MICROCHIP TC4426_13

TC4426/TC4427/TC4428
1.5A Dual High-Speed Power MOSFET Drivers
Features:
General Description:
• High Peak Output Current – 1.5A
• Wide Input Supply Voltage Operating Range:
- 4.5V to 18V
• High Capacitive Load Drive Capability – 1000 pF
in 25 ns (typ.)
• Short Delay Times – 40 ns (typ.)
• Matched Rise and Fall Times
• Low Supply Current:
- With Logic ‘1’ Input – 4 mA
- With Logic ‘0’ Input – 400 A
• Low Output Impedance – 7
• Latch-Up Protected: Will Withstand 0.5A Reverse
Current
• Input Will Withstand Negative Inputs Up to 5V
• ESD Protected – 4 kV
• Pin-compatible with the TC426/TC427/TC428
• Space-saving 8-Pin MSOP and 8-Pin 6x5 DFN
Packages
The TC4426/TC4427/TC4428 are improved versions
of the earlier TC426/TC427/TC428 family of MOSFET
drivers. The TC4426/TC4427/TC4428 devices have
matched rise and fall times when charging and
discharging the gate of a MOSFET.
These devices are highly latch-up resistant under any
conditions within their power and voltage ratings. They
are not subject to damage when up to 5V of noise spiking (of either polarity) occurs on the ground pin. They
can accept, without damage or logic upset, up to
500 mA of reverse current (of either polarity) being
forced back into their outputs. All terminals are fully
protected against Electrostatic Discharge (ESD) up to
4 kV.
The TC4426/TC4427/TC4428 MOSFET drivers can
easily charge/discharge 1000 pF gate capacitances in
under 30 ns. These devices provide low enough
impedances in both the on and off states to ensure the
MOSFET’s intended state will not be affected, even by
large transients.
Other compatible drivers are the TC4426A/TC4427A/
TC4428A family of devices. The TC4426A/TC4427A/
TC4428A devices have matched leading and falling
edge input-to-output delay times, in addition to the
matched rise and fall times of the TC4426/TC4427/
TC4428 devices.
Applications:
• Switch Mode Power Supplies
• Line Drivers
• Pulse Transformer Drive
Package Types
8-Pin MSOP/
PDIP/SOIC TC4426 TC4427 TC4428
NC
IN A
GND
IN B
1
8 NC
2 TC4426 7 OUT A
3 TC4427 6 VDD
4 TC4428 5 OUT B
NC
OUT A
VDD
OUT B
NC
OUT A
VDD
OUT B
8-Pin DFN(1)
NC
1
IN A 2
GND
3
TC4426
TC4427
TC4428
IN B 4
TC4426 TC4427 TC4428
8
NC
NC
NC
7
OUT A
OUT A
OUT A
6
VDD
VDD
VDD
5
OUT B
OUT B
OUT B
Note 1: Exposed pad of the DFN package is electrically isolated.
 2002-2012 Microchip Technology Inc.
DS21422E-page 1
TC4426/TC4427/TC4428
Functional Block Diagram
Inverting
VDD
1.5 mA
300 mV
Output
Non-Inverting
Input
Effective
Input C = 12 pF
(Each Input)
4.7V
TC4426/TC4427/TC4428
GND
Note 1: TC4426 has two inverting drivers, while the TC4427 has two non-inverting
drivers. The TC4428 has one inverting and one non-inverting driver.
2: Ground any unused driver input.
DS21422E-page 2
 2002-2012 Microchip Technology Inc.
TC4426/TC4427/TC4428
1.0
ELECTRICAL
CHARACTERISTICS
PIN FUNCTION TABLE
Name
Absolute Maximum Ratings †
NC
Supply Voltage ..................................................... +22V
Input Voltage, IN A or IN B
..................................... (VDD + 0.3V) to (GND – 5V)
Package Power Dissipation (TA 70°C)
DFN .............................................................. Note 3
MSOP .......................................................... 340 mW
PDIP ............................................................ 730 mW
SOIC............................................................ 470 mW
Function
No Connection
IN A
Input A
GND
Ground
IN B
Input B
OUT B
Output B
VDD
Supply Input
OUT A
Output A
NC
No Connection
Storage Temperature Range.............. -65°C to +150°C
Maximum Junction Temperature ...................... +150°C
† Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. These
are stress ratings only and functional operation of the device
at these or any other conditions above those indicated in the
operation sections of the specifications is not implied.
Exposure to Absolute Maximum Rating conditions for
extended periods may affect device reliability.
DC CHARACTERISTICS
Electrical Specifications: Unless otherwise noted, TA = +25ºC with 4.5V  VDD  18V.
Parameters
Sym
Min
Typ
Max
Units
Conditions
Logic ‘1’, High Input Voltage
VIH
2.4
—
—
V
Logic ‘0’, Low Input Voltage
VIL
—
—
0.8
V
Input Current
IIN
-1.0
—
+1.0
A
VOH
VDD – 0.025
—
—
V
DC Test
Low Output Voltage
VOL
—
—
0.025
V
DC Test
Output Resistance
RO
—
7
10

