TPS40055-EP 8 www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 WIDE-INPUT SYNCHRONOUS BUCK CONTROLLER Check for Samples: TPS40055-EP FEATURES APPLICATIONS • • • • • • • 1 2 • • • • • • • Operating Input Voltage 8 V to 40 V Input Voltage Feed-Forward Compensation < 1 % Internal 0.7-V Reference Programmable Fixed-Frequency Up to 1-MHz Voltage Mode Controller Internal Gate Drive Outputs for High-Side and Synchronous N-Channel MOSFETs 16-Pin PowerPAD™ Package (θJC = 25°C/W) Thermal Shutdown Externally Synchronizable Programmable High-Side Sense Short-Circuit Protection Programmable Closed-Loop Soft-Start TPS40055 Source/Sink SUPPORTS DEFENSE, AEROSPACE, AND MEDICAL APPLICATIONS • • • • • • • (1) Controlled Baseline One Assembly/Test Site One Fabrication Site Available in Military (–55°C/125°C) Temperature Range (1) Extended Product Life Cycle Extended Product-Change Notification Product Traceability Power Modules Networking/Telecom Industrial/Servers DESCRIPTION The TPS40055 is a family of high-voltage, wide input (8 V to 40 V), synchronous, step-down converters. The TPS40055 family offers design flexibility with a variety of user programmable functions, including soft-start, UVLO, operating frequency, voltage feedforward, high-side current limit, and loop compensation. The TPS40055 are also synchronizable to an external supply. The TPS40055 incorporates MOSFET gate drivers for external N-channel high-side and synchronous rectifier (SR) MOSFETs. Gate drive logic incorporates anti-cross conduction circuitry to prevent simultaneous high-side and synchronous rectifier conduction. The TPS40055 uses voltage feed-forward control techniques to provide good line regulation over the wide (4:1) input voltage range and fast response to input line transients with near constant gain with input variation which eases loop compensation. The externally programmable current limit provides pulseby-pulse current limit, as well as a hiccup mode operation utilizing an internal fault counter for longer duration overloads. Additional temperature ranges available - contact factory 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2005–2012, Texas Instruments Incorporated TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com SIMPLIFIED APPLICATION DIAGRAM TPS40055 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) (1) (2) (3) (4) 2 TA APPLICATION (2) PACKAGE (3) (4) PART NUMBER –55°C to 125°C SOURCE/SINK Plastic HTSSOP (PWP) TPS40055MPWPREP For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI Web site at www.ti.com. See Application Information section. Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. The PWP package is also available taped and reeled. Add an R suffix to the device type. See the application section of the data sheet for PowerPAD drawing and layout information. Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP TPS40055-EP www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) VALUE / UNIT VIN VIN Input voltage range 45 V VFB, SS, SYNC –0.3 V to 6 V SW –0.3 V to 45 V SW, transient < 50 ns –2.5 V KFF, with IIN(max) = –5 mA –0.3 V to 11 V VOUT Output voltage range COMP, RT, SS –0.3 V to 6 V IIN Input current KFF IOUT Output current RT TJ Operating junction temperature range –55°C to 140°C Tstg Storage temperature (2) –55°C to 150°C 5 mA 200 µA Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds TJC Thermal resistance junction-to-case TJA Thermal resistance junction-to-ambient TJP Thermal resistance junction-to-bottom of thermal pad φJT (1) (2) (3) (4) Junction-to-top thermal parameter 260°C 26.6°C/W (3) (4) 36.5°C/W (3) 2.1°C/W (3) (4) 0.848°C/W Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Long-term high-temperature storage and/or extended use at maximum recommended operating conditions may result in reduced overall device life. See http://www.ti.com/ep_quality for additional information on enhanced plastic packaging. See technical brief SLMA002 - PowerPAD Thermally Enhanced Package(http://www-s.ti.com/sc/techlit/slma002). Tested in accordance with the thermal metric definitions of EIA/JESD51-5. RECOMMENDED OPERATING CONDITIONS MIN VI Input voltage TA Operating free-air temperature NOM MAX UNIT 8 40 V –55 125 °C ELECTRICAL CHARACTERISTICS TA = –55°C to 125°C, VIN = 24 Vdc, RT = 90.9 kΩ, IKFF = 150 µA, fSW = 500 kHz, all parameters at zero power dissipation (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT INPUT SUPPLY VIN Input voltage range, VIN 8 40 V 1.5 3.3 mA OPERATING CURRENT IDD Output drivers not switching, VFB ≥ 0.75 V Quiescent current BP5 VBP5 Output voltage OSCILLATOR/RAMP GENERATOR IOUT ≤ 1 mA 4.7 5 5.3 V 465 520 585 kHz (1) fOSC Accuracy 8 V ≤ VIN ≤ 40 V VRAMP PWM ramp voltage (2) VPEAK – VVAL VIH High-level input voltage, SYNC VIL Low-level input voltage, SYNC ISYNC Input current, SYNC 2 Pulse width, SYNC VRT (1) (2) 2 V 5 V 5 11 µA 2.5 2.59 50 RT voltage 2.37 V 0.8 ns V IKFF increases with SYNC frequency, IKFF decreases with maximum duty cycle. Ensured by design. Not production tested. Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP 3 TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com ELECTRICAL CHARACTERISTICS (continued) TA = –55°C to 125°C, VIN = 24 Vdc, RT = 90.9 kΩ, IKFF = 150 µA, fSW = 500 kHz, all parameters at zero power dissipation (unless otherwise noted) PARAMETER TEST CONDITIONS Maximum duty cycle VFB = 0 V, 500 kHz ≤ fSW ≤ 1 MHz Feed-forward voltage IKFF Feed-forward current operating range (2) TYP 84% (2) MAX UNIT 94% 80% VFB ≥ 0.75 V Minimum duty cycle VKFF MIN VFB = 0 V, fSW ≤ 500 kHz 0% 3.35 3.48 20 3.7 V 1200 µA 3.6 µA SOFT START ISS Soft-start source current VSS Soft-start clamp voltage 1.2 2.35 tDSCH Discharge time CSS = 220 pF 1.4 2.2 3.4 µs tSS Soft-start time CSS = 220 pF, 0 V ≤ VSS ≤ 1.6 V 102 150 230 µs Output voltage IOUT ≤ 1 mA 8.9 9.6 10.45 V 8 V ≤ VIN ≤ 40 V, TA = 25°C 0.698 0.7 0.704 8 V ≤ VIN ≤ 40 V, 0°C ≤ TA ≤ 125°C 0.689 0.7 0.717 8 V ≤ VIN ≤ 40 