Series AMEL5-AZ Preliminary 5 Watt | AC-DC Converter FEATURES: • • • • Models Single output Model I/O Isolation 3000VAC Operating Temp: -40 oC to +80 oC Input: 90-305VAC, 47-440Hz, or 120-430VDC Over load, Over Voltage, Short Circuit Protection Input Voltage (VAC/Hz) Input Voltage (VDC) Temperature range (ºC) 90-305/47-440 90-305/47-440 90-305/47-440 90-305/47-440 90-305/47-440 120-430 120-430 120-430 120-430 120-430 -40 to +80 -40 to +80 -40 to +80 -40 to +80 -40 to +80 AMEL5-3.3SAZ AMEL5-5SAZ AMEL5-12SAZ AMEL5-15SAZ AMEL5-24SAZ Input Specifications Parameters Current (full load) Inrush current <2ms (cold start) Leakage current External fuse Input Dissipation Output Specifications Parameters Voltage accuracy Line regulation Load regulation Transient Recovery Time Transient Response Deviation Minimum load Ripple & Noise Output Voltage (V) Parameters Tested I/O voltage Isolation Resistance www.aimtec.com F 052e R8 RoHS compliant Energy Star compliant Efficiency up to 74% Soft start Output Current max (A) 3.3 5 12 15 24 1. 5 1 0.42 0.333 0.21 Maximum capacitive Load (µF) 2200 1100 680 330 220 Conditions Typical slow blow type No Load 1.5 <0.5 Conditions Typical Maximum 20MHz bandwidth ±2 ±0.5 ±0.5 200 ±2 0 100 Conditions Typical Rated 115 VAC 230 VAC 115 VAC 230 VAC 0-100% load 25% load step *Ripple and Noise are measured at 20MHz bandwidth by using a 0.1µF (M/C) parallel capacitor. Isolation Specifications • • • • 3sec >1000 Tel: +1 514 620 2722 1 of 3 Maximum 120 70 10 20 0.2 3000 Efficiency (%) 66 69 72 72 74 Units mA mA A A mA A W Units % % % µs % of Vout % mV p-p Units VAC MΩ Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEL5-AZ Preliminary General Specifications Parameters 5 Watt | AC-DC Converter Conditions Typical Maximum Units Switching frequency 66 KHz Over Load protection Auto recovery, Fold back >116% Over voltage protection Zener diode clamp Short circuit protection Auto recovery o Operating temperature With derating above 50ºC Refer to the models table above C o Storage temperature -40 to +95 C o Maximum Case temperature 100 C Temperature coefficient 0.02 % / oC Humidity Non condensing 20 ~ 95 % RH Case material Plastic resin + Fiberglass (flammability to UL 94V-0) Weight 30 g Dimensions (L x W x H) 2.03 x 1.10 x 0.70 inches 51.5 x 28 x 17.8mm MTBF > 400 000 hrs (MIL-HDBK -217F, t=+25oC) NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Environment Approval Parameters Shock Vibrations Conditions Wave form: Half sine wave Acceleration amplitude: 5gn Bump duration: 30 ms Number of bumps: 18 (3 in each direction for every axis) Converter operation before and after test, body mounted (on chassis) Test mode: Sweep sine 10-100Hz, speed 0.05Hz/s Displacement: 1mm Acceleration: 3g 3 loops 30min one cycle, 3h total, every axis tested Converter operation before and after test, body mounted (on chassis) Safety Specifications Parameters Agency approvals Standards cULus, CE, CB pending Medical Electrical Equipment Information technology Equipment EMI - Conducted and radiated emission Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity Electrical Fast Transient/Burst Immunity Surge Immunity RF, Conducted Disturbance Immunity Power frequency Magnetic Field Immunity Voltage dips, Short Interruptions Immunity IEC\EN\UL 60950-1 EN 60950-1:2006+A11:2009 EN55022, class B IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 IEC 61000-4-5 IEC 61000-4-6 IEC 61000-4-8 IEC 61000-4-11 Pin Out Specifications www.aimtec.com F 052e R8 Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEL5-AZ Preliminary Pin 5 Watt | AC-DC Converter Single 1 2 3 4 5 AC Input (N) AC Input (L) +V Output -V Output No pin Dimensions 2.03 (51.50) 1.80 (45.72) 1 1.10 0.80 (28.00) (20.32) 3 TOP VIEW 2 4 1 0.40 (10.16) 3 TOP VIEW 0.40 (10.16) 2 5 4 5 0.11 (2.89) 17.80 (0.70) 5 Ø- 0.047 (Ø 1.2) Ø 0.04 (1.00) 0.2 (5.08) (Min) DIV: 0.2 (5.08) Dimensions: inch (mm) Case Tolerance:± 0.012 (0.30) Pin Pitch Tolerance: ± 0.012 (0.30) NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 052e R8 Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only