19-4858; Rev 0; 8/09 EVALUATION KIT AVAILABLE +3.3V, Low-Jitter Crystal to LVPECL Clock Generator Features ♦ Crystal Oscillator Interface: 25MHz ♦ CMOS Input: 25MHz ♦ Output Frequencies for Ethernet 62.5MHz, 125MHz, 156.25MHz, 312.5MHz ♦ Low Jitter 0.14psRMS (1.875MHz to 20MHz) 0.36psRMS (12kHz to 20MHz) ♦ Excellent Power-Supply Noise Rejection ♦ No External Loop Filter Capacitor Required Applications Ordering Information Ethernet Networking Equipment Pin Configuration appears at end of data sheet. PART TEMP RANGE PIN-PACKAGE MAX3679AETJ+ -40°C to +85°C 32 TQFN-EP* +Denotes a lead(Pb)-free/RoHS-compliant package. *EP = Exposed pad. Typical Application Circuit +3.3V ±5% 0.1μF 10.5Ω VCC 10μF 0.1μF VCCO_A VCCO_B VCCA 0.1μF 0.1μF 0.01μF VDDO_A 0.1μF 36Ω Z0 = 50Ω QA_C ASIC 125MHz MR REF_IN IN_SEL QA Z0 = 50Ω QA Z0 = 50Ω ASIC 125MHz QAC_OE 50Ω 50Ω QA_OE QB0_OE VCC (VCC - 2V) QB1_OE MAX3679A BYPASS QB0 Z0 = 50Ω QB0 Z0 = 50Ω ASIC 312.5MHz SELA1 50Ω SELA0 50Ω SELB1 (VCC - 2V) SELB0 RES1 QB1 Z0 = 50Ω RES0 QB1 Z0 = 50Ω X_OUT X_IN GND 25MHz (CL = 18pF) 33pF GNDO_A ASIC 312.5MHz 50Ω 50Ω (VCC - 2V) 27pF ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX3679A General Description The MAX3679A is a low-jitter precision clock generator with the integration of three LVPECL and one LVCMOS outputs optimized for Ethernet applications. The device integrates a crystal oscillator and a phase-locked loop (PLL) clock multiplier to generate high-frequency clock outputs for Ethernet applications. This proprietary PLL design features ultra-low jitter (0.36psRMS) and excellent power-supply noise rejection, minimizing design risk for network equipment. MAX3679A +3.3V, Low-Jitter Crystal to LVPECL Clock Generator ABSOLUTE MAXIMUM RATINGS Voltage Range at GNDO_A...................................-0.3V to +0.3V Voltage Range at X_OUT ............................-0.3V to (VCC - 0.6V) Current into QA_C ...........................................................±50mA Current into QA, QA, QB0, QB0, QB1, QB1 .....................-56mA Continuous Power Dissipation (TA = +70°C) 32-Pin TQFN (derate 34.5mW/°C above +70°C) .......2759mW Operating Junction Temperature Range ...........-55°C to +150°C Storage Temperature Range .............................-65°C to +160°C Supply Voltage Range VCC, VCCA, VDDO_A, VCCO_A, VCCO_B ................................-0.3V to +4.0V Voltage Range at REF_IN, IN_SEL, SELA[1:0], SELB[1:0], RES[1:0], QAC_OE, QA_OE, QB0_OE, QB1_OE, MR, BYPASS ..........................................-0.3V to (VCC + 0.3V) Voltage Range at X_IN Pin ...................................-0.3V to +1.2V Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = +3.0V to +3.6V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VCC = +3.3V, TA = +25°C, unless otherwise noted.) (Notes 1, 2, and 3) PARAMETER Power-Supply Current SYMBOL ICC CONDITIONS MIN (Note 4) TYP MAX UNITS 77 100 mA CONTROL INPUT CHARACTERISTICS (SELA[1:0], SELB[1:0], IN_SEL, QAC_OE, QA_OE, QB1_OE, QB0_OE, MR, BYPASS Pins) Input Capacitance Input Pulldown Resistor Input Logic Bias Resistor Input Pullup Resistor CIN RPULLDOWN Pin MR RBIAS RPULLUP 2 pF 75 k Pins SELA[1:0], SELB[1:0], QB0_OE 50 k Pins QAC_OE, QA_OE, QB1_OE, IN_SEL, BYPASS 75 k LVPECL OUTPUT SPECIFICATIONS (QA, QA, QB0, QB0, QB1, QB1 Pins) Output High Voltage Output Low Voltage TA = 0°C to +85°C VCC 1.13 TA = -40°C to 0°C VCC 1.18 TA = 0°C to +85°C VCC 1.85 TA = -40°C to 0°C VCC 1.90 VOH VOL VCC 0.98 VCC 0.83 V VCC 0.83 VCC 1.7 VCC 1.55 V VCC 1.55 Peak-to-Peak Output-Voltage