V, –55°C ≤ TA ≤ 125°C 0.689 0.7 0.719 2.8 5 MHz dB 3.7 V BP10 VBP10 ERROR AMPLIFIER VFB Feedback input voltage V GBW Gain bandwidth (3) AVOL Open loop gain 40 80 IOH High-level output source current 1.85 4 IOL Low-level output source current 1.95 4 VOH High-level output voltage ISOURCE = 500 µA 3.1 3.5 VOL Low-level output voltage ISINK = 500 µA 0.2 0.37 IBIAS Input bias current VFB = 0.7 V 100 220 nA 10 12.2 µA mA V CURRENT LIMIT ISINK Current limit sink current 7.5 Propagation delay to output tON Switch leading-edge blanking pulse time (3) tOFF Off time during a fault VOS Offset voltage SW vs ILIM VILIM = 23.7 V, VSW = (VILIM – 0.5 V) 300 VILIM = 23.7 V, VSW = (VILIM – 2 V) 200 ns 100 ns 7 –70 cycle s VILIM = 23.6 V, TA = 25°C –115 –50 VILIM = 23.6 V, 0°C ≤ TA ≤ 125°C –155 –38 VILIM = 23.6 V, –55°C ≤ TA ≤ 125°C –155 –10 VILIM = 11.6 V, TA = 25°C –118 –43 VILIM = 11.6 V, 0°C ≤ TA ≤ 125°C –160 –45 VILIM = 11.6 V, TA = –55°C to 125°C –160 –15 mV OUTPUT DRIVER tLRISE Low-side driver rise time tLFALL Low-side driver fall time tHRISE High-side driver rise time tHFALL High-side driver fall time VOH High-level output voltage, HDRV IHDRV = –0.1 A (HDRV - SW) VOL Low-level output voltage, HDRV IHDRV = 0.1 A (HDRV - SW) (3) 4 CLOAD = 2200 pF CLOAD = 2200 pF, (HDRV – SW) 48 110 24 58 48 105 36 82 BOOST BOOST –1.9 –1 ns ns V 0.85 V Ensured by design. Not production tested. Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP TPS40055-EP www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 ELECTRICAL CHARACTERISTICS (continued) TA = –55°C to 125°C, VIN = 24 Vdc, RT = 90.9 kΩ, IKFF = 150 µA, fSW = 500 kHz, all parameters at zero power dissipation (unless otherwise noted) PARAMETER TEST CONDITIONS VOH High-level output voltage, LDRV ILDRV = –0.1 A VOL Low-level output voltage, LDRV ILDRV = 0.1 A MIN TYP BP10 –1.8 BP10 –1 Minimum controllable pulse width MAX UNIT V 0.6 V 100 160 ns SS/SD SHUTDOWN VSD Shutdown threshold voltage VEN Device active threshold voltage Outputs off 85 125 170 mV 180 210 260 mV 30.8 32.2 33.9 V 35 µA BOOST REGULATOR VBOOST Output voltage VIN = 24 V SW NODE ILEAK Leakage current (4) THERMAL SHUTDOWN Shutdown temperature (4) TSD 165 Hysteresis (4) °C 20 UVLO VUVLO VDD (4) KFF programmable threshold voltage RKFF = 28.7 kΩ UVLO, fixed UVLO, hysteresis 6.85 7.5 7.95 7.05 7.5 7.9 V 0.46 Ensured by design. Not production tested. TYPICAL CHARACTERISTICS OFFSET VOLTAGE (VLim vs SW) TEMPERATURE Figure 1. Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP 5 TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com DEVICE INFORMATION (1) For more information on the PWP package, see the Texas Instruments Technical Brief (SLMA002) (2) PowerPAD heat slug must be connected to SGND (pin 5) or electrically isolated from all other pins. TERMINAL FUNCTIONS TERMINAL I/O DESCRIPTION 14 O Gate drive voltage for the high side N-channel MOSFET. The BOOST voltage is 9 V greater than the input voltage. A 0.1-µF ceramic capacitor should be connected from this pin to the drain of the lower MOSFET. BP5 3 O 5-V reference. This pin should be bypassed to ground with a 0.1-µF ceramic capacitor. This pin may be used with an external dc load of 1 mA or less. BP10 11 O 10-V reference used for gate drive of the N-channel synchronous rectifier. This pin should be bypassed by a 1µF ceramic capacitor. This pin may be used with an external dc load of 1 mA or less. COMP 8 O Output of the error amplifier, input to the PWM comparator. A feedback network is connected from this pin to the VFB pin to compensate the overall loop. The COMP pin is internally clamped above the peak of the ramp to improve large signal transient response. HDRV 13 O Floating gate drive for the high-side N-channel MOSFET. This pin switches from BOOST (MOSFET on) to SW (MOSFET off). ILIM 16 I Current limit pin used to set the overcurrent threshold. An internal current sink from this pin to ground sets a voltage drop across an external resistor connected from this pin to VCC. The voltage on this pin is compared to the voltage drop (VIN -SW) across the high side MOSFET during conduction. KFF 1 I A resistor is connected from this pin to VIN to program the amount of voltage feed-forward. The current fed into this pin is internally divided and used to control the slope of the PWM ramp. LDRV 10 O Gate drive for the N-channel synchronous rectifier. This pin switches from BP10 (MOSFET on) to ground (MOSFET off). PGND 9 – Power ground reference for the device. There should be a low-impedance path from this pin to the source(s) of the lower MOSFET(s). RT 2 I A resistor is connected from this pin to ground to set the internal oscillator and switching frequency. SGND 5 – Signal ground reference for the device NAME NO. BOOST SS/SD 6 I Soft-start programming pin. A capacitor connected from this pin to ground programs the soft-start time. The capacitor is charged with an internal current source of 2.3 µA. The resulting voltage ramp on the SS pin is used as a second non-inverting input to the error amplifier. The output voltage begins to rise when VSS/SD is approximately 0.85 V. The output continues to rise and reaches regulation when VSS/SD is approximately 1.55 V. The controller is considered shut down when VSS/SD is 125 mV or less. All internal circuitry is inactive. The internal circuitry is enabled when VSS/SD is 210 mV or greater. When VSS/SD is less than approximately 0.85 V, the outputs cease switching and the output voltage (VOUT) decays while the internal circuitry remains active. SW 12 I This pin is connected to the switched node of the converter and used for overcurrent sensing. 