IOUT = 10 mA, VDD = 18V
Peak Output Current
IPK
—
1.5
—
A
VDD = 18V
Latch-Up Protection
Withstand Reverse Current
IREV
—
> 0.5
—
A
Duty cycle2%, t 300 s
VDD = 18V
Rise Time
tR
—
19
30
ns
Figure 4-1
Fall Time
tF
—
19
30
ns
Figure 4-1
Delay Time
tD1
—
20
30
ns
Figure 4-1
Delay Time
tD2
—
40
50
ns
Figure 4-1
IS
—
—
—
—
4.5
0.4
mA
VIN = 3V (Both inputs)
VIN = 0V (Both inputs)
Input
Note 2
0VVINVDD
Output
High Output Voltage
Switching Time (Note 1)
Power Supply
Power Supply Current
Note 1:
2:
3:
Switching times ensured by design.
For V temperature range devices, the VIH (Min) limit is 2.0V.
Package power dissipation is dependent on the copper pad area on the PCB.
 2002-2012 Microchip Technology Inc.
DS21422E-page 3
TC4426/TC4427/TC4428
DC CHARACTERISTICS (OVER OPERATING TEMPERATURE RANGE)
Electrical Specifications: Unless otherwise noted, over operating temperature range with 4.5V  VDD  18V.
Parameters
Sym
Min
Typ
Max
Units
Conditions
Input
Logic ‘1’, High Input Voltage
VIH
2.4
—
—
V
Logic ‘0’, Low Input Voltage
VIL
—
—
0.8
V
Input Current
IIN
-10
—
+10
A
High Output Voltage
VOH
VDD – 0.025
—
—
V
DC Test
Low Output Voltage
VOL
—
—
0.025
V
DC Test
Note 2
0VVINVDD
Output
Output Resistance
RO
—
9
12

