MAX7033 315MHz/433MHz ASK Superheterodyne

MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
General Description
The MAX7033 fully integrated low-power CMOS superheterodyne receiver is ideal for receiving amplitude shiftkeyed (ASK) data in the 300MHz to 450MHz frequency
range. The receiver has an RF input signal range of
-114dBm to 0dBm. With few external components and a
low-current power-down mode, it is ideal for cost-sensitive
and power-sensitive applications typical in consumer
markets. The MAX7033 consists of a low-noise amplifier (LNA), a fully differential image-rejection mixer, an
on-chip phase-locked loop (PLL) with integrated voltagecontrolled oscillator (VCO), a 10.7MHz IF limiting amplifier
stage with received-signal-strength indicator (RSSI), and
analog baseband data-recovery circuitry. The MAX7033
also has a discrete one-step automatic gain control
(AGC) that reduces the LNA gain by 35dB when the RF
input signal exceeds -62dBm. The AGC circuitry offers an
externally controlled hold feature.
The MAX7033 is available in 28-pin TSSOP and 32-pin
TQFN packages and is specified over the extended
(-40°C to +105°C) temperature range.
Applications
●● Security Systems
●● Garage Door Openers
●● Home Automation
●● Remote Controls
●● Local Telemetry
●● Wireless Sensors
Features
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
Optimized for 315MHz or 433MHz Band
Operates from Single +3.3V or +5.0V Supplies
High Dynamic Range with On-Chip AGC
AGC Hold Circuit
1ms AGC Release Time
Selectable Image-Rejection Center Frequency
Selectable x64 or x32 fLO/fXTAL Ratio
Low 5.2mA Operating Supply Current
< 3.5μA Low-Current Power-Down Mode for Efficient
Power Cycling
250μs Startup Time
Built-In 44dB RF Image Rejection
Better than -114dBm Receive Sensitivity
-40°C to +105°C Operation
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX7033EUI+
-40°C to +105°C
28 TSSOP
MAX7033ETJ+
-40°C to +105°C
32 TQFN-EP*
+Denotes a lead(Pb)-free/RoHS-compliant package.
*EP = Exposed pad.
Typical Application Circuit appears at end of data sheet.
AGND 5
LNAOUT 6
25 DATAOUT
MAX7033
XTAL1
XTAL2
SHDN
PDOUT
N.C.
28
27
26
25
+
N.C.
1
24
DATAOUT
24 VDD5
AGND
2
23
VDD5
23 DSP
LNAOUT
3
22
DSP
21
N.C.
20
DFFB
AVDD 7
22 DFFB
AVDD
4
MIXIN1 8
21 OPP
MIXIN1
5
MIXIN2 9
20 DSN
MIXIN2
6
19
OPP
AGND 10
19 DFO
AGND
7
18
DSN
IRSEL 11
18 IFIN2
IRSEL
8
17
DFO
MIXOUT 12
17 IFIN1
9
11
12
13
14
15
16
DVDD
AC
N.C.
XTALSEL
IFIN1
IFIN2
15 AC
10
TSSOP
16 XTALSEL
DGND
DVDD 14
MAX7033
MIXOUT
DGND 13
19-3273; Rev 4; 4/14
AVDD
26 PDOUT
LNASRC 4
29
27 SHDN
LNAIN 3
LNAIN
28 XTAL2
AVDD 2
30
+
LNASRC
XTAL1 1
31
TOP VIEW
32
Pin Configurations
TQFN
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Absolute Maximum Ratings
VDD5 to AGND......................................................-0.3V to +6.0V
AVDD to AGND.....................................................-0.3V to +4.0V
DVDD to DGND.....................................................-0.3V to +4.0V
AGND to DGND....................................................-0.1V to +0.1V
IRSEL, DATAOUT, XTALSEL,
AC, SHDN to AGND............................ -0.3V to (VDD5 + 0.3V)
All Other Pins to AGND.........................-0.3V to (VDVDD + 0.3V)
Continuous Power Dissipation (TA = +70°C)
28-Pin TSSOP (derate 12.8mW/°C above +70°C).. 1025.6mW
32-Thin QFN (derate 21.3mW/°C above +70°C)....1702.1mW
Operating Temperature Range.......................... -40°C to +105°C
Junction Temperature.......................................................+150°C
Storage Temperature Range............................. -60°C to +150°C
Lead Temperature (soldering 10s)...................................+300°C
