PCG0G222MCL1GS

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CG
Chip Type, Higher Capacitance
series
Higher Capacitance, Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at
260°C peak correspondence.
Compliant to the RoHS directive (2011/65/EU).
CG
Higher
Capacitance
CF
Specifications
Item
Performance Characteristics
Category Temperature Range
– 55 to +105°C
Rated Voltage Range
2.5 to 16V
Rated Capacitance Range
47 to 4700µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
Less than or equal to the specified value.
1.25
1.25
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
(100kHz)
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Resistance to
Soldering Heat
Marking
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 6.3V 470µF)
1
0.5 MAX.
2
3
4
5
6
7
8
9 10 11 12 13 14
PCG 0 J 4 7 1 MC L 1 GS
Taping code
A±0.2
C±0.2
B±0.2
φD±0.5
CG
470
j
841
Lot No.
E
Capacitance
Positive
Plastic platform
0.3 MAX.
Configuration
Capacitance tolerance (±20%)
Series
L +0.1
-0.4
Voltage ( j:6.3v)
Rated capacitance (470µF)
Negative
Rated voltage (6.3V)
H
Size
φD
L
A
B
C
E
H
φ5 × 6L
5.0
φ6.3 × 6L
6.3
φ8 × 7L
8.0
5.9
5.9
6.9
7.9
9.9
12.6
6.0
7.3
9.0
11.0
11.0
11.0
5.3
6.6
8.3
10.3
10.3
10.3
5.3
6.6
8.3
10.3
10.3
10.3
1.6
2.1
3.2
4.6
4.6
4.6
0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
Dimension table in next page.
Series name
(mm)
φ10 × 8L φ10 × 10L φ10 × 12.7L
10.0
10.0
10.0
Type
Voltage
V
2.5
4
6.3
10
16
Code
e
g
j
A
C
CAT.8100D
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CG
Standard Ratings
series
Rated Voltage
(V)(code)
2.5
(0E)
4
(0G)
6.3
(0J)
10
(1A)
Surge Voltage
(V)
2.8
4.6
7.2
11.5
Rated Capacitance
(µF)
Case Size
φD × L (mm)
tan δ
Leakage Current
(µA)
ESR (mΩ)
(at 100kHz 20°C)
Rated Ripple
(mArms)
Part Number
220
5×6
0.12
110
30
2100
PCG0E221MCL1GS
330
5×6
0.12
500
30
2200
PCG0E331MCL1GS
330
5×6
0.12
500
10
3300
PCG0E331MCO1GS
470
6.3 × 6
0.12
235
20
2900
PCG0E471MCL1GS
560
6.3 × 6
0.12
280
20
3000
PCG0E561MCL1GS
820
8×7
0.12
410
20
3300
PCG0E821MCL1GS
1500
10 × 8
0.12
750
17
4100
PCG0E152MCL1GS
2700
10 × 10
0.12
1350
12
4700
PCG0E272MCL1GS
3300
10 × 12.7
0.12
1650
10
5500
PCG0E332MCL1GS
4700
10 × 12.7
0.12
2350
10
5600
PCG0E472MCL1GS
PCG0G181MCL1GS
180
5×6
0.12
144
32
1900
220
5×6
0.12
300
32
2000
PCG0G221MCL1GS
220
5×6
0.12
300
15
2900
PCG0G221MCO1GS
390
6.3 × 6
0.12
312
22
2700
PCG0G391MCL1GS
680
8×7
0.12
544
21
3200
PCG0G681MCL1GS
1200
10 × 8
0.12
960
17
4000
PCG0G122MCL1GS
2200
10 × 10
0.12
1760
13
4600
PCG0G222MCL1GS
2700
10 × 12.7
0.12
2160
11
5300
PCG0G272MCL1GS
3300
10 × 12.7
0.12
2640
11
5400
PCG0G332MCL1GS
PCG0J151MCL1GS
150
5×6
0.12
189
33
1800
180
5×6
0.12
500
33
1900
PCG0J181MCL1GS
180
5×6
0.12
500
17
3000
PCG0J181MCO1GS
270
6.3 × 6
0.12
340
23
2600
PCG0J271MCL1GS
330
6.3 × 6
0.12
416
23
2700
PCG0J331MCL1GS
470
8×7
0.12
592
22
3100
PCG0J471MCL1GS
1000
10 × 8
0.12
1260
18
3800
PCG0J102MCL1GS
1800
10 × 10
0.12
2268
14
4400
PCG0J182MCL1GS
2200
10 × 12.7
0.12
2772
12
5000
PCG0J222MCL1GS
2700
10 × 12.7
0.12
3402
12
5100
PCG0J272MCL1GS
82
5×6
0.12
164
35
1700
PCG1A820MCL1GS
100
5×6
0.12
250
35
1800
PCG1A101MCL1GS
150
6.3 × 6
0.12
300
25
2500
PCG1A151MCL1GS
180
6.3 × 6
0.12
360
25
2600
PCG1A181MCL1GS
330
8×7
0.12
660
23
3100
PCG1A331MCL1GS
560
10 × 8
0.12
1120
20
3600
PCG1A561MCL1GS
10 × 10
0.12
1640
15
4300
PCG1A821MCL1GS
1000
10 × 12.7
0.12
2000
13
4800
PCG1A102MCL1GS
1500
10 × 12.7
0.12
3000
13
4900
PCG1A152MCL1GS
820
16
(1C)
18.4
47
5×6
0.12
150
40
1500
PCG1C470MCL1GS
56
5×6
0.12
240
40
1600
PCG1C560MCL1GS
82
6.3 × 6
0.12
262
30
2300
PCG1C820MCL1GS
100
6.3 × 6
0.12
320
30
2400
PCG1C101MCL1GS
150
8×7
0.12
480
28
2800
PCG1C151MCL1GS
270
10 × 8
0.12
864
25
3300
PCG1C271MCL1GS
470
10 × 10
0.12
1504
20
3700
PCG1C471MCL1GS
680
10 × 12.7
0.12
2176
18
4100
PCG1C681MCL1GS
820
10 × 12.7
0.12
2624
18
4200
PCG1C821MCL1GS
Rated ripple current (mArms) at 105°C 100kHz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please refer to page 3 for the minimum order quantity.
CAT.8100D