6 Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP TPS40055-EP www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 TERMINAL FUNCTIONS (continued) TERMINAL I/O DESCRIPTION NAME NO. SYNC 4 I Synchronization input for the device. This pin can be used to synchronize the oscillator to an external master frequency. If synchronization is not used, connect this pin to SGND. VFB 7 I Inverting input to the error amplifier. In normal operation, the voltage on this pin is equal to the internal reference voltage, 0.7 V. VIN 15 I Supply voltage for the device SIMPLIFIED BLOCK DIAGRAM 0.7 VREF 0.85 V Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP 7 TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com APPLICATION INFORMATION The TPS40055 allows the user to optimize the PWM controller to the specific application. The TPS40055 is the controller of choice for synchronous buck designs, which includes most applications. It has two quadrant operations and will source or sink output current. This provides the best transient response. SETTING THE SWITCHING FREQUENCY (PROGRAMMING THE CLOCK OSCILLATOR) The TPS40055 has independent clock oscillator and ramp generator circuits. The clock oscillator serves as the master clock to the ramp generator circuit. The switching frequency, fSW in kHz, of the clock oscillator is set by a single resistor (RT) to ground. The clock frequency is related to RT, in kΩ by Equation 1 and the relationship is charted in Figure 3. (1) PROGRAMMING THE RAMP GENERATOR CIRCUIT The ramp generator circuit provides the actual ramp used by the PWM comparator. The ramp generator provides voltage feed-forward control by varying the PWM ramp slope with line voltage, while maintaining a constant ramp magnitude. Varying the PWM ramp directly with line voltage provides excellent response to line variations since the PWM does not have to wait for loop delays before changing the duty cycle. (See Figure 2 ). Figure 2. Voltage Feed-Forward Effect on PWM Duty Cycle The PWM ramp must be faster than the master clock frequency or the PWM is prevented from starting. The PWM ramp time is programmed via a single resistor (RKFF) pulled up to VIN. RKFF is related to RT and the minimum input voltage (VIN(min)) through the following: (2) where: VIN(min) is the ensured minimum start-up voltage. The actual start-up voltage is nominally about 10% lower at 25°C. 8 Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP TPS40055-EP www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 RT is the timing resistance in kΩ. The curve showing the RKFF required for a given switching frequency (fSW) is shown in Figure 4. For low input voltage and high duty cycle applications, the voltage feed-forward may limit the duty cycle prematurely. This does not occur for most applications. The voltage control loop controls the duty cycle and regulates the output voltage. For more information on large duty cycle operation, see the application note (SLUA310). SWITCHING FREQUENCY vs TIMING RESISTANCE Figure 3. FEED-FORWARD IMPEDANCE vs SWITCHING FREQUENCY Figure 4. UVLO OPERATION The TPS40055 uses variable (user programmable) UVLO protection. The UVLO circuit holds the soft-start low until the input voltage has exceeded the user programmable undervoltage threshold. The TPS40055 uses the feed-forward pin, KFF, as a user programmable low-line UVLO detection. This variable low-line TPS40055 uses variable (user programmable) UVLO protection. The UVLO circuit holds the soft-start low until the input voltage has exceeded the user programmable undervoltage threshold. UVLO threshold compares the PWM ramp duration to the oscillator clock period. An undervoltage condition exists if the TPS40055 receives a clock pulse before the ramp has reached 90% of its full amplitude. The ramp duration is a function of the ramp slope, which is directly related to the current into the KFF pin. The KFF current is a function of the input voltage and the resistance from KFF to the input voltage. The KFF resistor can be referenced to the oscillator frequency as described in Equation 3: (3) where: VIN is the desired start-up (UVLO) input voltage RT is the timing resistance in kΩ The variable UVLO function uses a 3-bit full adder to prevent spurious shut-downs or turn-ons due to spikes or fast line transients. When the adder reaches a total of seven counts in which the ramp duration is shorter than the clock cycle a power-good signal is asserted and a soft-start initiated and the upper and lower MOSFETS are turned off. Once the soft-start is initiated, the UVLO circuit must see a total count of seven cycles in which the ramp duration is longer than the clock cycle before an undervoltage condition is declared. (See Figure 5 ). Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP 9 TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com Figure 5. Undervoltage Lockout Operation The tolerance on the UVLO set point also affects the maximum duty cycle achievable. If the UVLO starts the device at 10% below the nominal start up voltage, the maximum duty cycle is reduced approximately 10% at the nominal start up voltage. The impedance of the input voltage can cause the input voltage, at the controller, to sag when the converter starts to operate and draw current from the input source. Therefore, there is voltage hysteresis that prevents nuisance shutdowns at the UVLO point. With RT chosen to select the operating frequency and RKFF chosen to select the start-up voltage, the approximate amount of hysteresis voltage is shown in Figure 7. Figure 6. UNDERVOLTAGE LOCKOUT THRESHOLD vs HYSTERESIS Figure 7. BP5 AND BP10 INTERNAL VOLTAGE REGULATORS Start-up characteristics of the BP5 and BP10 regulators over different temperature ranges are shown in Figure 8 and Figure 9. Slight variations in the BP5 occurs dependent upon the switching frequency. Variation in the BP10 regulation characteristics is also based on the load presented by switching the external MOSFETs. 