TI TPS54160QDGQRQ1

TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
1.5-A 60-V STEP-DOWN SWIFT™ DC/DC CONVERTER
WITH Eco-Mode™ CONTROL
Check for Samples: TPS54160-Q1
FEATURES
1
•
•
•
•
•
•
•
•
•
•
Qualified for Automotive Applications
3.5-V to 60-V Input Voltage Range
200-mΩ High-Side MOSFET
High Efficiency at Light Loads With
Pulse-Skipping Eco-mode™ Control Scheme
116-μA Operating Quiescent Current
1.3-μA Shutdown Current
100-kHz to 2.5-MHz Switching Frequency
Synchronizes to External Clock
Adjustable Slow Start/Sequencing
Undervoltage and Overvoltage Power Good
Output
•
•
•
•
Adjustable Undervoltage Lockout (UVLO)
Voltage and Hysteresis
0.8-V Internal Voltage Reference
Supported by SwitcherPro™ Software Tool
(http://focus.ti.com/docs/toolsw/folders/print/s
witcherpro.html)
For SWIFT™ Documentation, See the TI
Website at http://www.ti.com/swift
APPLICATIONS
•
•
12-V, 24-V, and 48-V Industrial and Commercial
Low Power Systems
Aftermarket Automotive Accessories: Video,
GPS, Entertainment
DESCRIPTION
The TPS54160 device is a 60-V 1.5-A step-down regulator with an integrated high-side MOSFET. Current-mode
control provides simple external compensation and flexible component selection. A low-ripple pulse-skip mode
reduces the no load, regulated output supply current to 116 μA. Using the enable pin, shutdown supply current is
reduced to 1.3 μA.
Undervoltage lockout is set internally at 2.5 V but can be increased using the enable pin. The output voltage
startup ramp is controlled by the slow start pin that can also be configured for sequencing/tracking. An
open-drain power good signal indicates the output is within 93% to 107% of its nominal voltage.
A wide switching frequency range allows efficiency and external component size to be optimized. Frequency
foldback and thermal shutdown protects the part during an overload condition.
The TPS54160 is available in 10-pin thermally enhanced MSOP PowerPad (DGQ) or 10-pin SON (DRC)
package.
SIMPLIFIED SCHEMATIC
VIN
EFFICIENCY
vs
LOAD CURRENT
PWRGD
90
TPS54160
85
80
BOOT
PH
SS /TR
RT /CLK
COMP
Efficiency - %
EN
75
70
65
VI = 12 V,
VO = 3.3 V,
fsw = 1200 kHz
60
VSENSE
55
GND
50
0
0.25
0.50
0.75
1
1.25
Load Current - A
1.50
1.75
2
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009–2011, Texas Instruments Incorporated
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION (1)
PACKAGE (2)
TJ
–40°C to 150°C
(1)
(2)
ORDERABLE PART NUMBER
TOP-SIDE MARKING
MSOP – DGQ
Reel of 2500
TPS54160QDGQRQ1
5416Q
SON – DRC
Reel of 3000
TPS54160QDRCRQ1
5416Q
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
ABSOLUTE MAXIMUM RATINGS (1)
over operating temperature range (unless otherwise noted)
VIN
Input voltage
VIN
–0.3 V to 65 V
EN (2)
–0.3 V to 5 V
BOOT
73 V
VSENSE
–0.3 V to 3 V
COMP
–0.3 V to 3 V
PWRGD
–0.3 V to 6 V
–0.3 V to 3 V
SS/TR
–0.3 V to 3.6 V
RT/CLK
BOOT to PH
8V
–0.6 V to 65 V
VOUT
Output voltage
PH
200 ns
–1 V to 65 V
30 ns
–2 V to 65 V
Maximum dc voltage, TJ = -40°C
VDIFF
Differential voltage
ISOURCE
Source current
±200 mV
PAD to GND
EN
100 μA
BOOT
100 mA
10 μA
VSENSE
PH
Current Limit
100 μA
RT/CLK
VIN
ISINK
ESD
Sink current
Electrostatic discharge protection
-0.85 V
Current Limit
100 μA
COMP
PWRGD
10 mA
SS/TR
200 μA
Human-Body Model (HBM) (AEC-Q100-002)
500 V
Machine Model (MM) (AEC-Q100-003)
Charged-Device Model (CDM) (AEC-Q100-011)
50 V
1000 V
TJ
Operating junction temperature range
–40°C to 150°C
TSTG
Storage temperature range
–65°C to 150°C
(1)
(2)
2
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
See Enable and Adjusting Undervoltage Lockout for details.
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
THERMAL INFORMATION
TPS54160-Q1
THERMAL METRIC (1) (2)
θJA
Junction-to-ambient thermal resistance (standard board)
(3)
DGQ
DRC
10 PINS
10 PINS
62.5
56.5
θJA
Junction-to-ambient thermal resistance (custom board)
57
61.5
θJCtop
Junction-to-case (top) thermal resistance
83
52.1
θJB
Junction-to-board thermal resistance
28
20.6
ψJT
Junction-to-top characterization parameter
1.7
0.9
ψJB
Junction-to-board characterization parameter
20.1
20.8
θJCbot
Junction-to-case (bottom) thermal resistance
21
5.2
(1)
(2)
(3)
UNITS
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Power rating at a specific ambient temperature TA should be determined with a junction temperature of 150°C. This is the point where
distortion starts to substantially increase. See power dissipation estimate in application section of this data sheet for more information.
Test boards conditions:
(a) 3 inches x 3 inches, 2 layers, thickness: 0.062 inch
(b) 2 oz. copper traces located on the top of the PCB
(c) 2 oz. copper ground plane, bottom layer
(d) 6 thermal vias (13mil) located under the device package
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
3
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
PACKAGE DISSIPATION RATINGS (1)
θJA, THERMAL IMPEDANCE, JUNCTION TO
AMBIENT
PACKAGE
(1)
DGQ (MSOP)
57°C/W
DRC (SON)
56.5°C/W
Test board conditions:
A. 3 inch × 3 inch, two layers, 0.062-inch thickness
B. 2-ounce copper traces located on the top and bottom of the PCB
C. Six (13-mil diameter) thermal vias located under the device package
ELECTRICAL CHARACTERISTICS
TJ = –40°C to 150°C, VIN = 3.5 V to 60 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY VOLTAGE (VIN PIN)
Operating input voltage
3.5
60
Internal undervoltage lockout
threshold
No voltage hysteresis, rising and falling
2.5
Shutdown supply current
EN = 0 V, 25°C, 3.5 V ≤ VIN ≤ 60 V
1.3
4
Operating nonswitching supply
current
VSENSE = 0.83 V, VIN = 12 V, TJ = 25°C
116
136
1.25
1.55
V
V
μA
ENABLE AND UVLO (EN PIN)
Enable threshold voltage
Input current
No voltage hysteresis, rising and falling,
TJ = 25°C
0.9
Enable threshold +50 mV
–3.8
Enable threshold –50 mV
–0.9
μA
–2.9
Hysteresis current
V
μA
VOLTAGE REFERENCE
Voltage reference
TJ = 25°C
0.792
0.8
0.808
0.784
0.8
0.816
V
HIGH-SIDE MOSFET
On-resistance
VIN = 3.5 V, BOOT-PH = 3 V
300
VIN = 12 V, BOOT-PH = 6 V
200
410
mΩ
ERROR AMPLIFIER
Input current
50
nA
Error amplifier transconductance (gM) –2 μA < ICOMP < 2 μA, VCOMP = 1 V
97
μMhos
Error amplifier transconductance (gM) –2 μA < ICOMP < 2 μA, VCOMP = 1 V,
during slow start
VVSENSE = 0.4 V
26
μMhos
Error amplifier dc gain
VVSENSE = 0.8 V
Error amplifier bandwidth
Error amplifier source/sink
V(COMP) = 1 V, 100-mV overdrive
COMP to switch current
transconductance
10,000
V/V
2700
kHz
±7
μA
6
A/V
CURRENT LIMIT
Current limit threshold
VIN = 12 V, TJ = 25°C
1.8
2.7
A
182
°C
THERMAL SHUTDOWN
Thermal shutdown
4
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
TJ = –40°C to 150°C, VIN = 3.5 V to 60 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
2500
kHz
720
kHz
2200
kHz
TIMING RESISTOR AND EXTERNAL CLOCK (RT/CLK PIN)
fSW
Switching frequency range using RT
mode
VIN = 12 V
100
Switching frequency
VIN = 12 V, RT = 200 kΩ
450
Switching frequency range using
CLK mode
VIN = 12 V
300
Minimum CLK input pulse width
581
40
RT/CLK high threshold
VIN = 12 V
RT/CLK low threshold
VIN = 12 V
RT/CLK falling edge to PH rising
edge delay
Measured at 500 kHz with RT resistor in series
PLL lock in time
Measured at 500 kHz
1.9
0.5
ns
2.2
V
0.7
V
60
ns
100
μs
2
μA
mV
SLOW START AND TRACKING (SS/TR)
Charge current
VSS/TR = 0.4 V
SS/TR-to-VSENSE matching
VSS/TR = 0.4 V
45
SS/TR-to-reference crossover
98% nominal
1.0
V
SS/TR discharge current (overload)
VSENSE = 0 V, V(SS/TR) = 0.4 V
112
μA
SS/TR discharge voltage
VSENSE = 0 V
54
mV
VSENSE falling
92
VSENSE rising
94
VSENSE rising
109
VSENSE falling
107
Hysteresis
VSENSE falling
2
Output high leakage
VSENSE = VREF, V(PWRGD) = 5.5 V,
TJ = 25°C
On resistance
I(PWRGD) = 3 mA, VSENSE < 0.79 V
Minimum VIN for defined output
V(PWRGD) < 0.5 V, II(PWRGD) = 100 μA
POWER GOOD (PWRGD PIN)
VVSENSE
VSENSE threshold
%
10
nA
Ω
50
0.95
1.5
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
V
5
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DEVICE INFORMATION
PIN CONFIGURATION
DRC PACKAGE
(TOP VIEW)
DGQ PACKAGE
(TOP VIEW)
BOOT
VIN
EN
SS/TR
RT/CLK
10
1
2
3
4
Exposed
Thermal
Pad
5
9
8
7
6
PH
GND
COMP
VSENSE
PWRGD
BOOT
VIN
EN
SS/TR
RT/CLK
1
10
2
4
Exposed 9
Thermal 8
Pad
7
5
6
3
PH
GND
COMP
VSENSE
PWRGD
PIN FUNCTIONS
PIN
I/O
DESCRIPTION
NAME
NO.
