CREE XMLBWT-00-0000

CLD-DS61 Rev 0
Product family data sheet
Cree® XLamp® XM-L2 LEDs
Product Description
FEATURES
Table of Contents
The XLamp XM-L2 LED builds on
• Available in white, 80‑CRI white,
Flux Characteristics..................... 2
the unprecedented performance of
the original XM-L, increasing lumen
output up to 20% while providing
• ANSI‑compatible chromaticity
bins
Characteristics........................... 3
Relative Spectral Power
Distribution............................... 3
a single die LED point source for
• Binned at 85 °C
Relative Flux vs. Junction
precise optical control. The XM-L2
• Maximum drive current:
Temperature.............................. 4
LED shares the same mechanical
and optical footprint as the original
XM-L, providing a seamless upgrade
path and shortened design cycle.
XLamp XM-L2 LEDs are the ideal
choice
for
where
high
lighting
light
applications
output
and
maximum efficacy are required,
WWW.CREE.COM/XLAMP
85‑CRI white and 90‑CRI white
3000 mA
• Low thermal resistance:
2.5 °C/W
Electrical Characteristics.............. 4
Thermal Design.......................... 5
Relative Flux vs. Current ............ 5
• Wide viewing angle: 125°
Relative Chromaticity vs. Current.. 6
• Unlimited floor life at
Relative Chromaticity vs.
≤ 30 ºC/85% RH
• Reflow solderable - JEDEC
J‑STD‑020C
• Electrically neutral thermal path
Temperature.............................. 6
Typical Spatial Distribution........... 7
Reflow Soldering Characteristics... 8
Notes........................................ 9
such as LED light bulbs, outdoor
Mechanical Dimensions..............10
lighting, portable lighting, indoor
Tape and Reel...........................11
lighting and solar-powered lighting.
Packaging.................................12
Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®,
Copyright © 2010 Cree, Inc.
All rights reserved. The information in this document is subject to change without notice.
the Cree logo and XLamp® are registered trademarks of Cree, Inc.
Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
www.cree.com/xlamp
xlamp xm-l2 leds
Flux Characteristics (TJ = 85 °C)
The following table provides several base order codes for XLamp XM-L2 LEDs. It is important to note that the base order
codes listed here are a subset of the total available order codes for the product family. For more order codes, as well
as a complete description of the order-code nomenclature, please consult the XLamp XM-L Family Binning and Labeling
document.
CCT Range
Color
Min.
Cool White
5000 K
Max.
8300 K
Neutral White
3700 K
5000 K
Warm White
2600 K
3700 K
80-CRI White
2600 K
4300 K
85-CRI White
90-CRI White
2600 K
2600 K
3200 K
3200 K
Base Order Codes
Min. Luminous Flux (lm)
@ 700 mA
Calculated Minimum
Luminous Flux (lm)
@ 85 °C**
Order Code
Group
Flux (lm)
@ 85 °C
Flux (lm)
@ 25 °C*
1000 mA
1500 mA
2000 mA
T5
260
296
357
502
631
XMLBWT-00-0000-0000T5051
T6
280
318
385
541
679
XMLBWT-00-0000-0000T6051
U2
300
341
412
580
728
XMLBWT-00-0000-0000U2051
T4
240
273
330
464
582
XMLBWT-00-0000-000LT40E4
T5
260
296
357
502
631
XMLBWT-00-0000-000LT50E4
T2
200
227
275
386
485
XMLBWT-00-0000-000LT20E7
T3
220
250
302
425
534
XMLBWT-00-0000-000LT30E7
T2
200
227
275
386
485
XMLBWT-00-0000-000HT20E7
T3
220
250
302
425
534
XMLBWT-00-0000-000HT30E7
S4
164
186
225
317
398
XMLBWT-00-0000-000PS40E7
S5
172
196
236
332
417
XMLBWT-00-0000-000PS50E7
S6
182
207
250
352
442
XMLBWT-00-0000-000PS60E7
S4
164
186
225
317
398
XMLBWT-00-0000-000US40E7
S5
172
196
236
332
417
XMLBWT-00-0000-000US50E7
S6
182
207
250
352
442
XMLBWT-00-0000-000US60E7
Notes:
•
Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy)
measurements and ±2 on CRI measurements.