Soldering Temperature (reflow)........................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
DC Electrical Characteristics (+3.3V Operation)
(Typical Application Circuit, VAVDD = VDVDD = VDD5 = +3.0V to +3.6V, no RF signal applied, TA = -40°C to +105°C, unless otherwise
noted. Typical values are at VAVDD = VDVDD = VDD5 = +3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Supply Voltage
VAVDD,
VDVDD
Supply Current
IDD
Shutdown Supply Current
ISHDN
Input-Voltage Low
VIL
Input-Voltage High
VIH
Input Logic Current High
IIH
CONDITIONS
MIN
TYP
MAX
UNITS
+3.3V nominal supply voltage
3.0
3.3
3.6
V
fRF = 315MHz
5.2
6.23
fRF = 433MHz
5.7
6.88
fRF = 315MHz
2.6
fRF = 433MHz
3.5
VSHDN = VDVDD
VSHDN = 0V,
VXTALSEL = 0V
0.4
VDVDD - 0.4
fRF = 375MHz, VIRSEL = VDD5/2
VOL
ISINK = 10µA
DATAOUT Output-Voltage High
VOH
ISOURCE = 10µA
V
µA
VDD5 - 0.4
1.1
VDD5 - 1.0
fRF = 315MHz, VIRSEL = 0V
DATAOUT Output-Voltage Low
µA
V
10
fRF = 433MHz, VIRSEL = VDD5
Image-Reject Select Voltage
(Note 2)
8.0
mA
V
0.4
0.125
V
VDVDD - 0.125
V
DC Electrical Characteristics (+5.0V Operation)
(Typical Application Circuit, VDD5 = +4.5V to +5.5V, no RF signal applied, TA = -40°C to +105°C, unless otherwise noted. Typical
values are at VDD5 = +5.0V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
+5.0V nominal supply voltage
4.5
5.0
5.5
V
Supply Voltage
VDD5
Supply Current
IDD
VSHDN = VDD5
ISHDN
VSHDN = 0V,
VXTALSEL = 0V
Shutdown Supply Current
Input-Voltage Low
www.maximintegrated.com
VIL
fRF = 315MHz
5.2
6.4
fRF = 433MHz
5.7
6.76
fRF = 315MHz
3.7
fRF = 433MHz
4.2
9.8
0.4
mA
µA
V
Maxim Integrated │ 2
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Electrical Characteristics (continued)
(Typical Application Circuit, VDD5 = +4.5V to +5.5V, no RF signal applied, TA = -40°C to +105°C, unless otherwise noted. Typical
values are at VDD5 = +5.0V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Input-Voltage High
VIH
Input Logic Current High
IIH
CONDITIONS
TYP
MAX
fRF = 375MHz, VIRSEL = VDD5/2
µA
VDD5 - 0.4
1.1
VDD5 - 1.5
fRF = 315MHz, VIRSEL = 0V
DATAOUT Output-Voltage Low
VOL
ISINK = 10µA
DATAOUT Output-Voltage High
VOH
ISOURCE = 10µA
UNITS
V
15
fRF = 433MHz, VIRSEL = VDD5
Image-Reject Select Voltage
(Note 2)
MIN
VDD5 - 0.4
V
0.4
0.125
V
VDD5 - 0.125
V
AC Electrical Characteristics
(Typical Application Circuit, VAVDD = VDVDD = VDD5 = +3.0V to +3.6V, all RF inputs are referenced to 50Ω, fRF = 315MHz,
TA = -40°C to +105°C, unless otherwise noted. Typical values are at VAVDD = VDVDD = VDD5 = +3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
GENERAL CHARACTERISTICS
Startup Time
tON
Receiver Input Frequency
fRF
Maximum Receiver Input Level
Time for valid signal detection after VSHDN
= VDVDD
300
Modulation depth > 18dB
Sensitivity (Note 3)
AGC Hysteresis
Maximum Data Rate
250
µs
450
0
Average carrier power level
-120
Peak power level
-114
MHz
dBm
dBm
LNA gain from low to high
8
dB
Switching time from low to high gain
1
ms
Manchester coded
33
NRZ coded
66
kbps
LNA IN HIGH-GAIN MODE
1 - j3.4
fRF = 375MHz
1 - j3.9
fRF = 315MHz
1 - j4.7
Input Impedance
ZIN_LNA
1dB Compression Point
P1dBLNA
-22
dBm
IIP3LNA
-12
dBm
-80
dBm
3
dB
Input-Referred 3rd-Order Intercept
LO Signal Feedthrough to
Antenna
Noise Figure
www.maximintegrated.com
NFLNA
Normalized to 50Ω
fRF = 433MHz
Maxim Integrated │ 3
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Electrical Characteristics (continued)
(Typical Application Circuit, VAVDD = VDVDD = VDD5 = +3.0V to +3.6V, all RF inputs are referenced to 50Ω, fRF = 315MHz,
TA = -40°C to +105°C, unless otherwise noted. Typical values are at VAVDD = VDVDD = VDD5 = +3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
