HD74LS161A Synchronous 4-bit Binary Counter (direct clear) REJ03D0445–0200 Rev.2.00 Feb.18.2005 This synchronous 4-bit binary counter features an internal carry look-ahead for application in high-speed counting designs. Synchronous operation is provided by having all flip-flops clocked simultaneously so that the outputs changes coincident with each other when so instructed by the count-enable inputs and internal gating. This mode is operation eliminates the output counting spikes that are normally associated with asynchronous (ripple clock) counters. A buffered clock input triggers the four flip-flops on the rising (positive-going) edge of the clock input waveform. This counter is fully programmable; that is, the output may be preset to either level. As presetting is synchronous, setting up a low level at the load input disables the counter and causes the outputs to agree with the setup data after the next clock pulse regardless of the levels of the enable inputs. Low-to-high transitions at the load input should be avoided when the clock is low if the enable inputs are high at or before the transition. The clear function is asynchronous and a low level at the clear input sets all four of the flip-flop outputs low regardless of the levels of clock, load, or enable inputs. The carry look-ahead circuitry provides for cascading counters for n-bit synchronous applications without additional getting. Instrumental in accomplishing this function are two count-enable inputs and a ripple carry output. Both count-enable inputs (P and T) must be high to count, and input T is fed forward to enable the ripple carry output. The ripple carry output thus enabled will produced a high-level output pulse with a duration approximately equal to the high-level portion of the QA output. This high-level overflow ripple carry pulse can be used to enable successive cascaded stages. High-to-low-level transitions at the enable P or T inputs should occur only when the clock input is high. Features • Ordering Information Part Name Package Type Package Code (Previous Code) Package Abbreviation Taping Abbreviation (Quantity) HD74LS161AP DILP-16 pin PRDP0016AE-B (DP-16FV) P — HD74LS161AFPEL SOP-16 pin (JEITA) PRSP0016DH-B (FP-16DAV) FP EL (2,000 pcs/reel) HD74LS161ARPEL SOP-16 pin (JEDEC) PRSP0016DG-A (FP-16DNV) RP EL (2,500 pcs/reel) Note: Please consult the sales office for the above package availability. Rev.2.00, Feb.18.2005, page 1 of 10 HD74LS161A Pin Arrangement Clear 1 CLR CK Ripple Carry 16 VCC 15 Ripple Carry Output Clock 2 A 3 A QA 14 QA B 4 B QB 13 QB C 5 C QC 12 QC D 6 D QD 11 QD Enable P 7 P T 10 Enable T GND 8 9 Load Data Inputs Outputs Load (Top view) Block Diagram Clock Clear Load Enable D Q CK Output QA Q CLR P T A D Q CK B Q CLR C D Q CK Q CLR D D Q CK Q CLR Data Inputs Output QB Output QC Output QD Ripple Carry Output Rev.2.00, Feb.18.2005, page 2 of 10 HD74LS161A Absolute Maximum Ratings Item Symbol Ratings Unit Supply voltage VCC 7 V Input voltage VIN 7 V Power dissipation PT 400 mW Tstg –65 to +150 °C Storage temperature Note: Voltage value, unless otherwise noted, are with respect to network ground terminal. Recommended Operating Conditions Item Symbol Min Typ Max Unit VCC 4.75 5.00 5.25 V IOH — — –400 