•
Typical CRI for Cool White (5000 K – 8300 K CCT) is 65.
•
Typical CRI for Neutral White (3700 K – 5000 K CCT) is 75.
•
Typical CRI for Warm White (2600 K – 3700 K CCT) is 80.
•
Minimum CRI for 80-CRI White is 80.
•
Minimum CRI for 85-CRI White is 85.
•
Minimum CRI for 90-CRI White is 90.
*
Flux values @ 25 °C are calculated and are for reference only.
** Calculated flux values at 1000 mA, 1500 mA and 2000 mA are for reference only.
®
Copyright © 2012
, the
2010 Cree,
Cree, Inc.
Inc. All
All rights
rights reserved.
reserved.The
Theinformation
informationininthis
thisdocument
documentisissubject
subjecttotochange
changewithout
withoutnotice.
notice.Cree
Cree,
the Cree
Creelogo
logoand
andXLamp
XLamp® are registered trademarks
of Cree, Inc.
2
xlamp xm-l2 leds
Characteristics
Characteristics
Unit
Thermal resistance, junction to solder point
°C/W
Viewing angle (FWHM)
Temperature coefficient of voltage
Minimum
Typical
Maximum
2.5
degrees
125
mV/°C
-1.6
ESD classification (HBM per Mil-Std-883D)
Class 2
DC forward current
mA
3000
Reverse voltage
V
-5
Forward voltage (@ 700 mA, 85 °C)
V
2.85
Forward voltage (@ 1500 mA, 85 °C)
V
3.05
Forward voltage (@ 3000 mA, 85 °C)
V
3.3
LED junction temperature
°C
3.5
150
Relative Spectral Power
Relative Spectral Power Distribution
Relative Radiant Power (%)
100
80
60
5000K - 8300K CCT
3700K - 5000K CCT
2600K - 3700K CCT
40
20
0
380
430
480
530
580
630
680
730
780
Wavelength (nm)
®
Copyright © 2012
, the
2010 Cree,
Cree, Inc.
Inc. All
All rights
rights reserved.
reserved.The
Theinformation
informationininthis
thisdocument
documentisissubject
subjecttotochange
changewithout
withoutnotice.
notice.Cree
Cree,
the Cree
Creelogo
logoand
andXLamp
XLamp® are registered trademarks
of Cree, Inc.
3
xlamp xm-l2 leds
Relative Flux Output vs. Junction Temperature
Relative Flux vs. Junction Temperature (IF = 700 mA)
Relative Luminous Flux (%)
120
100
80
60
40
20
0
25
50
75
100
125
150
Junction Temperature (ºC)
Electrical Characteristics (Tj = 85°C)
Electrical Characteristics (TJ = 85 °C)
3000
2800
2600
Forward Current (mA)
2400
2200
2000
1800
1600
1400
1200
1000
800
600
400
200
0
2.60
2.80
3.00
3.20
3.40
Forward Voltage (V)
®
Copyright © 2012
, the
2010 Cree,
Cree, Inc.
Inc. All
All rights
rights reserved.
reserved.The
Theinformation
informationininthis
thisdocument
documentisissubject
subjecttotochange
changewithout
withoutnotice.
notice.Cree
Cree,
the Cree
Creelogo
logoand
andXLamp
XLamp® are registered trademarks
of Cree, Inc.
4
xlamp xm-l2 leds
Thermal Design
The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is
Thermal
Design
crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to
Cool White
ambient in order to optimize lamp life and optical characteristics.
3500
Maximum Current (mA)
3000
2500
2000
1500
Rj-a = 4°C/W
1000
Rj-a = 7°C/W
Rj-a = 10°C/W
500
Rj-a = 15°C/W
0
0
25
50
75
100
125
150
Ambient Temperature (ºC)
Relative Intensity vs. Current (Tj = 85°C)
Relative Flux vs. Current (TJ = 85 °C)
Relative Luminous Flux (%)
350
300
250
200
150
100
50
0
0
200
400
600
800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000
Forward Current (mA)
®
Copyright © 2012
, the
2010 Cree,
Cree, Inc.