BOOT
1
O
A bootstrap capacitor is required between BOOT and PH. If the voltage on this capacitor is below the
minimum required by the output device, the output is forced to switch off until the capacitor is refreshed.
COMP
8
O
Error amplifier output, and input to the output switch current comparator. Connect frequency compensation
components to COMP.
EN
3
I
Enable pin, internal pullup current source. Pull below 1.2 V to disable. Float to enable. Adjust the input
undervoltage lockout with two resistors.
GND
9
–
Ground
PH
10
I
The source of the internal high-side power MOSFET.
PWRGD
6
O
Open-drain output, asserts low if output voltage is low due to thermal shutdown, dropout, overvoltage, or EN
shut down.
RT/CLK
5
I
Resistor timing and external clock. An internal amplifier holds this pin at a fixed voltage when using an
external resistor to ground to set the switching frequency. If the pin is pulled above the PLL upper threshold,
a mode change occurs and the pin becomes a synchronization input. The internal amplifier is disabled and
the pin is a high impedance clock input to the internal PLL. If clocking edges stop, the internal amplifier is
re-enabled and the mode returns to a resistor set function.
SS/TR
4
I
Slow-start and tracking. An external capacitor connected to this pin sets the output rise time. Because the
voltage on this pin overrides the internal reference, it can be used for tracking and sequencing.
VIN
2
I
Input supply voltage, 3.5 V to 60 V.
VSENSE
7
I
Inverting node of the transconductance (gm) error amplifier.
Thermal Pad
6
GND pin must be electrically connected to the exposed pad on the printed circuit board for proper operation.
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
FUNCTIONAL BLOCK DIAGRAM
PWRGD
6
EN
3
VIN
2
Shutdown
UO
Thermal
Shutdown
Enable
Comparator
Logic
UVLO
Shutdown
Shutdown
Logic
OV
Enable
Threshold
Boot
Charge
Voltage
Reference
Boot
UVLO
Minimum
Clamp
Pulse
Skip
ERROR
AMPLIFIER
Current
Sense
PWM
Comparator
VSENSE 7
1 BOOT
Logic
And
PWM Latch
SS/TR 4
Shutdown
Slope
Compensation
10 PH
COMP 8
11 POWERPAD
Frequency
Shift
Overload
Recovery
Maximum
Clamp
Oscillator
with PLL
TPS54160 Block Diagram
9 GND
5
RT/CLK
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
7
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
TYPICAL CHARACTERISTICS
VOLTAGE REFERENCE vs JUNCTION TEMPERATURE
0.816
500
VI = 12 V
VI = 12 V
375
BOOT-PH = 3 V
250
BOOT-PH = 6 V
125
0
-50
0.808
Vref - Voltage Reference - V
RDSON - Static Drain-Source On-State Resistance - mW
ON RESISTANCE vs JUNCTION TEMPERATURE
0.800
0.792
0.784
-50
-25
0
25
50
75
100
TJ - Junction Temperature - °C
125
-25
0
150
25
50
75
100
TJ - Junction Temperature - °C
125
150
Figure 1.
Figure 2.
SWITCH CURRENT LIMIT vs JUNCTION TEMPERATURE
SWITCHING FREQUENCY vs JUNCTION TEMPERATURE
3.5
610
VI = 12 V,
RT = 200 kW
VI = 12 V
fs - Switching Frequency - kHz
Switch Current - A
600
3
2.5
590
580
570
560
2
-50
-25
0
25
50
75
100
125
550
-50
150
-25
0
TJ - Junction Temperature - °C
25
50
75
100
TJ - Junction Temperature - °C
Figure 4.
SWITCHING FREQUENCY vs RT/CLK RESISTANCE HIGH
FREQUENCY RANGE
SWITCHING FREQUENCY vs RT/CLK RESISTANCE LOW
FREQUENCY RANGE
1000
VI = 12 V,
TJ = 25°C
VI = 12 V,
TJ = 25°C
2000
fs - Switching Frequency - kHz
fs - Switching Frequency - kHz
150
Figure 3.
2500
1500
1000
500
0
0
25
50
75
100
125
RT/CLK - Resistance - kW
150
175
200
800
600
400
200
0
100
200
Figure 5.
8
125
300
400
500
600
700
RT/CLK - Resistance - kW
800
900
1000
Figure 6.
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
EA TRANSCONDUCTANCE DURING SLOW START vs
JUNCTION TEMPERATURE
EA TRANSCONDUCTANCE vs JUNCTION TEMPERATURE
150
40
VI = 12 V
VI = 12 V
130
gm - mA/V
gm - mA/V
30
110
90
20
70
10
-50
-25
0
25
50
75
100
TJ - Junction Temperature - °C
125
50
-50
150
-25
0
25
50
75
100
125
150
TJ - Junction Temperature - °C
Figure 7.
Figure 8.
EN PIN VOLTAGE vs JUNCTION TEMPERATURE
EN PIN CURRENT vs JUNCTION TEMPERATURE
1.40
-3.25
VI = 12 V,
VI(EN) = Threshold +50 mV
VI = 12 V
-3.5
I(EN) - mA
EN - Threshold - V
1.30
-3.75
1.20
-4
1.10
-50
-25
0
25
50
75
100
125
150
-4.25
-50
0
25
50
75
100
125
150
TJ - Junction Temperature - °C
Figure 9.
Figure 10.
EN PIN CURRENT vs JUNCTION TEMPERATURE
SS/TR CHARGE CURRENT vs JUNCTION TEMPERATURE
-1
-0.8
VI = 12 V,
VI(EN) = Threshold -50 mV
VI = 12 V
-0.85
-1.5
I(SS/TR) - mA
I(EN) - mA
-25
TJ - Junction Temperature - °C
-0.9
-0.95
-1
-50
-2
-2.5
-25
0
25
50
75
100
TJ - Junction Temperature - °C
125
150
-3
-50
-25
Figure 11.
0
25
50
75
100
TJ - Junction Temperature - °C
125
150
Figure 12.
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
9
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
SS/TR DISCHARGE CURRENT vs JUNCTION
TEMPERATURE
SWITCHING FREQUENCY vs VSENSE
120
100
VI = 12 V
VI = 12 V,
TJ = 25°C
80
% of Nominal fsw
II(SS/TR) - mA
115
110
60
40
105
20
100
-50
0
-25
0
25
50
75
100
TJ - Junction Temperature - °C
125
150
0
SHUTDOWN SUPPLY CURRENT vs INPUT VOLTAGE (Vin)
2
TJ = 25°C
I(VIN) - mA
1.5
1
0.5
1
0.5
0
-25
0
25
50
75
100
TJ - Junction Temperature - °C
125
150
0
10
20
30
40
VI - Input Voltage - V
Figure 15.
VIN SUPPLY CURRENT vs JUNCTION TEMPERATURE
60
VIN SUPPLY CURRENT vs INPUT VOLTAGE
140
VI = 12 V,
VI(VSENSE) = 0.83 V
o
TJ = 25 C,
VI(VSENSE) = 0.83 V
130
130
120
120
I(VIN) - mA
I(VIN) - mA
50
Figure 16.
140
110
100
110
100
90
-25
0
25
50
75
100
TJ - Junction Temperature - °C
125
150
0
Figure 17.
10
0.8
SHUTDOWN SUPPLY CURRENT vs JUNCTION
TEMPERATURE
1.5
90
-50
0.6
Figure 14.
VI = 12 V
I(VIN) - mA
0.4
VSENSE - V
Figure 13.
2
0
-50
0.2
20
40
VI - Input Voltage - V
60
Figure 18.
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
PWRGD ON RESISTANCE vs JUNCTION TEMPERATURE
PWRGD THRESHOLD vs JUNCTION TEMPERATURE
115
100
VI = 12 V
PWRGD Threshold - % of Vref
VI = 12 V
RDSON - W
80
60
40
20
VSENSE Rising
110
VSENSE Falling
105
100
VSENSE Rising
95
VSENSE Falling
90
0
-50
-25
0
25
50
75
100
125
85
-50
150
-25
0
150
Figure 20.
BOOT-PH UVLO vs JUNCTION TEMPERATURE
INPUT VOLTAGE (UVLO) vs JUNCTION TEMPERATURE
2.5
3
2.3
2.75
2
1.8
2.50
2.25
1.5
-50
-25
0
25
50
75
100
TJ - Junction Temperature - °C
125
2
-50
150
-25
0
25
50
75
100
TJ - Junction Temperature - °C
Figure 21.
125
150
Figure 22.
SS/TR TO VSENSE OFFSET vs VSENSE
SS/TR TO VSENSE OFFSET vs TEMPERATURE
600
60
V(SS/TR) = 0.2 V
VI = 12 V
VIN = 12 V
TJ = 25°C
500
55
50
400
Offset - mV
Offset Voltage Threshold (mV)
125
Figure 19.
VI(VIN) - V
VI(BOOT-PH) - V
TJ - Junction Temperature - °C
25
50
75
100
TJ - Junction Temperature - °C
300
45
40
200
35
100
30
-50
0
0
200
400
600
Voltage Sense (mV)
-25
800
Figure 23.
0
25
50
75
100
125
150
TJ - Junction Temperature - °C
Figure 24.
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
11
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
OVERVIEW
The TPS54160 device is a 60-V 1.5-A step-down (buck) regulator with an integrated high-side n-channel
MOSFET. To improve performance during line and load transients the device implements a constant frequency,
current mode control which reduces output capacitance and simplifies external frequency compensation design.
The wide switching frequency of 100 kHz to 2500 kHz allows for efficiency and size optimization when selecting
the output filter components. The switching frequency is adjusted using a resistor to ground on the RT/CLK pin.
The device has an internal phase lock loop (PLL) on the RT/CLK pin that is used to synchronize the power
switch turn on to a falling edge of an external system clock.
