω 4 100 ( )( )(3.14)(5kHz) RSSI Choosing standard capacitor values changes C5 to 470pF and C6 to 220pF, as shown in the Typical Application Circuit. Data Slicer The data slicer takes the analog output of the data filter and converts it to a digital signal. This is achieved by using a comparator and comparing the analog input to a threshold voltage. One input is supplied by the data filter output. Both comparator inputs are accessible offchip to allow for different methods of generating the 10 RDF1 100kΩ RDF2 100kΩ 22 DFFB 21 OPP 19 DFO C6 C5 Figure 1. Sallen-Key Lowpass Data Filter ______________________________________________________________________________________ 315MHz/434MHz ASK Superheterodyne Receiver MAX7034 Peak Detector The peak-detector output (PDOUT), in conjunction with an external RC filter, creates a DC output voltage equal to the peak value of the data signal. The resistor provides a path for the capacitor to discharge, allowing the peak detector to dynamically follow peak changes of the data-filter output voltage. For faster data slicer response, use the circuit shown in Figure 4. For more details on hysteresis and peak-detector applications, refer to Maxim Application Note 3671, Data Slicing Techniques for UHF ASK Receivers. Layout Considerations A properly designed PCB is an essential part of any RF/microwave circuit. On high-frequency inputs and outputs, use controlled-impedance lines and keep them as short as possible to minimize losses and radiation. At high frequencies, trace lengths that are on the order of λ/10 or longer act as antennas. Keeping the traces short also reduces parasitic inductance. Generally, 1 inch of a PCB trace adds about 20nH of parasitic inductance. The parasitic inductance can have a dramatic effect on the effective inductance of a passive component. For example, a 0.5 inch trace connecting a 100nH inductor adds an extra 10nH of inductance or 10%. To reduce the parasitic inductance, use wider traces and a solid ground or power plane below the signal traces. Also, use low-inductance connections to ground on all GND pins, and place decoupling capacitors close to all VDD connections. MAX7034 DATA SLICER 25 DATAOUT 20 DSN 23 DSP R4 19 DFO R1 R3 R2 C4 *OPTIONAL Figure 3. Generating Data Slicer Hysteresis MAX7034 DATA SLICER 25 DATAOUT 20 DSN 23 DSP 19 DFO 26 PDOUT 25kΩ 47nF Figure 4. Using PDOUT for Faster Startup MAX7034 DATA SLICER 20 DSN 25 DATAOUT C4 23 DSP 19 DFO R1 Figure 2. Generating Data Slicer Threshold ______________________________________________________________________________________ 11 315MHz/434MHz ASK Superheterodyne Receiver MAX7034 Typical Application Circuit * C9 L1 L2 Y1 AT 315MHz DO NOT POPULATE 51nH 120nH 9.509375MHz AT 433.92MHz DO NOT POPULATE 27nH 56nH 13.225625MHz C14 15pF F_IN 1 +3.3V C7 100pF 2 3 4 5 C9 * 6 +3.3V C2 0.01μF L1 * 7 +3.3V +3.3V 1 3 PDOUT 2 JU6 11 SHDN 3 TP4 C13 OPEN DSN 1 2 JU4 LNASRC 3 AGND DATAOUT LNAOUT R5 10kΩ 25 TP8 DATA_OUT VDD AVDD 24 C23 0.01μF MIXIN1 MIXIN2 DSP 10 26 TP9 1 2 JU1 27 R2 OPEN VDD5 9 VDD 28 MAX7034 LNAIN C21 10pF C24 0.1μF R7 0Ω 23 C22 1000pF JU8 R6 OPEN AGND DFFB IRSEL VDD JU7 TP5 SHDN C8 100pF TP6 +3.3V AVDD C11 100pF 8 C10 220pF GND XTAL2 U1 L3 15nH +3.3V XTAL1 C12 0.1μF L2 * C19 OPEN C16 OPEN C18 OPEN RF_IN C15 15pF Y1 * OPP 22 21 TP7 C6 220pF C5 470pF DSN VDD DSN C20 0.1μF TP10 12 13 +3.3V 14 20 TP2 C4 0.47μF R1 5.1kΩ MIXOUT DFO DGND DVDD IFIN2 C1 0.01μF TP3 19 18 R8 10kΩ C3 1500pF 17 IFIN1 16 XTALSEL JU2 TP12 EN_REG 1 2 3 JU5 TP11 Y2 10.7MHz IN 3 2 1 2 R3 OPEN C17 OPEN MIX_OUT JU3 3 VDD 15 1 +3.3V R4 OPEN EN_REG GND OUT 1 2 3 Chip Information PROCESS: CMOS 12 ______________________________________________________________________________________ 315MHz/434MHz ASK Superheterodyne Receiver TSSOP4.40mm.EPS PACKAGE OUTLINE, TSSOP 4.40mm BODY 21-0066 I 1 1 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 © 2008 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc. MAX7034 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.)