Inc. All
All rights
rights reserved.
reserved.The
Theinformation
informationininthis
thisdocument
documentisissubject
subjecttotochange
changewithout
withoutnotice.
notice.Cree
Cree,
the Cree
Creelogo
logoand
andXLamp
XLamp® are registered trademarks
of Cree, Inc.
5
xlamp xm-l2 leds
Relative Chromaticity Vs. Current, WW
Relative Chromaticity vs. Current (Warm White)
0.012
0.008
0.004
ΔCCx
0.000
ΔCCy
-0.004
-0.008
-0.012
0
500
1000
1500
2000
2500
3000
Current (mA)
Relative Chromaticity Vs. Temperature WW
Relative Chromaticity vs. Temperature (Warm White)
0.012
0.008
0.004
ΔCCx
0.000
ΔCCy
-0.004
-0.008
-0.012
25
50
75
100
125
150
Tsp (°C)
®
Copyright © 2012
, the
2010 Cree,
Cree, Inc.
Inc. All
All rights
rights reserved.
reserved.The
Theinformation
informationininthis
thisdocument
documentisissubject
subjecttotochange
changewithout
withoutnotice.
notice.Cree
Cree,
the Cree
Creelogo
logoand
andXLamp
XLamp® are registered trademarks
of Cree, Inc.
6
xlamp xm-l2 leds
Typical Spatial Radiation Pattern
Typical Spatial Distribution
Relative Luminous Intensity (%)
100
80
60
40
20
0
-90
-70
-50
-30
-10
10
30
50
70
90
Angle (º)
®
Copyright © 2012
, the
2010 Cree,
Cree, Inc.
Inc. All
All rights
rights reserved.
reserved.The
Theinformation
informationininthis
thisdocument
documentisissubject
subjecttotochange
changewithout
withoutnotice.
notice.Cree
Cree,
the Cree
Creelogo
logoand
andXLamp
XLamp® are registered trademarks
of Cree, Inc.
7
xlamp xm-l2 leds
Reflow Soldering Characteristics
In testing, Cree has found XLamp XM-L2 LEDs to be compatible with JEDEC J‑STD‑020C, using the parameters listed
below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the
manufacturer of solder paste used.
Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment.
Profile Feature
Lead-Based Solder
Lead-Free Solder
3 °C/second max.
3 °C/second max.
Preheat: Temperature Min (Tsmin)
100 °C
150 °C
Preheat: Temperature Max (Tsmax)
150 °C
200 °C
60-120 seconds
60-180 seconds
183 °C
217 °C
60-150 seconds
60-150 seconds
215 °C
260 °C
10-30 seconds
20-40 seconds
6 °C/second max.
6 °C/second max.
6 minutes max.
8 minutes max.
Average Ramp-Up Rate (Tsmax to Tp)
Preheat: Time (tsmin to tsmax)
Time Maintained Above: Temperature (TL)
Time Maintained Above: Time (tL)
Peak/Classification Temperature (Tp)
Time Within 5 °C of Actual Peak Temperature (tp)
Ramp-Down Rate
Time 25 °C to Peak Temperature
Note: All temperatures refer to the topside of the package, measured on the package body surface.
®
Copyright © 2012
, the
2010 Cree,
Cree, Inc.
Inc. All
All rights
rights reserved.
reserved.The
Theinformation
informationininthis
thisdocument
documentisissubject
subjecttotochange
changewithout
withoutnotice.
notice.Cree
Cree,
the Cree
Creelogo
logoand
andXLamp
XLamp® are registered trademarks
of Cree, Inc.
8
xlamp xm-l2 leds
Notes
Lumen Maintenance Projections
Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED
lumen maintenance. For information on the specific LM‑80 data sets available for this LED, refer to the public LM-80
results document at www.cree.com/xlamp_app_notes/LM80_results.
Please read the XLamp Long-Term Lumen Maintenance application note at www.cree.com/xlamp_app_notes/lumen_
maintenance for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal
Management application note at www.cree.com/xlamp_app_notes/thermal_management for details on how thermal
design, ambient temperature, and drive current affect the LED junction temperature.