IOUT = 10 mA, VDD = 18V
Peak Output Current
IPK
—
1.5
—
A
VDD = 18V
Latch-Up Protection
Withstand Reverse Current
IREV
—
>0.5
—
A
Duty cycle2%, t 300 s
VDD = 18V
Rise Time
tR
—
—
40
ns
Figure 4-1
Fall Time
tF
—
—
40
ns
Figure 4-1
Delay Time
tD1
—
—
40
ns
Figure 4-1
Delay Time
tD2
—
—
60
ns
Figure 4-1
IS
—
—
—
—
8.0
0.6
mA
VIN = 3V (Both inputs)
VIN = 0V (Both inputs)
Switching Time (Note 1)
Power Supply
Power Supply Current
Note 1:
2:
Switching times ensured by design.
For V temperature range devices, the VIH (Min) limit is 2.0V.
TEMPERATURE CHARACTERISTICS
Electrical Specifications: Unless otherwise noted, all parameters apply with 4.5V  VDD  18V.
Parameters
Sym
Min
Typ
Max
Units
Specified Temperature Range (C)
TA
0
—
+70
°C
Specified Temperature Range (E)
TA
-40
—
+85
°C
Specified Temperature Range (V)
TA
-40
—
+125
°C
Conditions
Temperature Ranges
Maximum Junction Temperature
TJ
—
—
+150
°C
Storage Temperature Range
TA
-65
—
+150
°C
Thermal Resistance, 8L-6x5 DFN
JA
—
33.2
—
°C/W
Thermal Resistance, 8L-MSOP
JA
—
206
—
°C/W
Thermal Resistance, 8L-PDIP
JA
—
125
—
°C/W
Thermal Resistance, 8L-SOIC
JA
—
155
—
°C/W
Package Thermal Resistances
DS21422E-page 4
 2002-2012 Microchip Technology Inc.
TC4426/TC4427/TC4428
2.0
TYPICAL PERFORMANCE CURVES
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Note: Unless otherwise indicated, TA = +25ºC with 4.5V  VDD  18V.
100
100
2200 pF
2200 pF
80
1500 pF
1500 pF
tFALL (nsec)
tRISE (nsec)
80
60
1000 pF
40
60
1000 pF
40
470 pF
470 pF
20
20
100 pF
100 pF
0
0
4
6
FIGURE 2-1:
Voltage.
8
10
14
12
VDD (V)
16
Rise Time vs. Supply
100
4
18
14
16
18
Fall Time vs. Supply
5V
tFALL (nsec)
tRISE (nsec)
12
VDD (V)
80
10V
15V
40
20
60
10V
15V
40
20
0
100
1000
CLOAD (pF)
FIGURE 2-2:
Load.
0
100
10,000
Rise Time vs. Capacitive
Propagation Delay (nsec)
C LOAD = 1000 pF
VDD = 17.5V
40
30
tFALL
20
10
–55 –35 –15
tRISE
85
CLOAD = 1000 pF
VIN = 5V
tD2
tD1
 2002-2012 Microchip Technology Inc.
6
105 125
Rise and Fall Times vs.
10,000
Fall Time vs. Capacitive
80
75
70
65
60
55
50
45
40
35
30
25
20
4
5
25 45 65
Temperature (˚C)
1000
CLOAD (pF)
FIGURE 2-5:
Load.
60
Time (nsec)
10
100
5V
60
FIGURE 2-3:
Temperature.
8
FIGURE 2-4:
Voltage.
80
50
6
8
10
12
14
16
18
VDD (V)
FIGURE 2-6:
Supply Voltage.
Propagation Delay Time vs.
DS21422E-page 5
TC4426/TC4427/TC4428
Note: Unless otherwise indicated, TA = +25ºC with 4.5V  VDD  18V.
45
CLOAD = 1000 pF
55
VDD = 12V
50
45
tD2
40
35
30
tD1
25
CLOAD = 1000 pF
VIN = 5V
VDD = 18V
tD2
40
Delay Time (nsec)
Propagation Delay (nsec)
60
20
35
30
25
20
tD1
15
15
10
10
0
1
2
3
4
5
6
7
8
9
10
11
12
-55
-35
-15
Input Amplitude (V)
FIGURE 2-7:
Input Amplitude.
5
25
45
65
85
105 125
Temperature (ºC)
Propagation Delay Time vs.
FIGURE 2-10:
Temperature.
Propagation Delay Time vs.
4.0
3.5
Both Inputs = 1
IQUIESCENT (mA)
IQUIESCENT (mA)
V DD = 18V
1
3.0
Both Inputs = 1
2.5
Both Inputs = 0
0.1
4
6
8
FIGURE 2-8:
Voltage.
10
12
VDD
14
16
2.0
–55 –35 –15
18
Supply Current vs. Supply
FIGURE 2-11:
Temperature.
5
65
85
105 125
Supply Current vs.
25
25
20
20
Worst Case @ TJ = +150˚C
RDS(ON) (Ω)
Worst Case @ TJ = +150˚C
RDS(ON) (Ω)
25 45
TA (˚C)
15
Typical @ TA = +25˚C
10
15
Typical @ TA = +25˚C
10
5
5
4
6
8
10
12
14
16
18
4
6
VDD
FIGURE 2-9:
Supply Voltage.
DS21422E-page 6
Output Resistance (ROH) vs.
8
10
12
14
16
18
VDD
FIGURE 2-12:
Supply Voltage.
Output Resistance (ROL) vs.
 2002-2012 Microchip Technology Inc.
TC4426/TC4427/TC4428
Note: Unless otherwise indicated, TA = +25ºC with 4.5V  VDD  18V.
60
60
VDD = 18V
2 MHz
VDD = 18V
50
1000 pF
2200 pF
50
ISUPPLY (mA)
ISUPPLY (mA)
900 kHz
40
600 kHz
30
20
200 kHz
10
40
100 pF
30
20
10
20 kHz
0
100
1000
CLOAD (pF)
FIGURE 2-13:
Capacitive Load.
0
10,000
Supply Current vs.
10
FIGURE 2-16:
Frequency.
60
VDD = 12V
50
50
40
40
ISUPPLY (mA)
ISUPPLY (mA)
Supply Current vs.
60
2 MHz
VDD = 12V
30
900 kHz
20
600 kHz
10
1000
CLOAD (pF)
FIGURE 2-14:
Capacitive Load.
2200 pF
1000 pF
30
20
100 pF
10
200 kHz
20 kHz
0
100
0
10
10,000
Supply Current vs.
100
1000
FREQUENCY (kHz)
FIGURE 2-17:
Frequency.
60
Supply Current vs.
60
VDD = 6V
VDD = 6V
50
50
40
30
ISUPPLY (mA)
ISUPPLY (mA)
100
1000
FREQUENCY (kHz)
2 MHz
20
900 kHz
600 kHz
200 kHz
20 kHz
10
0
100
FIGURE 2-15:
Capacitive Load.
1000
CLOAD (pF)
2200 pF
30
1000 pF
20
10
10,000
Supply Current vs.
 2002-2012 Microchip Technology Inc.
40
100 pF
0
10
FIGURE 2-18:
Frequency.
100
1000
FREQUENCY (kHz)
Supply Current vs.
DS21422E-page 7
TC4426/TC4427/TC4428
Note: Unless otherwise indicated, TA = +25ºC with 4.5V  VDD  18V.
–8
10
9
8
7
6
A • sec
5
4
3
2
–9
10
Note:
4
6
8
10
12
VDD
14
16
18
The values on this graph represent the loss
seen by both drivers in a package during one
complete cycle. For a single driver, divide the
stated values by 2. For a single transition of a
single driver, divide the stated value by 4.
FIGURE 2-19:
Supply Voltage.
DS21422E-page 8
Crossover Energy vs.
 2002-2012 Microchip Technology Inc.
TC4426/TC4427/TC4428
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
PIN FUNCTION TABLE (1)
8-Pin PDIP/
MSOP/SOIC
8-Pin
DFN
1
1
NC
No connection
2
2
IN A
Input A
3
3
GND
Ground
4
4
IN B
Input B
5
5
OUT B
6
6
VDD
7
7
OUT A
8
8
NC
No connection
PAD
NC
Exposed Metal Pad
—
Note 1:
3.1
Symbol
Description
Output B
Supply input
Output A
Duplicate pins must be connected for proper operation.
Inputs A and B
MOSFET driver inputs A and B are high-impedance,
TTL/CMOS compatible inputs. These inputs also have
300 mV of hysteresis between the high and low
thresholds that prevents output glitching even when the
rise and fall time of the input signal is very slow.
3.2
Supply Input (VDD)
The VDD input is the bias supply for the MOSFET driver
and is rated for 4.5V to 18V with respect to the ground
pin. The VDD input should be bypassed with local
ceramic capacitors. The value of these capacitors
should be chosen based on the capacitive load that is
being driven. A value of 1.0 F is suggested.
Ground (GND)
Ground is the device return pin. The ground pin(s)
should have a low-impedance connection to the bias
supply source return. High peak currents will flow out
the ground pin(s) when the capacitive load is being
discharged.
3.3
3.4
3.5
Exposed Metal Pad
The exposed metal pad of the 6x5 DFN package is not
internally connected to any potential. Therefore, this
pad can be connected to a ground plane or other
copper plane on a printed circuit board, to aid in heat
removal from the package.
Output A and B
MOSFET driver outputs A and B are low-impedance,
CMOS push-pull style outputs. The pull-down and pullup devices are of equal strength, making the rise and
fall times equivalent.
 2002-2012 Microchip Technology Inc.
DS21422E-page 9
TC4426/TC4427/TC4428
4.0
APPLICATIONS INFORMATION
+5V
90%
Input
VDD = 18V
0V
4.7 F
0.1 F
Input
tD1
7
VDD
tR
90%
90%
Output
5
10%
10%
0V
Inverting Driver
CL = 1000 pF
4
tD2
tF
Output
6
2
10%
+5V
90%
Input
3
Input: 100 kHz,
square wave,
tRISE = tFALL  10 ns
0V
VDD
10%
tD1 90%
tR
Output
0V
10%
90%
tD2
tF
10%
Non-Inverting Driver
FIGURE 4-1:
DS21422E-page 10
Switching Time Test Circuit.
 2002-2012 Microchip Technology Inc.
TC4426/TC4427/TC4428
5.0
PACKAGING INFORMATION
5.1
Package Marking Information
8-Lead DFN
Example:
XXXXXXX
XXXXXXX
XXYYWW
NNN
TC4426
EMF
0420
256
Example:
8-Lead MSOP
4426C
420256
XXXXX
YWWNNN
8-Lead PDIP (300 mil)
XXXXXXXX
XXXXXNNN
YYWW
TC4427
CPA256
0420
8-Lead SOIC (150 mil)
XXXXXXXX
XXXXYYWW
NNN
Legend: XX...X
Y
YY
WW
NNN
e3
*
Note:
Example:
Example:
TC4428
COA0420
256
Customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
 2002-2012 Microchip Technology Inc.
DS21422E-page 11
TC4426/TC4427/TC4428
8-Lead Plastic Dual Flat No Lead Package (MF) 6x5 mm Body (DFN-S) – Saw Singulated
Note:
For the most current package drawings, please see the Microchip Packaging Specification located
at http://www.microchip.com/packaging
DS21422E-page 12
 2002-2012 Microchip Technology Inc.
TC4426/TC4427/TC4428
8-Lead Plastic Micro Small Outline Package (MS) (MSOP)
Note:
For the most current package drawings, please see the Microchip Packaging Specification located
at http://www.microchip.com/packaging
E
E1
p
D
2
B
n
1

c

L
F
A2
A
A1

INCHES
Units
Dimension Limits
MILLIMETERS*
NOM
MIN
MIN
MAX
NOM
MAX
Number of Pins
n
Pitch
p
Overall Height
A
-
-
.043
-
-
1.10
Molded Package Thickness
A2
.030
.033
.037
0.75
0.85
0.95
Standoff
A1
.000
-
.006
0.00
-
0.15
Overall Width
E
.193 BSC
4.90 BSC
Molded Package Width
E1
.118 BSC
3.00 BSC
Overall Length
D
.118 BSC
Foot Length
L
0.60
0.80
Footprint (Reference)
Foot Angle
F

Lead Thickness
c
.003
.006
.009
0.08
Lead Width
B

.009
.012
.016
0.22
Mold Draft Angle Top
Mold Draft Angle Bottom

8
8
.026 BSC
.016
0.65 BSC
3.00 BSC
.024
.031
0.40
.037 REF
0°
0.95 REF
-
8°
0°
-
8°
-
0.23
-
0.40
5°
-
15°
5°
-
15°
5°
-
15°
5°
-
15°
* Controlling Parameter
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
See ASME Y14.5M
REF: Reference Dimension, usually without tolerance, for information purposes only.
See ASME Y14.5M
JEDEC Equivalent: MO-187
Drawing No. C04-111
 2002-2012 Microchip Technology Inc.
Revised 07-21-05
DS21422E-page 13
TC4426/TC4427/TC4428
8-Lead Plastic Dual In-line (P) – 300 mil (PDIP)
Note:
For the most current package drawings, please see the Microchip Packaging Specification located
at http://www.microchip.com/packaging
E1
D
2
n
1

E
A2
A
L
c
A1

B1
p
eB
B
Units
Dimension Limits
n
p
INCHES*
NOM
8
.100
.155
.130
MAX
MILLIMETERS
NOM
8
2.54
3.56
3.94
2.92
3.30
0.38
7.62
7.94
6.10
6.35
9.14
9.46
3.18
3.30
0.20
0.29
1.14
1.46
0.36
0.46
7.87
9.40
5
10
5
10
MAX
Number of Pins
Pitch
Top to Seating Plane
A
.140
.170
4.32
Molded Package Thickness
A2
.115
.145
3.68
Base to Seating Plane
.015
A1
Shoulder to Shoulder Width
E
.300
.313
.325
8.26
Molded Package Width
E1
.240
.250
.260
6.60
Overall Length
D
.360
.373
.385
9.78
Tip to Seating Plane
L
.125
.130
.135
3.43
c
Lead Thickness
.008
.012
.015
0.38
Upper Lead Width
B1
.045
.058
.070
1.78
Lower Lead Width
B
.014
.018
.022
0.56
§
eB
.310
.370
.430
10.92
Overall Row Spacing

Mold Draft Angle Top
5
10
15
15

Mold Draft Angle Bottom
5
10
15
15
* Controlling Parameter
§ Significant Characteristic
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side.
JEDEC Equivalent: MS-001
Drawing No. C04-018
DS21422E-page 14
MIN
MIN
 2002-2012 Microchip Technology Inc.
TC4426/TC4427/TC4428
8-Lead Plastic Small Outline (SN) – Narrow, 150 mil (SOIC)
Note:
For the most current package drawings, please see the Microchip Packaging Specification located
at http://www.microchip.com/packaging
E
E1
p
D
2
B
n
1

h
45
c
A2
A


L
Units
Dimension Limits
n
p
INCHES*
NOM
8
.050
.061
.056
.007
.237
.154
.193
.015
.025
4
.009
.017
12
12
MAX
MILLIMETERS
NOM
8
1.27
1.35
1.55
1.32
1.42
0.10
0.18
5.79
6.02
3.71
3.91
4.80
4.90
0.25
0.38
0.48
0.62
0
4
0.20
0.23
0.33
0.42
0
12
0
12
MAX
Number of Pins
Pitch
Overall Height
A
.053
.069
1.75
Molded Package Thickness
A2
.052
.061
1.55
Standoff
A1
.004
.010
0.25
§
Overall Width
E
.228
.244
6.20
Molded Package Width
E1
.146
.157
3.99
Overall Length
D
.189
.197
5.00
Chamfer Distance
h
.010
.020
0.51
Foot Length
L
.019
.030
0.76