The TPS54160 has a default start up voltage of approximately 2.5 V. The EN pin has an internal pullup current
source that can be used to adjust the input voltage undervoltage lockout (UVLO) threshold with two external
resistors. In addition, the pullup current provides a default condition. When the EN pin is floating, the device can
operate. The operating current is 116 μA when not switching and under no load. When the device is disabled,
the supply current is 1.3 μA.
The integrated 200-mΩ high-side MOSFET allows for high efficiency power supply designs capable of delivering
1.5-A continuous current to a load. The TPS54160 reduces the external component count by integrating the boot
recharge diode. The bias voltage for the integrated high-side MOSFET is supplied by a capacitor on the BOOT to
PH pin. The boot capacitor voltage is monitored by an UVLO circuit and turns off the high-side MOSFET when
the boot voltage falls below a preset threshold. The TPS54160 can operate at high duty cycles because of the
boot UVLO. The output voltage can be stepped down to as low as the 0.8-V reference.
The TPS54160 has a power good comparator (PWRGD) which asserts when the regulated output voltage is less
than 92% or greater than 109% of the nominal output voltage. The PWRGD pin is an open drain output which
de-asserts when the VSENSE pin voltage is between 94% and 107% of the nominal output voltage allowing the
pin to transition high when a pullup resistor is used.
The TPS54160 minimizes excessive output overvoltage (OV) transients by taking advantage of the OV power
good comparator. When the OV comparator is activated, the high-side MOSFET is turned off and masked from
turning on until the output voltage is lower than 107%.
The SS/TR (slow start/tracking) pin is used to minimize inrush currents or provide power supply sequencing
during power up. A small value capacitor should be coupled to the pin to adjust the slow start time. A resistor
divider can be coupled to the pin for critical power supply sequencing requirements. The SS/TR pin is discharged
before the output powers up. This discharging ensures a repeatable restart after an over-temperature fault,
UVLO fault or a disabled condition.
The TPS54160, also, discharges the slow start capacitor during overload conditions with an overload recovery
circuit. The overload recovery circuit slow starts the output from the fault voltage to the nominal regulation
voltage once a fault condition is removed. A frequency foldback circuit reduces the switching frequency during
startup and overcurrent fault conditions to help control the inductor current.
12
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION
Fixed Frequency PWM Control
The TPS54160 uses an adjustable fixed frequency, peak current mode control. The output voltage is compared
through external resistors on the VSENSE pin to an internal voltage reference by an error amplifier which drives
the COMP pin. An internal oscillator initiates the turn on of the high-side power switch. The error amplifier output
is compared to the high-side power switch current. When the power switch current reaches the level set by the
COMP voltage, the power switch is turned off. The COMP pin voltage increases and decreases as the output
current increases and decreases. The device implements a current limit by clamping the COMP pin voltage to a
maximum level. The Eco-Mode™ is implemented with a minimum clamp on the COMP pin.
Slope Compensation Output Current
The TPS54160 adds a compensating ramp to the switch current signal. This slope compensation prevents
sub-harmonic oscillations. The available peak inductor current remains constant over the full duty cycle range.
Pulse Skip Eco-Mode
The TPS54160 operates in a pulse-skip Eco-mode control scheme at light load currents to improve efficiency by
reducing switching and gate drive losses. The TPS54160 is designed so that if the output voltage is within
regulation and the peak switch current at the end of any switching cycle is below the pulse skipping current
threshold, the device enters Eco-mode control. This current threshold is the current level corresponding to a
nominal COMP voltage or 500 mV.
When in Eco-mode, the COMP pin voltage is clamped at 500 mV and the high-side MOSFET is inhibited. Further
decreases in load current or in output voltage cannot drive the COMP pin below this clamp voltage level.
Because the device is not switching, the output voltage begins to decay. As the voltage control loop
compensates for the falling output voltage, the COMP pin voltage begins to rise. At this time, the high-side
MOSFET is enabled and a switching pulse initiates on the next switching cycle. The peak current is set by the
COMP pin voltage. The output voltage recharges the regulated value (see Figure 25), then the peak switch
current starts to decrease, and eventually falls below the Eco-mode threshold at which time the device again
enters Eco-mode.
For Eco-mode operation, the TPS54160 senses peak current, not average or load current, so the load current
where the device enters Eco-mode is dependent on the output inductor value. For example, the circuit in
Figure 51 enters Eco-mode at about 18 mA of output current. When the load current is low and the output
voltage is within regulation, the device enters a sleep mode and draws only 116 μA input quiescent current. The
internal PLL remains operating when in sleep mode. When operating at light load currents in the pulse skip
mode, the switching transitions occur synchronously with the external clock signal.
VOUT(ac)
IL
PH
Figure 25. Pulse Skip Mode Operation
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
13
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
Low Dropout Operation and Bootstrap Voltage (BOOT)
The TPS54160 has an integrated boot regulator, and requires a small ceramic capacitor between the BOOT and
PH pins to provide the gate drive voltage for the high-side MOSFET. The BOOT capacitor is refreshed when the
high-side MOSFET is off and the low side diode conducts. The value of this ceramic capacitor should be 0.1 μF.
A ceramic capacitor with an X7R or X5R grade dielectric with a voltage rating of 10 V or higher is recommended
because of the stable characteristics overtemperature and voltage.
To improve drop out, the TPS54160 is designed to operate at 100% duty cycle as long as the BOOT to PH pin
voltage is greater than 2.1 V. When the voltage from BOOT to PH drops below 2.1 V, the high-side MOSFET is
turned off using an UVLO circuit which allows the low side diode to conduct and refresh the charge on the BOOT
capacitor. Because the supply current sourced from the BOOT capacitor is low, the high-side MOSFET can
remain on for more switching cycles than are required to refresh the capacitor, thus the effective duty cycle of the
switching regulator is high.
The effective duty cycle during dropout of the regulator is mainly influenced by the voltage drops across the
power MOSFET, inductor resistance, low side diode and printed circuit board resistance. During operating
conditions in which the input voltage drops and the regulator is operating in continuous conduction mode, the
high-side MOSFET can remain on for 100% of the duty cycle to maintain output regulation, until the BOOT to PH
voltage falls below 2.1 V.
Attention must be taken in maximum duty cycle applications which experience extended time periods with light
loads or no load. When the voltage across the BOOT capacitor falls below the 2.1-V UVLO threshold, the
high-side MOSFET is turned off, but there may not be enough inductor current to pull the PH pin down to
recharge the BOOT capacitor. The high-side MOSFET of the regulator stops switching because the voltage
across the BOOT capacitor is less than 2.1 V. The output capacitor then decays until the difference in the input
voltage and output voltage is greater than 2.1 V, at which point the BOOT UVLO threshold is exceeded, and the
device starts switching again until the desired output voltage is reached. This operating condition persists until
the input voltage and/or the load current increases. It is recommended to adjust the VIN stop voltage greater
than the BOOT UVLO trigger condition at the minimum load of the application using the adjustable VIN UVLO
feature with resistors on the EN pin.
The start and stop voltages for typical 3.3-V and 5-V output applications are shown in Figure 26 and Figure 27.
The voltages are plotted versus load current. The start voltage is defined as the input voltage needed to regulate
the output within 1%. The stop voltage is defined as the input voltage at which the output drops by 5% or stops
switching.
During high duty cycle conditions, the inductor current ripple increases while the BOOT capacitor is being
recharged resulting in an increase in ripple voltage on the output. This is due to the recharge time of the boot
capacitor being longer than the typical high-side off time when switching occurs every cycle.
4
5.6
VO = 3.3 V
VO = 5 V
5.4
VI - Input Voltage - V
VI - Input Voltage - V
3.8
3.6
Start
3.4
Stop
3.2
Start
5
Stop
4.8
3
4.6
0
0.05
0.10
IO - Output Current - A
0.15
Figure 26. 3.3-V Start/Stop Voltage
14
5.2
0.20
0
0.05
0.10
IO - Output Current - A
0.15
0.20
Figure 27. 5-V Start/Stop Voltage
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
Error Amplifier
The TPS54160 has a transconductance amplifier for the error amplifier. The error amplifier compares the
VSENSE voltage to the lower of the SS/TR pin voltage or the internal 0.8-V voltage reference. The
transconductance (gm) of the error amplifier is 97 μA/V during normal operation. During the slow start operation,
the transconductance is a fraction of the normal operating gm. When the voltage of the VSENSE pin is below 0.8
V and the device is regulating using the SS/TR voltage, the gm is 25 μA/V.
The frequency compensation components (capacitor, series resistor and capacitor) are added to the COMP pin
to ground.
Voltage Reference
The voltage reference system produces a precise ±2% voltage reference over temperature by scaling the output
of a temperature stable bandgap circuit.
Adjusting the Output Voltage
The output voltage is set with a resistor divider from the output node to the VSENSE pin. It is recommended to
use 1% tolerance or better divider resistors. Start with a 10 kΩ for the R2 resistor and use the Equation 1 to
calculate R1. To improve efficiency at light loads consider using larger value resistors. If the values are too high,
the regulator is more susceptible to noise, and voltage errors from the VSENSE input current are noticeable
R1 = R2 ?
VOUT - 0.8 V
0.8 V
(1)
Enable and Adjusting Undervoltage Lockout
The TPS54160 is disabled when the VIN pin voltage falls below 2.5 V. If an application requires a higher
undervoltage lockout (UVLO), use the EN pin as shown in Figure 28 to adjust the input voltage UVLO by using
the two external resistors. Though it is not necessary to use the UVLO adjust registers, for operation it is highly
recommended to provide consistent power up behavior. The EN pin has an internal pullup current source, I1, of
0.9 μA that provides the default condition of the TPS54160 operating when the EN pin floats. Once the EN pin
voltage exceeds 1.25 V, an additional 2.9 μA of hysteresis, Ihys, is added. This additional current facilitates input
voltage hysteresis. Use Equation 2 to set the external hysteresis for the input voltage. Use Equation 3 to set the
input start voltage.