µA IOL — — 8 mA Operating temperature Topr –20 25 75 °C Clock frequency ƒclock 0 — 25 MHz Clock pulse width tw (clock) 25 — — ns Clear pulse width tw (clear) 20 — — ns 20 — — ns 20 — — ns Supply voltage Output current A, B, C, D Setup time Enable P, T tsu Load Hold time th 20 — — ns 3 — — ns Typical Clear, Preset, and Inhibit Sequence Clear Load A Data Inputs B C D Clock Enable P Enable T QA QB Outputs QC QD Carry 12 Clear Rev.2.00, Feb.18.2005, page 3 of 10 Preset (Load) 13 14 15 0 Count 1 2 Inhibit HD74LS161A Electrical Characteristics (Ta = –20 to +75 °C) Item Input voltage Symbol VIH VIL min. 2.0 — typ.* — — max. — 0.8 Unit V V VOH 2.7 — — V IIH — — — — — — — — 0.4 0.5 20 40 µA VCC = 5.25 V, VI = 2.7 V IIL — — — — — — 20 –0.4 –0.8 mA VCC = 5.25 V, VI = 0.4 V II — — — — — –0.4 0.1 0.2 mA VCC = 5.25 V, VI = 7 V IOS ICCH — –20 — — — 18 0.1 –100 31 mA mA VCC = 5.25 V VCC = 5.25 V Output voltage VOL Input current Data, Enable P Load, Clock, Enable T Clear Data, Enable P Load, Clock, Enable T Clear Data, Enable P Load, Clock, Enable T Clear Short-circuit output current Supply current** V Condition VCC = 4.75 V, VIH = 2 V, VIL = 0.8 V, IOH = –400 µA IOL = 4 mA VCC = 4.75 V, VIH = 2 V, IOL = 8 mA VIL = 0.8 V ICCL — 19 32 mA VCC = 5.25 V Input clamp voltage VIK — — –1.5 V VCC = 4.75 V, IIN = –18 mA Notes: * VCC = 5 V, Ta = 25°C ** ICCH is measured with the load input high, then again with the load input low, with all other inputs high and all outputs open. ICCL is measured with the clock input high, then again with the clock input low, with all other inputs low and all outputs open. Switching Characteristics (VCC = 5 V, Ta = 25°C) Item Maximum clock frequency Propagation delay time Symbol ƒmax tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPHL Rev.2.00, Feb.18.2005, page 4 of 10 Inputs Clock Outputs QA to QD Clock Ripple Carry Clock (Load = “H”) QA to QD Clock (Load = “L”) QA to QD Enable T Ripple Carry Clear QA to QD min. 25 — — — — typ. 32 20 18 13 18 max. — 35 35 24 27 Unit MHz ns ns ns ns — — 13 18 24 27 ns ns — — — 9 9 20 14 14 28 ns ns ns Condition CL = 15 pF, RL = 2 kΩ HD74LS161A Timing Method tw (CK) 3V Clock 1.3V 1.3V 1.3V 0V tsu th 3V Load 1.3V 1.3V tsu Data Outputs A to D 0V th 3V 1.3V 1.3V 0V tsu Enable P or T 1.3V th 1.3V 0V Testing Method Test Circuit VCC QA 4.5V Load CK Input P.G. Zout = 50Ω See Testing Table P.G. Zout = 50Ω Load circuit 1 QA A B C D QB QB QC P T CLR 1. CL includes probe and jig capacitance. 2. All diodes are 1S2074(H). Rev.2.00, Feb.18.2005, page 5 of 10 RL CL Input Notes: 3V QC QD QD Ripple Carry Same as Load Circuit 1. Same as Load Circuit 1. Same as Load Circuit 1. Ripple Carry Same as Load Circuit 1. HD74LS161A Testing Table Item From input to output ƒmax tPLH tPHL CK Ripply → Carry CK → Q CK → Q Enable → T CLR → Q Ripple Carry Inputs Clear Load 4.5V Enable 4.5V P 4.5V T 4.5V 4.5V 4.5V 4.5V 4.5V 4.5V 4.5V GND 4.5V IN Clock Data IN A GND B GND C GND D GND 4.5V IN GND GND GND GND 4.5V GND 4.5V GND IN IN GND IN* GND IN* GND IN* GND IN* GND 4.5V IN IN* 4.5V 4.5V 4.5V 4.5V GND GND GND IN* 4.5V 4.5V 4.5V 4.5V Notes: *. For initialized Item From input to output QA QB QC QD Ripple Carry CK→Ripple Carry CK→Q CK→Q Enable T→Ripple Carry OUT — OUT OUT — OUT — OUT