MPM-12EPB Series Very Low Cost, 12W Compact “Power Brick” AC/DC Power Supplies Key Features: Electrical Specifications • 12W Output Power • Compact 1.1 x 2.1 Inch Case • Universal 85-264 VAC Input • EN 60950 Approved (UL) • Meets IEC Safety Class II • Industry Standard Pin-Out • Meets EN 55022 Class B • >300 kHour MTBF • Low, Low Cost Specifications typical @ +25°C, 230 VAC input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Conditions Min. Typ. 85 110 47 See Model Selection Guide 115 VAC 10.0 230 VAC 20.0 Max. 264 370 440 Conditions Min. Typ. See Model Selection Guide See Model Selection Guide ±2.0 VIN = Min to Max ±0.5 See Note 2 ±1.0 Max. Units 100 % % % mV P-P Input Voltage Range Input Frequency Input Current Inrush Current Units VAC VDC Hz A Pk Output Parameter Output Voltage Output Current Output Voltage Accuracy Line Regulation Load Regulation Ripple & Noise (20 MHz) 115 VAC 230 VAC 10 50 ±0.02 Continuous (Autorecovery) Zener Diode Clamp Autorecovery 110 Hold-Up Time Temperature Coefficient Short Circuit Protection Over Voltage Protection Overload Protection mSec %/°C %W General Parameter Isolation Voltage Isolation Resistance EMI Characteristics Parameter Radiated Emissions Conducted Emissions ESD RS EFT Surge CS PFMF Voltage Dips Switching Frequency Conditions Input to Output 500 VDC Standard See Note 4 EN 55022 EN 55022 EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-8 EN 61000-4-11 Min. 4,000 100 Typ. Min. Typ. Min. -40 Typ. +25 Max. Units VAC M Max. Units Class B Class B Criteria B; ±8 kV Air/±6 kV Contact Criteria A; 10V/m Criteria B; ±4 kV Criteria B; ±2 kV Criteria A; 10 Vrms Criteria A; 10A/m Criteria B; 0% - 70% 100 kHz Environmental MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions Max. +70 +90 -40 +105 Free Air Convection (See Derating Curve) RH, Non-condensing 95 Ambient Case Units °C °C °C % Physical Case Size Case Material Weight 2.12 x 1.13 x 0.925 Inches (53.8 x 28.8 x 23.50 mm) Non-Conductive Black Plastic (UL94-V0) 2.13 Oz (60g) Reliability Specifications Parameter MTBF Safety Standards Safety Class Conditions Min. Typ. MIL HDBK 217F, 25°C, Gnd Benign 300 EN 60950 IEC 60536 Class II www.micropowerdirect.com Max. Units kHours www.micropowerdirect.com Model Selection Guide Input Model Number Current (A) MPM-12S-03EPB MPM-12S-05EPB MPM-12S-12EPB MPM-12S-15EPB MPM-12S-24EPB 115 VAC 230 VAC 0.280 0.190 0.280 0.190 0.280 0.190 0.280 0.190 0.280 0.190 Typical Connection Output Standby Capacitive Efficiency Load Voltage Current Power (%, Typ) (W, Max) (µF Max.) (VDC) (A Max.) 3.3 5.0 12.0 15.0 24.0 2.400 2.400 1.000 0.800 0.500 0.3 0.3 0.3 0.3 0.3 10,000 10,000 5,400 2,700 1,500 74 78 82 82 83 Notes: 1. Operation at no load will not damage the units, however, they may not meet all specifications. 2. Load regulation is measured for an output change of 10% to 100% at nominal input line. 3. All units are rated for EN 55022 (CE/RE) class B without external components. 4. All units are rated for EN 61000-4-4 (±4 kV) and EN 61000-4-5 (±2 kV) without external components. They will meet EN 61000-4-5 (±4 kV/ ±6 kV) with additional input filtering as shown below. 5. It is recommended that a fuse be used on the input of a power supply for protection. For the MPM-12S-xxEPB series, a 3.15A/250 VAC slow blow should be used. The diagram below illustrates a typical application connection of the MPM-12EPB series. Notes on this circuit (starting with the input circuit) are: 1. It is recommended that an external fuse and NTC be used. The recommended fuse is a 3.15A/250V slow blow and for the NTC, a 5D-9. 2. An external MOV is required on the input to protect the unit in the event of a surge. A 561KD20 or equivalent is recommended. 3. Recommended output filtering capacitors are: C1 1.0 µF/50V 1.0 µF/50V 1.0 µF/50V 1.0 µF/50V 1.0 µF/50V MPM-12S-03EPB MPM-12S-05EPB MPM-12S-12EPB MPM-12S-15EPB MPM-12S-24EPB C2 220 µF/10V 220 µF/10V 120 µF/25V 120 µF/25V 68 µF/35V TVS SMBJ7.0A SMBJ7.0A SMBJ20A SMBJ20A SMBJ30A The output filtering capacitor (C2) is a high frequency, low resistance electrolytic capacitor. Capacitor (C1) is ceramic. Voltage derating of capacitors should be 80% or above. 4. Input noise and surge suppression modules are available for a number of MPD AC/DC power supplies. An MPM-12S-xxEPB connection with the ACFM-02 is illustrated in the diagram at left. For pricing or full technical information on these modules (ACFM-01 and ACFM-02) please contact the factory. Typical Connection: With ACFM-02 Input Module (See note 4) Pin Connections Derating Curve Pin Function Pin Function 1 2 AC-Neutral AC-Line 3 4 +Vo -Vo Mechanical Dimensions Input Voltage Vs Load Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) MicroPower Direct The MPM-20-xxEPB series is also available with a chassis mount or DIN mount adapter. Contact the factory for more information We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]