TPS54160
VIN
IHYS
I1
0.9 mA
R1
2.9 mA
+
R2
EN
1.25 V
-
Figure 28. Adjustable Undervoltage Lockout (UVLO)
V
- VSTOP
R1 = START
IHYS
R2 =
(2)
VENA
VSTART - VENA
+ I1
R1
(3)
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
15
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
Another technique to add input voltage hysteresis is shown in Figure 29. This method may be used, if the
resistance values are high from the previous method and a wider voltage hysteresis is needed. The resistor R3
sources additional hysteresis current into the EN pin.
TPS54160
VIN
Ihys
R1
I1
0.9 mA
2.9 mA
+
EN
R2
1.25 V
-
VOUT
R3
Figure 29. Adding Additional Hysteresis
R1 =
R2 =
VSTART - VSTOP
V
IHYS + OUT
R3
(4)
VENA
VSTART - VENA
V
+ I1 - ENA
R1
R3
(5)
Do not place a low-impedance voltage source with greater than 5 V directly on the EN pin. Do not place a
capacitor directly on the EN pin if VEN > 5 V when using a voltage divider to adjust the start and stop voltage.
The node voltage, (see Figure 30) must remain equal to or less than 5.8 V. The zener diode can sink up to 100
μA. The EN pin voltage can be greater than 5 V if the VIN voltage source has a high impedance and does not
source more than 100 μA into the EN pin.
VIN
IA
RUVLO1
EN
10 kW
Node
3
IB
RUVLO2
IC
5.8 V
UDG-10065
Figure 30. Node Voltage
16
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
Slow Start/Tracking Pin (SS/TR)
The TPS54160 effectively uses the lower voltage of the internal voltage reference or the SS/TR pin voltage as
the power-supply's reference voltage and regulates the output accordingly. A capacitor on the SS/TR pin to
ground implements a slow start time. The TPS54160 has an internal pullup current source of 2 μA that charges
the external slow start capacitor. The calculations for the slow start time (10% to 90%) are shown in Equation 6.
The voltage reference (VREF) is 0.8 V and the slow start current (ISS) is 2 μA. The slow start capacitor should
remain lower than 0.47 μF and greater than 0.47 nF.
T (ms) ? ISS (mA)
CSS (nF) = SS
VREF (V) ? 0.8
(6)
At power up, the TPS54160 does not start switching until the slow start pin is discharged to less than 40 mV to
ensure a proper power up, see Figure 31.
Also, during normal operation, the TPS54160 stops switching and the SS/TR must be discharged to 40 mV when
the VIN UVLO is exceeded, EN pin pulled below 1.25 V, or a thermal shutdown event occurs.
The VSENSE voltage follows the SS/TR pin voltage with a 45-mV offset up to 85% of the internal voltage
reference. When the SS/TR voltage is greater than 85% on the internal reference voltage the offset increases as
the effective system reference transitions from the SS/TR voltage to the internal voltage reference (see
Figure 23). The SS/TR voltage ramps linearly until clamped at 1.7 V.
EN
SS/TR
VSENSE
VOUT
Figure 31. Operation of SS/TR Pin when Starting
Overload Recovery Circuit
The TPS54160 has an overload recovery (OLR) circuit. The OLR circuit slow starts the output from the overload
voltage to the nominal regulation voltage once the fault condition is removed. The OLR circuit discharges the
SS/TR pin to a voltage slightly greater than the VSENSE pin voltage using an internal pulldown of 100 μA when
the error amplifier is changed to a high voltage from a fault condition. When the fault condition is removed, the
output slow starts from the fault voltage to nominal output voltage.
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
17
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
Sequencing
Many of the common power supply sequencing methods can be implemented using the SS/TR, EN, and
PWRGD pins. The sequential method can be implemented using an open drain output of a power-on reset pin of
another device. The sequential method is illustrated in Figure 32 using two TPS54160 devices. The power good
is coupled to the EN pin on the TPS54160, which enables the second power supply once the primary supply
reaches regulation. If needed, a 1-nF ceramic capacitor on the EN pin of the second power supply provide a
1-ms start-up delay. Figure 33 shows the results of Figure 32.
TPS54160
EN
PWRGD
EN
EN1
SS /TR
SS /TR
PWRGD1
PWRGD
VOUT1
VOUT2
Figure 32. Schematic for Sequential Startup
Sequence
18
Figure 33. Sequential Startup Using EN and
PWRGD
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
TPS54160
3
EN
4
SS/TR
EN1, EN2
VOUT1
VOUT2
6
PWRGD
TPS54160
3
EN
4
SS/TR
6
PWRGD
Figure 34. Schematic for Ratiometric Start-Up
using Coupled SS/TR Pins
Figure 35. Ratiometric Startup Using Coupled
SS/TR Pins
Figure 34 shows a method for ratiometric start-up sequence by connecting the SS/TR pins together. The
regulator outputs ramp up and reach regulation at the same time. When calculating the slow start time, the pullup
current source must be doubled in Equation 6. Figure 35 shows the results of Figure 34.
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
19
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
TPS54160
EN
VOUT 1
SS/TR
PWRGD
TPS54160
VOUT 2
EN
R1
SS/ TR
R2
PWRGD
R3
R4
Figure 36. Schematic for Ratiometric and Simultaneous Start-Up Sequence
Ratiometric and simultaneous power supply sequencing can be implemented by connecting the resistor network
of R1 and R2 shown in Figure 36 to the output of the power supply that needs to be tracked or another voltage
reference source. Using Equation 7 and Equation 8, the tracking resistors can be calculated to initiate the Vout2
slightly before, after or at the same time as Vout1. Equation 9 is the voltage difference between Vout1 and Vout2
at the 95% of nominal output regulation.
The deltaV variable is zero volts for simultaneous sequencing. To minimize the effect of the inherent SS/TR to
VSENSE offset (Vssoffset) in the slow start circuit and the offset created by the pullup current source (Iss) and
tracking resistors, the Vssoffset and Iss are included as variables in the equations.
To design a ratiometric start up in which the Vout2 voltage is slightly greater than the Vout1 voltage when Vout2
reaches regulation, use a negative number in Equation 7 through Equation 9 for deltaV. Equation 9 results in a
positive number for applications in which Vout2 is slightly lower than Vout1 when Vout2 regulation is achieved.
Because the SS/TR pin must be pulled below 40 mV before starting after an EN, UVLO, or thermal shutdown
fault, careful selection of the tracking resistors is needed to ensure device restart after a fault. Make sure the
calculated R1 value from Equation 7 is greater than the value calculated in Equation 10 to ensure the device can
recover from a fault.
As the SS/TR voltage becomes more than 85% of the nominal reference voltage the Vssoffset becomes larger
as the slow start circuits gradually handoff the regulation reference to the internal voltage reference. The SS/TR
pin voltage needs to be greater than 1.3 V for a complete handoff to the internal voltage reference as shown in
Figure 23.
VSSOFFSET
VOUT2 + DV
?
R1 =
ISS
VREF
(7)
R2 =
VREF ? R1
VOUT2 + DV - VREF
(8)
DV = VOUT1 - VOUT2
(9)
R1 > 2800 ? VOUT1 - 180 ? DV
20
(10)
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
EN
EN
VOUT1
VOUT1
VOUT2
Figure 37. Ratiometric Startup with VOUT2 Leading
VOUT1
VOUT2
Figure 38. Ratiometric Startup with VOUT1 Leading
VOUT2
EN
VOUT1
VOUT2
Figure 39. Simultaneous Startup With Tracking Resistor
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
21
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
Constant Switching Frequency and Timing Resistor (RT/CLK Pin)
The switching frequency of the TPS54160 is adjustable over a wide range from approximately 100 kHz to 2500
kHz by placing a resistor on the RT/CLK pin. The RT/CLK pin voltage is typically 0.5 V and must have a resistor
to ground to set the switching frequency. To determine the timing resistance for a given switching frequency, use
Equation 11 or the curves in Figure 40 or Figure 41. To reduce the solution size one would typically set the
switching frequency as high as possible, but tradeoffs of the supply efficiency, maximum input voltage and
minimum controllable on time should be considered.
The minimum controllable on time is typically 130 ns and limits the maximum operating input voltage.
The maximum switching frequency is also limited by the frequency shift circuit. More discussion on the details of
the maximum switching frequency is located below.
206033
RT (kW) =
fSW (kHz)1.0888
(11)
SWITCHING FREQUENCY
vs
RT/CLK RESISTANCE HIGH FREQUENCY RANGE
SWITCHING FREQUENCY
vs
RT/CLK RESISTANCE LOW FREQUENCY RANGE
2500
500
2000
fs - Switching Frequency - kHz
fs - Switching Frequency - kHz
VI = 12 V,
TJ = 25°C
1500
1000
500
0
0
25
50
75
100
125
150
RT/CLK - Clock Resistance - kW
175
200
Figure 40. High Range RT
VI = 12 V,
TJ = 25°C
400
300
200
100
0
200
300
400
500
600 700
800
900
RT/CLK - Resistance - kW
1000 1100
1200
Figure 41. Low Range RT
Overcurrent Protection and Frequency Shift
The TPS54160 implements current mode control, which uses the COMP pin voltage to turn off the high-side
MOSFET on a cycle by cycle basis. Each cycle the switch current and COMP pin voltage are compared, when
the peak switch current intersects the COMP voltage, the high-side switch is turned off. During overcurrent
conditions that pull the output voltage low, the error amplifier responds by driving the COMP pin high, increasing
the switch current. The error amplifier output is clamped internally, which functions as a switch current limit.
To increase the maximum operating switching frequency at high input voltages the TPS54160 implements a
frequency shift. The switching frequency is divided by 8, 4, 2, and 1 as the voltage ramps from 0 V to 0.8 V on
the VSENSE pin.
The device implements a digital frequency shift to enable synchronizing to an external clock during normal
startup and fault conditions. Because the device can divide the switching frequency only by 8, there is a
maximum input voltage limit at which the device operates and can maintain frequency shift protection.
During short-circuit events (particularly with high input voltage applications), the control loop has a finite minimum
controllable on time and the output has a low voltage. During the switch-on time, the inductor current ramps to
the peak current limit because of the high input voltage and minimum on time. During the switch-off time, the
inductor would normally not have enough off time and output voltage for the inductor to ramp down by the ramp
up amount. The frequency shift effectively increases the off time, allowing the current to ramp down.
