MDCFM-03AW Datasheet

MDCFM-03AW
Wide Input, DC
Compact EMC
Filter Module
Key Features:
• 0 to 80 VDC Input
• Compact 1” x 1” Case
• 20 dB Attenuation
• -40°C to +85°C Operation
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Input Voltage Range, See Note 1
Nominal Current, See Note 2
DCR
• Chassis Mount Option
General
• DIN Rail Mount Option
Parameter
Frequency Attenuation
EFT
• Low Cost
Conditions
Min.
0.0
Typ.
Max.
80.0
3.0
Units
VDC
A
m⍀
Max.
Units
dB
30
Conditions
Min.
30
EN 61000-4-4
Typ.
Criteria B; ±4 kV
Environmental
Parameter
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Conditions
Min.
Typ.
-40
+25
-55
Free Air Convection
RH, Non-condensing
Ambient
Module
Chassis (A2) Mount
DIN (A4) Mount
Case Size
Case Material
Module
Chassis (A2) Mount
DIN (A4) Mount
Weight
Notes:
1. The Max input voltage level of the DC/DC converter
must be less than the maximum specified input of the
MDCFM-03AW.
2. The Max input current of the DC/DC converter must be
less than the maximum specified nominal current of the
MDCFM-03AW.
3. The -VOUT pin should not be connected to the “ground”
input.
Units
°C
°C
95
%
See Mechanical Drawing (Page 2)
See Mechanical Drawing (Page 2)
See Mechanical Drawing (Page 2)
Non-Conductive Black Plastic (UL94-V0)
0.71 Oz (20g)
1.41 Oz (40g)
2.11 Oz (60g)
Schematic: MDCFM-03AW
The MDCFM-03AW EMC filter module operate
with many standard MPD DC/DC converters.
When connected to the input, these modules
will substantially improve the EMS performance of the converter.
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Max.
+85
+125
Typical Connection
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
www.micropowerdirect.com
www.micropowerdirect.com
Mechanical Dimensions
Pin Connections
Pin
1
2
3
4
5
Function
+VIN
-VIN
GND
-VOUT
+VOUT
Mechanical Dimensions: With Chassis Mount Option (A2)
The MDCFM-03AW is available mounted on an adapter plate for mounting to a
chassis or on a DIN rail. Mechanical dimensions for these adapters is shown at right.
The photo below shows a product mounted on a similar adapter. Please contact the
factory for more information.
For the chassis mount option, add suffix “A2” to the
model number (i.e. MDCFM-03AW-A2)
For the DIN rail mount option, add suffix “A4” to the
model number (i.e. MDCFM-03AW-A4)
Mechanical Dimensions: With DIN Rail Option (A4)
Pin Connections
Pin
1
2
3
4
5
Function
+VIN
-VIN
GND
-VOUT
+VOUT
Connection is the
same for A2 & A4
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.02 (±0.50)
• Wire range for A2 & A4 connection is 24 - 12 AWG
FAX: (781) 344-8481
•
E-Mail: [email protected]