conductive polymer aluminum solid electrolytic capacitors

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Chip Type, Standard
CF
series
Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at 260°C
peak correspondence.
Compliant to the RoHS directive (2011/65/EU).
CS
CG
Higher
Capacitance,
CF
Long Life
Low ESR
Higher Capacitance
CJ
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C
Rated Voltage Range
2.5 to 25V
Rated Capacitance Range
3.3 to 1500μF
Capacitance Tolerance
± 20%
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
at 120Hz, 20°C
Less than or equal to the specified value.
2)
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1.25
1.25
(100kHz)
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed
at right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface
shall not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall
be two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall
be once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Resistance to
Soldering Heat
Marking
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 6.3V 150μF)
Positive
Lot No.
1
C±0.2
2
3
4
5
6
7
8
Taping code
9 10 11 12 13 14
Code
qD
PC F 0 J 1 5 1 MC L 1 GS
0.5 MAX.
Capacitance
Plastic platform
0.3 MAX.
4 to 6.3(5.5L)
GB
5 to 10(L
GS
6)
A±0.2
E
B±0.2
qD±0.5
CF
150
j
841
Size code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (150μF)
L +0.1
-0.4
Voltage ( j:6.3v)
Series
Negative
Rated voltage (6.3V)
H
Series name
Type
Size
qD
L
A
B
C
E
H
q4 =5.5L
4.0
q5 =6L
5.0
q6.3 =5.5L q6.3 =6L
6.3
6.3
5.4
5.9
5.4
5.0
6.0
7.3
4.3
5.3
4.3
5.3
(mm)
q10 =8L q10 =10L q10 =12.7L
10.0
10.0
10.0
q8 =7L
8.0
q8 =12L
8.0
5.9
6.9
11.9
7.9
9.9
12.6
7.3
9.0
9.0
11.0
11.0
11.0
6.6
6.6
8.3
8.3
10.3
10.3
10.3
6.6
6.6
8.3
8.3
10.3
10.3
10.3
1.0
1.6
2.1
3.2
3.2
4.6
4.6
2.1
4.6
0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
Dimension table in next page.
Voltage
V
2.5
4
6.3
10
16
20
25
Code
e
g
j
A
C
D
E
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CF
series
Standard Ratings
Rated Voltage
(V)(code)
2.5
(0E)
Surge Voltage
(V)
2.8
Rated Capacitance
(μF)
Case Size
φD × L (mm)
tan δ
100
6.3 × 6
0.12
220
6.3 × 5.5
0.12
220
6.3 × 6
470
820
ESR (mΩ)
(at 100kHz 20°C)
Rated Ripple
(mArms)
Part Number
100
22
2600
PCF0E101MCL1GS
110
20
2800
PCF0E221MCL4GB
0.12
110
20
2800
PCF0E221MCL1GS
8×7
0.12
235
20
3300
PCF0E471MCL1GS
10 × 8
0.12
410
17
4400
PCF0E821MCL1GS
1500
10 × 10
0.12
750
13
4700
PCF0E152MCL1GS
1500
10 × 12.7
0.12
750
12
5440
PCF0E152MCL9GS
4 × 5.5
0.12
100
200
700
PCF0G330MCL1GB
100
6.3 × 5.5
0.12
100
22
2600
PCF0G101MCL4GB
100
6.3 × 6
0.12
80
22
2600
PCF0G101MCL1GS
150
6.3 × 5.5
0.12
120
22
2800
PCF0G151MCL4GB
150
5×6
0.12
300
30
2000
PCF0G151MCL6GS
150
6.3 × 6
0.12
120
22
2800
PCF0G151MCL1GS
220
8×7
0.12
176
21
3200
PCF0G221MCL1GS