22
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
Selecting the Switching Frequency
The switching frequency that is selected should be the lower value of the two equations, Equation 12 and
Equation 13. Equation 12 is the maximum switching frequency limitation set by the minimum controllable on time.
Setting the switching frequency above this value causes the regulator to skip switching pulses.
Equation 13 is the maximum switching frequency limit set by the frequency shift protection. To have adequate
output short circuit protection at high input voltages, the switching frequency should be set to be less than the
fsw(maxshift) frequency. In Equation 13, to calculate the maximum switching frequency one must take into account
that the output voltage decreases from the nominal voltage to 0 volts, the fdiv integer increases from 1 to 8
corresponding to the frequency shift.
In Figure 42, the solid line illustrates a typical safe operating area regarding frequency shift and assumes the
output voltage is zero volts, and the resistance of the inductor is 0.1 Ω, FET on resistance of 0.2 Ω, and the
diode voltage drop is 0.5 V. The dashed line is the maximum switching frequency to avoid pulse skipping. Enter
these equations in a spreadsheet or other software or use the SwitcherPro design software to determine the
switching frequency.
fSW (max skip ) =
fSWshift =
fDIV
tON
1
tON
æ I ´R + V
dc
OUT + Vd
´ç L
ç VIN - IL ´ RDS(on ) + Vd
è
æ IL ´ Rdc + VOUT(sc ) + Vd
´ç
ç VIN - IL ´ RDS(on ) + Vd
è
ö
÷
÷
ø
(12)
ö
÷
÷
ø
IL
inductor current
Rdc
inductor resistance
VIN
maximum input voltage
VOUT
output voltage
VOUTSC
output voltage during short
Vd
diode voltage drop
RDS(on)
switch on resistance
tON
controllable on time
ƒDIV
frequency divide equals (1, 2, 4, or 8)
(13)
2500
fs - Switching Frequency - kHz
VO = 3.3 V
2000
Shift
1500
Skip
1000
500
0
10
20
30
40
VI - Input Voltage - V
50
60
Figure 42. Maximum Switching Frequency vs Input Voltage
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
23
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
How to Interface to RT/CLK Pin
The RT/CLK pin can be used to synchronize the regulator to an external system clock. To implement the
synchronization feature connect a square wave to the RT/CLK pin through the circuit network shown in
Figure 43. The square wave amplitude must transition lower than 0.5 V and higher than 2.2 V on the RT/CLK pin
and have an on time greater than 40 ns and an off time greater than 40 ns. The synchronization frequency range
is 300 kHz to 2200 kHz. The rising edge of the PH is synchronized to the falling edge of RT/CLK pin signal. The
external synchronization circuit should be designed in such a way that the device has the default frequency set
resistor connected from the RT/CLK pin to ground should the synchronization signal turn off. It is recommended
to use a frequency set resistor connected as shown in Figure 43 through a 50Ω resistor to ground. The resistor
should set the switching frequency close to the external CLK frequency. It is recommended to ac couple the
synchronization signal through a 10-pF ceramic capacitor to RT/CLK pin and a 4-kΩ series resistor. The series
resistor reduces PH jitter in heavy load applications when synchronizing to an external clock and in applications
which transition from synchronizing to RT mode. The first time the CLK is pulled above the CLK threshold the
device switches from the RT resistor frequency to PLL mode. The internal 0.5-V voltage source is removed and
the CLK pin becomes high impedance as the PLL starts to lock onto the external signal. Because there is a PLL
on the regulator the switching frequency can be higher or lower than the frequency set with the external resistor.
The device transitions from the resistor mode to the PLL mode and then increases or decreases the switching
frequency until the PLL locks onto the CLK frequency within 100 μs.
When the device transitions from the PLL to resistor mode the switching frequency slows down from the CLK
frequency to 150 kHz, then reapply the 0.5-V voltage and the resistor then sets the switching frequency. The
switching frequency is divided by 8, 4, 2, and 1 as the voltage ramps from 0 V to 0.8 V on VSENSE pin. The
device implements a digital frequency shift to enable synchronizing to an external clock during normal startup
and fault conditions. Figure 44, Figure 45 and Figure 46 show the device synchronized to an external system
clock in continuous conduction mode (ccm) discontinuous conduction (dcm) and pulse skip mode (psm).
TPS54160
10 pF
4 kW
PLL
Rfset
EXT
Clock
Source
50 W
RT/CLK
Figure 43. Synchronizing to a System Clock
24
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
EXT
EXT
VOUT
IL
PH
PH
IL
Figure 44. Plot of Synchronizing in ccm
Figure 45. Plot of Synchronizing in dcm
EXT
IL
PH
Figure 46. Plot of Synchronizing in PSM
Power Good (PWRGD Pin)
The PWRGD pin is an open drain output. Once the VSENSE pin is between 94% and 107% of the internal
voltage reference the PWRGD pin is de-asserted and the pin floats. It is recommended to use a pullup resistor
between the values of 10 and 100kΩ to a voltage source that is 5.5 V or less. The PWRGD is in a defined state
once the VIN input voltage is greater than 1.5 V but with reduced current sinking capability. PWRGD achieves
full current sinking capability as VIN input voltage approaches 3 V.
The PWRGD pin is pulled low when the VSENSE is lower than 92% or greater than 109% of the nominal internal
reference voltage. Also, PWRGD is pulled low if the UVLO or thermal shutdown are asserted or EN is pulled low.
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
25
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
Overvoltage Transient Protection
The TPS54160 incorporates an overvoltage transient protection (OVTP) circuit to minimize voltage overshoot
when recovering from output fault conditions or strong unload transients on power supply designs with low value
output capacitance. For example, when the power supply output is overloaded the error amplifier compares the
actual output voltage to the internal reference voltage. If the VSENSE pin voltage is lower than the internal
reference voltage for a considerable time, the output of the error amplifier responds by clamping the error
amplifier output to a high voltage. Thus, requesting the maximum output current. Once the condition is removed,
the regulator output rises and the error amplifier output transitions to the steady state duty cycle. In some
applications, the power supply output voltage can respond faster than the error amplifier output can respond, this
actuality leads to the possibility of an output overshoot. The OVTP feature minimizes the output overshoot, when
using a low value output capacitor, by implementing a circuit to compare the VSENSE pin voltage to OVTP
threshold which is 109% of the internal voltage reference. If the VSENSE pin voltage is greater than the OVTP
threshold, the high-side MOSFET is disabled preventing current from flowing to the output and minimizing output
overshoot. When the VSENSE voltage drops lower than the OVTP threshold, the high-side MOSFET is allowed
to turn on at the next clock cycle.
Thermal Shutdown
The device implements an internal thermal shutdown to protect itself if the junction temperature exceeds 182°C.
The thermal shutdown forces the device to stop switching when the junction temperature exceeds the thermal
trip threshold. Once the die temperature decreases below 182°C, the device reinitiates the power up sequence
by discharging the SS/TR pin.
Small Signal Model for Loop Response
Figure 47 shows an equivalent model for the TPS54160 control loop which can be modeled in a circuit simulation
program to check frequency response and dynamic load response. The error amplifier is a transconductance
amplifier with a gmEA of 97 μA/V. The error amplifier can be modeled using an ideal voltage controlled current
source. The resistor Ro and capacitor Co model the open loop gain and frequency response of the amplifier. The
1-mV ac voltage source between the nodes a and b effectively breaks the control loop for the frequency
response measurements. Plotting c/a shows the small signal response of the frequency compensation. Plotting
a/b shows the small signal response of the overall loop. The dynamic loop response can be checked by
replacing RL with a current source with the appropriate load step amplitude and step rate in a time domain
analysis. This equivalent model is only valid for continuous conduction mode designs.
PH
VO
Power Stage
gmps 6 A/V
a
b
R1
RESR
RL
COMP
c
0.8 V
CO
R3
C2
RO
VSENSE
gmea
97 mA/V
C1
COUT
R2
Figure 47. Small Signal Model for Loop Response
26
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
Simple Small Signal Model for Peak Current Mode Control
Figure 48 describes a simple small signal model that can be used to understand how to design the frequency
compensation. The TPS54160 power stage can be approximated to a voltage-controlled current source (duty
cycle modulator) supplying current to the output capacitor and load resistor. The control to output transfer
function is shown in Equation 14 and consists of a dc gain, one dominant pole, and one ESR zero. The quotient
of the change in switch current and the change in COMP pin voltage (node c in Figure 47) is the power stage
transconductance. The gmPS for the TPS54160 is 6A/V. The low-frequency gain of the power stage frequency
response is the product of the transconductance and the load resistance as shown in Equation 15.
As the load current increases and decreases, the low-frequency gain decreases and increases, respectively. This
variation with the load may seem problematic at first glance, but fortunately the dominant pole moves with the
load current (see Equation 16). The combined effect is highlighted by the dashed line in the right half of
Figure 48. As the load current decreases, the gain increases and the pole frequency lowers, keeping the 0-dB
crossover frequency the same for the varying load conditions which makes it easier to design the frequency
compensation. The type of output capacitor chosen determines whether the ESR zero has a profound effect on
the frequency compensation design. Using high ESR aluminum electrolytic capacitors may reduce the number
frequency compensation components needed to stabilize the overall loop because the phase margin increases
from the ESR zero at the lower frequencies (see Equation 17).
VO
Adc
VC
RESR
fp
RL
gmps
COUT
fz
Figure 48. Simple Small Signal Model and Frequency Response for Peak Current Mode Control
æ
s ö
ç1 +
÷
2p ´ fZ ø
VOUT
= Adc ´ è
VC
æ
s ö
ç1 +
÷
2
p
´ fP ø
è
(14)
Adc = gmps ´ RL
(15)
1
fP =
COUT ´ RL ´ 2p
(16)
1
fZ =
COUT ? RESR ? 2p
(17)
Small Signal Model for Frequency Compensation
The TPS54160 uses a transconductance amplifier for the error amplifier and readily supports three of the
commonly-used frequency compensation circuits. Compensation circuits Type 2A, Type 2B, and Type 1 are
shown in Figure 49. Type 2 circuits most likely implemented in high bandwidth power-supply designs using low
ESR output capacitors. The Type 1 circuit is used with power-supply designs with high-ESR aluminum
electrolytic or tantalum capacitors.. Equation 18 and Equation 19 show how to relate the frequency response of
the amplifier to the small signal model in Figure 49. The open-loop gain and bandwidth are modeled using the RO
and CO shown in Figure 49. See the application section for a design example using a Type 2A network with a
low ESR output capacitor.
