Designed and Manufactured in Germany Specification Oscillator type: Rev.: 3 Date: 2014-07-08 AXIOM75-11 Low Phase Noise OCXO with Sine Wave Output Parameter min. Nominal frequency Frequency stability Initial tolerance @+25°C vs. operating temperature range operating temperature range vs. supply voltage variation vs. load change Long term (aging) per day st Long term (aging) 1 year Frequency adjustment range Electronic Frequency Control (EFC EFC voltage VC EFC slope (∆f / ∆VC) EFC input impedance RF output Signal waveform Output level Harmonics Spurious Warm-up time Phase noise typ. max. 10.000 0 ±1 ±0.8 0.25 ±1 2.50 Positive Condition MHz ±500 ±25 +70 ±10 ±5 ±2 ±100 ppb ppb °C ppb ppb ppb ppb 4.75 ppm V 100 @ VC = 2.5 V steady state VS ±5% RL ±5% after 30 days operation after 30 days operation kΩ Sine wave RL = 50 Ω +7 -30 -90 5 -140 -150 -155 -160 12.0 Supply voltage VS Current consumption (steady state) Current consumption (warm-up) Operable temperature range Storage temperature range 11.4 Enclosure (see drawing) Weight Packing ESD Sensitivity 25.8x25.8x13.5 max. 10 Palette 1500 Notes: 1. Unit -20 -40 12.6 100 250 +75 +85 dBm dBc dBc min dBc/Hz dBc/Hz dBc/Hz dBc/Hz V mA mA °C °C ∆ffinal/f0 < ±0.1 ppm @ 100 Hz @ 1kHz @ 10 kHz @ 100 kHz @ +25°C mm g V HBM as in IEC 61000-4-2 Terminology and test conditions are according to IEC standard IEC60679-1, unless otherwise stated Ordering Code: Model (Specification) AXIOM75-11 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany Revision Rev.3 Frequency [MHz] 10.000 AXIOM75-11 Rev.3 Drawing D1 Page 1(2) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Enclosure drawing Pin connections Pin # 1 2 3 4 5 Symbol RF OUT GND VC N.C. VS Function RF Output Ground Control Voltage (EFC) No Connection Supply Voltage Environmental conditions Test Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60068 Part ... 2-17 IEC 60679-1 clause ... 4.6.2 2-20 2-58 4.6.3 2-27 4.6.8 Test conditions Gross leak: Test Qc, Fine leak: Test Qk Test Ta (235 ± 5)°C Method 1 Test Tb Method 1A, 5s Vibration, sinusoidal* 2-6 4.6.7 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Endurance tests - ageing - extended aging 4.7.1 4.7.2 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C Revision History Rev. Drawing Date [dd.mm.yyyy] 3 3 D0 D1 08.09.2009 08.07.2014 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany Remarks New package drawing with 0.5 mm pins Editorial changes AXIOM75-11 Rev.3 Drawing D1 Page 2(2) Author Checked BN HH BN HH www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]