Moisture Sensitivity
In testing, Cree has found XLamp XM-L2 LEDs to have unlimited floor life in conditions ≤30 ºC/85% relative humidity
(RH). Moisture testing included a 168‑hour soak at 85 ºC/85% RH followed by 3 reflow cycles, with visual and electrical
inspections at each stage.
Cree recommends keeping XLamp LEDs in their sealed moisture-barrier packaging until immediately prior to use. Cree
also recommends returning any unused LEDs to the resealable moisture‑barrier bag and closing the bag immediately
after use.
Vision Advisory Claim
WARNING: Do not look at exposed lamp in operation. Eye injury can result. See the LED Eye Safety application note at
www.cree.com/xlamp_app_notes/led_eye_safety.
®
Copyright © 2012
, the
2010 Cree,
Cree, Inc.
Inc. All
All rights
rights reserved.
reserved.The
Theinformation
informationininthis
thisdocument
documentisissubject
subjecttotochange
changewithout
withoutnotice.
notice.Cree
Cree,
the Cree
Creelogo
logoand
andXLamp
XLamp® are registered trademarks
of Cree, Inc.
9
4.78
xlamp xm-l2 leds
C
R2.26
Mechanical Dimensions
All measurements are ±.13 mm unless otherwise indicated.
4.7
3.9
.600
6
5
NOTICE
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
CONTAINED WITHIN ARE THE PROPRIETARY AND
6
5 OF CREE, INC. THIS PLOT
CONFIDENTIAL INFORMATION
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
NOTICE
UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT
4.7
.400
CREE CONFIDENTIAL.
THIS PLOT AND THE OF
INFORMATION
CREE INC.
CONTAINED WITHIN ARE THE PROPRIETARY AND
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT
OF CREE INC.
4
4
2
REV
3
2
DESCRIPTION
1
B
ADDED DOME RA
REVISONS
D
REV
DESCRIPTION
BY
DATE
A
INITIAL RELEASE
DC
11/14/12
3.78
3.78
3.02
3.02
5.000
5.00
.400
3
B
Anode
.50
.73
.50
0.73
APP'D
2.78
2.78
.400
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
.XX ±
.25
.XXX ±
.125
X°
±
.5 °
RECOMMENDED STENCIL PATTERN
SHADED AREA IS OPEN
5.000
THIRD ANGLE
PROJECTION
5.00
FOR SHEET METAL PARTS ONLY
.X
±
1.5
.XX ±
.75
.XXX ±
.25
X°
±
.5 °
Anode
D. CRONIN
CHECK
4600 Silicon Drive
Durham, N.C 27703
11/14/12
DATE
--
Phone (919) 313-5300
--
Fax (919) 313-5558
--
--
MATERIAL
--
TITLE
OUTLINE DRAWING, 5050 XMLB
SIZE
--
SCALE
2610-00032
SHEET
16.000
2
4.78
4.78
REV.
DRAWING NO.
C
FINAL PROTECTIVE FINISH
3
A
DATE
APPROVED
SURFACE FINISH: 1.6
4
DATE
DRAWN BY
A
OF
1 /1
1
C
R2.190
R2.26
Top View
Bottom View
Side View
4.7
3.9
4.8
3.8
4.8
4.7
3.9
.500
3.8
.500
.600
.600
B
4.8
.500
.500
4.7
.500
.400
2.782
2.782
A
.400
.400
4.7
.400
4.8
.500
.400
.400
.400
.400
Recommended
PCB
Solder
RECOMMENDED PCB
SOLDER
PAD
RECOMMENDED STENCIL PATTERN
SHADED AREA IS OPEN
Pad
Recommended Stencil Pattern
UNLESS OTHERWISE SPECIFIED
RECOMMENDED STENCIL PATTERN
D. CRONIN
(Shaded Area
Is Open)
DIMENSIONS
ARE IN
DRAWN BY
SHADED AREA IS OPEN
RECOMMENDED PCB SOLDER PAD
THIRD ANGLE PROJECTION
6
5
4
MILLIMETERS AND AFTER
FINISH.