10 Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP TPS40055-EP www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 INPUT VOLTAGE vs BP5 VOLTAGE INPUT VOLTAGE vs BP10 VOLTAGE Figure 8. Figure 9. SELECTING THE INDUCTOR VALUE The inductor value determines the magnitude of ripple current in the output capacitors as well as the load current at which the converter enters discontinuous mode. Too large an inductance results in lower ripple current but is physically larger for the same load current. Too small an inductance results in larger ripple currents and a greater number of (or more expensive output capacitors for) the same output ripple voltage requirement. A good compromise is to select the inductance value such that the converter does not enter discontinuous mode until the load approximated somewhere between 10% and 30% of the rated output. The inductance value is described in Equation 4. (4) where: VO is the output voltage ΔI is the peak-to-peak inductor current CALCULATING THE OUTPUT CAPACITANCE The output capacitance depends on the output ripple voltage requirement, output ripple current, as well as any output voltage deviation requirement during a load transient. The output ripple voltage is a function of both the output capacitance and capacitor ESR. The worst case output ripple is described in Equation 5. (5) The output ripple voltage is typically between 90% and 95% due to the ESR component. The output capacitance requirement typically increases in the presence of a load transient requirement. During a step load, the output capacitance must provide energy to the load (light-to-heavy load step) or absorb excess inductor energy (heavy-to-light load step) while maintaining the output voltage within acceptable limits. The amount of capacitance depends on the magnitude of the load step, the speed of the loop and the size of the inductor. Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP 11 TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com Stepping the load from a heavy load to a light load results in an output overshoot. Excess energy stored in the inductor must be absorbed by the output capacitance. The energy stored in the inductor is described in Equation 6. (6) where: (7) IOH is the output current under heavy load conditions IOL is the output current under light load conditions Some applications may require an additional circuit to prevent false restarts at the UVLO voltage level. This applies to applications which have high impedance on the input voltage line or which have excessive ringing on the VIN line. The input voltage impedance can cause the input voltage to sag enough at start-up to cause a UVLO shutdown and subsequent restart. Excessive ringing can also affect the voltage seen by the device and cause a UVLO shutdown and restart. A simple external circuit provides a selectable amount of hysteresis to prevent the nuisance UVLO shutdown. Assuming a hysteresis current of 10% IKFF and the peak detector charges to 8 V and VIN(min) = 10 V, the value of RA is calculated by Equation 8 using a RKFF = 71.5 kΩ. (8) CA is chosen to maintain the peak voltage between switching cycles. To keep the capacitor charge from drooping 0.1 V, or from 8 V to 7.9 V. (9) The value of CA may calculate to less than 10 pF, but some standard value up to 47 pF works adequately. The diode can be a small signal switching diode or Schottky rated for more then 20 V. Figure 10 illustrates a typical implementation using a small switching diode. The tolerance on the UVLO set point also affects the maximum duty cycle achievable. If the UVLO starts the device at 10% below the nominal start up voltage, the maximum duty cycle is reduced approximately 10% at the nominal start up voltage. 12 Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP TPS40055-EP www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 + VIN − RA 499 kW RKFF 71.5 kW CA 47 pF 1 KFF ILIM 16 2 RT VIN 15 3 BP5 BOOST 14 4 SYNC HDRV 13 5 SGND SW 12 6 SS BP10 11 7 VFB LDRV 10 8 COMP PGND 9 PWP DA 1N914, 1N4150 Type Signal Diode UDG−03034 Figure 10. Hysteresis for Programmable UVLO Energy in the capacitor is described in Equation 10. (10) where: (11) where: Vf is the final peak capacitor voltage VI is the initial capacitor voltage Substituting Equation 7 into Equation 6, then substituting Equation 11 into Equation 10, then setting Equation 10 equal to Equation 6, and then solving for CO yields the capacitance described in Equation 12. (12) PROGRAMMING SOFT START TPS40055 uses a closed-loop approach to ensure a controlled ramp on the output during start-up. Soft-start is programmed by charging an external capacitor (CSS) via an internally generated current source. The voltage on CSS minus 0.85 V is fed into a separate non-inverting input to the error amplifier (in addition to FB and 0.7-V VREF). The loop is closed on the lower of the (CSS – 0.85 V) voltage or the internal reference voltage (0.7-V VREF). Once the (CSS – 0.85 V) voltage rises above the internal reference voltage, regulation is based on the internal reference. To ensure a controlled ramp-up of the output voltage the soft-start time should be greater than the L-CO time constant as described in Equation 13. (13) Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP 13 TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com There is a direct correlation between tSTART and the input current required during start-up. The faster tSTART, the higher the input current required during start-up. This relationship is describe in more detail in the section titled, Programming the Current Limit which follows. The soft-start capacitance, CSS, is described in Equation 14. (14) For applications in which the VIN supply ramps up slowly, (typically between 50 ms and 100 ms) it may be necessary to increase the soft-start time to between approximately 2 ms and 5 ms to prevent nuisance UVLO tripping. The soft-start time should be longer than the time that the VIN supply transitions between 6 V and 7 V. PROGRAMMING CURRENT LIMIT The TPS40055 uses a two-tier approach for overcurrent protection. The first tier is a pulse-by-pulse protection scheme. Current limit is implemented on the high-side MOSFET by sensing the voltage drop across the MOSFET when the gate is driven high. The MOSFET voltage is compared to the voltage dropped across a resistor connected from VIN pin to the ILIM pin when driven by a constant current sink. If the voltage drop across the MOSFET exceeds the voltage drop across the ILIM resistor, the switching pulse is immediately terminated. The MOSFET remains off until the next switching cycle is initiated. The second tier consists of a fault counter. The fault counter is incremented on an overcurrent pulse and decremented on a clock cycle without an overcurrent pulse. When the counter reaches seven, a restart is issued and seven soft-start cycles are initiated. Both the upper and lower MOSFETs are turned off during this period. The counter is decremented on each soft-start cycle. When the counter is decremented to zero, the PWM is reenabled. If the fault has been removed the output starts up normally. If the output is still present, the counter counts seven overcurrent pulses and re-enters the second-tier fault mode. See Figure 11 for typical overcurrent protection waveforms. The minimum current limit setpoint (ILIM) depends on tSTART, CO, VO, and the load current at turn-on (IL). (15) Figure 11. Typical Current Limit Protection Waveforms The current limit programming resistor (RILIM) is calculated using Equation 16. Care must be taken in choosing the values used for VOS and ISINK in the equation. In order to assure the output current at the overcurrent level, the minimum value of ISINK and the maximum value of VOS must be used. 14 Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP TPS40055-EP www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 (16) where: ISINK is the current into the ILIM pin and is 7.5 µA, minimum IOC is the overcurrent setpoint which is the dc output current plus one-half of the peak inductor current VOS is the overcurrent comparator offset and is –20 mV, maximum SYNCHRONIZING TO AN EXTERNAL SUPPLY The TPS40055 can be synchronized to an external clock through the SYNC pin. Synchronization occurs on the falling edge of the SYNC signal. The synchronization frequency should be in the range of 20% to 30% higher than its programmed free-run frequency. The clock frequency at the SYNC pin replaces the master clock generated by the oscillator circuit. Pulling the SYNC pin low programs the TPS40055 to freely run at the frequency programmed by RT. The higher synchronization must be factored in when programming the PWM ramp generator circuit. If the PWM ramp is interrupted by the SYNC pulse, a UVLO condition is declared and the PWM becomes disabled. Typically this is of concern under low-line conditions only. In any case, RKFF needs to be adjusted for the higher switching frequency. In order to specify the correct value for RKFF at the synchronizing frequency, calculate a dummy value for RT that would cause the oscillator to run at the synchronizing frequency. Do not use this value of RT in the design. (17) Use the value of RT(dummy) to calculate the value for RKFF. (18) This value of RKFF ensures that UVLO is not engaged when operating at the synchronization frequency. RT(dummy) is in kΩ Loop Compensation Voltage-mode buck-type converters are typically compensated using Type III networks. Since the TPS40055 uses voltage feedforward control, the gain of the PWM modulator with voltage feedforward circuit must be included. The modulator gain is described in Figure 11, with VIN being the minimum input voltage required to cause the ramp excursion to cover the entire switching period as described in Equation 19. (19) Duty cycle (D) varies from 0 to 1 as the control voltage (VC) varies from the minimum ramp voltage to the maximum ramp voltage (VS). Also, for a synchronous buck converter, D = VO / VIN. To get the control voltage to output voltage modulator gain in terms of the input voltage and ramp voltage: (20) Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP 15 TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com Calculate the Poles and Zeros For a buck converter using voltage mode control, there is a double pole due to the output L-CO. The double pole is located at the frequency calculated in Equation 21. (21) There is also a zero created by the output capacitance (CO) and its associated ESR. The ESR zero is located at the frequency calculated in Equation 22. (22) Calculate the value of RBIAS to set the output voltage (VOUT). (23) The maximum crossover frequency (0 dB loop gain) is calculated in Equation 24. (24) Typically, fC is selected to be close to the midpoint between the L-CO double pole and the ESR zero. At this frequency, the control to output gain has a -2 slope (–40 dB/decade), while the Type III topology has a +1 slope (20 dB/decade), resulting in an overall closed loop –1 slope (–20 dB/decade). Figure 13 shows the modulator gain, L-C filter, output capacitor ESR zero, and the resulting response to be compensated. MODULATOR GAIN vs SWITCHING FREQUENCY Figure 12. PWM Modulator Relationships Figure 13. A Type III topology, shown in Figure 14, has 2 zero-pole pairs in addition to a pole at the origin. The gain and phase boost of a Type III topology is shown in Figure 15. The two zeros are used to compensate the L-CO double pole and provide phase boost. The double pole is used to compensate for the ESR zero and provide controlled gain roll-off. In many cases, the second pole can be eliminated and the amplifier's gain roll-off used to roll-off the overall gain at higher frequencies. Figure 14. 