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
27
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
Equation 18 through Equation 27 are provided as a reference for those who prefer to compensate using the
preferred methods. Those who prefer to use prescribed method use the method outlined in the application
section or use switched information.
VO
R1
VSENSE
gmea
Type 2A
COMP
Type 2B
Type 1
Vref
R2
RO
R3
CO
C2
C1
R3
C2
C1
Figure 49. Types of Frequency Compensation
Aol
A0
P1
Z1
P2
A1
BW
Figure 50. Frequency Response of the Type 2A and Type 2B Frequency Compensation
Ro =
COUT
Aol(V/V)
gmea
gmea
=
2p ´ BW (Hz)
(18)
(19)
æ
ö
s
ç1 +
÷
2p ´ fZ1 ø
è
EA = A0 ´
æ
ö æ
ö
s
s
ç1 +
÷ ´ ç1 +
÷
2p ´ fP1 ø è
2p ´ fP2 ø
è
R2
R1 + R2
R2
´ Ro| | R3 ´
R1 + R2
A0 = gmea ´ Ro ´
A1 = gmea
28
(20)
(21)
(22)
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
DETAILED DESCRIPTION (continued)
P1 =
Z1 =
1
2p ´ Ro ´ C1
(23)
1
2p ´ R3 ´ C1
(24)
1
P2 =
type 2a
2p ´ R3 | | R ´ (C2 + COUT )
(25)
1
type 2b
2p ´ R3 | | R ´ COUT
(26)
P2 =
1
P2 =
type 1
2p ´ R ´ (C2 + COUT )
(27)
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
29
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
APPLICATION INFORMATION
Design Guide — Step-By-Step Design Procedure
This example details the design of a high frequency switching regulator design using ceramic output capacitors.
A few parameters must be known to start the design process. These parameters are typically determined at the
system level. For this example, start with the following known parameters:
Output voltage
3.3 V
Transient response 0 to 1.5-A load step
ΔVout = 4%
Maximum output current
1.5 A
Input voltage
12 V (nom), 8 V to 18 V
Output voltage ripple
< 33 mVpp
Start input voltage (rising VIN)
7.25 V
Stop input voltage (falling VIN)
6.25 V
Selecting the Switching Frequency
The first step is to decide on a switching frequency for the regulator. Typically, the user wants to choose the
highest switching frequency possible, because this produces the smallest solution size. The high switching
frequency allows for lower valued inductors and smaller output capacitors compared to a power supply that
switches at a lower frequency. The switching frequency that can be selected is limited by the minimum on-time of
the internal power switch, the input voltage and the output voltage and the frequency shift limitation.
Equation 12 and Equation 13 must be used to find the maximum switching frequency for the regulator, choose
the lower value of the two equations. Switching frequencies higher than these values result in pulse skipping or
the lack of overcurrent protection during a short circuit.
The typical minimum on time (tonmin) is 130 ns for the TPS54160. For this example, the output voltage is 3.3 V
and the maximum input voltage is 18 V, which allows for a maximum switch frequency up to 1600 kHz when
including the inductor resistance, on resistance and diode voltage in Equation 12. To ensure overcurrent
runaway is not a concern during short circuits in your design use Equation 13 or the solid curve in Figure 42 to
determine the maximum switching frequency. With a maximum input voltage of 20 V, for some margin above
18 V, assuming a diode voltage of 0.5 V, inductor resistance of 100 mΩ, switch resistance of 200 mΩ, a current
limit value of 2.7 A, the maximum switching frequency is approximately 2500 kHz.
Choosing the lower of the two values and adding some margin a switching frequency of 1200 kHz is used. To
determine the timing resistance for a given switching frequency, use Equation 11 or the curve in Figure 40.
The switching frequency is set by resistor Rt shown in Figure 51.
L1
10 mH
0.1 mF
C1
U1
TPS54160DGQ
BOOT
VIN
C2
C3
C4
2.2 mF 2.2 mF 0.1 mF
R3
EN
SS/TR
RT/CLK
332 kW
CSS
RT
0.01 mF
90.9 kW
R4
61.9 kW
COMP
VSNS
PWRGD
CF
6.8 pF
COUT
+
47 mF/6.3 V
PH
GND
PwPd
8 - 18 V
D1
B220A
3.3 V at 1.5 A
RC
76.8 kW
CC
2700 pF
R1
31.6 kW
R2
10 kW
Figure 51. High Frequency, 3.3V Output Power Supply Design with Adjusted UVLO.
30
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
Output Inductor Selection (LO)
To calculate the minimum value of the output inductor, use Equation 28.
KIND is a coefficient that represents the amount of inductor ripple current relative to the maximum output current.
The inductor ripple current is filtered by the output capacitor. Therefore, choosing high inductor ripple currents
impacts the selection of the output capacitor, because the output capacitor must have a ripple current rating
equal to or greater than the inductor ripple current. In general, the inductor ripple value is at the discretion of the
designer; however, the following guidelines may be used.
For designs using low ESR output capacitors such as ceramics, a value as high as KIND = 0.3 may be used.
When using higher ESR output capacitors, KIND = 0.2 yields better results. Because the inductor ripple current is
part of the PWM control system, the inductor ripple current should always be greater than 100 mA for
dependable operation. In a wide input voltage regulator, it is best to choose an inductor ripple current on the
larger side. This allows the inductor to still have a measurable ripple current with the input voltage at its
minimum.
For this design example, use KIND = 0.2 and the minimum inductor value is calculated to be 7.6 μH. For this
design, a nearest standard value was chosen: 10 μH. For the output filter inductor, it is important that the RMS
current and saturation current ratings not be exceeded. The RMS and peak inductor current can be found from
Equation 30 and Equation 31.
For this design, the RMS inductor current is 1.506 A and the peak inductor current is 1.62 A. The chosen
inductor is a MSS6132-103. It has a saturation current rating of 1.64 A and an RMS current rating of 1.9 A.
As the equation set demonstrates, lower ripple currents reduce the output voltage ripple of the regulator but
require a larger value of inductance. Selecting higher ripple currents increases the output voltage ripple of the
regulator but allows for a lower inductance value.
The current flowing through the inductor is the inductor ripple current plus the output current. During power up,
faults or transient load conditions, the inductor current can increase above the calculated peak inductor current
level calculated above. In transient conditions, the inductor current can increase up to the switch current limit of
the device. For this reason, the most conservative approach is to specify an inductor with a saturation current
rating equal to or greater than the switch current limit rather than the peak inductor current.
Vinmax - Vout
Vout
Lo min =
´
Io ´ KIND
Vinmax ´ ƒsw
(28)
IRIPPLE £ IO ´ KIND
IL(rms) =
2
(IO )
(29)
1 æ VOUT ´ (Vinmax - VOUT ) ö
+
´ç
÷
÷
12 çè
Vinmax ´ LO ´ fSW
ø
2
(30)
I
ILPeak = IOUT + RIPPLE
2
(31)
Output Capacitor
There are three primary considerations for selecting the value of the output capacitor. The output capacitor
determines the modulator pole, the output voltage ripple, and how the regulators responds to a large change in
load current. The output capacitance needs to be selected based on the more stringent of these three criteria.
The desired response to a large change in the load current is the first criteria. The output capacitor needs to
supply the load with current when the regulator cannot. This situation would occur if there are desired hold-up
times for the regulator where the output capacitor must hold the output voltage above a certain level for a
specified amount of time after the input power is removed. The regulator also temporarily is not able to supply
sufficient output current if there is a large fast increase in the current needs of the load such as transitioning from
no load to a full load. The regulator usually needs two or more clock cycles for the control loop to see the change
in load current and output voltage and adjust the duty cycle to react to the change. The output capacitor must be
sized to supply the extra current to the load until the control loop responds to the load change. The output
capacitance must be large enough to supply the difference in current for two clock cycles while only allowing a
tolerable amount of droop in the output voltage. Equation 32 shows the minimum output capacitance necessary
to accomplish this.
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
31
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
Where ΔIout is the change in output current, ƒsw is the regulators switching frequency and ΔVout is the allowable
change in the output voltage. For this example, the transient load response is specified as a 4% change in Vout
for a load step from 0 A (no load) to 1.5 A (full load). For this example, ΔIout = 1.5 – 0 = 1.5 A and
ΔVout = 0.04 × 3.3 = 0.132 V. Using these numbers gives a minimum capacitance of 18.9 μF. This value does not
take the ESR of the output capacitor into account in the output voltage change. For ceramic capacitors, the ESR
is usually small enough to ignore in this calculation. Aluminum electrolytic and tantalum capacitors have higher
ESR that should be taken into account.
The catch diode of the regulator cannot sink current, so any stored energy in the inductor produces an output
voltage overshoot when the load current rapidly decreases (see Figure 52). The output capacitor must be sized
to absorb energy stored in the inductor when transitioning from a high load current to a lower load current. The
excess energy that is stored in the output capacitor increases the voltage on the capacitor. The capacitor must
be sized to maintain the desired output voltage during these transient periods. Equation 33 is used to calculate
the minimum capacitance to keep the output voltage overshoot to a desired value. Where L is the value of the
inductor, IOH is the output current under heavy load, IOL is the output under light load, VF is the final peak output
voltage, and Vi is the initial capacitor voltage. For this example, the worst-case load step us from 1.5 A to 0 A.
The output voltage increases during this load transition, and the stated maximum in our specification is 4% of the
output voltage. This makes Vf = 1.04 × 3.3 = 3.432. Vi is the initial capacitor voltage, which is the nominal output
voltage of 3.3 V. Using these numbers in Equation 33 yields a minimum capacitance of 25.3 μF.
Equation 34 calculates the minimum output capacitance needed to meet the output voltage ripple specification.
Where fsw is the switching frequency, Voripple is the maximum allowable output voltage ripple, and Iripple is the
inductor ripple current. Equation 35 yields 0.7 μF.