THIRD
ANGLECHECK
PROJECTION
-TOLERANCE UNLESS SPECIFIED:
.XX ±
.25
APPROVED
.XXX ±
.125
-X°
±
.5 °
FOR SHEET METAL PARTS ONLY
.X
±
1.5
.XX ±
.75
.XXX ±
.25
X°
±
.5 °
SURFACE FINISH: 1.6
6
5
4
3
MATERIAL
3
--
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
DATE
.XX ±
.25
.XXX ±
.125
11/14/12
X°
±
.5 °
DATE
FOR SHEET METAL PARTS ONLY
-.X
±
1.5
.XX ±
.75
TITLE
-.XXX ±
.25
X°
±
.5 °
D. CRONIN
08/1/11
DATE
-APPROVED
-MATERIAL
-DATE
4600 Silicon Drive
-- 27703
Durham, N.C
O
Phone (919) 313-530
Fax (919) 313-5558
--
DATE
OUTLINE DRAWING, 5050 XM
FINAL PROTECTIVE FINISH
--
SURFACE FINISH: 1.6
SIZE
FINAL PROTECTIVE FINISH
--
DATE
DRAWN BY
CHECK
SCALE
C
DRAWING NO.
2
2610-00032
SHEET
16.000
2
1
®
Copyright © 2012
, the
2010 Cree,
Cree, Inc.
Inc. All
All rights
rights reserved.
reserved.The
Theinformation
informationininthis
thisdocument
documentisissubject
subjecttotochange
changewithout
withoutnotice.
notice.Cree
Cree,
the Cree
Creelogo
logoand
andXLamp
XLamp® are registered trademarks
of Cree, Inc.
10
OF
6
5
4
3
2.00[.079]
4.00[.157]
1
2
REVISIONS
NOTICE
EE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
NTAINED WITHIN ARE THE PROPRIETARY AND
NFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
Y NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
AUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
CREE INC.
DESCRIPTION
REV
BY
DATE
APP'D
POCKET SIZE
+.10
+.0039
.0591
-.00
-.0000 [ ]
Do1.50
P2
1.75[.069]
E1
Po
Ao -
5.40mm [.213"]
Bo -
5.40mm [.213"]
Ko -
3.35mm [.132"]
xlamp xm-l2 leds
D
Tape and Reel
3.0°
5.40[.213]
Bo
3
12.00[.472]
All Cree carrier tapes conform to EIA-481D,
Automated
Component Handling
Systems
Standard.
6
5
4
3
5.50[.217]F
6
5
4
NOMINAL
OF CREE INC.
D
D
2.00[.079]
2.00[.079]
P2
1.50[.059]
4.00[.157]
D1
4.00[.157]
Po
8.00[.315]
P
REV
12.30 [.484]
MAX
W
10.25
[.404]
E2
REV
+.10
+.0039
Do1.50
.0591
+.0039
-.00 +.10 .0591
-.0000
[]
Do1.50
-.00
-.0000 [ ]
P2
6
5
C
NOTICE
NTIAL. THIS PLOT AND THE INFORMATION
THIN ARE THE PROPRIETARY AND
INFORMATION OF CREE, INC. THIS PLOT
OPIED, REPRODUCED OR DISCLOSED TO ANY
D PERSON WITHOUTTHE WRITTEN CONSENT
5.40[.213]
4
3.0°
A
B
BY
1
DATE
APP'D
DATE
APP'D
D
Ao
B
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
.XX ±
.01
.XXX ±
.005
X°
±
.5 °
FOR SHEET METAL PARTS ONLY
.X
±
.06
.XX ±
.03
.XXX ±
.010
X°
±
.5 °
1
C
BY
DATE
DDS
11/8/10
DC
2/26/12
5
4
8
6
BS
A
Loaded Pockets
(1000 Lamps)
1.50[.059]
Phone (919) 313-5300
Fax (919) 313-5558
D1 1.50[.059]
D1
8.00[.315]
DATE
8.00[.315]
P TITLE
P
APPROVED
SIZE
A
FINAL PROTECTIVE FINISH
User Feed Direction
REV.
DRAWING NO.
