CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LE Radial Lead Type, Ultra-low ESR series Ultra-low ESR, High ripple current. Load life of 2000 hours at 105°C. Radial lead type : Lead free flow soldering condition correspondence Compliant to the RoHS directive (2002/95/EC). LF LE Low ESR Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 2.5 to 6.3V Rated Capacitance Range 470 to 1500µF ± 20% at 120Hz, 20°C Capacitance Tolerance Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( Less than or equal to the specified value at 100kHz, 20°C 1) Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C Z– 55°C / Z+20°C Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Resistance to Soldering Heat After soldering the capacitor under the soldering conditions prescribed here as preheat at 150 to 200°C for 60 to 180 seconds and peak temperature at 265°C for 10 seconds or less, the capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing the soldering side. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value Marking Navy blue print on the case top 1.25 1.25 (100kHz) 1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Type numbering system (Example : 4V 560µF) Dimensions Resin coated Case Capacitance 1 Silvered lead Wire P ±0.5 φD+0.5 MAX. LE 560 g 841 Lot. No. 3 4 5 6 7 8 9 10 11 12 Size code Configuration Capacitance toleranc (±20%) φd Series 2 P L E 0 G 5 6 1 MCO 1 Voltage(g:4V) Rated capacitance (560µF) L+0.5MAX. 15MIN 4MIN Rated voltage (4V) Series name (mm) Size φD L P φd φ8 × 9L 8.0 8.5 3.5 0.6 φ8 × 12L 8.0 11.5 3.5 0.6 φ10 × 13L 10.0 12.5 5.0 0.6 Type Voltage V 2.5 4 6.3 Code e g j Please refer to page 20 about the end seal configulation. Dimension table in next page. CAT.8100Z CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LE series Standard Ratings Rated Voltage Surge Voltage (V) (V) Code 2.5 (0E) 4 (0G) 6.3 (0J) 2.8 4.6 7.2 Case Size φD × L (mm) tan δ Leakage Current (µA) ESR (mΩ) (at 100kHz 20°C) Rated Ripple (mArms) 560 8×9 0.08 280 5 6100 PLE0E561MCO1 820 8×9 0.08 410 5 6300 PLE0E821MCO6 Rated Capacitance (µF) Part Number 820 8 × 12 0.08 410 5 6600 PLE0E821MDO1 1000 10 × 13 0.08 500 5 7100 PLE0E102MDO1 1500 10 × 13 0.08 750 5 7300 PLE0E152MDO1 560 8×9 0.08 448 5 6000 PLE0G561MCO1 680 8 × 12 0.08 544 5 6500 PLE0G681MDO1 820 10 × 13 0.08 656 5 7000 PLE0G821MDO1 1200 10 × 13 0.08 960 5 7200 PLE0G122MDO1 470 8 × 12 0.08 592 5 6400 PLE0J471MDO1 680 10 × 13 0.08 857 5 6700 PLE0J681MDO1 820 10 × 13 0.08 1033 5 6800 PLE0J821MDO1 Rated ripple current (mArms) at 105°C 100kHz No marked, 1 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system. Taping specifications are given in page 20, 21, 22. Please refer to page 3 for the minimum order quantity. CAT.8100Z