16 Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP TPS40055-EP www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 Figure 14. Type III Compensation Configuration Figure 15. Type III Compensation Gain and Phase The poles and zeros for a Type III network are described in Equation 25. (25) The value of R1 is somewhat arbitrary, but influences other component values. A value between 50 kΩ and 100 kΩ usually yields reasonable values. The unity gain frequency is described in Equation 26. (26) where G is the reciprocal of the modulator gain at fC. The modulator gain as a function of frequency at fC, is described in Equation 27. (27) Minimum Load Resistance Care must be taken not to load down the output of the error amplifier with the feedback resistor, R2, that is too small. The error amplifier has a finite output source and sink current, which must be considered when sizing R2. Too small a value does not allow the output to swing over its full range. (28) CALCULATING THE BOOST AN BP10 BYPASS CAPACITOR The BOOST capacitance provides a local, low impedance source for the high-side driver. The BOOST capacitor should be a good quality, high-frequency capacitor. The size of the bypass capacitor depends on the total gate charge of the MOSFET and the amount of droop allowed on the bypass capacitor. The BOOST capacitance is described in Equation 29. (29) Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP 17 TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com The 10-V reference pin, BP10V provides energy for both the synchronous MOSFET and the high-side MOSFET via the BOOST capacitor. Neglecting any efficiency penalty, the BP10V capacitance is described in Equation 30. (30) dv/dt INDUCED TURN-ON MOSFETs are susceptible to dv/dt turn-on particularly in high-voltage (VDS) applications. The turn-on is caused by the capacitor divider that is formed by CGD and CGS. High dv/dt conditions and drain-to-source voltage, on the MOSFET causes current flow through CGD and causes the gate-to-source voltage to rise. If the gate-to-source voltage rises above the MOSFET threshold voltage, the MOSFET turns on, resulting in large shoot-through currents. Therefore, the SR MOSFET should be chosen so that the CGD capacitance is smaller than the CGS capacitance. HIGH SIDE MOSFET POWER DISSIPATION The power dissipated in the external high-side MOSFET is comprised of conduction and switching losses. The conduction losses are a function of the IRMS current through the MOSFET and the RDS(on) of the MOSFET. The high-side MOSFET conduction losses are defined by Equation 31. (31) where: TCR is the temperature coefficient of the MOSFET RDS(on) The TCR varies depending on MOSFET technology and manufacturer, but typically ranges between 3500 ppm/°C and 10000 ppm/°C. The IRMS current for the high side MOSFET is described in Equation 32. (32) The switching losses for the high-side MOSFET are described in Equation 33. (33) where: IO is the dc-output current tSW is the switching rise time, typically < 20 ns fSW is the switching frequency Typical switching waveforms are shown in Figure 16. 18 Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP TPS40055-EP www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 ID2 } IO ID1 d BODY DIODE CONDUCTION ∆I 1−d BODY DIODE CONDUCTION SW 0 ANTI−CROSS CONDUCTION SYNCHRONOUS RECTIFIER ON HIGH SIDE ON UDG−02139 Figure 16. Inductor Current and SW Node Waveforms The maximum allowable power dissipation in the MOSFET is determined by Equation 34. (34) where: (35) and θJA is the package thermal impedance. SYNCHRONOUS RECTIFIER MOSFET POWER DISSIPATION The power dissipated in the synchronous rectifier MOSFET is comprised of three components: RDS(on) conduction losses, body diode conduction losses, and reverse recovery losses. RDS(on) conduction losses can be found using Equation 31 and the RMS current through the synchronous rectifier MOSFET is described in Equation 36. (36) The body-diode conduction losses are due to forward conduction of the body diode during the anti-cross conduction delay time. The body diode conduction losses are described by Equation 37. (37) where: VF is the body diode forward voltage tDELAY is the delay time just before the SW node rises The 2-multiplier is used because the body diode conducts twice during each cycle (once on the rising edge and once on the falling edge). The reverse recovery losses are due to the time it takes for the body diode to recovery from a forward bias to a reverse blocking state. The reverse recovery losses are described in Equation 38. (38) where: QRR is the reverse recovery charge of the body diode. Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP 19 TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com The QRR is not always described in a MOSFET's data sheet, but may be obtained from the MOSFET vendor. The total synchronous rectifier MOSFET power dissipation is described in Equation 39. (39) TPS40055 POWER DISSIPATION The power dissipation in the TPS40055 is largely dependent on the MOSFET driver currents and the input voltage. The driver current is proportional to the total gate charge, Qg, of the external MOSFETs. Driver power (neglecting external gate resistance)[2] can be calculated from Equation 40. (40) And the total power dissipation in the TPS40055, assuming the same MOSFET is selected for both the high-side and synchronous rectifier is described in Equation 41. (41) or (42) where: IQ is the quiescent operating current (neglecting drivers) The maximum power capability of the device's PowerPad package is dependent on the layout as well as air flow. The thermal impedance from junction to air, assuming 2 oz. copper trace and thermal pad with solder and no air flow. (43) The maximum allowable package power dissipation is related to ambient temperature by Equation 44. (44) Substituting Equation 45 into Equation 41 and solving for fSW yields the maximum operating frequency for the TPS40055. The result is described in Equation 45. (45) LAYOUT CONSIDERATIONS PowerPAD™ PACKAGE The PowerPAD package provides low thermal impedance for heat removal from the device. The PowerPAD derives its name and low thermal impedance from the large bonding pad on the bottom of the device. For maximum thermal performance, the circuit board must have an area of solder-tinned-copper underneath the package. The dimensions of this area depends on the size of the PowerPAD package. For a 16-pin TSSOP (PWP) package, dimensions of the circuit board pad area are 5 mm x 3,4 mm [2]. The dimensions of the package pad are shown in Figure 17. 