330
8×7
0.12
264
21
3400
PCF0G331MCL1GS
470
10 × 8
0.12
376
17
4200
PCF0G471MCL1GS
0.12
448
13
4520
PCF0G561MCL4GS
33
4
(0G)
4.6
560
680
10 × 8
0.12
544
17
4400
PCF0G681MCL1GS
820
10 × 10
0.12
656
13
4800
PCF0G821MCL1GS
10 × 12.7
0.12
960
10
5500
PCF0G122MCL1GS
22
4 × 5.5
0.12
100
200
700
PCF0J220MCL1GB
47
5×6
0.12
148
35
1600
PCF0J470MCL1GS
82
6.3 × 5.5
0.12
103
23
2600
PCF0J820MCL4GB
82
6.3 × 6
0.12
103
23
2600
PCF0J820MCL1GS
100
6.3 × 5.5
0.12
126
23
2800
PCF0J101MCL4GB
100
5×6
0.12
315
25
2200
PCF0J101MCL6GS
100
6.3 × 6
0.12
126
23
2800
PCF0J101MCL1GS
120
6.3 × 6
0.12
151
23
3000
PCF0J121MCL1GS
150
8×7
0.12
189
22
3200
PCF0J151MCL1GS
220
8×7
0.12
277
22
3400
PCF0J221MCL1GS
330
10 × 8
0.12
416
18
4200
PCF0J331MCL1GS
0.12
592
12
5300
PCF0J471MCL4GS
1200
6.3
(0J)
7.2
470
10
(1A)
11.5
8 × 12
Leakage Current
(μA)
8 × 12
470
10 × 8
0.12
592
18
4300
PCF0J471MCL6GS
470
10 × 10
0.12
592
16
4600
PCF0J471MCL1GS
680
10 × 10
0.12
857
14
5000
PCF0J681MCL1GS
680
10 × 12.7
0.12
857
10
5500
PCF0J681MCL9GS
820
10 × 12.7
0.12
1033
10
5800
PCF0J821MCL1GS
4.7
4 × 5.5
0.12
100
240
670
PCF1A4R7MCL1GB
6.8
4 × 5.5
0.12
100
240
670
PCF1A6R8MCL1GB
10
4 × 5.5
0.12
100
220
700
PCF1A100MCL1GB
15
4 × 5.5
0.12
100
200
700
PCF1A150MCL1GB
33
5×6
0.12
165
35
1500
PCF1A330MCL1GS
47
5×6
0.12
235
26
2600
PCF1A470MCL6GS
47
6.3 × 6
0.12
94
26
2600
PCF1A470MCL1GS
56
6.3 × 5.5
0.12
112
25
2500
PCF1A560MCL4GB
56
6.3 × 6
0.12
112
25
2500
PCF1A560MCL1GS
120
8×7
0.12
240
23
3000
PCF1A121MCL1GS
150
8×7
0.12
300
23
3200
PCF1A151MCL6GS
150
10 × 8
0.12
300
21
3300
PCF1A151MCL1GS
0.12
540
13
4500
PCF1A271MCL4GS
0.12
540
20
3600
PCF1A271MCL1GS
0.12
660
14
4000
PCF1A331MCL4GS
270
270
330
8 × 12
10 × 8
8 × 12
330
10 × 8
0.12
660
20
3700
PCF1A331MCL1GS
470
10 × 10
0.12
940
16
4600
PCF1A471MCL1GS
470
10 × 12.7
0.12
940
12
5300
PCF1A471MCL9GS
560
10 × 10
0.12
1120
15
4800
PCF1A561MCL1GS
560
10 × 12.7
0.12
1120
13
5230
PCF1A561MCL9GS
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CF
series
Standard Ratings
Rated Voltage
(V)(code)
Surge Voltage
(V)
Rated Capacitance
(μF)
18.4
23
28.7
ESR (mΩ)
(at 100kHz 20°C)
Rated Ripple
(mArms)
Part Number
0.12
100
260
660
PCF1C3R3MCL1GB
5×6
0.12
176
45
1210
PCF1C220MCL1GS
33
6.3 × 6
0.12
106
31
2400
PCF1C330MCL1GS
39
6.3 × 5.5
0.12
125
31
2400
PCF1C390MCL4GB
39
6.3 × 6
0.12
125
31
2400
PCF1C390MCL1GS
56
8×7
0.12
179
30
2900
PCF1C560MCL1GS
82
8×7
0.12
262
28
3200
PCF1C820MCL1GS
100
10 × 8
0.12
320
27
3300
PCF1C101MCL1GS
150
10 × 8
0.12
480
25
3500
PCF1C151MCL1GS
0.12
576
16
4400
PCF1C181MCL4GS
8 × 12
180
10 × 8
0.12
576
25
3600
PCF1C181MCL1GS
220
10 × 10
0.12
704
20
3900
PCF1C221MCL1GS
220
10 × 12.7
0.12
704
14
5050
PCF1C221MCL9GS
330
10 × 12.7
0.12
1056
14
5000
PCF1C331MCL1GS
10
5×6
0.12
100
120
900
PCF1D100MCL1GS
22
6.3 × 5.5
0.12
100
50
1700