LNA IN LOW-GAIN MODE
Input Impedance
1dB Compression Point
Input-Referred 3rd-Order Intercept
ZIN_LNA
Normalized to 50Ω
(Note 4)
fRF = 433MHz
1 - j3.4
fRF = 375MHz
1 - j3.9
fRF = 315MHz
1 - j4.7
P1dBLNA
-10
dBm
IIP3LNA
-7
dBm
-80
dBm
3
dB
35
dB
IIP3MIX
-18
dBm
ZOUT_MIX
330
Ω
NFMIX
16
dB
LO Signal Feedthrough to
Antenna
Noise Figure
NFLNA
Voltage-Gain Reduction
AGC enabled (depends on tank Q)
MIXER
Input-Referred 3rd-Order Intercept
Output Impedance
Noise Figure
Image Rejection
(Not Including LNA Tank)
LNA/Mixer Voltage Gain
fRF = 433MHz, VIRSEL = VDVDD
42
fRF = 375MHz, VIRSEL = VDVDD/2
44
fRF = 315MHz, VIRSEL = 0V
44
330Ω IF filter load
LNA in high-gain mode
48
LNA in low-gain mode
13
dB
dB
INTERMEDIATE FREQUENCY (IF)
Input Impedance
330
Ω
10.7
MHz
3dB Bandwidth
10
MHz
RSSI Linearity
±0.5
dB
80
dB
Operating Frequency
ZIN_IF
fIF
Bandpass response
RSSI Dynamic Range
RSSI Level
AGC Threshold
PRFIN < -120dBm
1.15
PRFIN > 0dBm, AGC enabled
2.2
LNA gain from low to high
1.39
LNA gain from high to low
1.98
V
V
DATA FILTER
Maximum Bandwidth
50
kHz
100
kHz
DATA SLICER
Comparator Bandwidth
www.maximintegrated.com
Maxim Integrated │ 4
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Electrical Characteristics (continued)
(Typical Application Circuit, VAVDD = VDVDD = VDD5 = +3.0V to +3.6V, all RF inputs are referenced to 50Ω, fRF = 315MHz,
TA = -40°C to +105°C, unless otherwise noted. Typical values are at VAVDD = VDVDD = VDD5 = +3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Maximum Load Capacitance
CONDITIONS
MIN
CLOAD
TYP
MAX
UNITS
10
pF
Output High Voltage
VDD5
V
Output Low Voltage
0
V
CRYSTAL OSCILLATOR
fRF = 433MHz
Crystal Frequency (Note 5)
fXTAL
fRF = 315MHz
VXTALSEL = 0V
6.6128
VXTALSEL = VDD5
13.2256
VXTALSEL = 0V
4.7547
VXTALSEL = VDD5
9.5094
Crystal Tolerance
Input Capacitance
From each pin to ground
MHz
50
ppm
6.2
pF
Note 1: 100% tested at TA = +25°C. Guaranteed by design and characterization over temperature.
Note 2: IRSEL is internally set to 375MHz IR mode. It can be left open when the 375MHz image-rejection setting is desired. Bypass
to AGND with a 1nF capacitor in a noisy environment.
Note 3: BER = 2 x 10-3, Manchester encoded, data rate = 4kbps, IF bandwidth = 280kHz.
Note 4: Input impedance is measured at the LNAIN pin. Note that the impedance includes the 15nH inductive degeneration connected from the LNA source to ground. The equivalent input circuit is 50Ω in series with 2.2pF.
Note 5: Crystal oscillator frequency for other RF carrier frequency within the 300MHz to 450MHz range is (fRF - 10.7MHz)/64 for
VXTALSEL = 0V, and (fRF - 10.7MHz)/32 for XTALSEL = VDD5.
Typical Operating Characteristics
(Typical Application Circuit, VAVDD = VDVDD = VDD5 = +3.3V, fRF = 315MHz, TA = +25°C, unless otherwise noted.)
SUPPLY CURRENT
vs. RF FREQUENCY
+85°C
5.4
5.2
5.0
4.8
4.6
+25°C
4.4
-40°C
4.2
4.0
3.0
3.1
3.2
3.3
5.5
5.0
+85°C
4.5
+25°C
4.0
-40°C
fRF = 433MHz
10
1
MAX7033 toc03
+105°C
6.0
fRF = 315MHz
0.1
3.5
3.4
SUPPLY VOLTAGE (V)
www.maximintegrated.com
6.5
100
MAX7033 toc02
+105°C
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
5.8
5.6
7.0
MAX7033 toc01
6.0
BIT-ERROR RATE
vs. AVERAGE CARRIER POWER
BIT-ERROR RATE (%)
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
3.5
3.6
3.0
250
300
350
400
RF FREQUENCY (MHz)
450
500
0.01
-130 -128 -126 -124 -122 -120 -118 -116 -114
AVERAGE CARRIER POWER (dBm)
Maxim Integrated │ 5
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Typical Operating Characteristics (continued)
(Typical Application Circuit, VAVDD = VDVDD = VDD5 = +3.3V, fRF = 315MHz, TA = +25°C, unless otherwise noted.)