Equation 35 calculates the maximum ESR an output capacitor can have to meet the output voltage ripple
specification. Equation 35 indicates the ESR should be less than 147 mΩ.
The most stringent criteria for the output capacitor is 25.3 μF of capacitance to keep the output voltage in
regulation during an unload transient.
Additional capacitance de-ratings for aging, temperature, and dc bias should be factored in, which increases this
minimum value. For this example, a 47-μF 6.3-V X7R ceramic capacitor with 5-mΩ ESR is used.
Capacitors generally have limits to the amount of ripple current they can handle without failing or producing
excess heat. An output capacitor that can support the inductor ripple current must be specified. Some capacitor
data sheets specify the Root Mean Square (RMS) value of the maximum ripple current. Equation 36 can be used
to calculate the RMS ripple current the output capacitor needs to support. For this application, Equation 36 yields
64.8 mA.
2 ´ DIOUT
COUT =
fSW ´ DVOUT
(32)
((I ) - (I ) )
´
((V ) - (V ) )
2
OH
COUT > LO
2
f
COUT
32
2
OL
2
i
(33)
1
1
>
´
8 ´ fSW æ VOUT(ripple ) ö
ç
÷
ç IRIPPLE ÷
è
ø
(34)
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
VOUT(ripple )
RESR =
IRIPPLE
ICOUT(rms) =
(35)
(
VOUT ´ VIN(max ) - VOUT
)
12 ´ VIN(max ) ´ LO ´ fSW
(36)
Catch Diode
The TPS54160 requires an external catch diode between the PH pin and GND. The selected diode must have a
reverse voltage rating equal to or greater than Vinmax. The peak current rating of the diode must be greater than
the maximum inductor current. The diode should also have a low forward voltage. Schottky diodes are typically a
good choice for the catch diode due to their low forward voltage. The lower the forward voltage of the diode, the
higher the efficiency of the regulator.
Typically, the higher the voltage and current ratings the diode has, the higher the forward voltage. Because the
design example has an input voltage up to 18 V, a diode with a minimum of 20-V reverse voltage is selected.
For the example design, the B220A Schottky diode is selected for its lower forward voltage, and it comes in a
larger package size, which has good thermal characteristics over small devices. The typical forward voltage of
the B220A is 0.50 V.
The diode must also be selected with an appropriate power rating. The diode conducts the output current during
the off-time of the internal power switch. The off-time of the internal switch is a function of the maximum input
voltage, the output voltage, and the switching frequency. The output current during the off-time is multiplied by
the forward voltage of the diode which equals the conduction losses of the diode. At higher switch frequencies,
the ac losses of the diode need to be taken into account. The ac losses of the diode are due to the charging and
discharging of the junction capacitance and reverse recovery. Equation 37 is used to calculate the total power
dissipation, conduction losses plus ac losses, of the diode.
The B220A has a junction capacitance of 120 pF. Using Equation 37, the selected diode dissipates 0.632 W.
This power dissipation, depending on mounting techniques, should produce a 16°C temperature rise in the diode
when the input voltage is 18 V and the load current is 1.5 A.
If the power supply spends a significant amount of time at light load currents or in sleep mode consider using a
diode which has a low leakage current and slightly higher forward voltage drop.
PD
(V
=
IN(max ) - VOUT
)´ I
OUT
2
´ Vfd
VIN(max )
+
C j ´ fSW ´ (VIN + Vfd)
2
(37)
Input Capacitor
The TPS54160 requires a high-quality ceramic, type X5R or X7R, input decoupling capacitor of at least 3-μF
effective capacitance and, in some applications, a bulk capacitance. The effective capacitance includes any dc
bias effects. The voltage rating of the input capacitor must be greater than the maximum input voltage. The
capacitor must also have a ripple current rating greater than the maximum input current ripple of the TPS54160.
The input ripple current can be calculated using Equation 38.
The value of a ceramic capacitor varies significantly over temperature and the amount of dc bias applied to the
capacitor. The capacitance variations due to temperature can be minimized by selecting a dielectric material that
is stable over temperature. X5R and X7R ceramic dielectrics are usually selected for power regulator capacitors
because they have a high capacitance to volume ratio and are fairly stable over temperature. The output
capacitor must also be selected with the dc bias taken into account. The capacitance value of a capacitor
decreases as the dc bias across a capacitor increases.
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
33
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
For this example design, a ceramic capacitor with at least a 20-V voltage rating is required to support the
maximum input voltage. Common standard ceramic capacitor voltage ratings include 4 V, 6.3 V, 10 V, 16 V,
25 V, 50 V or 100 V, so a 25-V capacitor should be selected. For this example, two 2.2-μF 25-V capacitors in
parallel have been selected. Table 1 shows a selection of high voltage capacitors. The input capacitance value
determines the input ripple voltage of the regulator. The input voltage ripple can be calculated using Equation 39.
Using the design example values, Ioutmax = 1.5 A, Cin = 4.4 μF, ƒsw = 1200 kHz, yields an input voltage ripple of
71 mV and a rms input ripple current of 0.701 A.
Icirms = Iout ´
Vout
´
Vin min
(Vin min
- Vout )
Vin min
(38)
Iout max ´ 0.25
ΔVin =
Cin ´ ¦ sw
(39)
Table 1. Capacitor Types
VENDOR
VALUE (μF)
1.0 to 2.2
1.0 to 4.7
Murata
1.0
1.0 to 2.2
1.0 10 1.8
1.0 to 1.2
Vishay
1.0 to 3.9
1.0 to 1.8
1.0 to 2.2
TDK
1.5 to 6.8
1.0. to 2.2
1.0 to 3.3
1.0 to 4.7
AVX
1.0
1.0 to 4.7
1.0 to 2.2
EIA SIZE
1210
1206
2220
2225
1812
1210
1210
1812
VOLTAGE
DIELECTRIC
100 V
COMMENTS
GRM32 series
50 V
100 V
GRM31 series
50 V
50 V
100 V
VJ X7R series
50 V
100 V
100 V
50 V
100 V
50 V
X7R
C series C4532
C series C3225
50 V
100 V
50 V
X7R dielectric series
100 V
Slow Start Capacitor
The slow start capacitor determines the minimum amount of time required for the output voltage to reach its
nominal programmed value during power up. This is useful if a load requires a controlled voltage slew rate. This
is also used if the output capacitance is large and would require large amounts of current to quickly charge the
capacitor to the output voltage level. The large currents necessary to charge the capacitor may make the
TPS54160 reach the current limit or excessive current draw from the input power supply may cause the input
voltage rail to sag. Limiting the output voltage slew rate solves both of these problems.
The slow start time must be long enough to allow the regulator to charge the output capacitor up to the output
voltage without drawing excessive current. Equation 40 can be used to find the minimum slow start time, tss,
necessary to charge the output capacitor, Cout, from 10% to 90% of the output voltage, Vout, with an average
slow start current of Issavg. In the example, to charge the 47-μF output capacitor up to 3.3 V while only allowing
the average input current to be 0.125 A requires a 1-ms slow start time.
Once the slow start time is known, the slow start capacitor value can be calculated using Equation 6. For the
example circuit, the slow start time is not too critical, because the output capacitor value is 47μF which does not
require much current to charge to 3.3V. The example circuit has the slow start time set to an arbitrary value of
1ms which requires a 3.3 nF capacitor.
C
? VOUT ? 0.8
TSS > OUT
ISSAVG
(40)
34
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
Bootstrap Capacitor Selection
A 0.1-μF ceramic capacitor must be connected between the BOOT and PH pins for proper operation. It is
recommended to use a ceramic capacitor with X5R or better grade dielectric. The capacitor should have a 10-V
or higher voltage rating.
Undervoltage Lockout (UVLO) Set Point
The UVLO can be adjusted using an external voltage divider on the EN pin of the TPS54160. The UVLO has two
thresholds, one for power up when the input voltage is rising and one for power down or brown outs when the
input voltage is falling. For the example design, the supply should turn on and start switching once the input
voltage increases above 7.25 V (enabled). After the regulator starts switching, it should continue to do so until
the input voltage falls below 6.25 V (UVLO stop).
The programmable UVLO and enable voltages are set using a resistor divider between Vin and ground to the EN
pin. Equation 2 through Equation 3 can be used to calculate the resistance values necessary. For the example
application, a 332 kΩ between Vin and EN and a 61.9 kΩ between EN and ground are required to produce the
7.25 V and 6.25 V start and stop voltages.
Output Voltage and Feedback Resistors Selection
For the example design, 10.0 kΩ was selected for R2. Using Equation 1, R1 is calculated as 31.25 kΩ. The
nearest standard 1% resistor is 31.6 kΩ. Due to current leakage of the VSENSE pin, the current flowing through
the feedback network should be greater than 1 μA to maintain the output voltage accuracy. This requirement
makes the maximum value of R2 equal to 800 kΩ. Choosing higher resistor values decreases quiescent current
and improves efficiency at low output currents but may introduce noise immunity problems.
Compensation
There are several industry techniques used to compensate DC/DC regulators. The method presented here yields
high phase margins. For most conditions, the regulator will have a phase margin between 60 and 90 degrees.
The method presented here ignores the effects of the slope compensation that is internal to the TPS54160.
Since the slope compensation is ignored, the actual crossover frequency is usually lower than the crossover
frequency used in the calculations.
Use SwitcherPro software for a more accurate design.
The uncompensated regulator will have a dominant pole, typically located between 300 Hz and 3 kHz, due to the
output capacitor and load resistance and a pole due to the error amplifier. One zero exists due to the output
capacitor and the ESR. The zero frequency is higher than either of the two poles.
If left uncompensated, the double pole created by the error amplifier and the modulator would lead to an unstable
regulator. To stabilize the regulator, one pole must be canceled out. One design approach is to locate a
compensating zero at the modulator pole. Then select a crossover frequency that is higher than the modulator
pole. The gain of the error amplifier can be calculated to achieve the desired crossover frequency. The capacitor
used to create the compensation zero along with the output impedance of the error amplifier form a low
frequency pole to provide a minus one slope through the crossover frequency. Then a compensating pole is
added to cancel the zero due to the output capacitors ESR. If the ESR zero resides at a frequency higher than
the switching frequency then it can be ignored.
