® ® Cree XLamp XP-E2 LEDs Product Description FEATURES Table of Contents The XLamp XP-E2 LED builds on the • Available in white, outdoor white, Flux Characteristics..................... 2 unprecedented performance of the 80-CRI, 85-CRI and 90-CRI white Characteristics........................... 3 original XP-E by increasing lumen output up to 20% while providing • ANSI-compatible chromaticity bins Relative Spectral Power Distribution............................... 3 a single die LED point source for • Binned @ 85 °C Relative Flux vs. Junction precise optical control. The XP- • Maximum drive current: 1 A Temperature.............................. 4 E2 LED shares the same footprint • Low thermal resistance: 9 °C/W Electrical Characteristics.............. 4 as the original XP-E, providing a •Wide viewing angle: 110° Thermal Design.......................... 5 seamless upgrade path to more • Unlimited floor life at Relative Flux vs. Current............. 5 lumens and/or greater efficiency while shortening the design cycle for existing XP customers. ≤ 30 °C/85% RH • Reflow solderable - JEDEC J-STD020C compatible • Electrically neutral thermal path Relative Chromaticity vs. Current and Temperature - Warm White.... 6 Typical Spatial Distribution........... 7 Reflow Soldering Characteristics... 8 XLamp XP-E2 LEDs are the ideal Notes........................................ 9 choice for Mechanical Dimensions..............10 where high lighting light applications output and Tape and Reel...........................11 maximum efficacy are required, Packaging.................................12 such as LED retrofit lamps, outdoor lighting, portable lighting, or indoor www. cree.com/Xlamp directional lighting. Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 CLD-DS56 Rev 0 Product family data sheet xlamp xp-e2 leds Flux Characteristics (TJ = 85 °C) The following table provides several base order codes for XLamp XP-E2 LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XLamp XP Family Binning and Labeling document. CCT Range Color Min. Cool White Outdoor White Neutral White 80-CRI White Warm White 85-CRI White 90-CRI White 5000 K 4000 K 3700 K 2600 K 2600 K 2600 K 2600 K Max. 10,000 K 5300 K 5300 K 4300 K 3700 K 3200 K 3200 K Base Order Codes Min. Luminous Flux (lm) @ 350 mA Calculated Minimum Luminous Flux (lm)** @ 85 °C Order Code Group Flux (lm) @ 85 °C Flux (lm) @ 25 °C* 700 mA 1.0 A Q4 100 116 171 218 XPEBWT-L1-0000-00C51 Q5 107 124 183 233 XPEBWT-L1-0000-00D51 R2 114 132 195 249 XPEBWT-L1-0000-00E51 R3 122 142 209 266 XPEBWT-L1-0000-00F51 Q4 100 116 171 218 XPEBWT-01-0000-00CC2 Q5 107 124 183 233 XPEBWT-01-0000-00DC2 R2 114 132 195 249 XPEBWT-01-0000-00EC2 R3 122 142 209 266 XPEBWT-01-0000-00FC2 Q4 100 116 171 218 XPEBWT-L1-0000-00CE4 Q5 107 124 183 233 XPEBWT-L1-0000-00DE4 R2 114 132 195 249 XPEBWT-L1-0000-00EE4 Q2 87.4 101 150 191 XPEBWT-H1-0000-00AE7 Q3 93.9 109 161 205 XPEBWT-H1-0000-00BE7 Q2 87.4 101 150 191 XPEBWT-L1-0000-00AE7 Q3 93.9 109 161 205 XPEBWT-L1-0000-00BE7 Q4 100 116 171 218 XPEBWT-L1-0000-00CE7 