35
SYSTEM GAIN (dB)
85
-140 -120 -100
-80
-60
-40
RF INPUT POWER (dBm)
LNA/MIXER VOLTAGE GAIN
vs. IF FREQUENCY
IMAGE REJECTION
vs. RF FREQUENCY
45
35
49dB IMAGE
REJECTION
25
15
LOWER
SIDEBAND
FROM RFIN
TO MIXOUT
fRF = 315MHz
5
5
10
15
20
IF FREQUENCY (MHz)
www.maximintegrated.com
25
55
50
40
30
1.5
1.8
0.5
1.6
-1.5
RSSI
-90
-70
-2.5
-50
-30
-10
10
-3.5
IF INPUT POWER (dBm)
IMAGE REJECTION
vs. TEMPERATURE
fRF = 375MHz
fRF = 315MHz
fRF = 433MHz
280 300 320 340 360 380 400 420 440 460 480
RF FREQUENCY (MHz)
-0.5
DELTA
45.0
fRF = 315MHz
44.5
44.0
43.5
43.0
fRF = 375MHz
42.5
42.0
fRF = 433MHz
41.5
41.0
40.5
-40
-15
10
35
60
85
TEMPERATURE (°C)
Maxim Integrated │ 6
DELTA (%)
2.0
1.0
0
45
35
30
-20
MAX7033 toc08
UPPER
SIDEBAND
0
1.0
110
TEMPERATURE (°C)
55
-5
60
2.5
1.2
IMAGE REJECTION (dB)
10
IMAGE REJECTION (dB)
65
-15
3.5
2.2
1.4
1.2
MAX7033 toc07
-40
1.6
1.4
fRF = 315MHz
-122
-124
VAC = 0V
MAX7033 toc06
MAX7033 toc09
-118
1.8
RSSI (V)
-116
-120
2.4
2.0
fRF = 433MHz
-114
VAC = VDVDD
2.2
RSSI (V)
SENSITIVITY (dBm)
-112
IF BANDWIDTH = 280kHz
MAX7033 toc05
AVERAGE CARRIER POWER
0.2% BER
IF BANDWIDTH = 280kHz
-110
2.4
MAX7033 toc04
-108
RSSI AND DELTA
vs. IF INPUT POWER
RSSI vs. RF INPUT POWER
SENSITIVITY vs. TEMPERATURE
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Typical Operating Characteristics (continued)
(Typical Application Circuit, VAVDD = VDVDD = VDD5 = +3.3V, fRF = 315MHz, TA = +25°C, unless otherwise noted.)
40
30
-10
-15
-20
10
1
200MHz
-20
315MHz
-36dB
FREQUENCY (MHz)
REGULATOR VOLTAGE
vs. REGULATOR CURRENT
PHASE NOISE
vs. OFFSET FREQUENCY
0
MAX7033 toc13
2.9
-40°C
2.7
+25°C
2.5
2.3
+85°C
2.1
+105°C
1.9
10
20
30
40
50
REGULATOR CURRENT (mA)
www.maximintegrated.com
fRF = 315MHz
-20
PHASE NOISE (dBc/Hz)
3.1
0
0 100 200 300 400 500 600 700 800 900 1000
IF FREQUENCY (MHz)
3.3
REGULATOR VOLTAGE (V)
0
-10
-50
100
-40
-60
-80
-100
-120
60
500MHz
315MHz
-40
3.5
1.7
10
-140
PHASE NOISE
vs. OFFSET FREQUENCY
0
fRF = 433MHz
-20
PHASE NOISE (dBc/Hz)
-30
WITH INPUT
MATCHING
20
-30
-25
MAX7033 toc12
MAX7033 toc15
S11 MAGNITUDE (dB)
-5
S11 SMITH CHART PLOT OF RFIN
S11 LOG MAGNITUDE PLOT OF RFIN
MAX7033 toc14
0
NORMALIZED IF GAIN (dB)
50
MAX7033 toc10
5
MAX7033 toc11
NORMALIZED IF GAIN
vs. IF FREQUENCY
-40
-60
-80
-100
-120
10
100
1k
10k
100k
OFFSET FREQUENCY (Hz)
1M
10M
-140
10
100
1k
10k
100k
1M
10M
OFFSET FREQUENCY (Hz)
Maxim Integrated │ 7
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Pin Description
PIN
TSSOP
TQFN
1
29
NAME
FUNCTION
XTAL1
Crystal Input 1 (see the Phase-Locked Loop section)
2, 7
4, 30
AVDD
Positive Analog Supply Voltage. For +5V operation, pin 2 is the output of an on-chip +3.2V
low-dropout regulator, and should be bypassed to AGND with a 0.1µF capacitor as close
as possible to the pin. Pin 7 must be externally connected to the supply from pin 2, and
bypassed to AGND with a 0.01µF capacitor as close as possible to the pin (see the Voltage
Regulator section and the Typical Application Circuit).
3
31
LNAIN
Low-Noise Amplifier Input (see the Low-Noise Amplifier section)
4
32
LNASRC
5, 10
2, 7
AGND
6
3
LNAOUT
8
5
MIXIN1
1st Differential Mixer Input. Connect to LC tank filter from LNAOUT.
9
6
MIXIN2
2nd Differential Mixer Input. Connect through a 100pF capacitor to VDD3 side of the LC tank.
11
8
IRSEL
Image-Rejection Select. Set VIRSEL = 0V to center image rejection at 315MHz. Leave IRSEL
unconnected to center image rejection at 375MHz. Set VIRSEL = VDD5 to center image
rejection at 433MHz.
12
9
MIXOUT
13
10
DGND
Digital Ground
14
11
DVDD
Positive Digital Supply Voltage. Connect to both of the AVDD pins. Bypass to DGND with a
0.01µF capacitor as close as possible to the pin (see the Typical Application Circuit).
15
12
AC
16
14
XTALSEL
Crystal Divider Ratio Select. Drive XTALSEL low to select fLO/fXTAL ratio of 64, or drive
XTALSEL high to select fLO/fXTAL ratio of 32.