2402-00011
7.0°
SCALE
DRAWING SCALE
2
SHEET
7.0°
1
A
OF
4
1.75
3.35[.132]
3.35[.132]
3
Ko
Ko
START
12
.36[.014] D
T .36[.014]
T
A
XM 5050 CARRIER TAPE
MATERIAL
5.40[.213]
5.40[.213]
Ao
ANODE SIDE
4600 Silicon Drive
Durham, N.C 27703
4/23/10
DATE
CATHODE SIDE
4
5
Trailer
160mm (min) of
empty pockets
sealed with tape
(15 pockets min.)
D. CRONIN
CHECK
3
A
B
3.35
2
1
2400-00009
CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275
CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275
INDEX
QTY
ITEM
1
1
2400-00009-CORE
DRAWN BY
COMMENTS
DATE
UNLESS OTHERWISE SPECIFIED
DATE
4/23/10
2 D. CRONIN
2DRAWN BY2400-00009-REEL
UNLESS ARE
OTHERWISE
SPECIFIED
DIMENSIONS
IN INCHES
D. CRONIN
4/23/10
DATE
DIMENSIONS
ARE IN INCHESCHECK
AND
AFTER FINISH.
CHECK
DATE
AND
AFTERSPECIFIED:
FINISH.
TOLERANCE
UNLESS
TOLERANCE
.XX ± UNLESS
.01 SPECIFIED:
APPROVED
DATE
TITLE
.XX
±
.01
.XXX ±
.005
APPROVED
DATE
TITLE
X°
±.XXX .5± ° .005
THIRD ANGLE PROJECTION
MATERIAL
X° PARTS
±
.5
°
FOR SHEET METAL
ONLY
Leader
THIRD ANGLE PROJECTION
MATERIAL
FOR.XSHEET
± METAL
.06 PARTS ONLY
DRAWING NO.
400mm (min.) of
SIZE
.XX .X
±
±.03 .06
DRAWING NO.
SIZE
FINAL PROTECTIVE FINISH
±
.03
empty pockets with
.XXX .XX
±
.010
FINAL PROTECTIVE FINISH
X°
±.XXX .5± ° .010
at least 100mm
SCALE
X°
±
.5 °
SURFACE FINISH: 63
SCALE
sealed by tape
DRAWING
SCALE
SURFACE FINISH: 63
DRAWING SCALE
Ao
C
4600 Silicon Drive
Durham,
N.C
27703
4600
Silicon
Drive
Durham,
N.C 27703
Phone (919)
313-5300
Phone
(919) 313-5300
Fax (919)
313-5558
Fax (919) 313-5558
XMXM
5050
CARRIER
TAPE
5050
CARRIER
TAPE
2402-00011
A
2402-00011 A
6
(405 empty pockets min.)
4
5
3
4
2
3
A
REV.
A
6
SHEET
OF
SHEET
1
2
1OF / 1
1
D
REV.
A
1 /1
12.4
+.2
.0
MEASURED AT HUB
C
C
330
+.25
-.75
16.4
+0.2
.0
MEASURED AT HUB
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
.XX ±
.25
.XXX ±
.125
X°
±
.5 °
FOR SHEET METAL PARTS ONLY
.X
±
1.5
.XX ±
.75
.XXX ±
.25
X°
±
.5 °
SURFACE FINISH:
5
4
1.6
3
1.9±.4
DATE
DRAWN BY
D. CRONIN
CHECK
21 ±.4
4600 Silicon Drive
Durham, N.C 27703
06/08/10
DATE
--
Phone (919) 313-5300
--
Fax (919) 313-5558
A
DATE
APPROVED
--
--
MATERIAL
TITLE
13.1 ±.2
--
SIZE
FINAL PROTECTIVE FINISH
--
SCALE
XM LOADING SPEC
REV.
DRAWING NO.
C
2402-00012
SHEET
3.000
2
B
OF
B
1 /1
1
12.4
+1.0
-.5
MEASURED AT EDGE
60°
60°
REVISONS
REV
DESCRIPTION
BY
DATE
APP'D
®
Copyright © 2012
, the
2010 Cree,
Cree, Inc.