Swing (Single-Ended) (Note 2) 0.6 0.72 0.9 VP-P Clock Output Rise/Fall Time 20% to 80% (Note 2) 200 350 600 ps PLL enabled 48 50 52 PLL bypassed (Note 5) 40 50 60 Output Duty-Cycle Distortion % LVCMOS/LVTTL INPUT SPECIFICATIONS (SELA[1:0], SELB[1:0], IN_SEL, QAC_OE, QA_OE, QB1_OE, QB0_OE, MR, BYPASS Pins) Input-Voltage High VIH Input-Voltage Low VIL 2 2.0 _______________________________________________________________________________________ V 0.8 V +3.3V, Low-Jitter Crystal to LVPECL Clock Generator (VCC = +3.0V to +3.6V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VCC = +3.3V, TA = +25°C, unless otherwise noted.) (Notes 1, 2, and 3) PARAMETER SYMBOL CONDITIONS Input High Current I IH VIN = VCC Input Low Current I IL VIN = 0V MIN TYP MAX UNITS 80 μA -80 μA REF_IN SPECIFICATIONS (Input DC- or AC-Coupled) PLL enabled Reference Clock Frequency 25 PLL bypassed Input-Voltage High VIH Input-Voltage Low VIL Input High Current I IH VIN = VCC Input Low Current I IL VIN = 0V Reference Clock Duty Cycle 320 2.0 PLL enabled V 0.8 V 240 μA -240 μA 30 Input Capacitance MHz 70 2.5 % pF QA_C SPECIFICATIONS Output High Voltage VOH QA_C sourcing 12mA Output Low Voltage VOL QA_C sinking 12mA Output Rise/Fall Time Output Duty-Cycle Distortion 2.6 V 0.4 V ps (Notes 3, 6) 250 500 1000 PLL enabled 42 50 58 PLL bypassed (Note 5) 40 Output Impedance 60 % 14 CLOCK OUTPUT AC SPECIFICATIONS VCO Frequency Range Random Jitter (Note 7) Deterministic Jitter Due to Supply Noise Spurs Induced by Power-Supply Noise (Notes 7, 9, 10) 625 RJRMS 12kHz to 20MHz 0.36 1.875MHz to 20MHz 0.14 LVPECL output (Notes 7, 8, 9) 5.0 LVPECL output -59 LVCMOS output -47 Nonharmonic and Subharmonic Spurs Output Skew Clock Output SSB Phase Noise at 125MHz (Note 11) Note 1: -70 Between QB0 and QB1 15 Between QA and QB0 or QB1, PECL outputs 20 f = 1kHz -124 f = 10kHz -125 f = 100kHz -130 f = 1MHz -145 f > 10MHz -153 MHz 1.0 psRMS psP-P dBc dBc ps dBc/Hz A series resistor of up to 10.5Ω is allowed between VCC and VCCA for filtering supply noise when system power-supply tolerance is VCC = 3.3V ±5%. See Figure 2. _______________________________________________________________________________________ 3 MAX3679A ELECTRICAL CHARACTERISTICS (continued) MAX3679A +3.3V, Low-Jitter Crystal to LVPECL Clock Generator ELECTRICAL CHARACTERISTICS (continued) (VCC = +3.0V to +3.6V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VCC = +3.3V, TA = +25°C, unless otherwise noted.) (Notes 1, 2, and 3) Guaranteed up to 320MHz for LVPECL output. Guaranteed up to 160MHz for LVCMOS output. All outputs enabled and unloaded. IN_SEL set high. Measured with crystal or AC-coupled, 50% duty-cycle signal on REF_IN. Measured using setup shown in Figure 1 with VCC = 3.3V ±5%. Measured with crystal source. Total TIE including random and deterministic jitter. Measured with Agilent DSO81304A 40GS/s real-time oscilloscope using 2M sample record length. Note 9: Measured with 40mVP-P, 100kHz sinusoidal signal on the supply. Note 10: Measured at 156.25MHz output. Note 11: Measured with 25MHz crystal or 25MHz reference clock at LVCMOS input with a slew rate of 0.5V/ns or greater. Note 2: Note 3: Note 4: Note 5: Note 6: Note 7: Note 8: 36Ω MAX3679A 499Ω OSCILLOSCOPE 0.1μF Z0 = 50Ω QA_C 4.7pF 50Ω Figure 1. LVCMOS Output Measurement Setup 4 _______________________________________________________________________________________ +3.3V, Low-Jitter Crystal to LVPECL Clock Generator SUPPLY CURRENT vs. TEMPERATURE DIFFERENTIAL OUTPUT WAVEFORM AT 156.25MHz (LVPECL OUTPUT) MAX3679A toc03 MAX3679A toc02 MAX3679A toc01 250 175 ALL OUTPUTS ACTIVE AND TERMINATED 150 125 100 ALL OUTPUTS ACTIVE AND UNTERMINATED 75 AMPLITUDE (50mV/div) 200 MEASURED USING 50Ω OSCILLOSCOPE INPUT THROUGH NETWORK SHOWN IN FIGURE 1 AMPLITUDE (200mV/div) 225 50 25 0 -15 10 35 60 85 1ns/div 1ns/div AMBIENT TEMPERATURE (°C) PHASE NOISE AT 312.5MHz CLOCK FREQUENCY -100 -110 -120 -130 -140 -150 MAX3679A toc05 -90 -80 NOISE POWER DENSITY (dBc/Hz) -80 PHASE NOISE AT 125MHz CLOCK FREQUENCY MAX3679A toc04 -90 -100 -110 -120 -130 -140 -150 -160 -160 1 10 100 1000 10,000 100,000 0.1 OFFSET FREQUENCY (kHz) 1 10 100 1000 10,000 100,000 OFFSET FREQUENCY (kHz) JITTER HISTOGRAM (312.5MHz OUTPUT, 40mVP-P SUPPLY NOISE AT 100kHz) NOISE SPUR AMPLITUDE vs. NOISE FREQUENCY MAX3679A toc06 0 fC = 156.25MHz NOISE AMPLITUDE = 40mVP-P -10 DJ = 5.0psP-P -20 MAX3679A toc07 0.1 SPUR AMPLITUDE (dBc) -40 NOISE POWER DENSITY (dBc/Hz) SUPPLY CURRENT (mA) OUTPUT WAVEFORM AT 125MHz (LVCMOS OUTPUT) -30 -40 -50 -60 -70 -80 -90 10 5ps/div 100 1000 10,000 NOISE FREQUENCY (kHz) _______________________________________________________________________________________ 5 MAX3679A Typical Operating Characteristics (Typical values are at VCC = +3.3V, TA = +25°C, crystal frequency = 25MHz.) +3.3V, Low-Jitter Crystal to LVPECL Clock Generator MAX3679A Pin Description 6 PIN NAME 1 VCCO_B FUNCTION 2, 19, 24 GND 3 QB0_OE LVCMOS/LVTTL Input. Enables/disables QB0 clock output. Connect pin high to enable LVPECL clock output QB0. Connect low to set QB0 to a logic 0. Has internal 50k input impedance. 4, 5 SELB1, SELB0 LVCMOS/LVTTL Input. Controls NB divider setting. Has 50k input impedance. See Table 2 for more information. 6 QAC_OE LVCMOS/LVTTL Input. Enables/disables QA_C clock output. Connect pin high to enable QA_C. Connect low to set QA_C to a high-impedance state. Has internal 75k pullup to VCC. 7 MR LVCMOS/LVTTL Input. Master reset input. Pulse high for > 1μs to reset all dividers. Has internal 75k pulldown to GND. Not required for normal operation. 8 GNDO_A 9 QA_C 10 VDDO_A Power Supply for QA_C Clock Output. Connect to +3.3V. 11 VCCO_A Power Supply for QA Clock Output. Connect to +3.3V. 12 QA Noninverting Clock Output, LVPECL 13 QA Inverting Clock Output, LVPECL 14 BYPASS 15 RES1 Not Internally Connected. Connect to GND, VCC, or leave open for normal operation. 16 RES0 Reserved for Test. Connect to GND for normal operation. 17 VCCA Analog Power Supply for the VCO. Connect to +3.3V. For additional power-supply noise filtering, this pin can connect to VCC through 10.5 as shown in Figure 2 (requires VCC = +3.3V ±5%). 18 VCC Core Power Supply. Connect to +3.3V. 20 QA_OE LVCMOS/LVTTL Input. Enables/disables the QA clock output. Connect this pin high to enable the LVPECL clock output QA. Connect low to set QA to a logic 0. Has internal 75k pullup to VCC. 21, 22 SELA0, SELA1 LVCMOS/LVTTL Input. Controls NA divider setting. See Table 2 for more information. Has 50k input impedance. 23 QB1_OE LVCMOS/LVTTL Input. Enables/disables QB1 clock output. Connect pin high to enable LVPECL clock output QB1. Connect low to set QB1 to a logic 0. Has internal 50k input impedance. 25 X_OUT 26 X_IN 27 REF_IN LVCMOS Reference Clock Input. Self-biased to allow AC- or DC-coupling. 