20 Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP TPS40055-EP www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 Thermal vias connect this area to internal or external copper planes and should have a drill diameter sufficiently small so that the via hole is effectively plugged when the barrel of the via is plated with copper. This plug is needed to prevent wicking the solder away from the interface between the package body and the solder-tinned area under the device during solder reflow. Drill diameters of 0,33 mm (13 mils) works well when 1-oz copper is plated at the surface of the board while simultaneously plating the barrel of the via. If the thermal vias are not plugged when the copper plating is performed, then a solder mask material should be used to cap the vias with a diameter equal to the via diameter of 0,1 mm minimum. This capping prevents the solder from being wicked through the thermal vias and potentially creating a solder void under the package. See the PowerPAD Thermally Enhanced Package and the mechanical illustration at the end of this document for more information on the PowerPAD package. Figure 17. PowerPAD Dimensions MOSFET PACKAGING MOSFET package selection depends on MOSFET power dissipation and the projected operating conditions. In general, for a surface-mount applications, the DPAK style package provides the lowest thermal impedance (θJA) and, therefore, the highest power dissipation capability. However, the effectiveness of the DPAK depends on proper layout and thermal management. The θJA specified in the MOSFET data sheet refers to a given copper area and thickness. In most cases, a lowest thermal impedance of 40°C/W requires one square inch of 2-ounce copper on a G-10/FR-4 board. Lower thermal impedances can be achieved at the expense of board area. See the selected MOSFET's data sheet for more information regarding proper mounting. GROUNDING AND CIRCUIT LAYOUT CONSIDERATIONS The TPS40055 provides separate signal ground (SGND) and power ground (PGND) pins. It is important that circuit grounds are properly separated. Each ground should consist of a plane to minimize its impedance if possible. The high power noisy circuits such as the output, synchronous rectifier, MOSFET driver decoupling capacitor (BP10), and the input capacitor should be connected to PGND plane at the input capacitor. Sensitive nodes such as the FB resistor divider, RT, and ILIM should be connected to the SGND plane. The SGND plane should only make a single point connection to the PGND plane. Component placement should ensure that bypass capacitors (BP10 and BP5) are located as close as possible to their respective power and ground pins. Also, sensitive circuits such as FB, RT, and ILIM should not be located near high dv/dt nodes such as HDRV, LDRV, BOOST, and the switch node (SW). Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP 21 TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com DESIGN EXAMPLE • • • • • • • Input Voltage: 10 Vdc to 24 Vdc Output voltage: 3.3 V +2% (3.234 ≤ VO ≤ 3.366) Output current: 8 A (maximum, steady state), 10 A (surge, 10-ms duration, 10% duty cycle maximum) Output ripple: 33 mVP-P at 8 A Output load response: 0.3 V => 10% to 90% step load change, from 1 A to 7 A Operating temperature: -40°C to 85°C fSW = 300 kHz 1. Calculate maximum and minimum duty cycles (46) 2. Select switching frequency The switching frequency is based on the minimum duty cycle ratio and the propagation delay of the current limit comparator. In order to maintain current limit capability, the on time of the upper MOSFET (tON) must be greater than 300 ns (see the Electrical Characteristics table). Therefore, (47) (48) Using 400 ns to provide margin, (49) Since the oscillator can vary by 10%, decrease fSW by 10% (50) and therefore choose a frequency of 300 kHz. 3. Select ΔI In this case ΔI is chosen so that the converter enters discontinuous mode at 20% of nominal load. (51) 4. Calculate the power losses Power losses in the high-side MOSFET (Si7860DP) at 24-VIN where switching losses dominate can be calculated from Equation 52. (52) substituting Equation 34 into Equation 33 yields (53) 22 Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP TPS40055-EP www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 and from Equation 33, the switching losses can be determined. (54) The MOSFET junction temperature can be found by substituting Equation 35 into Equation 34 (55) 5. Calculate synchronous rectifier losses The synchronous rectifier MOSFET has two loss components: conduction and diode reverse recovery losses. The conduction losses are due to IRMS losses, as well as body diode conduction losses during the dead time associated with the anti-cross conduction delay. The IRMS current through the synchronous rectifier from Equation 38 (56) The synchronous MOSFET conduction loss from Equation 33 is: (57) The body diode conduction loss from Equation 39 is: (58) The body diode reverse recovery loss from Equation 40 is: (59) The total power dissipated in the synchronous rectifier MOSFET from Equation 41 is: (60) The junction temperature of the synchronous rectifier at 85°C is: (61) In typical applications, paralleling the synchronous rectifier MOSFET with a Schottky rectifier increases the overall converter efficiency by approximately 2% due to the lower power dissipation during the body diode conduction and reverse recovery periods. 6. Calculate the inductor value The inductor value is calculated from Equation 62. (62) A 2.9-µH Coev DXM1306-2R9 or 2.6-µH Panasonic ETQ-P6F2R9LFA can be used. 7. Setting the switching frequency The clock frequency is set with a resistor (RT) from the RT pin to ground. The value of RT can be found from Equation 63, with fSW in kHz. (63) Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP 23 TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com 8. Programming the ramp generator circuit The PWM ramp is programmed through a resistor (RKFF) from the KFF pin to VIN. The ramp generator also controls the input UVLO voltage. For an undervoltage level of 10 V, RKFF can be calculated from Equation 64. W (64) 9. Calculating the output capacitance (CO) In this example the output capacitance is determined by the load response requirement of ΔV = 0.3 V for a 1-A to 8-A step load. CO can be calculated using Equation 65. (65) Using Equation 66, we can calculate the ESR required to meet the output ripple requirements. 97 (66) (67) For this design example, two Panasonic SP EEFUEOJ1B1R capacitors, (6.3 V, 180 µF, 12 mΩ) are used. 10. Calculate the soft-start capacitor (CSS) This design requires a soft-start time (tSTART) of 1 ms. CSS can be calculated on Equation 68 (68) 11. Calculate the current limit resistor (RILIM) The current limit set point depends on tSTART, VO, CO, and ILOAD at start-up as shown in Equation 69. For this design, (69) For this design, set ILIM for 11 ADC minimum. From Equation 70, with IOC equal to the dc-output surge current plus one-half the ripple current of 3.2 A and RDS(on) is increased 30% (1.3 × 0.008) to allow for MOSFET heating. (70) 12. Calculate loop compensation values Calculate the dc modulator gain (AMOD) from Equation 71 (71) Calculate the output filter L-CO poles and CO ESR zeros from Equation 72 and Equation 73 (72) and 24 Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP TPS40055-EP www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 (73) Select the close-loop 0 dB crossover frequency (fC). For this example, fC = 20 kHz. Select the double zero location for the Type III compensation network at the output filter double pole at 4.93 kHz. Select the double pole location for the Type III compensation network at the output capacitor ESR zero at 73.7 kHz. The amplifier gain at the crossover frequency of 20 kHz is determined by the reciprocal of the modulator gain AMOD at the crossover frequency from Equation 74. (74) And also from Equation 75. (75) Choose R1 = 100 kΩ The poles and zeros for a type III network are described in Equation 25 and Equation 26. (76) (77) (78) (79) (80) Calculate the value of RBIAS from Equation 81 with R1 = 100 kΩ. (81) CALCULATING THE BOOST AND BP10V BYPASS CAPACITANCE The size of the bypass capacitor depends on the total gate charge of the MOSFET being used and the amount of droop allowed on the bypass cap. The BOOST capacitance for the Si7860DP, allowing for a 0.5-V droop on the BOOST pin from Equation 29 is: (82) and the BP10V capacitance from Equation 32 is Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP 25 TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com (83) For this application, a 0.1-µF capacitor is used for the BOOST bypass capacitor and a 1-µF capacitor is used for the BP10V bypass. 26 Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP TPS40055-EP www.ti.com SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 DESIGN EXAMPLE SUMMARY Figure 18 shows component selection for the 10-V to 24-V to 3.3-V at 8 A dc-to-dc converter specified in the design example. For an 8-V input application, it may be necessary to add a Schottky diode from BP10 to BOOST to get sufficient gate drive for the upper MOSFET. As seen in Figure 9, the BP10 output is about 6 V with the input at 8 V, so the upper MOSFET gate drive may be less than 5 V. A Schottky diode is shown connected across the synchronous rectifier MOSFET as an optional device that may be required if the layout causes excessive negative SW node voltage, greater than or equal to 2 V. + RKFF 71.5 kW VIN 330 mF 13 kW 330 mF TPS40055 1N4150 499 kW RT 169 kW 1 KFF ILIM 16 2 RT VIN 15 100 pF 0.1 mF 47 pF 3 BP5 1.0 mF BOOST 14 22 mF 50 V 22 mF 50 V 1.0 kW 4 SYNC 1.0 mF Optional Hysteresis for UVLO CSS 3300 pF 5 SGND 6 SS C1 330 pF Si7860 2.9 mH + SW 12 R3 6.49 kW BP10 11 7 VFB R2 97.6 kW HDRV 13 Si7860 LDRV 10 1.0 mF R1 100 kW 180 mF *optional VOUT 180 mF C3 330 pF - 8 COMP C2 22 pF PGND 9 PWP RBIAS 26.7 kW Figure 18. 24 V to 3.3 V at 8-A DC-to-DC Converter Design Example REFERENCES 1. Balogh, Laszlo, Design and Application Guide for High Speed MOSFET Gate Drive Circuits, Texas Instruments/Unitrode Corporation, Power Supply Design Seminar, SEM-1400 Topic 2. 2. PowerPAD Thermally Enhanced Package Texas Instruments, Semiconductor Group, Technical Brief (SLMA002) Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP 27 TPS40055-EP SGLS310D – JULY 2005 – REVISED FEBRUARY 2012 www.ti.com REVISION HISTORY Changes from Revision C (February 2012) to Revision D • 28 Page Changed ISINK current minimum from 8.5 µA to 7.5 µA for equation 16 ............................................................................. 15 Submit Documentation Feedback Copyright © 2005–2012, Texas Instruments Incorporated Product Folder Link(s): TPS40055-EP PACKAGE OPTION ADDENDUM www.ti.com 29-Feb-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) TPS40055MPWPREP ACTIVE HTSSOP PWP 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS40055MPWPREPG4 ACTIVE HTSSOP PWP 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR V62/05617-01XE ACTIVE HTSSOP PWP 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TPS40055-EP : • Catalog: TPS40055 Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 29-Feb-2012 NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device TPS40055MPWPREP Package Package Pins Type Drawing SPQ HTSSOP 2000 PWP 16 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 330.0 12.4 Pack Materials-Page 1 6.9 B0 (mm) K0 (mm) P1 (mm) 5.6 1.6 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS40055MPWPREP HTSSOP PWP 16 2000 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated