MDCFM-40U 40V-160VDC Input, Compact EMC Filter Module Key Features: • 40 to 110 VDC Input • Compact 1” x 2” Case • Meets EN 50155 Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Conditions • Reverse Polarity Protection • 1.2 MHour MTBF No Load Current, See Note 2 • -40°C to +85°C Operation General • 98% Efficiency Parameter • Low Cost Max. Units 160 VDC MDCFM-40U-10, MDCFM-40U-30 1.0 MDCFM-40U-50 3.0 Conditions Efficiency Typ. 40 • Chassis Mount Option • DIN Rail Mount Option Min. Input Voltage Range, See Note 1 Min. Typ. MDCFM-40U-10 95 MDCFM-40U-30, MDCFM-40U-50 98 Max Output Voltage mA Max. Units % 165 Max Output Power VDC MDCFM-40U-10 10 MDCFM-40U-30 30 MDCFM-40U-50 50 W EMI Characteristics (See Note 4) Parameter Standard Radiated Emissions Level EN 55022 Conducted Emissions Class B (150 kHz - 30 MHz) EN 55022 Class B (30 MHz - 1 GHz) ESD EN 61000-4-2 Criteria B; Air ±8 kV, Contact ±6 kV RS EN 61000-4-3 Criteria A; 10V/m EFT EN 61000-4-4 Surge EN 61000-4-5 CS EN 61000-4-6 Vibration EN 61373 Criteria B; ±4 kV (5 kHz - 100 kHz) Criteria B; ±2 kV (1.2 µS/50 µS 2⍀) Criteria B; ±4 kV (1.2 µS/50 µS 12⍀) Criteria B; 10 Vrms Sinusoidal 5~150 Hz; 7.5 mm Amplitude; 10g Acceleration Environmental Parameter Conditions Operating Temperature Range Ambient Storage Temperature Range MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Typ. Max. Units -40 +25 +85 °C +125 °C 95 % -55 Cooling Humidity Min. Free Air Convection RH, Non-condensing Physical Case Size Module See Mechanical Drawing (Page 2) Chassis (A2) Mount See Mechanical Drawing (Page 2) DIN (A4) Mount Case Material Weight See Mechanical Drawing (Page 2) Non-Conductive Black Plastic (UL94-V0) Module 1.77 Oz (50g) Chassis (A2) Mount 2.48 Oz (70g) DIN (A4) Mount 3.19 Oz (90g) www.micropowerdirect.com www.micropowerdirect.com Model Selection Guide Input Voltage Range (VDC) Model Number Withstand Voltage Max. Output Power Efficiency (%) Nominal Range MDCFM-40U-10 110 40 - 160 500 10 95% MDCFM-40U-30 110 40 - 160 500 30 98% MDCFM-40U-50 110 40 - 160 1,500 50 98% (VAC) Notes: 1. The Max input voltage level of the DC/DC converter must be less than the maximum specified input of the MDCFM-40U. 2. The maximum power of the DC/DC converter must be less than the maximum output power of the MDCFM-40. 3. The -VOUT pin should not be connected to the “ground” input. (W) Efficiency vs Input Voltage (Full Load) Typical Connection Efficiency vs Output Power (VIN= 110 VDC) The diagram at right shows a typical connection for a MDCFM-40U series filter module. Prawing at right i The external capacitors shown in the typical connection diagram below are required to meet specified operation. Recommended component values are given in the table below. Component C1 CY1, CY2 Value 400 µF/200V 1nF/2 kV The “GND” input should not be connected to the -VIN pin or the -VOUT pin of the filter. Also, the Y capacitors should be connected as shown, not from the filter module input to the DC/DC module output. 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected] www.micropowerdirect.com Mechanical Dimensions, MDCFM-40U-10 Pin Connections Pin 1 2 3 4 5 Function GND -VIN +VIN +VOUT -VOUT Mechanical Dimensions: With Chassis Mount Option (A2) The MDCFM-40U-10 is available mounted on an adapter plate for mounting to a chassis or on a DIN rail. Mechanical dimensions for these adapters is shown at right. The photo below shows a product mounted on a similar adapter. Please contact the factory for more information. For the chassis mount option, add suffix “A2” to the model number (i.e. MDCFM-40U-10-A2) For the DIN rail mount option, add suffix “A4” to the model number (i.e. MDCFM-40U-10-A4) Pin Connections Pin 1 2 3 4 5 Mechanical Dimensions: With DIN Rail Option (A4) Function GND -VIN +VIN +VOUT -VOUT Connection is the same for A2 & A4 Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) • Wire range for A2 & A4 connection is 24 - 12 AWG MicroPower Direct • 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected] Mechanical Dimensions, MDCFM-40U-30, MDCFM-40U-50 www.micropowerdirect.com Pin Connections Pin 1 2 3 4 5 Function GND -VIN +VIN +VOUT -VOUT Mechanical Dimensions: With Chassis Mount Option (A2) The MDCFM-40U-30/50 are available mounted on an adapter plate for mounting to a chassis or on a DIN rail. Mechanical dimensions for these adapters are shown at right. The photo below shows a product mounted on a similar adapter. Please contact the factory for more information. For the chassis mount option, add suffix “A2” to the model number (i.e. MDCFM-40U-30-A2) For the DIN rail mount option, add suffix “A4” to the model number (i.e. MDCFM-40U-50-A4) Pin Connections Pin 1 2 3 4 5 Mechanical Dimensions: With DIN Rail Option (A4) Function GND -VIN +VIN +VOUT -VOUT Connection is the same for A2 & A4 Notes: MicroPower Direct • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) • Wire range for A2 & A4 connection is 24 - 12 AWG We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]