P2 67.2 78.0 115 147 XPEBWT-P1-0000-007E7 P3 73.9 85.7 127 161 XPEBWT-P1-0000-008E7 P4 80.6 93.5 138 176 XPEBWT-P1-0000-009E7 Q2 87.4 101 150 191 XPEBWT-P1-0000-00AE7 P2 67.2 78.0 115 147 XPEBWT-U1-0000-007E7 P3 73.9 85.7 127 161 XPEBWT-U1-0000-008E7 P4 80.6 93.5 138 176 XPEBWT-U1-0000-009E7 Notes: • Cree maintains a tolerance of ± 7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements. • Typical CRI for Cool White (5000 K – 10,000 K CCT) is 70. • Typical CRI for Neutral White (3700 K – 5300 K CCT) is 75. • Typical CRI for Outdoor White (4000 K - 5300 K CCT) is 70. • Typical CRI for Warm White (2600 K – 3700 K CCT) is 80. • Minimum CRI for 80-CRI White is 80. • Minimum CRI for 85-CRI White is 85. • Minimum CRI for 90-CRI White is 90. * Flux values @ 25 °C are calculated and for reference only. ** Calculated flux values are for reference only. Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 2 xlamp xp-e2 leds Characteristics Characteristics Unit Thermal resistance, junction to solder point Viewing angle (FWHM) Minimum Typical °C/W 9 degrees 110 mV/°C -2.3 Temperature coefficient of voltage ESD classification (HBM per Mil-Std-883D) Maximum Class 2 DC forward current mA Reverse voltage V Forward voltage (@ 350 mA, 85 °C) V 350 -5 2.9 Forward voltage (@ 700 mA, 85 °C) 3.05 Forward voltage (@ 1000 mA, 85 °C) 3.15 LED junction temperature 1000 °C 3.75 150 Relative Spectral Power Distribution Relative Spectral Power Relative Radiant Power 100% 90% 80% 70% 60% Cool White 50% Warm White 40% 30% 20% 10% 0% 380 430 480 530 580 630 680 730 780 Wavelength (nm) Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 3 xlamp xp-e2 leds Relative Flux vs. Junction Temperature (IF = 350 mA) Relative Flux Output vs. Junction Temperature 120% Relative Luminous Flux 100% 80% 60% 40% 20% 0% 25 50 75 100 125 150 Junction Temperature (ºC) Electrical Characteristics (TJ = 85 °C) Electrical Characteristics (Tj = 25ºC) 1000 900 Forward Current (mA) 800 700 600 500 400 300 200 100 0 2.7 2.8 2.9 3.0 3.1 3.2 Forward Voltage (V) Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 4 xlamp xp-e2 leds Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. 1200 Maximum Current (mA) 1000 800 600 Rj-a Rj-a Rj-a Rj-a 400 = = = = 10°C/W 15°C/W 20°C/W 25°C/W 200 0 0 20 40 60 80 100 120 140 Ambient Temperature (ºC) Relative Flux vs. Current (TJ = 85 °C) Relative Intensity vs. Current (Tj = 85ºC) Relative Luminous Flux 250% 200% 150% 100% 50% 0% 0 100 200 300 400 500 600 700 800 900 1000 Forward Current (mA) Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 5 xlamp xp-e2 leds Relative Chromaticity Vs. Current, WW Relative Chromaticity vs. Current and Temperature - Warm White* 0.020 T = 85 °C J 0.015 0.010 0.005 ΔCCx 0.000 ΔCCy -0.005 -0.010 -0.015 -0.020 0 100 200 300 400 500 600 700 800 900 1000 Current (mA) Relative Chromaticity Vs. Temperature WW 0.020 I = 350 mA F 0.015 0.010 0.005 ΔCCx 0.000 ΔCCy -0.005 -0.010 -0.015 -0.020 0 20 40 60 80 100 120 140 160 Tsp (°C) * Warm White XLamp XP-E2 LEDs have a typical CRI of 80. Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 6 xlamp xp-e2 leds Typical Spatial Radiation Pattern Typical Spatial Distribution Relative Luminous Intensity 100% 80% 60% 40% 20% 0% -100 -80 -60 -40 -20 0 20 40 60 80 100 Angle (°) Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 7 xlamp xp-e2 leds Reflow Soldering Characteristics In testing, Cree has found XLamp XP-E2 LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. Profile Feature Average Ramp-Up Rate (Tsmax to Tp) Lead-Based Solder Lead-Free Solder 3 °C/second max. 3 °C/second max. Preheat: Temperature Min (Tsmin) 100 °C 150 °C Preheat: Temperature Max (Tsmax) 150 °C 200 °C 60-120 seconds 60-180 seconds 183 °C 217 °C 60-150 seconds 60-150 seconds 215 °C 260 °C 10-30 seconds 20-40 seconds 6 °C/second max. 6 °C/second max 6 minutes max. 8 minutes max. Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) Time Within 5 °C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25 °C to Peak Temperature Note: All temperatures refer to topside of the package, measured on the package body surface. Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 8 xlamp xp-e2 leds Notes Lumen Maintenance Projections Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document at www.cree.com/xlamp_app_notes/LM80_results. Please read the XLamp Long-Term Lumen Maintenance application note at www.cree.com/xlamp_app_notes/XRE_ lumen_maintenance for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note at www.cree.com/xlamp_app_notes/thermal_management for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture Sensitivity In testing, Cree has found XLamp XP-E2 LEDs to have unlimited floor life in conditions ≤ 30 ºC/85% relative humidity (RH). Moisture testing included a 168-hour soak at 85 ºC/85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. Cree recommends keeping XLamp LEDs in their sealed moisture-barrier packaging until immediately prior to use. Cree also recommends returning any unused LEDS to the resealable moisture-barrier bag and closing the bag immediately after use. RoHS Compliance The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006. Vision Advisory Claim WARNING: Do not look at exposed lamp in operation. Eye injury can result. See LED Eye Safety at www.cree.com/ xlamp_app_notes/led_eye_safety. Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 9 3.30 C xlamp xp-e2 leds .65 1.30 Mechanical Dimensions 6 5 3 Anode 6 5 D 6 .60 5 4 5 4 3 4 3 3 3.45 REV REV .83 3.20 1.60 2 B 2 2 REVISONS REVISONS REVISO TICE NOTICE OT THE INFORMATION HISAND PLOT AND THE INFORMATION TIAL. THIS PLOT AND THE INFORMATION 1.20 PROPRIETARY AND EINTHE PROPRIETARY AND AND ARE THE PROPRIETARY OF CREE, INC. THIS PLOT ATION OF CREE, INC. THIS FORMATION OF CREE, INC.PLOT THIS PLOT DUCED OR DISCLOSED ANYTO ANY EPRODUCED OR DISCLOSED IED, REPRODUCED OR TO DISCLOSED TO ANY HOUT THEWITHOUT WRITTEN CONSENT N WITHOUT THE WRITTEN CONSENT PERSON THE WRITTEN CONSENT REV DESCRIPTION DESCRIPTION DESCRIPTION 3.30 3.30 3.30 2.30 2.30 2.30 .50 .50 .50 3.45 3.45 3.45 3.45 .83 .83 .83 .40 3.20 C NDED STENCIL PATTERN AREA OPENING) 3.45IS 3.45 3.45 THIRD ANGLE PROJECTION UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH: 1.6 3 R1.53 DATE DRAWN BY D. CRONIN 4600 Silicon Drive Durham, N.C 27703 07/19/12 CHECK DATE APPROVED DATE .65 Phone (919) 313-5300 Fax (919) 313-5558 A TITLE 3.30 3.30 3.30 OUTLINE DRAWING XPE G2 MATERIAL SIZE C FINAL PROTECTIVE FINISH SCALE R1.53 R1.53R1.53 2 REV. DRAWING NO. 2610-00029 SHEET 22.000 A OF 1 /1 1 Anode .65 .65 .65 1.30 1.30 1.30 1.15 .60 .65 B 1.20 .50 1.15 1.15 1.15 65 0 4 All measurements are ±.13 mm unless otherwise indicated. NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC. .60 .50 3.30 .60 .65 .65 1.65 1.20 1.20 1.20 .50 .50 .60 .40 .50 3.20 .60 .60 A .60 .60 .40 1.60 .40 .40 .50 3.30 3.30 3.30 1.30 3.20 3.30 3.20 3.20 3.20 RECOMMENDED STENCIL PATTERN 1.60 1.60 1.60 (HATCHED AREA IS OPENING) PCB SOLDER .40 .40 PAD 1.65 1.65 1.65RECOMMENDED .40 THIRD ANGLE PROJECTION .40 .40 50 .50 1.30 1.30 1.30 3.30 3.30 3.30 6 .40 .40 .40 .40 .40 3.20 3.20 3.20 5 UNLESS OTHERWISE SP DIMENSIONS ARE IN MILLIMETERS AND AFTER TOLERANCE UNLESS SP .XX ± .25 .XXX ± .12 X° ± .5 FOR SHEET METAL PART .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 SURFACE FINISH: 1.6 DATE BY DATE DRAWN BY DRAWN BY DRAWN 4 UNLESS OTHERWISE SPECIFIED UNLESSUNLESS OTHERWISE SPECIFIED OTHERWISE SPECIFIED 3 DATE D. CRONIN 07/19/12 D. CRONIN 07/19/1207/19/12 D. CRONIN DIMENSIONS AREDIMENSIONS IN ARE IN ARE DIMENSIONS IN CHECK DATE CHECK DATE CHECK DATE MILLIMETERS AND AFTER FINISH. MILLIMETERS AND AFTER MILLIMETERS ANDFINISH. AFTER FINISH. TOLERANCE UNLESS SPECIFIED: UNLESS SPECIFIED: ® ® TOLERANCE SPECIFIED: RECOMMENDED STENCIL PATTERN RECOMMENDED RECOMMENDED STENCIL PATTERN Copyright © 2012 Cree, Inc. All rights reserved. The information in this document isSTENCIL subject toPATTERN change without notice. Cree , theTOLERANCE Cree logo and UNLESS XLamp are registered trademarks .XX ± .XX.25 ± .XX .25± .25 COMMENDED PCB Inc. SOLDER RECOMMENDED PCB SOLDER PAD PAD (HATCHED AREAAREA IS OPENING) of Cree, RECOMMENDED PCBPAD SOLDER (HATCHED IS OPENING) (HATCHED AREA IS OPENING) .XXX ± .XXX .125 ±.XXX.125± .125 DATE APPROVEDAPPROVED DATE DATE APPROVED TITLE TITLE X° ± X° .5 °± X° .5 ±° .5 ° THIRD ANGLE PROJECTION THIRD THIRD ANGLEANGLE PROJECTION PROJECTION MATERIAL MATERIALMATERIAL FOR SHEET METAL PARTS ONLY FOR SHEET METAL PARTS FOR SHEET METALONLY PARTS ONLY .X ± .X 1.5± .X 1.5 ± 1.5 SIZE .XX ± .XX.75 ± .XX .75± .75 .XXX ± .XXX .25 ±.XXX.25 ±FINAL .25 PROTECTIVE FINALFINISH PROTECTIVE FINISH FINAL PROTECTIVE FINISH TITLE OUTLINE DRA OUTLINE OUT 10 SIZE DRAWING NO. DRAW SIZE C C C261 DETAIL B SCALE 2 : 1 xlamp xp-e2 leds 1.50 2.00 [.079] P2 +.10 +.0039 4.00 [.157] Po -.00[.0591-.0000]Do 1.75 [.069] E1 Tape and Reel 4.39 [.173] 3.7 +/-0.1mm Bo 12.00 [.472] All Cree carrier tapes conform to5.50EIA-481D, Automated Component Handling Systems Standard. [.217]F NOMINAL 12.30 [.484] MAX 2.00 [.079] W P2 10.25 [.404] E2 +.10 +.0039 1.50 4.00 [.157] Po 1.50 [.059] D1 8.00 [.315] P +.10 -.00[ 4.0±.1 .096 +.0039 -.0000] 4.39 [.173] .30 [.012] T 4.00 [.157]4.00 [.157] Po Po 2.46 4.39 [.173] 1.75 [.069] E1 +.10 +.0039 +.10 +.0039 1.50 -.00[.0591-.0000]Do -.00[.0591-.0000]Do 1.50 2.00 [.079]2.00 [.079] P2 P2 1.75 [.069]1.75 [.069] E1 E1 12.00 [.472] 5.50 [.217]F NOMINAL Ko POCKET SIZE 1.75±.10 Ao - 3.7 +/-0.1mm Ao Bo Ko - +.3 12.0 .0 4.39 [.173] 5.50 [.217]F 5.50 [.217]F 8.0±.1 3.7mm +/-0.1mm Cathode Side 3.7mm8.00 +/-0.1mm [.315] P 2.46mm +0.1/-0mm 8.00 [.315]8.00 [.315] P P 7.3 ° 2.46 7.3 ° Anode Side (denoted by + and circle) 3.7 +/-0.1mm Ao 4.39 [.173] 3.7 +/-0.1mm 3.7 +/-0.1mm Bo Bo 2.5±.1 +.10 +.0039 2.46 .096 -.00[ -.0000] 1.50 [.059]1.50 [.059] D1 D1 4.39 [.173]4.39 [.173] 3.7 +/-0.1mm Bo 12.30 [.484] 10.2512.30 [.484] MAX [.404] MAX W W E2 10.25 [.404] E2 1.50 [.059] D1 4.39 [.173] 12.30 [.484] MAX W 12.00 [.472] 12.00 [.472] NOMINALNOMINAL 10.25 [.404] E2 1.5±.1 7.3 ° All dimensions in mm. -.00[.0591-.0000]Do .30 [.012] T Ko .30 [.012] .30 [.012] T T +.10+.0039 +.0039 +.10 2.46.096 .096 Ko -.00[-.0000] -.0000] -.00[ 7.3 ° Ko POCKET SIZE Ao - 3.7mm +/-0.1mm Bo - 3.7mm +/-0.1mm 2.46mm +0.1/-0mm POCKET POCKET SIZE SIZE Ko - - 3.7mm +/-0.1mm Ao - Ao 3.7mm +/-0.1mm User Feed Direction 3.7 +/-0.1mm 3.7 +/-0.1mm Ao Ao END - 3.7mm +/-0.1mm Bo - Bo 3.7mm +/-0.1mm START +0.1/-0mm 2.46mm +0.1/-0mm - 2.46mm Ko - Ko Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) 6 Loaded Pockets (1,000 Lamps) 5 4 Leader 400mm (min) of empty pockets with at least2400-00009 100mm 2400-00009-CORE sealed by tape 2400-00009-REEL (50 empty pockets min.) 3 2 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTANED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. D INDEX QTY 1 2 1 2 1 ITEM COMMENTS User Feed Direction D Cover Tape 12.4 +.2 .0 MEASURED AT HUB C 330 +.25 -.75 C Pocket Tape 1.9±.4 16.4 +0.2 .0 MEASURED AT HUB 21 ±.4 13.1 ±.2 B B 13mm 12.4 +1.0 -.5 MEASURED AT EDGE 7" 60° 60° REVISONS REV BY DESCRIPTION DATE APP'D Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks A of Cree, Inc. THIRD ANGLE PROJECTION UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .01 .XXX ± .005 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± .06 .XX ± .03 .XXX ± .010 X° ± .5 ° SURFACE FINISH: 6 5 4 3 63 DATE DRAWN BY D. CRONIN 4600 Silicon Drive Durham, N.C 27703 09/29/09 CHECK DATE -- Phone (919) 313-5300 -- APPROVED Fax (919) 313-5558 A DATE -- -- MATERIAL ANTI-STATIC HIPS TITLE REEL, 13" X 12MM, 3 PIECE SNAP SIZE FINAL PROTECTIVE FINISH 2 SCALE C 0.500 REV. DRAWING NO. 2400-00009 SHEET 1 A OF 1 /1 11 xlamp xp-e2 leds Humidity Indicator Card (inside bag) Packaging Dessicant (inside bag) Unpackaged Reel Label with Cree Bin Code, Qty, Reel ID Packaged Reel Label with Cree Bin Code, Qty, Lot # Vacuum-Sealed Moisture Barrier Bag Label with Cree Order Code, Qty, Reel ID, PO # Label with Cree Bin Code, Qty, Reel ID Label with Custo Code, Qty, Reel Boxed Reel Label with Cree Order Code, Qty, Reel ID, PO # Patent Label Label with Cree Bin Code, Qty, Reel ID Patent Label Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 12