17
15
IFIN1
1st Differential Intermediate-Frequency Limiter Amplifier Input. Bypass to AGND with a
1500pF capacitor as close to the pin as possible.
18
16
IFIN2
2nd Differential Intermediate-Frequency Limiter Amplifier Input. Connect to the output of a
10.7MHz bandpass filter.
19
17
DFO
Data Filter Output
20
18
DSN
Negative Data Slicer Input
21
19
OPP
Noninverting Op-Amp Input for the Sallen-Key Data Filter
22
20
DFFB
Data-Filter Feedback Node. Input for the feedback of the Sallen-Key data filter.
23
22
DSP
Positive Data Slicer Input
+5V Supply Voltage. Bypass to AGND with a 0.01µF capacitor as close as possible to the
pin. For +5V operation, VDD5 is the input to an on-chip voltage regulator whose +3.2V output
appears at the pin 2 AVDD pin (see the Voltage Regulator section and the Typical Application
Circuit).
24
23
VDD5
25
24
DATAOUT
26
26
PDOUT
27
27
SHDN
www.maximintegrated.com
Low-Noise Amplifier Source for External Inductive Degeneration. Connect inductor to ground
to set the LNA input impedance (see the Low-Noise Amplifier section).
Analog Ground
Low-Noise Amplifier Output. Connect to mixer input through an LC tank filter (see the LowNoise Amplifier section).
330Ω Mixer Output. Connect to the input of the 10.7MHz bandpass filter.
Automatic Gain Control. See Figure 1. Internally pulled down to AGND with a 100kΩ resistor.
Digital Baseband Data Output
Peak-Detector Output
Power-Down Select Input. Drive high to power up the IC. Internally pulled down to AGND with
a 100kΩ resistor.
Maxim Integrated │ 8
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Pin Description (continued)
PIN
NAME
TSSOP
TQFN
28
28
XTAL2
—
1, 13,
21, 25
N.C.
—
—
EP
FUNCTION
Crystal Input 2. Can also be driven with an external reference oscillator (see the Crystal
Oscillator section).
No Connection
Exposed Pad (TQFN Only). Connect EP to GND.
Functional Diagram
LNASRC
4
LNAIN
AVDD
VDD5
AVDD
DVDD
DGND
AGND
3
AC
15
IRSEL
11
LNAOUT MIXIN1 MIXIN2
6
8
9
AUTOMATIC
GAIN
CONTROL
LNA
Q
3.2V REG
IFIN1
17
28-PIN TSSOP
PACKAGE
IFIN2
18
0˚
IMAGE
REJECTION
2
24
MIXOUT
12
I
IF LIMITING
AMPS
∑
90˚
MAX7033
RSSI
7
14
13
DIVIDE
BY 64
VCO
PHASE
DETECTOR
LOOP
FILTER
5, 10
÷1
÷2
CRYSTAL
DRIVER
XTALSEL
XTAL1 XTAL2
16
1
28
DATA
FILTER
RDF2
100kΩ
DATA
SLICER
POWERDOWN
27
SHDN
RDF1
100kΩ
25
DATAOUT
Detailed Description
The MAX7033 CMOS superheterodyne receiver and a few
external components provide the complete receive chain
from the antenna to the digital output data. Depending on
signal power and component selection, data rates as high
as 33kbps Manchester (66kbps NRZ) can be achieved.
The MAX7033 is designed to receive binary ASK data
modulated in the 300MHz to 450MHz frequency range.
ASK modulation uses a difference in amplitude of the carrier to represent logic 0 and logic 1 data.
20
23
19
DSN DSP DFO
26
21
22
PDOUT
OPP
DFFB
connect VDD5 to the supply voltage. An on-chip voltage
regulator drives one of the AVDD pins to approximately
+3.2V. For proper operation, DVDD and both the AVDD
pins must be connected together. Bypass VDD5, DVDD,
and the pin 7 AVDD pin to AGND with 0.01μF capacitors,
and the pin 2 AVDD pin to AGND with a 0.1μF capacitor,
all placed as close as possible to the pins.
Low-Noise Amplifier
Voltage Regulator
The LNA is an nMOS cascode amplifier with off-chip
inductive degeneration, with a 3.0dB noise figure and an
IIP3 of -12dBm. The gain and noise figures are dependent
on both the antenna matching network at the LNA input
and the LC tank network between the LNA output and the
mixer inputs.
www.maximintegrated.com
Maxim Integrated │ 9
For operation with a single +3.0V to +3.6V supply voltage,
connect AVDD, DVDD, and VDD5 to the supply voltage.
For operation with a single +4.5V to +5.5V supply voltage,
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
The off-chip inductive degeneration is achieved by connecting an inductor from LNASRC to AGND. This inductor
sets the real part of the input impedance at LNAIN, allowing for a more flexible input impedance match, such as a
typical PCB trace antenna. A nominal value for this inductor with a 50Ω input impedance is 15nH, but is affected
by PCB trace.