Inc. All
All rights
rights reserved.
reserved.The
Theinformation
informationininthis
thisdocument
documentisissubject
subjecttotochange
changewithout
withoutnotice.
notice.Cree
Cree,
the Cree
Creelogo
logoand
andXLamp
XLamp® are registered trademarks
of Cree, Inc.
UNLESS OTHERWISE SPECIFIED
DRAWN BY
A
THIRD ANGLE PROJECTION
B
1 /1
B
B
C
APP'D
DATE
DRAWN BY
63
NOTICE
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
CONTANED WITHIN ARE THE PROPRIETARY AND
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
OF CREE INC.
6
D
CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275
SURFACE FINISH:
D
2
BY
5.40[.213]
5.40[.213]
Bo
Bo
3.0°
12.00[.472]
12.00[.472]
NOMINAL
NOMINAL
REVISONS
[.484]
10.25 12.30DESCRIPTION
12.30
[.484]
MAX
Loaded pocket
count was 750
[.404]10.25
MAX
[.404]
WANODE
E2
MADE CATHODE AND
W NOTE LARGER
E2
REV
3.35[.132]
Ko
B
END
5.50[.217]F
5.50[.217]F
3
C
THIRD ANGLE PROJECTION
6
REVISIONS
REVISIONS
DESCRIPTION
DESCRIPTION
BoBo
- - 5.40mm
[.213"]
5.40mm
[.213"]
KoKo
- - 3.35mm
[.132"]
3.35mm
[.132"]
1.75[.069]
E1 1.75[.069]
E1
.36[.014]
T
Po
1
2
POCKET
SIZE
POCKET
SIZE in mm.
All dimensions
AoAo
- - 5.40mm
[.213"]
5.40mm [.213"]
B
7.0°
2
C
NOTICE
CREE CONFIDENTIAL. THIS PLOT
AND THE INFORMATION
NOTICE
CONTAINED
WITHIN ARE THETHIS
PROPRIETARY
ANDINFORMATION
CREE CONFIDENTIAL.
PLOT AND THE
CONFIDENTIAL
INFORMATION
CREE,
INC. THIS PLOT
CONTAINED
WITHIN AREOF
THE
PROPRIETARY
AND
MAY NOT
BE COPIED, INFORMATION
REPRODUCEDOF
ORCREE,
DISCLOSED
TO PLOT
ANY
CONFIDENTIAL
INC. THIS
UNAUTHORIZED
PERSON
WITHOUT
THE WRITTEN
CONSENT
MAY NOT BE COPIED, REPRODUCED
OR DISCLOSED
TO ANY
OF CREE
INC.
UNAUTHORIZED
PERSON WITHOUT THE WRITTEN CONSENT
DIMENSIONS ARE IN INCHES
AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
.XX ±
.01
.XXX ±
.005
X°
±
.5 °
FOR SHEET METAL PARTS ONLY
D. CRONIN
CHECK
DATE
4600 Silicon Drive
Durham, N.C 27703
09/29/09
DATE
-APPROVED
-MATERIAL
11
Phone (919) 313-5300
--
Fax (919) 313-5558
DATE
--
TITLE
REEL, 13" X 12MM, 3 PIECE SNAP
A
A
xlamp xm-l2 leds
Humidity Indicator
Card (inside bag)
Packaging
Dessicant
(inside bag)
Unpackaged Reel
Label with Cree Bin
Code, Qty, Reel ID
Packaged Reel
Label with Cree Bin
Code, Qty, Lot #
Vacuum-Sealed
Moisture Barrier Bag
Label with Cree Order Code,
Qty, Reel ID, PO #
Label with Cree Bin
Code, Qty, Reel ID
Label with Custo
Code, Qty, Reel I
Boxed Reel
Label with Cree Order Code,
Qty, Reel ID, PO #
Patent Label
Label with Cree Bin
Code, Qty, Reel ID
Patent Label
®
Copyright © 2012
, the
2010 Cree,
Cree, Inc.
Inc. All
All rights
rights reserved.
reserved.The
Theinformation
informationininthis
thisdocument
documentisissubject
subjecttotochange
changewithout
withoutnotice.
notice.Cree
Cree,
the Cree
Creelogo
logoand
andXLamp
XLamp® are registered trademarks
of Cree, Inc.
12