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
35
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
To compensate the TPS54160 using this method, first calculate the modulator pole and zero using the following
equations:
IOUT(max )
fP(mod) >
2 ´ p ´ VOUT ´ COUT
where
•
•
•
IOUT(max) is the maximum output current
COUT is the output capacitance
VOUT is the nominal output voltage
fZ(mod) >
(41)
1
2 ´ p ´ RESR ´ COUT
(42)
For the example design, the modulator pole is located at 1.5 kHz and the ESR zero is located at 338 kHz.
Next, the designer selects a crossover frequency which will determine the bandwidth of the control loop. The
crossover frequency must be located at a frequency at least five times higher than the modulator pole. The
crossover frequency must also be selected so that the available gain of the error amplifier at the crossover
frequency is high enough to allow for proper compensation.
Equation 47 is used to calculate the maximum crossover frequency when the ESR zero is located at a frequency
that is higher than the desired crossover frequency. This will usually be the case for ceramic or low ESR
tantalum capacitors. Aluminum Electrolytic and Tantalum capacitors will typically produce a modulator zero at a
low frequency due to their high ESR.
The example application is using a low ESR ceramic capacitor with 10mΩ of ESR making the zero at 338 kHz.
This value is much higher than typical crossover frequencies so the maximum crossover frequency is calculated
using both Equation 43 and Equation 46.
Using Equation 46 gives a minimum crossover frequency of 7.6 kHz and Equation 43 gives a maximum
crossover frequency of 45.3 kHz.
A crossover frequency of 45 kHz is arbitrarily selected from this range.
For ceramic capacitors use Equation 43:
fC(max ) £ 2100
fP(mod)
VOUT
(43)
For tantalum or aluminum capacitors use Equation 44:
51442
fC(max ) £
VOUT
For all cases use Equation 45 and Equation 46:
f
fC(max ) £ SW
5
fC(min ) ³ 5 ´ fP(mod)
(44)
(45)
(46)
Once a crossover frequency, fC, has been selected, the gain of the modulator at the crossover frequency is
calculated. The gain of the modulator at the crossover frequency is calculated using Equation 47 .
gm(PS ) ´ RLOAD ´ (2p ´ fC ´ COUT ´ RESR + 1)
GMOD(fc ) =
2p ´ fC ´ COUT ´ (RLOAD ´ RESR ) + 1
(47)
36
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
For the example problem, the gain of the modulator at the crossover frequency is 0.542. Next, the compensation
components are calculated. A resistor in series with a capacitor is used to create a compensating zero. A
capacitor in parallel to these two components forms the compensating pole. However, calculating the values of
these components varies depending on if the ESR zero is located above or below the crossover frequency. For
ceramic or low ESR tantalum output capacitors, the zero will usually be located above the crossover frequency.
For aluminum electrolytic and tantalum capacitors, the modulator zero is usually located lower in frequency than
the crossover frequency. For cases where the modulator zero is higher than the crossover frequency (ceramic
capacitors).
VOUT
RC =
GMOD(fc ) ´ gm(EA ) ´ VREF
(48)
1
CC =
p ´ RC ´ fP(mod)
(49)
´ RESR
C
Cf = OUT
RC
(50)
For cases where the modulator zero is less than the crossover frequency (Aluminum or Tantalum capacitors), the
equations are:
VOUT
RC =
GMOD(fc ) ´ fZ(mod) ´ gm(EA ) ´ VREF
(51)
1
CC =
p ´ RC ´ fP(mod)
Cf =
(52)
1
2 ´ p ´ RC ´ fZ(mod)
(53)
For the example problem, the ESR zero is located at a higher frequency compared to the crossover frequency so
Equation 50 through Equation 53 are used to calculate the compensation components. In this example, the
calculated components values are:
• RC= 76.2 kΩ
• CC= 2710 pF
• Cf =6.17 pF
The calculated value of the Cf capacitor is not a standard value so a value of 2700 pF is used. 6.8 pF is used for
CC. The RC resistor sets the gain of the error amplifier which determines the crossover frequency. The calculated
RC resistor is not a standard value, so 76.8 kΩ is used.
APPLICATION CURVES
VIN
VO
VOUT
EN
IO
IL
Figure 52. Load Transmit
Figure 53. Startup With EN
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
37
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
VOUT
VOUT
IL
PH
VIN
IL
Figure 54. VIN Power Up
Figure 55. Output Ripple CCM
VOUT
VOUT
IL
IL
PH
Figure 56. Output Ripple, DCM
PH
Figure 57. Output Ripple, PSM
VIN
VIN
IL
IL
PH
PH
Figure 58. Input Ripple CCM
38
Figure 59. Input Ripple DCM
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
95
VO = 3.3 V,
fsw = 1200 kHz
VI = 8 V
90
85
VIN
Efficiency - %
80
IL
VI = 12 V
VI = 16 V
75
70
65
PH
60
55
50
0
Figure 60. Input Ripple PSM
0.25
0.50
0.75
1
1.25
IL - Load Current - A
1.5
1.75
2
Figure 61. Efficiency vs Load Current
1.015
60
150
VI = 12 V
1.010
40
100
1.005
Phase - o
Gain - dB
50
20
0
Gain
0
-50
Regulation (%)
Phase
1.000
0.995
-100
-20
0.990
-150
-40
100
1-103
1-104
f - Frequency - Hz
1-105
0.985
0.00
1-106
0.25
0.50
0.75
1.00
1.25
1.50
1.75
2.00
Load Current - A
Figure 62. Overall Loop Frequency Response
Figure 63. Regulation vs Load Current
1.015
IO = 0.5 A
1.010
Regulation (%)
1.005
1.000
0.995
0.990
0.985
5
10
15
20
VI - Input Voltage - V
Figure 64. Regulation vs Input Voltage
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
39
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
Power Dissipation
The following formulas show how to estimate power dissipation under continuous conduction mode (CCM)
operation. These equations should not be used if the device is working in discontinuous conduction mode (DCM).
The power dissipation of the device includes conduction loss (Pcon), switching loss (Psw), gate drive loss (Pgd),
and supply current loss (Pq).
2
Pcon = IO × RDS(on) × (VOUT / VIN)
2
(54)
–9
PSW = VIN × fSW × IO × 0.25×10 sec/V
(55)
–9
Pgd = VIN × 3×10 Asec × fSW
(56)
Pq = 116µA × VIN
(57)
Where:
IOUT is the output current (A).
RDS(on) is the on-resistance of the high-side MOSFET (Ω).
VOUT is the output voltage (V).
VIN is the input voltage (V).
fsw is the switching frequency (Hz).
So
Ptot = Pcon + PSW + Pgd + Pq
(58)
For given TA,
TJ = TA + qJA × Ptot
(59)
For given TJ(MAX) = 150°C
TA(MAX) = TJ(MAX) – qJA × Ptot
(60)
Where:
Ptot is the total device power dissipation (W).
TA is the ambient temperature (°C).
TJ is the junction temperature (°C).
θJA is the thermal resistance of the package (°C/W).
TJ(MAX) is maximum junction temperature (°C).
TA(MAX) is maximum ambient temperature (°C).
There are additional power losses in the regulator circuit due to the inductor ac and dc losses, the catch diode,
and trace resistance that impact the overall efficiency of the regulator.
40
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
Layout
Layout is a critical portion of good power supply design. There are several signals paths that conduct fast
changing currents or voltages that can interact with stray inductance or parasitic capacitance to generate noise
or degrade the power supplies performance. To help eliminate these problems, the VIN pin should be bypassed
to ground with a low ESR ceramic bypass capacitor with X5R or X7R dielectric. Care should be taken to
minimize the loop area formed by the bypass capacitor connections, the VIN pin, and the anode of the catch
diode. See Figure 65 for a PCB layout example. The GND pin should be tied directly to the power pad under the
IC and the power pad.
The power pad should be connected to any internal PCB ground planes using multiple vias directly under the IC.
The PH pin should be routed to the cathode of the catch diode and to the output inductor. Because the PH
connection is the switching node, the catch diode and output inductor should be located close to the PH pins,
and the area of the PCB conductor minimized to prevent excessive capacitive coupling. For operation at full rated
load, the top side ground area must provide adequate heat dissipating area. The RT/CLK pin is sensitive to noise
so the RT resistor should be located as close as possible to the IC and routed with minimal lengths of trace. The
additional external components can be placed approximately as shown. It may be possible to obtain acceptable
performance with alternate PCB layouts, however this layout has been shown to produce good results and is
meant as a guideline.
Vout
Output
Capacitor
Topside
Ground
Area
Route Boot Capacitor
Trace on another layer to
provide wide path for
topside ground
Input
Bypass
Capacitor
BOOT
Vin
UVLO
Adjust
Resistors
Slow Start
Capacitor
Output
Inductor
Catch
Diode
PH
VIN
GND
EN
COMP
SS/TR
VSENSE
RT/CLK
PWRGD
Frequency
Set Resistor
Compensation
Network
Resistor
Divider
Thermal VIA
Signal VIA
Figure 65. PCB Layout Example
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
41
TPS54160-Q1
SLVS922E – JULY 2009 – REVISED MARCH 2011
www.ti.com
Figure 66. Wide Input Voltage Design
42
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS54160-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
3-Mar-2011
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
TPS54160QDGQRQ1
ACTIVE
MSOPPowerPAD
DGQ
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
TPS54160QDRCRQ1
ACTIVE
SON
DRC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS54160-Q1 :
• Catalog: TPS54160
NOTE: Qualified Version Definitions:
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
3-Mar-2011
• Catalog - TI's standard catalog product
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Mar-2011
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TPS54160QDGQRQ1
MSOPPower
PAD
DGQ
10
2500
330.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
TPS54160QDRCRQ1
SON
DRC
10
3000
330.0
12.4
3.3
3.3
1.0
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Mar-2011
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS54160QDGQRQ1
MSOP-PowerPAD
DGQ
10
2500
370.0
355.0
55.0
TPS54160QDRCRQ1
SON
DRC
10
3000
370.0
355.0
55.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Wireless
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions
www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated