TFDU4101-TR3

TFDU4101
www.vishay.com
Vishay Semiconductors
Infrared Transceiver Module (SIR, 115.2 kbit/s) for IrDA®
Applications
FEATURES
20110
DESCRIPTION
The TFDU4101 transceiver is an infrared transceiver module
compliant to the latest IrDA® physical layer standard for fast
infrared data communication, supporting IrDA speeds up to
115.2 kbit/s (SIR), and carrier based remote control modes.
Integrated within the transceiver module are a photo pin
diode, an infrared emitter (IRED), and a low-power control IC
to provide a total front-end solution in a single package. This
device covers the full IrDA range of more than 1 m using the
internal intensity control. With one external current control
resistor the current can be adjusted for shorter ranges
saving operating current operating in IrDA low power mode.
This Vishay SIR transceiver is using the lead frame
technology. 
The receiver output pulse duration is independent of the
optical input pulse duration and recovers always a fixed
pulse duration optimum for compatibility to standard
Endecs and interfaces. TFDU4101 has a tristate output and
is floating in shutdown mode with a weak pull-up.
• Operates from 2.4 V to 5.5 V within
specification over full temperature range from
- 30 °C to + 85 °C
• Split power supply, transmitter and receiver
can be operated from two power supplies
with relaxed requirements saving costs,
US - patent no. 6,157,476
• Low power consumption (< 0.12 mA supply current in
receive mode, no signal)
• Power shutdown mode (< 4 μA shutdown current in full
temperature range, up to 85 °C, < 10 nA at 25 °C)
• Surface mount package (L x W x H in mm): 9.7 × 4.7 × 4
• High efficiency emitter
• Low profile (universal) package capable of surface mount
soldering to side and top view orientation
• Directly Interfaces with various super I/O and controller
devices as e. g. TOIM4232
• Tri-state-receiver output, floating in shut down with a
weak pull-up
• Qualified for lead (Pb)-free and Sn/Pb processing (MSL4)
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
Printers, fax machines, photocopiers, screen projectors
Internet TV boxes, video conferencing systems
Medical data collection
Diagnostic systems
Notebook computers, desktop PCs, palmtop computers
(Win CE, Palm PC), PDAs
Internet TV boxes, video conferencing systems
External infrared adapters (dongles)
Data loggers
GPS
Kiosks, POS, point and pay devices
Industrial applications
PRODUCT SUMMARY
PART NUMBER
TFDU4101
DATA RATE
(kbit/s)
DIMENSIONS
HxLxW
(mm x mm x mm)
LINK DISTANCE
(m)
OPERATING
VOLTAGE
(V)
IDLE SUPPLY
CURRENT
(mA)
115.2
4 x 9.7 x 4.7
0 to  1
2.4 to 5.5
0.07
PARTS TABLE
PART
DESCRIPTION
QTY/REEL
TFDU4101-TR3
Oriented in carrier tape for side view surface mounting
1000 pcs
TFDU4101-TT3
Oriented in carrier tape for top view surface mounting
1000 pcs
Rev. 1.6, 04-Jul-12
Document Number: 81288
1
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TFDU4101
www.vishay.com
Vishay Semiconductors
FUNCTIONAL BLOCK DIAGRAM
VCC1
Tri-State
Driver
Amplifier
RXD
Comparator
VCC2
Logic
and
SD
Controlled
Driver
Control
TXD
18468
IRED C
GND
PIN DESCRIPTION
PIN
NUMBER
SYMBOL
DESCRIPTION
I/O
ACTIVE
1
VCC2
IRED anode
IRED anode to be externally connected to VCC2. An external resistor is
only necessary for controlling the IRED current when a current reduction
below 300 mA is intended to operate in IrDA low power mode.
This pin is allowed to be supplied from an uncontrolled power supply
separated from the controlled VCC1 - supply.
2
IRED cathode
TXD
This Schmitt-Trigger input is used to transmit serial data when SD is low.
An on-chip protection circuit disables the LED driver if the TXD pin is
asserted for longer than 50 μs (max. 300 μs).
IRED cathode, internally connected to driver transistor
3
I
High
4
RXD
Received data output, push-pull CMOS driver output capable of driving
standard CMOS or TTL loads. During transmission the RXD output is
active (echo-on). No external pull-up or pull-down resistor is required.
Floating with a weak pull-up of 500 k (typ.) in shutdown mode.
O
Low
I
High
5
SD
Shutdown
6
VCC1
Supply voltage
7
NC
No internal connection
8
GND
Ground
Rev. 1.6, 04-Jul-12
I
Document Number: 81288
2
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TFDU4101
www.vishay.com
Vishay Semiconductors
PINOUT
TFDU4101
Weight 200 mg
”U” Option Baby Face (universal)
IRED
1
2
Detector
3
4
5
6
7 8
17087
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITIONS
SYMBOL
MIN.
Supply voltage range,
transceiver
- 0.3 V < VCC2 < 6 V
VCC1
Supply voltage range,
transmitter
- 0.5 V < VCC1 < 6 V
Voltage at RXD
Voltage at all inputs and
outputs
Input currents
MAX.
UNIT
- 0.5
6
V
VCC2
- 0.5
6
V
- 0.5 V < VCC1 < 6 V
VRXD
- 0.5
VCC1 + 0.5
V
Vin > VCC1 is allowed
Vin
- 0.5
6
V
10
mA
For all pins, except IRED anode pin
Output sinking current
Power dissipation
See derating curve
Junction temperature
Ambient temperature range
(operating)
Storage temperature range
Soldering temperature
25
mA
PD
250
mW
TJ
125
°C
Tamb
- 30
+ 85
°C
Tstg
- 30
+ 85
°C
See “Recommended Solder Profile”
Average output current, pin 1
Repetitive pulse output current,
pin 1 to pin 2
< 90 μs, ton < 20 %
TYP.
260
°C
IIRED (DC)
80
mA
IIRED (RP)
400
mA
Note
• Reference point pin, GND unless otherwise noted. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production
testing.
EYE SAFETY INFORMATION
STANDARD
CLASSIFICATION
IEC/EN 60825-1 (2007-03), DIN EN 60825-1 (2008-05) “SAFETY OF LASER PRODUCTS - 
Part 1: equipment classification and requirements”, simplified method
Class 1
IEC 62471 (2006), CIE S009 (2002) “Photobiological Safety of Lamps and Lamp Systems”
Exempt
DIRECTIVE 2006/25/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 5th April 2006
on the minimum health and safety requirements regarding the exposure of workers to risks arising
from physical agents (artificial optical radiation) (19th individual directive within the meaning of article
16(1) of directive 89/391/EEC)
Exempt
Note
• Vishay transceivers operating inside the absolute maximum ratings are classified as eye safe according the above table.
Rev. 1.6, 04-Jul-12
Document Number: 81288
3
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TFDU4101
www.vishay.com
Vishay Semiconductors
ELECTRICAL CHARACTERISTICS
PARAMETER
TEST CONDITIONS/PINS
SYMBOL
MIN.
TYP.
MAX.
UNIT
5.5
V
130
μA
TRANSCEIVER
Supply voltage
VCC1
2.4
Dynamic supply current
SD = low, Ee = 1 klx (1),
Tamb = - 25 °C to + 85 °C
VCC1 = VCC2 = 2.4 V to 5.5 V
ICC1
40
90
Dynamic supply current
SD = low, Ee = 1 klx (1),
Tamb = 25 °C
VCC1 = VCC2 = 2.4 V to 5.5 V
ICC1
40
75
Average dynamic supply
current, transmitting
IIRED = 300 mA,
25 % duty cycle
ICC
0.65
2.5
mA
SD = high, T = 25 °C, Ee = 0 klx
no signal, no resistive load
ISD
0.01
0.1
μA
SD = high, T = 70 °C
no signal, no resistive load
ISD
1
μA
SD = high, T = 85 °C
no signal, no resistive load
ISD
1
μA
TA
- 30
+ 85
°C
Cload = 15 pF
VOL
- 0.5
0.15 x VCC1
V
IOH = - 500 μA, CLoad = 15 pF
VOH
0.8 x VCC1
VCC1 + 0.5
V
IOH = - 250 μA, CLoad = 15 pF
VOH
0.9 x VCC1
VCC1 + 0.5
V
RRXD
400
600
k
Shutdown supply current
Operating temperature range
Output voltage low, RXD
Output voltage high, RXD
RXD to VCC1 impedance
Input voltage low (TXD, SD)
Input voltage high (TXD, SD)
Input leakage current (TXD, SD)
Controlled pull down current 
0 < Vin < 0.15 VCC1
Vin > 0.7 VCC1
Input capacitance (TXD, SD)
500
μA
VIL
- 0.5
0.5
V
VIH
0.8 x VCC1
6
V
Vlogic > 2.5 V (2)
VIH
VCC1 - 0.5
6
V
Vin = 0.9 x VCC1
IICH
-2
+2
μA
SD, TXD = “0” or “1”
IIrTX
+ 150
1
μA
μA
5
pF
1.5 V  Vlogic  2.5 V (2)
-1
CI
0
Notes
• Tamb = 25 °C, VCC1 = VCC2 = 2.4 V to 5.5 V unless otherwise noted.
• Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
(1) Standard illuminant A.
(2) The typical threshold level is 0.5 x V
CC1. It is recommended to use the specified min./max. values to avoid increased operating current.
Rev. 1.6, 04-Jul-12
Document Number: 81288
4
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TFDU4101
www.vishay.com
Vishay Semiconductors
OPTOELECTRONIC CHARACTERISTICS
PARAMETER
(1)
TEST CONDITIONS
SYMBOL
MIN.
TYP.
MAX.
UNIT
Minimum irradiance Ee in
angular range (3) SIR mode
9.6 kbit/s to 115.2 kbit/s
 = 850 nm to 900 nm;  = 0°, 15°
Ee, min.
4
(0.4)
20
(2)
35 (2)
(3.5)
mW/m2
(μW/cm2)
Maximum irradiance Ee in
angular range (4)
 = 850 nm to 900 nm
Ee, max.
5
(500)
Rise time of output signal
10 % to 90 %, CL = 15 pF
tr (RXD)
20
100
ns
Fall time of output signal
90 % to 10 %, CL = 15 pF
tf (RXD)
20
100
ns
RXD pulse width
Input pulse length > 1.2 μs
tPW
1.65
3
μs
Input irradiance = 100 mW/m2,
 115.2 kbit/s
250
ns
After shutdown active or power-on
500
μs
100
150
μs
RECEIVER
Leading edge jitter
Standby/shutdown delay,
receiver startup time
Latency
tL
kW/m2
(mW/cm2)
2.2
TRANSMITTER
IRED operating current,
switched current limiter
Forward voltage of built-in
IRED
No external resistor for current limitation (5)
ID
250
300
350
mA
If = 300 mA
Vf
1.4
1.8
1.9
V
1
μA
Output leakage IRED current
IIRED
-1
Output radiant intensity
 = 0°, 15°
TXD = high, SD = low
Ie
48
Output radiant intensity
VCC1 = 5 V,  = 0°, 15°
TXD = low or SD = high (receiver is inactive
as long as SD = high)
Ie
Output radiant intensity,
angle of half intensity
p
Spectral bandwidth

Optical rise time, optical fall
time
mW/sr
0.04

Peak - emission wavelength (6)
65
± 24
880
mW/sr
deg
900
45
nm
nm
tropt, tfopt
10
300
ns
tTXD - 0.15
tTXD + 0.15
μs
300
μs
25
%
Optical output pulse duration
Input pulse width
1.6 μs < tTXD < 20 μs
topt
Optical output pulse duration
Input pulse width tTXD  20 μs
topt
Optical overshoot
20
Notes
(3) T
amb = 25 °C, VCC1 = VCC2 = 2.4 V to 5.5 V unless otherwise noted.
Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
(4) IrDA specification is 40 mW/m2. Specification takes a window loss of 10 % into account.
(5) IrDA sensitivity definition: minimum irradiance E in angular range, power per unit area. The receiver must meet the BER specification while
e
the source is operating at the minimum intensity in angular range into the minimum half-angular range at the maximum link length.
(6) Maximum irradiance E in angular range, power per unit area. The optical delivered to the detector by a source operating at the maximum
e
intensity in angular range at minimum link length must not cause receiver overdrive distortion and possible ralated link errors. If placed at
the active output interface reference plane of the transmitter, the receiver must meet its bit error ratio (BER) specification.
(7) Using an external current limiting resistor is allowed and recommended to reduce IRED intensity and operating current when current
reduction is intended to operate at the IrDA low power conditions. E.g. for VCC2 = 3.3 V a current limiting resistor of RS = 56  will allow a
power minimized operation at IrDA low power conditions.
(8) Due to this wavelength restriction compared to the IrDA spec of 850 nm to 900 nm the transmitter is able to operate as source for the
standard remote control applications with codes as e.g. Phillips RC5/RC6® or RECS 80.
For more definitions see the document “Symbols and Terminology” on the Vishay website.
Rev. 1.6, 04-Jul-12
Document Number: 81288
5
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TFDU4101
www.vishay.com
Vishay Semiconductors
RECOMMENDED CIRCUIT DIAGRAM
Operated with a clean low impedance power supply the
TFDU4101 needs no additional external components.
However, depending on the entire system design and board
layout, additional components may be required (see figure
1). That is especially the case when separate power supplies
are used for bench tests. When using compact wiring and
regulated supplies as e. g. in phone applications in most
cases no external components are necessary.
VIRED
R1*)
VCC
R2
C1
GND
VCC2 , IRED A
VCC1
C2
Ground
SD
SD
TXD
TXD
RXD
RXD
20037
IRED C
Fig. 1 - Recommended Test Circuit
Note
*) R1 is optional when reduced intensity is used.
The capacitor C1 is buffering the supply voltage and
eliminates the inductance of the power supply line. This one
should be a Tantalum or other fast capacitor to guarantee
the fast rise time of the IRED current. The resistor R1 is the
current limiting resistor, which may be used to reduce the
operating current to levels below the specified controlled
values for saving battery power.
Vishay's transceivers integrate a sensitive receiver and a
built-in power driver. The combination of both needs a
careful circuit board layout. The use of thin, long, resistive
and inductive wiring should be avoided. The shutdown input
must be grounded for normal operation, also when the
shutdown function is not used.
The inputs (TXD, SD) and the output RXD should be directly
connected (DC-coupled) to the I/O circuit. The capacitor C2
combined with the resistor R2 is the low pass filter for
smoothing the supply voltage. R2, C1 and C2 are optional
and dependent on the quality of the supply voltages VCC1
and injected noise. An unstable power supply with dropping
voltage during transmission may reduce the sensitivity (and
transmission range) of the transceiver.
The placement of these parts is critical. It is strongly
recommended to position C2 as close as possible to the
transceiver power supply pins.
When extended wiring is used (bench tests!) the inductance
of the power supply can cause dynamically a voltage drop
at VCC2. Often some power supplies are not able to follow
the fast current rise time. In that case another 4.7 μF (type,
see table under C1) at VCC2 will be helpful.
Under extreme EMI conditions as placing an
RF-transmitter antenna on top of the transceiver, we
recommend to protect all inputs by a low-pass filter, as a
minimum a 12 pF capacitor, especially at the RXD port. The
transceiver itself withstands EMI at GSM frequencies above
500 V/m. When interference is observed, the wiring to the
inputs picks it up. It is verified by DPI measurements that as
long as the interfering RF - voltage is below the logic
threshold levels of the inputs and equivalent levels at the
outputs no interferences are expected.
One should keep in mind that basic RF-design rules for
circuit design should be taken into account. Especially
longer signal lines should not be used without termination.
See e.g. "The Art of Electronics" Paul Horowitz, Winfield Hill,
1989, Cambridge University Press, ISBN: 0521370957.





TABLE 1 - RECOMMENDED TESTS AND APPLICATION CIRCUIT COMPONENTS
COMPONENT
RECOMMENDED VALUE
C1
4.7 μF, 16 V
293D 475X9 016B
C2
0.1 μF, ceramic
VJ 1206 Y 104 J XXMT
R1
R2
Depends on current to be adjusted, e. g. with VCC2 = 3.3 V 56  is an option for minimum low power operation
47 , 0.125 W
Figure 2 shows an example of a typical application with a
separate supply voltage VS and using the transceiver with
the IRED anode connected to the unregulated battery Vbatt.
This method reduces the peak load of the regulated power
supply and saves therefore costs. Alternatively all supplies
can also be tied to only one voltage source. R1 and C1 are
not used in this case and are depending on the circuit
design in most cases not necessary.
In figure 2 an option is shown to operate the transmitter at
two different power levels to switch for long range to low
Rev. 1.6, 04-Jul-12
VISHAY PART NUMBER
CRCW-1206-47R0-F-RT1
power mode for e.g. saving power for IrDA application but
use the full range specification for remote control. The
additional components are marked in the figure.
For operating at RS232 ports TOIM4232 is recommended
as ENDEC.
Document Number: 81288
6
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TFDU4101
www.vishay.com
Vishay Semiconductors
CURRENT DERATING DIAGRAM
Vs = 2.8 V
C1
R1
Vdd
IRTX
IRRX
IR MODE
R2
IRED Anode (1)
IRED Cathode (2)
TXD (3)
RXD (4)
SD (5)
Vcc1 (6)
C2
GND (8)
20038
Fig. 2 - Typical Application Circuit
Grey: Optional for High/Low Switching
I/O AND SOFTWARE
In the description, already different I/Os are mentioned.
Different combinations are tested and the function verified
with the special drivers available from the I/O suppliers. In
special cases refer to the I/O manual, the Vishay application
notes, or contact directly Vishay Sales, Marketing or
Application.
Figure 3 shows the maximum operating temperature when
the device is operated without external current limiting
resistor.
90
Ambient Temperature (°C)
Vbatt  3 V
Hi/Low
85
80
75
70
65
60
55
50
2
18097
2.5
3
3.5
4
4.5
5
5.5
6
Operating Voltage (V) at Duty Cycle 20 %
Fig. 3 - Current Derating Diagram
TABLE 2 - TRUTH TABLE
INPUTS
OUTPUTS
REMARK
SD
TXD
OPTICAL INPUT IRRADIANCE
mW/m2
High
> 1 ms
x
x
Weakly pulled
(500 k) to VCC1
0
Shutdown
High < 50 μs
x
Low active
Ie
Transmitting
High > 50 μs
x
High inactive
0
Protection is active
RXD
TRANSMITTER
OPERATION
Low
<4
High inactive
0
Ignoring low signals below the
IrDA defined threshold for noise
immunity
Low
> min. irradiance Ee
< max. irradiance Ee
Low (active)
0
Response to an IrDA compliant
optical input signal
Low
> max. irradiance Ee
Undefined
0
Overload conditions can cause
unexpected outputs
Low
Rev. 1.6, 04-Jul-12
Document Number: 81288
7
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TFDU4101
www.vishay.com
Vishay Semiconductors
RECOMMENDED SOLDER PROFILES
275
Solder Profile for Sn/Pb Soldering
T ≥ 255 °C for 10 s....30 s
250
260
240
220
200
180
160
140
120
100
80
60
40
20
0
240 °C max.
10 s max. at 230 °C
2 to 4 °C/s
160 °C max.
Temperature/°C
Temperature (°C)
225
Tpeak = 260 °C
T ≥ 217 °C for 70 s max.
200
175
150
30 s max.
125
100
90 s to 120 s
70 s max.
2 °C/s to 4 °C/s
75
120 to180 s
2 °C/s to 3 °C/s
50
90 s max.
25
2 to 4 °C/s
0
0
50
100
19532
150
200
250
300
350
Time/s
Fig. 5 - Solder Profile, RSS Recommendation
0
50
19535
100
150
200
250
300
350
Time/s
280
Fig. 4 - Recommended Solder Profile for Sn/Pb Soldering
Tpeak = 260 °C max.
240
The TFDU4101 is a lead (Pb)-free transceiver and qualified
for lead (Pb)-free processing. For lead (Pb)-free solder paste
like Sn(3.0-4.0)Ag(0.5-0.9)Cu, there are two standard reflow
profiles: Ramp-Soak-Spike (RSS) and Ramp-To-Spike
(RTS). The Ramp-Soak-Spike profile was developed
primarily for reflow ovens heated by infrared radiation. With
widespread use of forced convection reflow ovens the
Ramp-To-Spike profile is used increasingly. Shown below in
figure 5 and 6 are Vishay's recommended profiles for use
with the TFDU4101 transceivers. For more details please
refer to the application note “SMD Assembly Instructions”.
A ramp-up rate less than 0.9 °C/s is not recommended.
Ramp-up rates faster than 1.3 °C/s could damage an optical
part because the thermal conductivity is less than compared
to a standard IC.
Temperature/°C
Lead (Pb)-free, Recommended Solder Profile
200
< 4 °C/s
160
1.3 °C/s
120
Time above 217 °C t ≤ 70 s
Time above 250 °C t ≤ 40 s < 2 °C/s
Peak temperature Tpeak = 260 °C
80
40
0
0
TFDU Fig3
50
100
150
200
250
300
Time/s
Fig. 6 - RTS Recommendation
Wave Soldering
For TFDUxxxx and TFBSxxxx transceiver devices wave
soldering is not recommended.
Manual Soldering
Manual soldering is the standard method for lab use.
However, for a production process it cannot be
recommended because the risk of damage is highly
dependent on the experience of the operator. Nevertheless,
we added a chapter to the above mentioned application
note, describing manual soldering and desoldering.
Storage
The storage and drying processes for all Vishay transceivers
(TFDUxxxx and TFBSxxx) are equivalent to MSL4.
The data for the drying procedure is given on labels on the
packing and also in the application note “Taping, Labeling,
Storage and Packing”.
Rev. 1.6, 04-Jul-12
Document Number: 81288
8
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TFDU4101
www.vishay.com
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
7x1=7
0.6
2.5
1
8
18470
1
Fig. 7 - Package Drawing TFDU4101. Tolerance ± 0.2 mm if not otherwise mentioned
20035
Fig. 8 - Recommended Footprint for Side View Applications and Solderpaste Mask
Rev. 1.6, 04-Jul-12
Document Number: 81288
9
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TFDU4101
www.vishay.com
Vishay Semiconductors
20036
Fig. 9 - Recommended Footprint for Top View Applications and Solderpaste Mask
REEL DIMENSIONS in millimeters
Drawing-No.: 9.800-5090.01-4
Issue: 1; 29.11.05
14017
TAPE WIDTH
(mm)
A MAX.
(mm)
N
(mm)
W1 MIN.
(mm)
W2 MAX.
(mm)
W3 MIN.
(mm)
W3 MAX.
(mm)
24
330
60
24.4
30.4
23.9
27.4
Rev. 1.6, 04-Jul-12
Document Number: 81288
10
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TFDU4101
www.vishay.com
Vishay Semiconductors
TAPE DIMENSIONS in millimeters
Drawing-No.: 9.700-5251.01-4
Issue: 3; 02.09.05
19824
Fig. 10 - Tape Drawing, TFDU4101 for Top View Mounting, Tolerance ± 0.1 mm
HANDLING PRECAUTION
Sagging of carrier tape may cause some units to rotate and will result to pick-and-place problem. Do not allow carrier tape to
sag as shown in picture below.
Rev. 1.6, 04-Jul-12
Document Number: 81288
11
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TFDU4101
www.vishay.com
Vishay Semiconductors
19875
Fig. 11 - Tape Drawing, TFDU4101 for Side View Mounting, Tolerance ± 0.1 mm
Rev. 1.6, 04-Jul-12
Document Number: 81288
12
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000