28 IN_SEL LVCMOS/LVTTL Input. Connect high or leave open to use a crystal. Connect low to use REF_IN. Has internal 75k pullup to VCC. 29 QB1 LVPECL, Inverting Clock Output 30 QB1 LVPECL, Noninverting Clock Output 31 QB0 LVPECL, Inverting Clock Output 32 QB0 LVPECL, Noninverting Clock Output — EP Power Supply for QB0 and QB1 Clock Outputs. Connect to +3.3V. Supply Ground Ground for QA_C Output. Connect to supply ground. LVCMOS Clock Output LVCMOS/LVTTL Input (Active Low). Connect low to bypass the internal PLL. Connect high for normal operation. When in bypass mode the output dividers are set to divide by 1. Has internal 75k pullup to VCC. Crystal Oscillator Output Crystal Oscillator Input Exposed Pad. Connect to supply ground for proper electrical and thermal performance. _______________________________________________________________________________________ +3.3V, Low-Jitter Crystal to LVPECL Clock Generator The MAX3679A is a low-jitter clock generator designed to operate at Ethernet frequencies. It consists of an onchip crystal oscillator, PLL, programmable dividers, LVCMOS output buffer, and LVPECL output buffers. Using a low-frequency clock (crystal or CMOS input) as a reference, the internal PLL generates a high-frequency output clock with excellent jitter performance. Crystal Oscillator An integrated oscillator provides the low-frequency reference clock for the PLL. This oscillator requires an external crystal connected between X_IN and X_OUT. Crystal frequency is 25MHz. REF_IN Buffer An LVCMOS-compatible clock source can be connected to REF_IN to serve as the reference clock. The LVCMOS REF_IN buffer is internally biased to allow AC- or DC-coupling. It is designed to operate up to 320MHz. PLL The PLL takes the signal from the crystal oscillator or reference clock input and synthesizes a low-jitter, highfrequency clock. The PLL contains a phase-frequency detector (PFD), a lowpass filter, and a 625MHz voltagecontrolled oscillator (VCO). The VCO output is connected to the PFD input through a feedback divider. The PFD compares the reference frequency to the divideddown VCO output (fVCO/25) and generates a control signal that keeps the VCO locked to the reference clock. The high-frequency VCO output clock is sent to the output dividers. To minimize noise-induced jitter, the VCO supply (VCCA) is isolated from the core logic and output buffer supplies. LVCMOS Driver QA_C, the LVCMOS output, is designed to drive a single-ended high-impedance load. The maximum operating frequency is specified up to 160MHz. This output can be disabled by the QAC_OE pin if not used and goes to a high impedance when disabled. Reset Logic/POR During power-on, the power-on reset (POR) signal is generated to synchronize all dividers. An external master reset (MR) signal is not required. Applications Information Power-Supply Filtering The MAX3679A is a mixed analog/digital IC. The PLL contains analog circuitry susceptible to random noise. In addition to excellent on-chip power-supply noise rejection, the MAX3679A provides a separate powersupply pin, VCCA, for the VCO circuitry. Figure 2 illustrates the recommended power-supply filter network for V CCA . The purpose of this design technique is to ensure clean input power supply to the VCO circuitry and to improve the overall immunity to power-supply noise. This network requires that the power supply is +3.3V ±5%. Decoupling capacitors should be used on all other supply pins for best performance. Output Divider Configuration Table 2 shows the input settings required to set the output dividers. Leakage in the OPEN case must be less than 1µA. Note that when the MAX3679A is in bypass mode (BYPASS set low), the output dividers are automatically set to divide by 1. Output Dividers The output