PCF1D220MCL4GB
22
6.3 × 6
0.12
88
50
1700
PCF1D220MCL1GS
39
8×7
0.12
156
45
2000
PCF1D390MCL1GS
47
8×7
0.12
188
45
2000
PCF1D470MCL1GS
56
10 × 8
0.12
224
40
2400
PCF1D560MCL1GS
68
10 × 8
0.12
272
40
2600
PCF1D680MCL1GS
82
10 × 8
0.12
328
40
2600
PCF1D820MCL1GS
100
8 × 12
0.12
400
22
3200
PCF1D101MCL1GS
120
10 × 10
0.12
480
35
2800
PCF1D121MCL1GS
150
10 × 12.7
0.12
600
20
4320
PCF1D151MCL1GS
6.3 × 6
0.12
85
80
1200
PCF1E6R8MCL1GS
10
8×7
0.12
125
60
1600
PCF1E100MCL1GS
22
10 × 8
0.12
275
50
2200
PCF1E220MCL1GS
6.8
25
(1E)
Leakage Current
(μA)
4 × 5.5
180
20
(1D)
tan δ
22
3.3
16
(1C)
Case Size
φD × L (mm)
33
8 × 12
0.12
413
30
2800
PCF1E330MCL1GS
47
8 × 12
0.12
588
30
3000
PCF1E470MCL4GS
47
10 × 10
0.12
588
45
2400
PCF1E470MCL1GS
56
10 × 12.7
0.12
700
28
3800
PCF1E560MCL1GS
Rated ripple current (mArms) at 105°C 100kHz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please refer to page 3 for the minimum order quantity.
No marked, 1
: In this case,
: In this case,
: In this case,
will be put at 12th digit of type numbering system.
4 will be put at 12th digit of type numbering system.
6 will be put at 12th digit of type numbering system.
9 will be put at 12th digit of type numbering system.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CJ
Chip Type, Low ESR,
Higher Capacitance
series
CK
Low ESR, Higher Capacitance, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at
260°C peak correspondence.
Compliant to the RoHS directive (2011/65/EU).
Low ESR
CJ
Low ESR
Higher
Capacitance,
CF
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C
Rated Voltage Range
2.5 to 16V
Rated Capacitance Range
33 to 2700μF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
Less than or equal to the specified value .
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1.25
1.25
(100kHz)
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Resistance to
Soldering Heat
Marking
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Type numbering system (Example : 6.3V 220μF)
Dimensions
1
Positive
0.5 MAX.
C±0.2
3
4
5
6
7
8
9 10 11 12 13 14
Taping code
Size code
B ±0.2
Capacitance tolerance (±20%)
Rated capacitance (220μF)
Rated voltage (6.3V)
L +0.1
-0.4
Voltage ( j:6.3v)
A±0.2
Configuration
qD±0.5
CJ
220
j
841
Series
Plastic platform
0.3 MAX.
Lot No.
E
Capacitance
2
PC J 0 J 2 2 1 MC L 1 GS
Negative
Series name
H
Type
Size
qD
L
A
B
C
E
H
q5 =6L
5.0
q6.3 =6L q6.3 =8L
6.3
6.3
q8 =7L
8.0
q8 =8L
8.0
q8 =10L
8.0
q8 =12L
8.0
(mm)
q10 =8L q10 =10L q10 =12.7L
10.0
10.0
10.0
5.9
5.9
7.9
6.9
7.9
9.9
11.9
7.9
9.9
12.6
6.0
7.3
7.3
9.0
9.0
9.0
9.0
11.0
11.0
11.0
5.3
5.3
6.6
6.6
6.6
6.6
8.3
8.3
8.3
8.3
8.3
8.3
8.3
8.3
10.3
10.3
10.3
10.3
10.3
10.3
1.6
2.1
2.1
3.2
3.2
3.2
3.2
4.6
4.6
4.6
0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
Dimension table in next page.
