VEAM PT

ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 1
L
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 5
VEAM PT Connectors
Features and Benefits
• Retained coupling nuts on plugs
• Heavy (arctic) ribbed coupling nuts available
• Many special variants/platings/materials
• Numerous contact arrangements from 2 to 61 contacts
• Alternate keyway polarization and insert orientations
to prevent cross-plugging
• Available with grounding springs for EMC shielding
• Positive coupling 3 bayonet pin construction with audible mate
• Solder or crimp terminations
• Wide range of cable accessories
Materials
Shells:
Insulator:
Contacts:
High-grade aluminum alloy suitably plated
Polychloropene rubber/self extinguishing/resistant to hydraulic fluids, lubricants etc,
Gold plated high conductivity copper alloy
Environmental Ratings
Temperature range
Humidity
Low air pressure
Vibration
Shock
Bump
Acceleration
Mechanical endurance
Salt mist
Sealing (PT series only)
-55º to +125ºC
56 days
44 mbar
10 - 5000Hz, 0.75mm/10gn duration 30 hr
981m/s2 (100n) for 6 ms
390 m/s2 (40gn) 4000 bumps
490 m/s2 (50gn)
500 matings
Severity 1 to BS2011 Kb (dependent on finish)
<1 cm 3/h at 100 kN/m2 (1 bar)
Electrical Ratings
2100 or 3000V d.c. or a.c. peak
5000M 1 minimum
5 m 1 maximum
5 m 1 maximum (grounding spring styles)
Contact size 20, 5 amps
Contact size 16, 10 amps
Contact size 12, 20 amps
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-5
L
VEAM PT
Proof voltage rating
Insulation resistance
Contact resistance
Shell to shell continuity
Current rating
@ 85º continuous
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 6
VEAM PT Connectors
Glossary of Terms
Shown below are some standard terms used to describe circular
connectors and their features
Shell
The body of the connector
Insert
The dielectric or insulating inner core, holds contacts
Coupling Nut
Outer threaded or grooved ring which holds mated pair together
Jam Nut
Nut that holds receptacle to a panel
Bayonet Coupling
A non-threaded, triple ramp type of coupling
Contacts
The conductive element in a connector that makes the
electrical connection between mated connectors
Pin Contact*
Male half of a mated pair of contacts
Socket Contact
Female half of a mated pair of contacts
Solder Contact
A contact to which wire is joined by soldering
Crimp Contact
A contact to which wire is joined by mechanical compression
VEAM PT
L
Plug* (Free)
The male half of a mating pair of connectors which may
hold male or female insert/contacts
Receptacle (Fixed)
The female half of a mating pair of connectors which may hold
male or female insert/contacts
PCB contacts
Contacts that can be soldered to a printed circuit board
or flex circuit
Plating
The metal finish applied to contacts and or shell components (protective)
Grommet
Resilient part at back of insert (attached or separate) gives wire
moisture seal
Gland
Resilient ring in rear accessory provides seal on wire jacket
Sealing Plug
Plastic peg placed in unused grommet holes to seal
Grounding Fingers
A metal strap around the plug shell for positive electrical shell
to shell connection
Hermetic
A connector with fused glass insert for air tightness
Mating/Un mating Forces
Torque required to couple/uncouple a mating pair
Backshell
An accessory which threads to back of shell
Strain Relief
A type of accessory which clamps wires for support
Potting Boot
A type of accessory which forms a mould for potting compound
EMI or RFI Backshell
A type of accessory to terminate wire/cable shielding
Interfacial Seal
A resilient gasket on the face of pin inserts gives moisture seal
Scoop Proof
Is a feature on some ranges of connectors to prevent damage to the
pin contacts when mating connector pairs
*Note: Male half always goes into female
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-6
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 7
VEAM PT Connectors
Terminology: Cylindrical Connectors
The diagram opposite shows a typical cross-section of a mated pair of
connectors, indicating the basic components.
Basic Components:
1. Body (Shell)
2. Insert (Dielectric Contact Holder) Pin or Socket
3. Contact (Wire End Termination) (Signal Joining Part)
4. Accessories (Wire Seals, Cable Seals, Wire Support, etc.)
Receptacle
Coupling Nut
Contacts
Insert
Backshell
Plug
Grommet
Body Styles:
Wall Mount Recept.
Cable Connecting Recept.
Box Mount Recept.
Solder Mount Recept. (Hermetic)
Jam Nut Recept.
Straight Plug
Coupling: Bayonet
Shell Sizes (typical):
8, 10, 12, 14, 16,
18, 20, 22, 24
L
Not in PT
Plug
06
08
55
Shell Styles
Straight
90º
Straight less rear
accessory (PT)
Plug
00/33
01/44
02
Shell Styles
Wall Mount
Cable Connecting
Box Mount
(less rear accessory)
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-7
Plug
07
Shell Styles
Jam Nut
VEAM PT
Style Designation (Typical)
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 8
VEAM PT Connectors
Terminology: Cylindrical Connectors
Inserts
• Solder
• Crimp
Metal Clip Retention
Distortable rubber retention
Insert (Pin or Socket)
Insert & Grommet Accessory
May include a soft front interfacial seal (Bonded) if dielectric
is hard, and a rear sealing grommet separate or attached.
Contacts
Pin Crimp*
Socket-Crimp*
Pin-Solder
Socket-Solder
Contact sizes:
Contact size
22D Not PT
22M Not PT
22 Not PT
20
16
12
8
4 Not PT
0 Not PT
AWG Wire Size
22-28
24-28
22-26
20-24
16-20
12-14
8-10
4-6
0-2
Size by Wire Gauge
4/0 AWG 4/0
PCB pin contact
PCB socket contact
*Crimps are removable
VEAM PT
L
PIN
SOCKET
CRIMP OR SOLDER
Usually seperate from
insert, shipped loose or in
bulk, tools needed to
crimp, install and remove
Usually installed in insert,
frequently bonded in place.
PC TAIL
CO-AXIAL
THERMOCOUPLE
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-8
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 9
VEAM PT Connectors
PT/PTSE Connectors
PT Solder Connectors
PTSE Crimp Connectors
Part Number Breakdown
Part Number Nomenclature for Solder Connector
To more easily illustrate ordering procedure, part number
PT33A20 41PW(SR) is shown as follows:
Part Number Breakdown
Proprietary Part Number Construction for Crimp Connectors
To more easily illustrate ordering procedure, part number PT33A20
41PW(SR) is shown as follows:
PART NUMBER
PART NUMBER
PT
33
A-
20 - 41
P
W
(SR)
PT
33
A-
1
2
3
4
6
7
8
1
2
3
5
4
5
P
W
(SR)
6
7
8
See code below:
See code below:
1. Connector Families:
PT designates standard olive drab Tri-Lock coupling connector.
This is the Veam proprietary version of the MIL-C-26482 solder
contact connector B59522F0017 (Pattern 105).
1. Connector Families:
PT**SE designates standard olive drab Tri-Lock coupling
connector with removable crimp contacts.
2. Shell Styles:
“33’
designates wall mount receptacle.
“55”
designates cable connecting plug.
“02”
designates box mount receptacle.
“44”
designates in line receptacle.
“06”
designates cable connect plug with accessory
“07”
designates jam nut receptacle.
“08”
designates 90º plug.
2. Shell Styles:
“33”
designates wall mount receptacle.
“55”
designates cable connecting plug.
“02”
designates box mount receptacle.
“44”
designates in line receptacle.
“06”
designates cable connect plug with accessory
“07”
designates jam nut receptacle.
“08”
designates 90º plug.
PTB
designates thru-bulkhead receptacle.
3. Service Classes:
“SE”
designates environmental crimp. The above are proprietary versions of the MIL-C-26482 crimp contact
connector. The contact retention mechanism consists
of a metal clip held in place by a nylon wafer.
3. Service Classes:
“A”
designates general duty back shell.
“E”
designates environmental resisting with grommet
and nut.
“P”
designates potted with potting boot.
“W”
designates compressing clamp and neoprene gland
for moisture-proofing, multi-jacketed cables.
“H”
designates hermetic seal receptacle.
4.“20” designates shell size. Shell sizes available
are 8 through 24.
5.“20-41” designates insert arrangements.
4.“20” designates shell size. Shell sizes available
are 8 through 24.
6. “P”
designates pin contacts. “S” for socket contacts.
designates pin contacts. “S” for socket contacts.
7. “W” designates that insert is rotated in its shell from
the standard position to alternate position W. The basic
rotations are W, X, Y and Z. No letter required for normal (no rotation) position. The keyways can also be
oriented in various positions. The basic rotations are B,
C, E and F.
8. “SR” designates a strain relief clamp. Deviation suffixes
would be inserted here. For example: (T01) Ribbed
coupling Nut.
8. “SR” designates a strain relief clamp. Deviation suffixes
would be inserted here. For example: (T01) Ribbed
coupling Nut.
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-9
L
VEAM PT
7. “W” designates that insert is rotated in its shell from
the standard position to alternate position W. The basic
rotations are W, X, Y and Z. No letter required for normal (no rotation) position. The keyways can also be
oriented in various positions. The basic rotations are B,
C, E and F.
5.“20-41” designates insert arrangements.
6. “P”
20 - 41
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 10
VEAM PT Connectors
Contact Arrangements PT, PTSE, CPT & Audio Connectors
CONTACT ARRANGEMENTS
VEAM PT
L
Contact
Arrangements
Voltage
Rating
Total
Contacts
8-2
8-3
8-4
8-33
8-98
10-2
10-6
10-7
SP 10-98
SP 10-99
12-3
SP 12-4
12-8
12-10
14-2
14-5
14-12
14-15
SP 14-18
14-19
SP 14-22
SP 14-91
16-8
16-23
16-26
SP 16-99
18-11
SP 18-30
18-32
18-50
20-16
SP 20-24
SP 20-25
SP 20-27
20-39
20-41
SP 22-9
22-21
SP 22-32
SP 22-36
SP 22-41
22-55
24-61
1
1
1
1
1
2
1
1
1
1
2
2
1
1
2
2
1
1
1
1
1
*
2
1
1
1
2
1
1
2
2
1
1
1
1
1
1
2
1
1
1
1
1
2
3
4
3
3
2
6
7
6
7
3
4
8
10
2
5
12
15
18
19
5
3
8
23
26
23
11
30
32
2
16
24
25
27
39
41
9
21
32
36
41
55
61
Contact Size
20
16
12
coax
Plan forms available in the following range:
8
2
3
4
3
3
2
6
7
6
7
4
8
10
3
4
2
8
14
18
19
1
3
22
26
21
29
32
5
4
1
4
8
1
2
11
1
2
16
24
25
27
37
41
4
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5
21
32
36
27
55
61
PT
14
•
•
•
•
•
•
PTSE
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
CPT AUDIO
**
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
KEY
•
•
•
•
•
•
•
•
•
Preferred ranges
Non Preferred
Consult ITT for
other arrangements.
VOLTAGE RATING
1
2100 dc or ac peak
2
3000 dc or ac peak
•
*
**
•
5Kv rms
See Audio Connectors
(pages 00 & 00) for
contact arrangements to
shell style availability.
•
•
•
•
•
•
•
•
•
•
SP= Propriety to ITT Corporation
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-10
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 11
VEAM PT Connectors
Contact Arrangements - Preferred Ranges
8-2
2 X #20
1
B A
B
10-6
6 X #20
1
F A
B
E
D C
A
G
B
D
C
G
12-8
8 X #20
1
A
B
F
E
C
D
14-5
5 X #16
2
A
B
E
D
C
M
S
J
P
U
T
B
R
C
D
H
C
14-18
18 X #20
1
8
3 X #20
1
B
A
F
E
B
C
G
D
C
G
J
K
F
H
G
B
A
E
J
C
D
A
B
M
K
F
E
C
L
D
M A
B
LN
P
C
V
R
U
J
T S D
H G F E
K
10-7
7 X #20
1
10-2
2 X #16
2
A
B
A
E
B
D
CONTACT LEGEND
Contact Arrangement
Number of Contacts
Size of Contacts
Service Rating
8
12
20
coax
16
10-98
6 X #20
1
F
C
12-3
3 X #16
2
A
B
H
8-4
4 X #20
1
A D
B C
12-4
4 X #16
2
12-10
1 X #20
10 X #20
14-12
8 X #20
4 X #16
1
14-2
2 X #12
2
A
B
A
L M B
N
K R
C
P
J
D
H
G F E
14-19
19 X #20
1
G F E
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-11
A
B
E
C
D
14-15
14 X #20
1 X #16
1
14-22
1 X #20
4 X #12
1
L
VEAM PT
A
N
L
K
B
A
10-99
7 X #20
1
F
E
C
8-33
3 X #20
1
A
C
8-3
3 X #20
1
A
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 12
VEAM PT Connectors
Contact Arrangements - Preferred Ranges
P A
R
S
N
A
B
C
A
14-91
3 X #20
5 KV ms
G
P
16-26
26 X #20
1
N Y
M
Z
W
E
K
18-50
2 X #8
2
A
D
V
X
F
G
H
A
S
d
P
B
T
c
N
C
U
e
D
V
b
M
a
L
g
E
f
W
F
X
Z
Y
K
B
Z
X
W
K
D
U
V
H
F
G
A
H
B
K
G
D
F
E
T
S
18-30
29 X #20
1 X #16
1
R
d
P
B
W
j
g
M
B
M
K
S
N
C
J
R
P
D
H
E
G
F
L
G
K
H
J
W
P
C
R
U
G
B
Z
V
H
Y
a
N
N
X
K
T
F
R
P
A
S
E
D
20-24
24 X #20
1
W
M
B
S
X
C
b
D
T
Y
E
Z
a
L
V
U
J
H
F
20-25
25 X #20
1
G
K
VEAM PT
L
F
20-16
16 X #16
2
E
Y
Z
a
J
M
L
A
D
X
h
b
18-32
32 X #20
1
C
V
f
c
N
G
A
U
e
A
L
18-11
11 X #16
2
C
L
H
J
16-23
22 X #20
1 X #16
1
C
T
E
J
16-99
21 X #20
2 X #16
1
C
U
J
Y
L
B
T
L
M
J
A
S
R
B
D
R
A
B
S T
C
U
N
a
b
D
M Z
V
c
Y
L
X W E
K
F
J HG
C
E
R
P
B
H
F
16-8
8 X #16
2
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-12
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 13
VEAM PT Connectors
Contact Arrangement — Preferred Ranges
A
R
B
P
a
N
S
Z
M
b
c
d
Y
X
L
T
D
U
V
W
g
q
R
f
G
M
a
S
c
C
X
J
T
d
f
F
G
d
U
T
e
U
22-32
32 X #20
1
f
H
N
22-9
4 X #20
5 X #12
1
H
B
J
C
G
D
F
G
U
b
g
H
e
f
M
G
d
22-41
27 X #20
14 X #16
1
j
P
L
m
AA
k
z
R
J
A
B
P
R
W
L
S
D
T
U
J
22-21
21 X #16
2
C
X
V
K
E
F
G
h
Y
g
Z
s
EE
t
u
R
m
e
P
d
e
t
l
N
M
c
d
V
f
c
F
b
v
K
E
a
DD
f
L
22-55
55 X #20
1
D
r
CC
w
M
K
X
C
g
h
W
n
j
X
k
b
a
K
J
D
22-36
36 X #20
1
E
Y
F
Z
G
L
G
B
U
S
C
HH
FF
x
N
BB
A
T
B
q
GG
y
i
J
P
N
F
p
q
h
R
E
c
t
r
S
D
A
V
n p W
U
T
S
n
s
i
T
H
K
L
H
C
m
j
V
G
c
E
B
a
k
W
p
D
F
A
Z
F
b
d
M
M
E
Y
E
a
n
e
P
J
H
V
W
X
m
t
q
r
g
R
D
Z
s
h
20-41
41 X #20
1
C
Y
k
i
S
B
X
j
N
i
Y
E
A
W
V
A
B
R
h
g
Z
D
c
K
L
A
P
b
a
b
e
N
H
N
M
m
n
p
P
J
K
h
S
Z
k
r
20-39
37 X #20
2 X #16
1
C
Y
i
T
B
X
j
U
F
K
L
E
A
W
V
20-27
27 X #20
1
C
H
H
J
L
c
GG HH
w
t
W
s
FF
V
r
EE
U
q
T
NN
MM
DD
PP
g
z
BB
AA
k
j
M
L
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-13
E
F
G
h
i
m
N
D
f
y
KK
LL
C
e
x
n
P
B
d
JJ
CC
S p
R
b A
v
u
K
J
H
24-61
61 X #20
1
VEAM PT
Z a
Y
X
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 14
VEAM PT Connectors
Polarization
To avoid cross plugging of similar connectors which may be adjacently mounted, polarization is achieved by shell key/keyways. Up to five alternative
positions are available designated N, B, C, E or F. The Diagrams illustrate the angular variation of the keys with the master key being the datum point.
Where no specific polarization is requested, the neutral position N will always be applied.
Normal
Shell
Size
8
10
12
14
16
Normal
B
0
105
1050
1050
1050
1050
C
85
89
91
93
E
C
B
125
121
119
117
E
Shell
Size
18
20
22
24
F
182
115
115
75
75
82
85
85
120
120
F
Normal
0
105
1050
1050
1050
B
C
E
F
95
95
97
97
115
115
113
113
75
75
75
75
120
120
120
120
Insert Orientation
E
C
D
A
C
B
E
D
E
A
B
The diagrams below illustrates the angular displacement of the insert within the housing, for each orientation in the
range. This method is non-preferred and is intended for replacement purposes only.
A
B
A
Y
X
W
Availability
N
VEAM PT
L
L
B
8-2
8-3
8-4
8-33
8-98
L
L
L
L
L
14-2
14-5
14-12
14-15
14-18
14-19
14-22
14-91
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
20-16
20-24
20-25
20-27
20-39
20-41
L
L
L
L
L
L
L
L
L
L
L
L
C
E
F
W
Z
Availability
X
Y
Z
E
F
L I I
L
L I
L I
L
10-2
10-6
10-7
10-98
10-99
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L I
L
L
L
12-3
12-4
12-8
12-10
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
I
L
L I I I I
L I I I I
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
16-8
16-23
16-26
16-99
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
18-11
18-28
18-30
18-32
18-50
18-80
18-98
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L I I I I
L
L
L
L I I I I
L I I I
22-7
L L L L L I I I I
I I I I
I I
I I I I
N
B
C
E
F
W
Availability
L
L
L
L
L
X
Y
Z
I I I I
I I
I
I I
I I I I
I I I
Preferred type
Not Available
I
E
E
B
B
C
Normal
D
C
D
A
C
D
22-7
22-9
22-21
22-32
22-34
22-36
22-41
22-55
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
I I
I I I I
N
B
C
W
X
Y
Z
I I I I
I I I I
I I I I
I I I I
I I I I
I I I
I I I I
N.B. Consult factory for availability of
contact arrangements not shown
For replacement purposes only
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-14
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 15
VEAM PT Connectors
How to Order PT Jam Nut Connectors
SERIES/
PREFIX
SHELL
STYLE
SHELL SIZE/
LAYOUT
CONTACT
TYPE
polarization
CLASS
PLATING/
MOD CODE
NOTE 1
NOTE 1
NOTE 2
NOTE 3
NOTE 4
NOTE 5
07
A
(22-55)
S
(B)
(T69)
PT
77
E
P
SE
How To Order
1 Select the shell style and
classification eg. PT07E from following pages.
2 Add the shell size and contact arrangement
eg. PT07E22 55 see pages L-10 to L-13.
3 Add the contacts P=pins, S= sockets eg. PT07E22 55S.
4 For polarization add the relevant letter (E, B, C, F) or for orientation
add (W, X, Y, Z) from page 14. For normal orientation no letter required.
5 Add suffix as required from typical list below.
No Code
023
T69
T61
T21
T62/T65/T66
Olive drab cadmium plate finish as standard (historically 014)
Electroless Nickel plating finish
Zinc Cobalt Olive drab plate finish GB62
Zinc Cobalt Black plate finish (ROHS)
Marine ally Bronze (contact factory)
Pin tail contacts (contact factory)
PT07 Cutout Details
• Formed locking jam nut standard
• Drilled locking nut available at extra cost
• Solid locking nut available for size 8/10/12
• Circular lock nut with slots for size 8 available
L
H
J
K
K
PT07
Mounted from rear
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-15
H
±.005
J Dia.
±.005
K
Min
Min.
8
.540
10
.665
12
L
Max.
.572
.969
.062
.125
.697
1.093
.062
.125
.828
.885
1.281
.062
.125
14
.952
1.010
1.406
.062
.125
16
1.078
1.135
1.531
.062
.125
18
1.201
1.260
1.656
.062
.125
20
1.326
1.385
1.843
.062
.250
22
1.451
1.510
1.969
.062
.250
24
1.576
1.635
2.093
.062
.250
VEAM PT
Shell
Size
L
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 16
VEAM PT Connectors
PT07A Jam Nut Receptacle without Rear Accessory Thread (Solder Contacts)
M
Z
S
Q
A
R
P
K
ʻAʼ General Duty
Shell size
jam nut
tolerance
A
diameter
Q
diameter
M
depth
T
length
S
diameter
K
panel thickness
R
.003 (0.08)
.017 (0.43)
.031 (0.08)
max
max
min
max
thread
8
0.47
0.750
0.696
0.191
0.956
0.06
0.13
.5625-24 UNEF
10
0.59
0.875
0.696
0.191
1.062
0.06
0.13
.6875-24 UNEF
12
0.75
1.062
0.696
0.191
1.250
0.06
0.13
.8750-20 UNEF
14
0.88
1.188
0.696
0.191
1.375
0.06
0.13
1.000-20 UNEF
16
1.00
1.312
0.696
0.191
1.500
0.06
0.13
1.125-18 UNEF
18
1.13
1.458
0.696
0.191
1.625
0.06
0.13
1.250-18 UNEF
20
1.25
1.562
0.884
0.221
1.812
0.06
0.255
1.375-18 UNEF
22
1.38
1.688
0.884
0.221
1.938
0.06
0.255
1.500-18 UNEF
24
1.50
1.812
0.917
0.188
2.062
0.06
0.255
1.625-18 UNEF
PT07A Jam Nut Receptacle with Internal Rear Accessory Thread (Solder Contacts)
S
Q
N
M
H
U
VEAM PT
L
KK
Shell size
nut
tolerance
N
diameter
Q
diameter
M
depth
T
length
S
diameter
TT
H
panel thickness
G
V
rear diameterjam
.003 (0.08)
.017 (0.43)
.031 (0.08)
max
max
min
max
max
thread
8
0.473
0.750
0.696
0.568
0.956
0.06
0.125
0.729
.5625-24 UNEF
10
0.590
0.875
0.696
0.568
1.062
0.06
0.125
0.854
.6875-24 UNEF
12
0.750
1.062
0.696
0.568
1.250
0.06
0.125
0.979
.8750-20 UNEF
14
0.875
1.188
0.696
0.568
1.375
0.06
0.125
1.104
1.000-20 UNEF
16
1.000
1.312
0.696
0.568
1.500
0.06
0.125
1.229
1.125-18 UNEF
18
1.125
1.458
0.696
0.568
1.625
0.06
0.125
1.354
1.250-18 UNEF
20
1.250
1.562
0.884
0.63
1.812
0.06
0.250
1.510
1.375-18 UNEF
22
1.375
1.688
0.884
0.63
1.938
0.06
0.250
1.635
1.500-18 UNEF
24
1.500
1.812
0.917
0.66
2.062
0.06
0.250
1.760
1.625-18 UNEF
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-16
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 17
VEAM PT Connectors
PT77A Jam Nut Receptacle with External Rear Accessory Thread (Solder Contacts)
S
Q
D
P
V
H
U
N
Shell size
tolerance
D
diameter
.003 (0.08)
Q
V
diameter
depth
.017 (0.43) .031 (0.08)
K
U
length
max
S
diameter
max
H
panel thickness
min
max
K
rear diameter
max
P
jam nut
thread
N
rear access
thread
8
0.473
0.750
0.606
0.286
0.956
0.06
0.125
0.436
.5625-24 UNEF
.4375-28 UNEF
10
0.590
0.875
0.606
0.286
1.062
0.06
0.125
0.561
.6875-24 UNEF
.5625-24 UNEF
12
0.750
1.062
0.606
0.286
1.250
0.06
0.125
0.686
.8750-20 UNEF
.6875-24 UNEF
14
0.875
1.188
0.606
0.286
1.375
0.06
0.125
0.811
1.000-20 UNEF
.8125-20 UNEF
16
1.000
1.312
0.606
0.286
1.500
0.06
0.125
0.936
1.125-18 UNEF
.9375-20 UNEF
18
1.125
1.458
0.606
0.286
1.625
0.06
0.125
1.061
1.250-18 UNEF
1.0625-18 UNEF
20
1.250
1.562
0.764
0.306
1.812
0.06
0.250
1.186
1.375-18 UNEF
1.1875-18 UNEF
22
1.375
1.688
0.764
0.306
1.938
0.06
0.250
1.311
1.500-18 UNEF
1.3125-18 UNEF
24
1.500
1.812
0.782
0.306
2.062
0.06
0.250
1.436
1.625-18 UNEF
1.4375-18 UNEF
PT07SE Jam Nut Receptacle with Internal Rear Accessory Thread (Crimp Contacts Supplied)
S
Q
N
M
H
U
TT
KK
tolerance
N
Q
diameter
diameter
.003 (0.08) .017 (0.43)
M
depth
.031 (0.08)
U
length
max
S
diameter
max
H
panel thickness
min
max
KK
rear diameter
max
P
jam nut
thread
TT
rear internal
thread
8
0.473
0.750
0.696
0.376
0.956
0.06
0.125
0.719
.5625-24 UNEF
.6250-28 UNEF
10
0.590
0.875
0.696
0.376
1.062
0.06
0.125
0.844
.6875-24 UNEF
.7500-24 UNEF
12
0.750
1.062
0.696
0.376
1.250
0.06
0.125
0.969
.8750-20 UNEF
.8750-24 UNEF
14
0.875
1.188
0.696
0.376
1.375
0.06
0.125
1.094
1.000-20 UNEF
1.000-20 UNEF
16
1.000
1.312
0.696
0.376
1.500
0.06
0.125
1.219
1.125-18 UNEF
1.125-20 UNEF
18
1.125
1.458
0.696
0.376
1.625
0.06
0.125
1.344
1.250-18 UNEF
1.250-18 UNEF
20
1.250
1.562
0.884