divider is programmable to allow a range of output frequencies. See Table 2 for the divider input settings. The output dividers are automatically set to divide by 1 when the MAX3679A is in bypass mode (BYPASS = 0). +3.3V ±5% VCC 0.1μF 10.5Ω VCCA LVPECL Drivers The high-frequency outputs—QA, QB0, and QB1—are differential PECL buffers designed to drive transmission lines terminated with 50Ω to VCC - 2.0V. The maximum operating frequency is specified up to 320MHz. Each output can be individually disabled, if not used. The outputs go to a logic 0 when disabled. 0.1μF 10μF Figure 2. Analog Supply Filtering _______________________________________________________________________________________ 7 MAX3679A Detailed Description MAX3679A +3.3V, Low-Jitter Crystal to LVPECL Clock Generator Table 1. Output Frequency Determination XO OR CMOS INPUT FREQUENCY (MHz) FEEDBACK DIVIDER, M 25 25 VCO FREQUENCY (MHz) 625 Table 2. Output Divider Configuration SELA0/SELB0 0 0 1 0 0 OUTPUT FREQUENCY (MHz) ÷2 312.5 ÷4 156.25 ÷5 125 ÷10 62.5 1 OPEN NA/NB DIVIDER APPLICATIONS Ethernet Table 3. Crystal Selection Parameters PARAMETER INPUT SELA1/SELB1 1 OUTPUT DIVIDER, NA AND NB SYMBOL MIN TYP f OSC 25 ÷2* Crystal Oscillation Frequency ÷4 Shunt Capacitance CO 2.0 ÷5 Load Capacitance CL 18 ÷10 Equivalent Series Resistance (ESR) RS *Maximum guaranteed output frequency is 160MHz for CMOS and 320MHz for LVPECL output. Maximum Crystal Drive Level MAX UNITS MHz 7.0 pF pF 50 300 μW 27pF X_IN 25MHz CRYSTAL (CL = 18pF) X_OUT 33pF Figure 4. Crystal, Capacitors Connection Crystal Input Layout and Frequency Stability Figure 3. Crystal Layout Crystal Selection The crystal oscillator is designed to drive a fundamental mode, AT-cut crystal resonator. See Table 3 for recommended crystal specifications. See Figure 4 for external capacitance connection. 8 The crystal, trace, and two external capacitors should be placed on the board as close as possible to the MAX3679A’s X_IN and X_OUT pins to reduce crosstalk of active signals into the oscillator. The layout shown in Figure 3 gives approximately 3pF of trace plus footprint capacitors per side of the crystal (Y1). The dielectric material is FR4 and dielectric thickness of the reference board is 15 mils. Using a 25MHz crystal and the capacitor values of C22 = 27pF and C23 = 33pF, the measured output frequency accuracy is -14ppm at +25°C ambient temperature. _______________________________________________________________________________________ +3.3V, Low-Jitter Crystal to LVPECL Clock Generator Interface Models +3.3V 130Ω termination methods can be used such as shown in Figures 5 and 6. Unused outputs should be disabled and can be left open. For more information on LVPECL terminations and how to interface with other logic families, refer to Application Note 291: HFAN-01.0: Introduction to LVDS, PECL, and CML. Figures 7, 8, and 9 show examples of interface models. 130Ω VCC MAX3679A Qx Z0 = 50Ω Qx Z0 = 50Ω HIGH IMPEDANCE 82Ω 82Ω Qx Figure 5. Thevenin Equivalent of Standard PECL Termination Qx 0.1μF Z0 = 50Ω Qx 100Ω MAX3679A 0.1μF HIGH IMPEDANCE ESD STRUCTURES Z0 = 50Ω Qx 150Ω 150Ω Figure 8. Simplified LVPECL Output Circuit Schematic NOTE: AC-COUPLING IS OPTIONAL. Figure 6. AC-Coupled PECL Termination VDDO_A VCC DISABLE VB = 1.4V VCC 10Ω VB IN QA_C 14.5kΩ 10Ω VB REF_IN ESD STRUCTURES ESD STRUCTURES Figure 7. Simplified REF_IN Pin Circuit Schematic Figure 9. Simplified LVCMOS Output Circuit Schematic _______________________________________________________________________________________ 