Foot Angle
0
8
8
c
Lead Thickness
.008
.010
0.25
Lead Width
B
.013
.020
0.51

Mold Draft Angle Top
0
15
15

Mold Draft Angle Bottom
0
15
15
* Controlling Parameter
§ Significant Characteristic
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side.
JEDEC Equivalent: MS-012
Drawing No. C04-057
 2002-2012 Microchip Technology Inc.
MIN
A1
MIN
DS21422E-page 15
TC4426/TC4427/TC4428
6.0
REVISION HISTORY
Revision E (December 2012)
Added a note to each package outline drawing.
DS21422E-page 16
 2002-2012 Microchip Technology Inc.
TC4426/TC4427/TC4428
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
Device
X
Temperature
Range
XX
XXX
X
Package
Tape & Reel
PB Free
Examples:
a)
TC4426COA:
1.5A Dual Inverting
MOSFET driver,
0°C to +70°C
SOIC package.
Device:
TC4426:
TC4427:
TC4428:
1.5A Dual MOSFET Driver, Inverting
1.5A Dual MOSFET Driver, Non-Inverting
1.5A Dual MOSFET Driver, Complementary
b)
TC4426EUA:
1.5A Dual Inverting
MOSFET driver,
-40°C to +85°C.
MSOP package.
Temperature Range:
C
E
V
0°C to +70°C (PDIP and SOIC only)
-40°C to +85°C
-40°C to +125°C
c)
TC4426EMF:
1.5A Dual Inverting
MOSFET driver,
-40°C to +85°C,
DFN package.
Package:
MF
= Dual, Flat, No-Lead (6X5 mm Body), 8-lead
MF713 = Dual, Flat, No-Lead (6X5 mm Body), 8-lead
(Tape and Reel)
OA
= Plastic SOIC, (150 mil Body), 8-lead
OA713 = Plastic SOIC, (150 mil Body), 8-lead
(Tape and Reel)
PA
= Plastic DIP (300 mil Body), 8-lead
UA
= Plastic Micro Small Outline (MSOP), 8-lead
UA713 = Plastic Micro Small Outline (MSOP), 8-lead
(Tape and Reel)
a)
TC4427CPA:
1.5A Dual Non-Inverting
MOSFET driver,
0°C to +70°C
PDIP package.
b)
TC4427EPA:
1.5A Dual Non-Inverting
MOSFET driver,
-40°C to +85°C
PDIP package.
a)
TC4428COA713:1.5A Dual Complementary
=
=
=
MOSFET driver,
0°C to +70°C,
SOIC package,
Tape and Reel.
b)
TC4428EMF:
1.5A Dual Complementary,
MOSFET driver,
-40°C to +85°C
DFN package.
Sales and Support
Data Sheets
Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and
recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following:
1.
2.
Your local Microchip sales office
The Microchip Worldwide Site (www.microchip.com)
Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using.
Customer Notification System
Register on our web site (www.microchip.com/cn) to receive the most current information on our products.
 2002-2012 Microchip Technology Inc.
DS21422E-page 17
TC4426/TC4427/TC4428
NOTES:
DS21422E-page 18
 2002-2012 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash
and UNI/O are registered trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MTP, SEEVAL and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
Analog-for-the-Digital Age, Application Maestro, BodyCom,
chipKIT, chipKIT logo, CodeGuard, dsPICDEM,
dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial
Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code
Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,
PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O,
Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA
and Z-Scale are trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
GestIC and ULPP are registered trademarks of Microchip
Technology Germany II GmbH & Co. & KG, a subsidiary of
Microchip Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2002-2012, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 9781620767979
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
== ISO/TS 16949 ==
 2002-2012 Microchip Technology Inc.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
DS21422E-page 19
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Osaka
Tel: 81-66-152-7160
Fax: 81-66-152-9310
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
China - Hangzhou
Tel: 86-571-2819-3187
Fax: 86-571-2819-3189
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
Taiwan - Kaohsiung
Tel: 886-7-213-7828
Fax: 886-7-330-9305
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
DS21422E-page 20
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
11/27/12
 2002-2012 Microchip Technology Inc.