OUT — OUT — OUT OUT — OUT — OUT OUT — OUT OUT — — OUT CLR→Q OUT OUT OUT OUT — ƒmax tPLH tPHL Outputs Rev.2.00, Feb.18.2005, page 6 of 10 HD74LS161A Waveforms 1 ƒmax, tPLH, tPHL, (Clock→Q, Ripple Carry) tTLH Clock 10% tPLH QA tTHL 3V 90% 90% 1.3V 1.3V 10% (Measure at tn + 1) 1.3V tw (CK) 1.3V 0V tPHL (Measure at tn + 2) VOH 1.3V 1.3V tPHL tPLH (Measure at tn + 2) (Measure at tn + 4) QB 1.3V VOL VOH 1.3V VOL tPLH (Measure at tn + 4) tPHL (Measure at tn + 8) QC 1.3V VOH 1.3V VOL tPHL (Measure at tn + 16) QD tPLH (Measure at tn + 8) 1.3V VOH 1.3V VOL tPLH (Measure at tn + 15) Ripple Carry tPHL (Measure at tn + 16) VOH 1.3V 1.3V VOL Note: Clock input pulse; tTLH ≤ 15 ns, tTHL ≤ 6 ns, PRR = 1 MHz, duty cycle 50% and : ƒmax tTLH = tTHL ≤ 2.5 ns. tn is reference bit time when all outputs are low. Rev.2.00, Feb.18.2005, page 7 of 10 HD74LS161A Waveforms 2 tPLH, tPHL, (Clock→Q) tTLH tTHL 90% Clock 3V 90% 1.3V 10% tTLH 1.3V 10% 0V tTHL 90% Data Inputs A, B, C or D 3V 90% 10% 10% 0V tPLH tPHL VOH Outputs QA, QB, QC or QD 1.3V 1.3V VOL Note: Input pulse: tTLH ≤ 15 ns, tTHL ≤ 6 ns, Clock input: PRR = 1 MHz, duty cycle 50%, Data input: PRR = 500 kHz, duty cycle 50% Waveforms 3 tPLH, tPHL, (Enable T→Ripple Carry) tTLH tTHL 90 % 1.3 V Enable T 3V 90 % 1.3 V 10 % 10 % tPLH 0V tPHL VOH Carry Output Note: 1.3 V 1.3 V VOH Input pulse: tTLH ≤ 15 ns, tTHL ≤ 6 ns, PRR = 1 MHz Waveforms 4 tPHL, (Clear→Q) Clear tTHL tTLH 90% 1.3V 90% 1.3V 10% 10% tw (CLR) ≥ 20ns 3V 0V VOH QA to QD 1.3V tPHL Note: Input pulse: tTLH ≤ 15 ns, tTHL ≤ 6 ns Rev.2.00, Feb.18.2005, page 8 of 10 VOL HD74LS161A Package Dimensions JEITA Package Code P-DIP16-6.3x19.2-2.54 RENESAS Code PRDP0016AE-B MASS[Typ.] 1.05g Previous Code DP-16FV D 9 E 16 1 8 b3 0.89 Z A1 A Reference Symbol L e Nom θ c e1 D 19.2 E 6.3 JEITA Package Code P-SOP16-5.5x10.06-1.27 RENESAS Code PRSP0016DH-B *1 Previous Code FP-16DAV 7.4 A1 0.51 b p 0.40 b 3 0.48 0.56 1.30 c 0.19 θ 0° e 2.29 0.25 0.31 2.54 2.79 15° 1.12 L 2.54 MASS[Typ.] 0.24g NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. D F 16 20.32 5.06 Z ( Ni/Pd/Au plating ) Max 7.62 1 A bp e Dimension in Millimeters Min 9 c HE *2 E bp Index mark Reference Symbol Terminal cross section ( Ni/Pd/Au plating ) 1 Z *3 bp Nom D 10.06 E 5.50 Max 10.5 A2 8 e Dimension in Millimeters Min x A1 M 0.00 0.10 0.20 0.34 0.40 0.46 0.15 0.20 0.25 7.80 8.00 A L1 2.20 bp b1 c A c A1 θ y L Detail F 1 θ 0° HE 7.50 e 1.27 x 0.12 y 0.15 0.80 Z L L Rev.2.00, Feb.18.2005, page 9 of 10 8° 0.50 1 0.70 1.15 0.90 HD74LS161A JEITA Package Code P-SOP16-3.95x9.9-1.27 RENESAS Code PRSP0016DG-A *1 Previous Code FP-16DNV MASS[Typ.] 0.15g D NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. F 16 9 c *2 Index mark HE E bp Reference Symbol Terminal cross section ( Ni/Pd/Au plating ) Dimension in Millimeters Min Nom Max D 9.90 10.30 E 3.95 A2 8 1 Z e *3 bp x A1 0.10 0.14 0.25 0.34 0.40 0.46 0.15 0.20 0.25 6.10 6.20 1.75 A M L1 bp b1 c A c A1 θ L y Detail F 1 θ 0° HE 5.80 1.27 e x 0.25 y 0.15 0.635 Z 0.40 L L Rev.2.00, Feb.18.2005, page 10 of 10 8° 1 0.60 1.08 1.27 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. Unit2607 Ruijing Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 © 2005. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .2.0