0.391
1.812
0.06
0.250
1.500
1.375-18 UNEF
1.375-18 UNEF
22
1.375
1.688
0.884
0.391
1.938
0.06
0.250
1.625
1.500-18 UNEF
1.500-18 UNEF
24
1.500
1.812
0.917
0.411
2.062
0.06
0.250
1.750
1.625-18 UNEF
1.625-18 UNEF
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-17
VEAM PT
Shell size
L
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 18
VEAM PT Connectors
PT77SE Jam Nut Receptacle with External Rear Accessory Thread (Crimp Contacts Supplied Loose)
S
D
Q
P
V
H
U
N
Shell size
D
diameter
tolerance .003 (0.08)
K
Q
diameter
.017 (0.43)
V
depth
.031 (0.08)
U
length
max
S
diameter
max
H
panel thickness
min
max
K
rear diameter
max
P
jam nut
thread
N
rear access
thread
8
0.473
0.750
0.636
0.255
0.956
0.06
0.125
0.436
.5625-24 UNEF
.4375-28 UNEF
10
0.590
0.875
0.636
0.255
1.062
0.06
0.125
0.561
.6875-24 UNEF
.5625-24 UNEF
12
0.750
1.062
0.636
0.255
1.250
0.06
0.125
0.686
.8750-20 UNEF
.6875-24 UNEF
14
0.875
1.188
0.636
0.255
1.375
0.06
0.125
0.811
1.000-20 UNEF
.8125-20 UNEF
16
1.000
1.312
0.636
0.255
1.500
0.06
0.125
0.936
1.125-18 UNEF
.9375-20 UNEF
18
1.125
1.458
0.636
0.255
1.625
0.06
0.125
1.061
1.250-18 UNEF
1.0625-18 UNEF
20
1.250
1.562
0.794
0.275
1.812
0.06
0.250
1.186
1.375-18 UNEF
1.1875-18 UNEF
22
1.375
1.688
0.794
0.275
1.938
0.06
0.250
1.311
1.500-18 UNEF
1.3125-18 UNEF
24
1.500
1.812
0.812
0.275
2.062
0.06
0.250
1.436
1.625-18 UNEF
1.4375-18 UNEF
PT Jam Nut Accessories
PT77A
LBF
07A
PT07SE/77SE
LBF
GBF HBF
Z
No Thread
05-1778 Strain Relief Clamp
05-0120 SR and Grommet (see chart)
L
PT77A
05-0186 SR Clamp
PT07SE/77A
LP
LE
VEAM PT
GBF HBF
BE
DP
05-0114 External
Grommet Clamp Nut
BP
05-2042 Potting Boot
For dimensional data see accessories section on page’s 33 to 39.
Protective caps are located on page 33.
For connector supplied complete with relevant accessory please use
cross reference chart on page 43 or consult factory.
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-18
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 19
VEAM PT Connectors
How to Order Panel Mount Connectors
SERIES/
PREFIX
PT
SHELL
STYLE
SHELL SIZE/
LAYOUT
CONTACT
TYPE
polarization
CLASS
PLATING/
MOD CODE
NOTE 1
NOTE 1
NOTE 2
NOTE 3
NOTE 4
NOTE 5
(22-55)
S
P
(B)
(T69)
02
33
44
B
00
A
SE
obsolete
How To Order
1 Select the shell style and
classification eg. PT02A from following pages.
2 Add the shell size and contact arrangement
eg. PT02A22 55 see pages L-10 to L-13.
3 Add the contacts P=pins, S= sockets eg. PT02A22 55S.
4 For polarization add the relevant letter (E, B, C, F) or for orientation
add (W, X, Y, Z) from page 14. For normal orientation no letter required.
5 Add suffix as required from typical list below.
No Code
023
T69
T61
T21
T62/T65/T66
Olive drab cadmium plate finish as standard (historically 014)
Electroless Nickel plating finish
Zinc Cobalt Olive drab plate finish GB62
Zinc Cobalt Black plate finish (ROHS)
Marine ally Bronze (contact factory)
Pin tail contacts (contact factory)
Panel Mount Cut-Out Details
Front Mount
A
A
Rear Mount
E max. panel
thickness to
prevent interference
with rear fittings
C 4 holes
A
A
B
minimum adjacent piercing
t.p.
B Dia.
+.000
—.010
C Dia.
+.004
—.002
D
Min.
8
.594
.458
.120
10
.719
.583
.120
12
.812
.708
14
.906
.833
E
A
t.p.
C Dia.
+.004
—.002
8
.594
10
.719
.100
12
1.156
.100
14
Max.
Shell
Size
.843
.100
.969
.100
.120
1.062
.120
PTOO
Mounted from front
with rear fittings
PTOO
Mounted from rear
D
Min.
F Dia.
+.000
—.010
E
Max.
.120
.843
.580
.100
.120
.969
.700
.100
.812
.120
1.062
.859
.1000
.906
.120
1.156
.983
.100
16
.969
.958
.120
1.250
.100
16
.969
.120
1.250
1.108
.100
18
1.062
1.083
.120
1.343
.100
18
1.062
.120
1.343
1.233
.100
20
1.156
1.208
.120
1.469
.160
20
1.156
.120
1.469
1.359
.230
22
1.250
1.333
.120
1.593
.160
22
1.250
.120
1.593
1.493
.230
24
1.375
1.458
.147
1.718
.100
24
1.375
.147
1.718
1.614
.230
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-19
L
VEAM PT
A
B
D
D
minimum adjacent piercing
Shell
Size
C 4 holes
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 20
PT02 Box Mount Receptacle without rear accessory thread (solder contacts)
VEAM PT Connectors
PT02 Box Mount Receptacle without Rear Accessory Thread (Solder Contacts)
L
T holes
R
A
N
R
S
Z
K
Shell size
T dia
S
M
M
length
0.01
L
depth
0.825
N
rear diameter
0.01
R
hole space
tolerance
A
diameter
.003 (0.08)
S
width
0.016
T
hole diameter
0.005
8
0.473
0.431
0.825
0.449
0.594
0.812
0.120
10
0.590
0.431
0.825
0.573
0.719
0.938
0.120
12
0.750
0.431
0.825
0.699
0.812
1.031
0.120
14
0.875
0.431
0.825
0.823
0.906
1.125
0.120
16
1.000
0.431
0.825
0.949
0.969
1.219
0.120
18
1.125
0.431
0.825
1.073
1.062
1.312
0.120
20
1.250
0.556
1.076
1.199
1.156
1.438
0.120
22
1.375
0.556
1.076
1.323
1.250
1.562
0.120
24
1.500
0.589
1.109
1.449
1.375
1.688
0.147
PT33A Wall Mount Receptacle with External Rear Accessory Thread (Solder Contacts)
L
M
Z
POLARIZING
GROOVE
Q THD.
T DIA
4 MTG.
HOLES
A
DIA.
K
L
S
VEAM PT
SOLDER
Shell size
.140 RAD.
MAX.
R (TP)
M
length
0.01
L
depth
0.020
K
thickness
0.01
Z
length
0.04
KK
rear diameter
0.01
R
hole space
S
width
Q
thread
tolerance
A
diameter
.003 (0.08)
8
0.473
0.431
0.887
0.062
0.594
0.438
0.594
0.812
.4375-28 UNEF
10
0.590
0.431
0.887
0.062
0.394
0.562
0.719
0.938
.5625-24 UNEF
12
0.750
0.431
0.887
0.062
0.394
0.688
0.812
1.031
.6875-24 UNEF
14
0.875
0.431
0.887
0.062
0.394
0.812
0.906
1.125
.8125-20 UNEF
16
1.000
0.431
0.887
0.062
0.394
0.938
0.969
1.219
.9375-20 UNEF
18
1.125
0.431
0.887
0.062
0.394
1.062
1.062
1.312
1.0625-18 UNEF
20
1.250
0.556
1.105
0.094
0.455
1.188
1.156
1.438
1.1875-18 UNEF
22
1.375
0.556
1.105
0.094
0.455
1.312
1.250
1.562
1.3125-18 UNEF
24
1.500
0.589
1.105
0.094
0.422
1.438
1.375
1.688
1.4375-18 UNEF
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-20
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 21
VEAM PT Connectors
PT02SE Box Mount Receptacle without Rear Accessory Thread (Crimp Contacts)
L
POLARIZING
GROOVE
M
A
DIA.
T DIA
4 MTG.
HOLES
N
DIA.
R (TP)
K
.140 RAD.
MAX.
S
Shell size
tolerance
A
diameter
.003 (0.08)
M
length
0.01
L
depth
0.020
K
thickness
0.01
Z
length
0.04
N
rear diameter
0.01
R
hole space
S
width
8
0.473
0.431
0.825
0.062
0.594
0.469
0.594
0.828
10
0.590
0.431
0.825
0.062
0.394
0.593
0.719
0.954
12
0.750
0.431
0.825
0.062
0.394
0.719
0.812
1.047
14
0.875
0.431
0.825
0.062
0.394
0.843
0.906
1.141
16
1.000
0.431
0.825
0.062
0.394
0.969
0.969
1.234
18
1.125
0.431
0.825
0.062
0.394
1.093
1.062
1.328
20
1.250
0.556
1.011
0.094
0.455
1.219
1.156
1.453
22
1.375
0.556
1.011
0.094
0.455
1.343
1.250
1.578
24
1.500
0.589
1.011
0.094
0.422
1.469
1.375
1.702
PT33SE Receptacle with External Rear Accessory Thread (Crimp Contacts Supplied)
POLARIZING
GROOVE
K
Q THD.
M
GROMMET
FOR
TYPES
E&F
T DIA.
4 MTG.
HOLES
A
DIA.
CRIMP
tolerance
S
.140 RAD.
MAX.
A
diameter
.003 (0.08)
M
length
0.016
Z
length
0.04
N
rear diameter
0.01
Q
thread
S
width
R
hole space
8
0.473
0.431
0.948
0.469
.4375-28 UNEF
0.828
0.594
10
0.590
0.431
0.948
0.593
.5625-24 UNEF
0.954
0.719
12
0.750
0.431
0.948
0.719
.6875-24 UNEF
1.047
0.812
14
0.875
0.431
0.948
0.843
.8125-20 UNEF
1.141
0.906
16
1.000
0.431
0.948
0.969
.9375-20 UNEF
1.234
0.969
18
1.125
0.431
0.948
1.093
1.0625-18 UNEF
1.328
1.062
20
1.250
0.556
1.166
1.219
1.1875-18 UNEF
1.453
1.156
22
1.375
0.556
1.166
1.343
1.3125-18 UNEF
1.578
1.250
24
1.500
0.589
1.166
1.469
1.4375-18 UNEF
1.703
1.375
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-21
L
VEAM PT
shell size
R (TP)
GROMMET FOR
TYPES A, B, J & P
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 22
VEAM PT Connectors
PT44A Line Connecting Receptacle (no fixing holes) with Rear Accessory Thread Solder Contacts
L
Q
S
M
Y
A
S
K
Z
Shell size
tolerance
A
diameter
.003 (0.08)
M
length
0.016
Y
diameter
0.02
Z
length
0.04
N
rear diameter
0.01
Q
thread
S
width
8
0.473
0.400
0.938
0.948
0.469
.4375-28 UNEF
0.812
10
0.590
0.400
1.062
0.948
0.593
.5625-24 UNEF
0.938
12
0.750
0.400
1.156
0.948
0.719
.6875-24 UNEF
1.031
14
0.875
0.400
1.25
0.948
0.843
.8125-20 UNEF
1.125
16
1.000
0.400
1.344
0.948
0.969
.9375-20 UNEF
1.219
18
1.125
0.400
1.438
0.948
1.093
1.0625-18 UNEF
1.312
20
1.250
0.535
1.562
1.166
1.219
1.1875-18 UNEF
1.438
22
1.375
0.535
1.688
1.166
1.343
1.3125-18 UNEF
1.562
24
1.500
0.568
1.812
1.166
1.469
1.4375-18 UNEF
1.688
PT44SE Line Connecting Receptacle (no fixing holes) with Rear Accessory Thread (Crimp Contacts Supplied)
SEE TERMINATION
ASSEMBLY
H
P
Q THD.
POLARIZING
GROOVE
Y DIA.
A
DIA.
VEAM PT
L
GROMMET FOR
TYPES A, B, J & P
Shell size
CRIMP
GROMMET FOR
TYPES E & F
S
P
length
0.031
H
panel thickness
0.094
S
width
Y
diameter
Q
thread
tolerance
A
diameter
.003 (0.08)
8
0.473
0.400
0.094
0.828
0.958
.4375-28 UNEF
10
0.590
0.400
0.094
0.954
1.082
.5625-24 UNEF
12
0.750
0.400
0.094
1.047
1.176
.6875-24 UNEF
14
0.875
0.400
0.094
1.141
1.270
.8125-20 UNEF
16
1.000
0.400
0.094
1.234
1.364
.9375-20 UNEF
18
1.125
0.400
0.094
1.328
1.458
1.0625-18 UNEF
20
1.250
0.535
0.115
1.453
1.582
1.1875-18 UNEF
22
1.375
0.535
0.115
1.578
1.708
1.3125-18 UNEF
24
1.500
0.535
0.115
1.703
1.832
1.4375-18 UNEF
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-22
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 23
VEAM PT Connectors
PTB Thru Bulkhead Connector
T DIA.
4 MTG. HOLES
POLARIZING
GROOVE
L
PIN
SIDE
A
A
SKT
SIDE
M
R (TP)
K
shell size
A
diameter
.003 (0.08)
M
length
0.031
S
width
R
hole space
K
panel thickness
0.016
1.125
8
0.473
0.562
1.125
10
0.590
0.828
0.594
0.062
0.562
1.125
0.954
0.719
12
0.062
0.750
0.562
1.125
1.047
0.812
0.062
14
0.875
0.562
1.125
1.141
0.906
0.062
16
1.000
0.562
1.125
1.234
0.969
0.062
18
1.125
0.562
1.125
1.328
1.062
0.062
20
1.250
0.688
1.406
1.453
1.156
0.094
22
1.375
0.688
1.406
1.578
1.250
0.094
24
1.500
0.688
1.406
1.703
1.375
0.009
tolerance
L
.140 RAD.
MAX.
S TYP
This connector is a thru-bulkhead version with double
faced non-removable pin and socket insert construction allowing mating from both ends for applications
requiring the disconnection of a power source from
either side of a panel, or where air leakage requirements are critical.
Dummy Stowage Connector 05-0167-XX
N
T DIA.
4 MTG. HOLES
POLARIZING
GROOVE
To complete receptacle part number replace xx with shell size and add plating mod code from “How to Order” section on page 19.
R (TP)
Diameter
N
Depth
Oa
Mating
R
Thickness
8
0.473
0.493
0.300
0.080
10
0.590
0.493
0.300
0.080
12
0.750
0.493
0.300
0.080
14
0.875
0.493
0.300
0.080
16
1.000
0.493
0.300
0.080
18
1.125
0.493
0.300
0.080
20
1.250
0.587
0.360
0.110
22
1.375
0.587
0.360
0.110
24
1.500
0.620
0.360
0.110
Size
S TYP
R
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-23
VEAM PT
.140 RAD.
MAX.
0a
L
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 24
VEAM PT Connectors
Flange Mount Gaskets 05-0368-xx
S
D (4 HOLES)
S
R
F
8
Hole Diameter
D
0.13
Hole
to Hole
R
0.594
Width
S
0.812
Thick
T
0.031
10
0.13
0.719
0.958
0.031
12
0.13
0.813
1.031
0.031
14
0.13
0.906
1.123
0.031
16
0.13
0.969
1.219
0.031
18
0.13
1.065
1.312
0.031
20
0.13
1.156
1.438
0.031
22
0.13
1.250
1.565
0.031
24
0.13
1.373
1.658
0.031
Size
T
R
PT Panel Mount Accessories
02
PT33A/44A
LA
V THD
HBF
GBF
HBF
Type A
Z
05-1778 strain relief clamp
05-0120 SR and grommet
05-0532
adaptor
PT33A/44A
LE
PT33SE/44SE
PT33A/44A
BP
C
05-2042 potting boot
AF
AC
DP
L
05-0114 external grommet
clamp nut
05-0186 SR Clamp
LP
BE
VEAM PT
PT33SE/44SE
LBF
GBF
DA
.395
(10.03)
Min.
No Thread
PT33A/44A
LBF
D
05-2330 W sealing gland
For dimensional data see accessories section on page’s 33 to 39
Protective caps are located on page 33.
For connector supplied complete with relevant accessory please use
cross reference chart on page 43 or consult factory
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-24
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 25
VEAM PT Connectors
How to Order PT Plug Connectors
SERIES/
PREFIX
PT
SHELL
STYLE
SHELL SIZE/
LAYOUT
CONTACT
TYPE
polarization
CLASS
PLATING/
MOD CODE
NOTE 1
NOTE 1
NOTE 2
NOTE 3
NOTE 4
NOTE 5
55
A
(22-55)
S
(B)
(T69)
PTG
SE
P
How To Order
1 Select the shell style and
classification eg. PT55A from following pages.
2 Add the shell size and contact arrangement
eg. PT55A22 55 see pages L-10 to L-13.
3 Add the contacts P=pins, S= sockets eg. PT55A22 55S.
4 For polarization add the relevant letter (E, B, C, F) or for orientation
add (W, X, Y, Z) from page 14. For normal orientation no letter required.
5 Add suffix as required from typical list below.
No Code
O23
SR
T01
T02
T21
T62/T65/T66
T69
T61
Olive drab cadmium plate finish as standard (historically014)
Electroless Nickel plating finish
Ribbed coupling
Ribbed coupling nut
Ribbed coupling nut and strain relief
Marine ally Bronze (contact factory)
Pin tail contacts (contact factory)
Zinc cobalt olive drab plate finish
Zinc cobalt black plate finish (RoHS)
L
VEAM PT
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-25
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 26
VEAM PT Connectors
PT55A Straight Plug with Solder Contacts
L
Z
J
Shell
Size
G
Q
G
J
Z
L
Q
diameter
mate
depth
body
thread
tolerance
.003 (0.08)
0.01
8
.765
0.353
0.594
0.906
.4375-28 UNEF
10
.840
0.353
0.594
0.906
.5625-24 UNEF
12
.999
0.353
0.594
0.906
.6875-24 UNEF
14
1.139
0.353
0.594
0.906
.8125-20 UNEF
16
1.261
0.353
0.594
0.906
.9375-20 UNEF
18
1.337
0.353
0.594
0.906
1.0625-18 UNEF
20
1.477
0.415
0.672
1.062
1.1875-18 UNEF
22
1.602
0.415
0.672
1.062
1.3125-18 UNEF
24
1.723
0.415
0.672
1.125
1.4375-18 UNEF
PTG55A Straight Plug with Grounding Spring and Solder Contacts
L
J
Z
G
Q
L
VEAM PT
Shell
Size
G
J
Z
L
Q
diameter
mate
depth
body
thread
tolerance
.003 (0.08)
0.01
8
.765
0.353
0.594
0.906
.4375-28 UNEF
10
.840
0.353
0.594
0.906
.5625-24 UNEF
12
.999
0.353
0.594
0.906
.6875-24 UNEF
14
1.139
0.353
0.594
0.906
.8125-20 UNEF
16
1.261
0.353
0.594
0.906
.9375-20 UNEF
18
1.337
0.353
0.594
0.906
1.0625-18 UNEF
20
1.477
0.415
0.672
1.062
1.1875-18 UNEF
22
1.602
0.415
0.672
1.062
1.3125-18 UNEF
24
1.723
0.415
0.672
1.125
1.4375-18 UNEF
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-26
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 27
VEAM PT Connectors
PT55SE Straight Plug with Crimp Contacts
L
Q
J
Shell
Size
tolerance
G
G
J
L
Q
diameter
mate
depth
thread
.003 (0.08)
0.01
8
.765
0.353
1.900
.4375-28 UNEF
10
.859
0.353
1.900
.5625-24 UNEF
12
1.031
0.353
1.900
.6875-24 UNEF
14
1.156
0.353
1.900
.8125-20 UNEF
16
1.281
0.353
1.987
.9375-20 UNEF
18
1.391
0.353
1.987
1.0625-18 UNEF
20
1.531
0.415
2.087
1.1875-18 UNEF
22
1.656
0.415
2.087
1.3125-18 UNEF
24
1.776
0.415
2.149
1.4375-18 UNEF
PTG55SE Straight Plug with Grounding Fingers and Crimp Contacts
L
Q
J
G
L
G
J
L
Q
diameter
mate
depth
thread
tolerance
.003 (0.08)
0.01
8
.765
0.353
1.900
.4375-28 UNEF
10
.859
0.353
1.900
.5625-24 UNEF
12
1.031
0.353
1.900
.6875-24 UNEF
14
1.156
0.353
1.900
.8125-20 UNEF
16
1.281
0.353
1.987
.9375-20 UNEF
18
1.391
0.353
1.987
1.0625-18 UNEF
20
1.531
0.415
2.087
1.1875-18 UNEF
22
1.656
0.415
2.087
1.3125-18 UNEF
24
1.776
0.415
2.149
1.4375-18 UNEF
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-27
VEAM PT
Shell
Size
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 28
VEAM PT Connectors
PT55A (T01) Straight Plug with Ribbed Coupling Nut and Solder Contacts
A
H
F Thread
Om
E
Shell
Size
B
D
Om
H
F
diameter
coupling nut dia
mate
depth
thread
tolerance
.003 (0.08)
0.038
0.01
8
0.64
0.825
0.301
0.906
.4375-28 UNEF
10
0.756
0.937
0.301
0.906
.5625-24 UNEF
12
0.940
1.109
0.301
0.906
.6875-24 UNEF
14
1.063
1.234
0.301
0.906
.8125-20 UNEF
16
1.197
1.437
0.301
0.906
.9375-20 UNEF
18
1.308
1.548
0.301
0.906
1.0625-18 UNEF
20
1.430
1.67
0.301
1.062
1.1875-18 UNEF
22
1.565
1.78
0.341
1.062
1.3125-18 UNEF
24
1.678
1.905
0.341
1.125
1.4375-18 UNEF
PTG55A (T01) Straight Plug with Grounding Spring/Ribbed Coupling Nut and Solder Contacts
A
H
F Thread
Om
VEAM PT
L
E
Shell
Size
B
D
Om
H
F
diameter
coupling nut dia
mate
depth
thread
tolerance
.003 (0.08)
0.038
0.01
8
0.64
0.825
0.301
0.906
.4375-28 UNEF
10
0.756
0.937
0.301
0.906
.5625-24 UNEF
12
0.940
1.109
0.301
0.906
.6875-24 UNEF
14
1.063
1.234
0.301
0.906
.8125-20 UNEF
16
1.197
1.437
0.301
0.906
.9375-20 UNEF
18
1.308
1.548
0.301
0.906
1.0625-18 UNEF
20
1.430
1.67
0.301
1.062
1.1875-18 UNEF
22
1.565
1.78
0.341
1.062
1.3125-18 UNEF
24
1.678
1.905
0.341
1.125
1.4375-18 UNEF
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-28
ca_L1-L44.qxd:Layout 1
2/10/11
9:01 AM
Page 29
VEAM PT Connectors
PT55SE (T01) Straight Plug with Grounding Fingers / Ribbed Coupling Nut and Crimp Contacts
A
H
F Thread
Om
E
Shell
Size
B
D
Om
H
F
diameter
coupling nut dia
mate
depth
thread
tolerance
.003 (0.08)
0.038
0.01
8
0.765
0.825
0.353
1.900
.4375-28 UNEF
10
0.859
0.937
0.353
1.900
.5625-24 UNEF
12
1.031
1.109
0.353
1.900
.6875-24 UNEF
14
1.156
1.234
0.353
1.900
.8125-20 UNEF
16
1.281
1.437
0.353
1.978
.9375-20 UNEF
18
1.391
1.548
0.353
1.978
1.0625-18 UNEF
20
1.531
1.67
0.415
2.087
1.1875-18 UNEF
22
1.656
1.78
0.415
2.087
1.3125-18 UNEF
24
1.776
1.905
0.415
2.149
1.4375-18 UNEF
PTG55SE (T01) Straight Plug with Grounding Fingers / Ribbed Coupling Nut and Crimp Contacts
A
H
F Thread
Om
E
B
D
Om
H
F
diameter
coupling nut dia
mate
depth
thread
tolerance
.003 (0.08)
0.038
0.01
8
0.765
0.825
0.353
1.900
.4375-28 UNEF
10
0.859
0.937
0.353
1.900
.5625-24 UNEF
12
1.031
1.109
0.353
1.900
.6875-24 UNEF
14
1.156
1.234
0.353
1.900
.8125-20 UNEF
16
1.281
1.437
0.353
1.978
.9375-20 UNEF
18
1.391
1.548
0.353
1.978
1.0625-18 UNEF
20
1.531
1.67
0.415
2.087
1.1875-18 UNEF
22
1.656
1.78
0.415
2.087
1.3125-18 UNEF
24
1.776
1.905
0.415
2.149
1.4375-18 UNEF
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
www.ittcannon.com
L-29
VEAM PT
Shell
Size
L