9 MAX3679A Interfacing with LVPECL Outputs The equivalent LVPECL output circuit is given in Figure 8. These outputs are designed to drive a pair of 50Ω transmission lines terminated with 50Ω to VTT = VCC - 2V. If a separate termination voltage (VTT) is not available, other Pin Configuration Exposed-Pad Package The exposed pad on the 32-pin TQFN package provides a very low inductance path for return current traveling to the PCB ground plane. The pad is also electrical ground on the MAX3679A and must be soldered to the circuit board ground for proper electrical performance. 10 QB1 IN_SEL REF_IN X_IN X_OUT 31 QB1 32 30 29 28 27 26 25 1 SELB0 5 QAC_OE 6 MR 7 GNDO_A 8 MAX3679A *EP 9 10 11 12 13 14 15 16 RES0 4 RES1 SELB1 BYPASS 3 QA QB0_OE QA 2 VCCO_A GND + VDDO_A VCCO_B QB0 TOP VIEW QB0 Layout Considerations The inputs and outputs are critical paths for the MAX3679A, and care should be taken to minimize discontinuities on these transmission line. Here are some suggestions for maximizing the MAX3679A’s performance: • An uninterrupted ground plane should be positioned beneath the clock I/Os. • Ground pin vias should be placed close to the IC and the input/output interfaces to allow a return current path to the MAX3679A and the receive devices. • Supply decoupling capacitors should be placed close to the MAX3679A supply pins. • Maintain 100Ω differential (or 50Ω single-ended) transmission line impedance out of the MAX3679A. • Use good high-frequency layout techniques and a multilayer board with an uninterrupted ground plane to minimize EMI and crosstalk. Refer to the MAX3679A Evaluation Kit for more information. QA_C MAX3679A +3.3V, Low-Jitter Crystal to LVPECL Clock Generator 24 GND 23 QB1_OE 22 SELA1 21 SELA0 20 QA_OE 19 GND 18 VCC 17 VCCA THIN QFN (5mm × 5mm) *EXPOSED PAD CONNECTED TO GROUND. Chip Information TRANSISTOR COUNT: 10,780 PROCESS: BiCMOS ______________________________________________________________________________________ +3.3V, Low-Jitter Crystal to LVPECL Clock Generator BYPASS IN_SEL SELA[1:0] QAC_OE LVCMOS BUFFER QA_C DIVIDER NA QA_OE QA LVPECL BUFFER PFD 27pF FILTER VCO QB1_OE 1 CRYSTAL OSCILLATOR X_OUT QB1 LVPECL BUFFER 1 X_IN 25MHz 625MHz 0 REF_IN QA 0 LVCMOS QB1 DIVIDER NB ÷25 QB0_OE 33pF DIVIDERS: NA = 2, 4, 5, 10 NB = 2, 4, 5, 10 QB0 LVPECL BUFFER QB0 MAX3679A SELB[1:0] Package Information For the latest package outline information and land patterns, go to www.microsemi.com.. PACKAGE TYPE PACKAGE CODE DOCUMENT NO. 32 TQFN-EP T3255+3 21-0140 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 11 © 2009 Maxim Integrated Products 11 Maxim is a registered trademark of Maxim Integrated Products, Inc. MAX3679A Block Diagram Microsemi Corporation (NASDAQ: MSCC) offers a comprehensive portfolio of semiconductor solutions for: aerospace, defense and security; enterprise and communications; and industrial and alternative energy markets. Products include high-performance, high-reliability analog and RF devices, mixed signal and RF integrated circuits, customizable SoCs, FPGAs, and complete subsystems. Microsemi is headquartered in Aliso Viejo, Calif. Learn more at www.microsemi.com. Microsemi Corporate Headquarters One Enterprise, Aliso Viejo CA 92656 USA Within the USA: +1 (949) 380-6100 Sales: +1 (949) 380-6136 Fax: +1 (949) 215-4996 © 2012 Microsemi Corporation. All rights reserved. Microsemi and the Microsemi logo are trademarks of Microsemi Corporation. All other trademarks and service marks are the property of their respective owners.