The LC tank filter connected to LNAOUT comprises L3
and C2 (see the Typical Application Circuit). Select L3
and C2 to resonate at the desired RF input frequency. The
resonant frequency is given by:
f RF =
1
resistor. The resistor reduces the LNA gain by 35dB,
thereby reducing the RSSI output by about 500mV. The
LNA resumes high-gain mode when the RSSI level drops
back below 1.39V (approximately -70dBm at RF input)
for 1ms. The AGC has a hysteresis of 8dB. With the AGC
function, the MAX7033 can reliably produce an ASK output for RF input levels up to 0dBm with modulation depth
of 18dB.
When the AC pin is high and SHDN goes high, the AGC
circuit is disabled and the LNA is always in high gain
mode. The AGC function can be resumed by bringing the
AC pin low when SHDN is high.
The MAX7033 features an AGC lock function that is
asserted when the level at the AC pin transitions from
low to high while SHDN is high. Locking the AGC locks
the LNA in the current gain state. As shown in Figure 1,
the AGC lock function can be enabled or disabled as long
as the SHDN pin is high. Changing the state of AC when
SHDN is low has no effect.
2 π L TOTAL × C TOTAL
where:
LTOTAL = L3 + LPARASITICS.
CTOTAL = C2 + CPARASITICS.
LPARASITICS and CPARASITICS include inductance and
capacitance of the PCB traces, package pins, mixer input
impedance, LNA output impedance, etc. These parasitics
at high frequencies cannot be ignored, and can have a
dramatic effect on the tank filter center frequency. Lab
experimentation should be done to optimize the center
frequency of the tank.
Mixer
Automatic Gain Control
The mixer cell is a pair of double balanced mixers that
perform an IQ downconversion of the RF input to the
10.7MHz IF from a low-side injected LO (i.e., fLO = fRF
- fIF). The image-rejection circuit then combines these signals to achieve 44dB of image rejection. Low-side injection
When the AC pin is low, the automatic gain-control (AGC)
circuit monitors the RSSI output. As the RSSI output
reaches 1.98V, which corresponds to RF input level of
-62dBm, the AGC switches on the LNA gain reduction
A unique feature of the MAX7033 is the integrated image
rejection of the mixer. This device eliminates the need
for a costly front-end SAW filter for most applications.
Advantages of not using a SAW filter are increased sensitivity, simplified antenna matching, less board space,
and lower cost.
VIH
SHDN
PIN
VIL
VIH
AC PIN
VIL
AGC
LOCK
AGC
UNLOCK
AGC
LOCK
AGC ENABLED
AGC
UNLOCK
NO
EFFECT
NO
EFFECT
NO
EFFECT
AGC
DISABLED
AGC
ENABLED
AGC
DISABLED
Figure 1. AGC Lock Activation Cycles
www.maximintegrated.com
Maxim Integrated │ 10
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
is required due to the on-chip image-rejection architecture. The IF output is driven by a source follower biased to
create a driving-point impedance of 330Ω; this provides a
good match to the off-chip 330Ω ceramic IF filter.
The IRSEL pin is a logic input that selects one of the
three possible image-rejection frequencies. When VIRSEL
= 0V, the image rejection is tuned to 315MHz. VIRSEL =
VDD5/2 tunes the image rejection to 375MHz, and VIRSEL
= VDD5 tunes the image rejection to 433MHz. The IRSEL
pin is internally set to VDD5/2 (image rejection at 375MHz)
when it is left unconnected, thereby eliminating the need
for an external VDD5/2 voltage.
Phase-Locked Loop
The PLL block contains a phase detector, charge pump,
integrated loop filter, VCO, asynchronous 64x clock
divider, and crystal oscillator driver. Besides the crystal,
this PLL does not require any external components. The
VCO generates a low-side LO. The relationship between
the RF, IF, and crystal frequencies is given by:
f -f
f XTAL = RF IF
32 × M
where:
M = 1 (VXTALSEL = VDD5) or 2 (VXTALSEL = 0V)
To allow the smallest possible IF bandwidth (for best sensitivity), minimize the tolerance of the reference crystal.
Table 1. Component Values for Typical Application Circuit
COMPONENT
VALUE FOR fRF = 433MHz
VALUE FOR fRF = 315MHz
DESCRIPTION
C1
100pF
100pF
5%
C2
2pF
4pF
± 0.1pF
C3
100pF
100pF
5%
C4
100pF
100pF
5%
C5
1500pF
1500pF
10%
C6
220pF
220pF
5%
C7
470pF
470pF
5%
C8
0.47µF
0.47µF
20%
C9
220pF
220pF
10%
C10
0.01µF
0.01µF
20%
C11
0.1µF
0.1µF
20%
C12
15pF
15pF
Depends on XTAL
C13
15pF
15pF
Depends on XTAL
C14
0.01µF
0.01µF
20%
C15
0.01µF
0.01µF
20%
L1
56nH
120nH
5% or better*
L2
15nH
15nH
5% or better*
L3
15nH
27nH
5% or better*
R1
5.1kΩ
5.1kΩ
5%
R2
Open
Open
—
R3
Short
Short
—
X1 (÷64)
6.6128MHz**
4.7547MHz**
Crystek or Hong Kong Crystal
X1 (÷32)
13.2256MHz**
9.5094MHz**
Crystek or Hong Kong Crystal
Y1
10.7MHz ceramic filter
10.7MHz ceramic filter
Murata
*Wire wound recommended.
**Crystal frequencies shown are for ÷64 (VXTALSEL = 0V) and ÷32 (VXTALSEL = VDD)
www.maximintegrated.com
Maxim Integrated │ 11
MAX7033
Intermediate Frequency and RSSI
The IF section presents a differential 330Ω load to provide
matching for the off-chip ceramic filter. The six internal
AC-coupled limiting amplifiers produce an overall gain of
approximately 65dB, with a bandpass-filter-type response
centered near the 10.7MHz IF frequency 1 with a 3dB
bandwidth of approximately 10MHz. The RSSI circuit
demodulates the IF by producing a DC output proportional to the log of the IF signal level, with a slope of
approximately 14.2mV/dB (see the Typical Operating
Characteristics).
Applications Information
Crystal Oscillator
The crystal oscillator in the MAX7033 is designed to
present a capacitance of approximately 3pF between the
XTAL1 and XTAL2. If a crystal designed to oscillate with
a different load capacitance is used, the crystal is pulled
away from its stated operating frequency, introducing an
error in the reference frequency. Crystals designed to
operate with higher differential load capacitance always
pull the reference frequency higher. For example, a
4.7547MHz crystal designed to operate with a 10pF load
capacitance oscillates at 4.7563MHz with the MAX7033,
causing the receiver to be tuned to 315.1MHz rather than
315.0MHz, an error of about 100kHz, or 320ppm.
In actuality, the oscillator pulls every crystal. The crystal’s
natural frequency is really below its specified frequency,
but when loaded with the specified load capacitance, the
crystal is pulled and oscillates at its specified frequency.
This pulling is already accounted for in the specification of
the load capacitance. Additional pulling can be calculated
if the electrical parameters of the crystal are known. The
frequency pulling is given by:
fP

CM 
1
1
6

 × 10
2  C CASE + C LOAD C CASE + C SPEC 
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
It is possible to use an external reference oscillator in
place of a crystal to drive the VCO. AC-couple the external oscillator to XTAL2 with a 1000pF capacitor. Drive
XTAL2 with a signal level of approximately -10dBm.
AC-couple XTAL1 to ground with a 1000pF capacitor.
Data Filter
The data filter is implemented as a 2nd-order lowpass
Sallen-Key filter. The pole locations are set by the
combination of two on-chip resistors and two external
capacitors. Adjusting the value of the external capacitors
changes the corner frequency to optimize for different
data rates. The corner frequency should be set to approximately 1.5 times the fastest expected data rate from the
transmitter. Keeping the corner frequency near the data
rate rejects any noise at higher frequencies, resulting in
an increase in receiver sensitivity.
The configuration shown in Figure 2 can create a
Butterworth or Bessel response. The Butterworth filter
offers a very flat amplitude response in the passband and
a rolloff rate of 40dB/decade for the two-pole filter. The
Bessel filter has a linear phase response, which works
well for filtering digital data. To calculate the value of C5
and C6, use the following equations, along with the coefficients in Table 2:
C5 =
b
a(100k)(π)(f C )
C6 =
a
4(100k )(π)(f C )
where fC is the desired 3dB corner frequency.
Table 2. Coefficents to Calculate C5 and C6
FILTER TYPE
a
b
Butterworth (Q = 0.707)
1.414
1.000
Bessel (Q = 0.577)
1.3617
0.618
where:
MAX7033
fP is the amount the crystal frequency pulled in ppm.
CM is the motional capacitance of the crystal.
RSSI
RDF1
100kΩ
RDF2
100kΩ
CCASE is the case capacitance.
CSPEC is the specified load capacitance.
CLOAD is the actual load capacitance.
When the crystal is loaded as specified, i.e., CLOAD =
CSPEC, the frequency pulling equals zero.
19
DFO
C6
21
OPP
C5
22
DFFB
Figure 2. Sallen-Key Lowpass Data Filter
www.maximintegrated.com
Maxim Integrated │ 12
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
For example, to choose a Butterworth filter response with
a corner frequency of 5kHz:
C5
C6
=
MAX7033
1.000
≈ 450pF
1.414
100k
Ω)(3.14)(5kHz)
(
)(
DATA
SLICER
1.414
≈ 225pF
(4)(100kΩ)(3.14)(5kHz)
20
DSN
25
DATAOUT
Choosing standard capacitor values changes C5 to 470pF
and C6 to 220pF, as shown in the Typical Application
Circuit.
The data slicer takes the analog output of the data filter
and converts it to a digital signal. This is achieved by using
a comparator and comparing the analog input to a threshold voltage. One input is supplied by the data filter output.
Both comparator inputs are accessible offchip to allow
for different methods of generating the slicing threshold,
which is applied to the second comparator input.
The suggested data slicer configuration uses a resistor
(R1) connected between DSN and DSP with a capacitor
(C4) from DSN to DGND (Figure 3). This configuration
averages the analog output of the filter and sets the
threshold to approximately 50% of that amplitude. With
this configuration, the threshold automatically adjusts as
the analog signal varies, minimizing the possibility for
errors in the digital data. The values of R1 and C4 affect
how fast the threshold tracks to the analog amplitude. Be
sure to keep the corner frequency of the RC circuit much
lower than the lowest expected data rate.
Note that a long string of zeros or ones can cause the
threshold to drift. This configuration works best if a coding
scheme, such as Manchester coding, which has an equal
number of zeros and ones, is used.
Figure 3. Generating Data Slicer Threshold
MAX7033
DATA
SLICER
25
DATAOUT
R2
20
DSN
23
DSP
R1
R4
19
DFO
R3
C4
*OPTIONAL
Figure 4. Generating Data Slicer Hysteresis
MAX7033
To prevent continuous toggling of DATAOUT in the
absence of an RF signal due to noise, add hysteresis to
the data slicer as shown in Figure 4.
DATA
SLICER
Peak Detector
The peak-detector output (PDOUT), in conjunction with
an external RC filter, creates a DC output voltage equal
to the peak value of the data signal. The resistor provides
a path for the capacitor to discharge, allowing the peak
detector to dynamically follow peak changes of the datafilter output voltage. For faster data slicer response, use
the circuit shown in Figure 5.
R1
C4
Data Slicer
19
DFO
23
DSP
25
DATAOUT
20
DSN
23
DSP
25kΩ
19
DFO
26
PDOUT
47nF
Figure 5. Using PDOUT for Faster Startup
www.maximintegrated.com
Maxim Integrated │ 13
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Layout Considerations
A properly designed PCB is an essential part of any RF/
microwave circuit. On high-frequency inputs and outputs,
use controlled-impedance lines and keep them as short
as possible to minimize losses and radiation. At high
frequencies, trace lengths that are on the order of λ/10 or
longer act as antennas.
Keeping the traces short also reduces parasitic inductance. Generally, 1in of a PCB trace adds about 20nH of
parasitic inductance. The parasitic inductance can have
a dramatic effect on the effective inductance of a passive component. For example, a 0.5in trace connecting a
100nH inductor adds an extra 10nH of inductance or 10%.
To reduce the parasitic inductance, use wider traces and
a solid ground or power plane below the signal traces.
Also, use low-inductance connections to ground on all
GND pins, and place decoupling capacitors close to all
power-supply pins.
Control Interface Considerations
When operating the MAX7033 with a +4.5V to +5.5V supply voltage, the SHDN and AC pins can be driven by a
microcontroller with either 3V or 5V interface logic levels.
When operating the MAX7033 with a +3.0V to +3.6V supply, only 3V logic from the microcontroller is allowed.
Typical Application Circuit
VDD3
IF VDD IS
VDD
(SEE TABLE)
THEN VDD3 IS
3.0V TO 3.6V CONNECTED TO VDD
CREATED BY LDO,
4.5V TO 5.5V AVAILABLE AT AVDD
(PIN 2)
X1
C11
C13
RF INPUT
1
2
C1
L1
3
4
L2
5
C14
VDD3
7
L3
C2
6
C3
8
9
C9
C4
10
11
12
13
14
**
C10
COMPONENT VALUES
IN TABLE 1
**SEE THE MIXER SECTION.
www.maximintegrated.com
XTAL1
XTAL2
AVDD
SHDN
LNAIN
LNASRC
MAX7033
PDOUT
DATAOUT
AGND
VDD5
LNAOUT
DSP
AVDD
DFFB
MIXIN1
OPP
MIXIN2
DSN
AGND
DFO
IRSEL
IFIN2
MIXOUT
IFIN1
DGND
XTALSEL
DVDD
AC
28
TO/FROM µP
POWER-DOWN
DATA OUT
27
26
R2
25
C15
24
R3
23
22
21
C7
20
19
18
17
R1
16
15
*
Y1
C12
C5
C6
C8
FROM P
IF FILTER
IN
OUT
GND
*SEE PHASE-LOCKED LOOP SECTION.
Maxim Integrated │ 14
MAX7033
Chip Information
PROCESS: CMOS
www.maximintegrated.com
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maximintegrated.com/packages. Note
that a “+”, “#”, or “-” in the package code indicates RoHS status
only. Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
28 TSSOP
U28+1
21-0066
90-0171
32 TQFN-EP
T3255+3
21-0140
90-0001
Maxim Integrated │ 15
MAX7033
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
Revision History
REVISION
NUMBER
REVISION
DATE
0
7/04
Initial release
1/11
Updated Ordering Information, Pin Configurations, Absolute Maximum Ratings,
DC Electrical Characteristics, AC Electrical Characteristics, Typical Operating
Characteristics, Pin Description, Functional Diagram, Voltage Regulator and
Layout Considerations sections, Typical Application Circuit, Chip Information, and
Package Information
1–9, 13, 14, 15
2
9/11
Updated input impedance values in AC Electrical Characteristics table; updated
TOC3 and TOC4 labels in Typical Operating Characteristics; clarified equations
in Pin Description and Phase-Locked Loop and Crystal Oscillator sections;
updated components in Table 1; and added new Control Interface Considerations
section
3–6, 11–14
3
4/14
Updated Applications and General Description
1
PAGES
CHANGED
DESCRIPTION
—
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2014 Maxim Integrated Products, Inc. │ 16