Voltage
V
2.5
4
6.3
10
16
Code
e
g
j
A
C
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CJ
Standard Ratings
series
Rated Voltage
(V)(code)
Surge Voltage
(V)
2.5
(0E)
2.8
4
(0G)
4.6
6.3
(0J)
7.2
10
(1A)
11.5
16
(1C)
18.4
Rated Capacitance
(μF)
180
390
470
560
560
680
820
820
1000
1200
1500
1500
2200
2700
100
150
270
330
390
470
560
560
680
1000
1000
1200
1200
1500
1500
1800
1800
2200
100
120
220
270
330
330
390
470
820
820
820
1200
1500
1500
1800
47
56
68
120
150
220
270
330
390
470
680
33
39
68
82
100
100
120
150
180
220
220
270
330
Case Size
φD × L (mm)
5
6.3
6.3
6.3
8
8
8
8
8
10
8
8
10
10
5
5
6.3
6.3
6.3
8
8
8
8
8
10
8
10
8
10
10
10
10
5
5
6.3
6.3
6.3
8
8
8
8
8
10
10
10
10
10
5
5
5
6.3
6.3
8
8
8
8
10
10
5
5
6.3
6.3
6.3
8
8
8
8
8
10
8
10
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
6
6
8
8
7
7
8
12
8
8
10
12
10
12.7
6
6
6
6
8
7
7
12
8
10
8
12
10
12
10
10
12.7
12.7
6
6
6
8
8
7
7
8
10
12
8
10
10
12.7
12.7
6
6
6
6
8
7
7
8
10
8
10
6
6
6
8
8
7
7
8
10
10
8
12
10
tan δ
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
Leakage Current
(μA)
90
195
235
280
280
340
410
410
500
600
750
750
1100
1350
80
120
216
264
312
376
448
448
544
800
800
960
960
1200
1200
1440
1440
1760
126
151
277
340
416
416
491
592
1033
1033
1033
1512
1890
1890
2268
94
112
136
240
300
440
540
660
780
940
1360
105
125
217
262
320
320
384
480
576
704
704
864
1056
ESR (mΩ)
(at 100kHz 20°C)
Rated Ripple
(mArms)
Part Number
21
15
13
13
13
13
12
9
12
13
10
9
10
9
22
22
15
15
14
14
14
9
13
10
13
9
10
9
10
10
9
9
24
24
15
14
14
14
14
13
12
10
13
12
12
10
11
28
28
28
25
21
21
21
19
17
19
13
35
35
28
24
24
24
24
22
18
18
22
16
16
2670
3400
3600
3600
4100
4100
4260
5400
4260
4800
5220
5400
5500
5800
2610
2610
3200
3300
3470
3950
4000
5200
3950
5220
4300
5400
5500
5200
5500
5500
5600
5700
2500
2500
3200
3470
3470
3950
3950
3950
4770
5150
4500
5025
5025
5500
5200
2310
2310
2310
2530
2880
3220
3220
3390
4000
3800
4820
2070
2070
2390
2700
2700
3010
3010
3150
3890
3890
3450
4070
4350
PCJ0E181MCL1GS
PCJ0E391MCL1GS
PCJ0E471MCL1GS
PCJ0E561MCL4GS
PCJ0E561MCL1GS
PCJ0E681MCL1GS
PCJ0E821MCL6GS
PCJ0E821MCL1GS
PCJ0E102MCL1GS
PCJ0E122MCL1GS
PCJ0E152MCL6GS
PCJ0E152MCL1GS
PCJ0E222MCL1GS
PCJ0E272MCL1GS
PCJ0G101MCL1GS
PCJ0G151MCL1GS
PCJ0G271MCL1GS
PCJ0G331MCL1GS
PCJ0G391MCL1GS
PCJ0G471MCL1GS
PCJ0G561MCL1GS
PCJ0G561MCL9GS
PCJ0G681MCL1GS
PCJ0G102MCL4GS
PCJ0G102MCL1GS
PCJ0G122MCL1GS
PCJ0G122MCL6GS
PCJ0G152MCL4GS
PCJ0G152MCL1GS
PCJ0G182MCL1GS
PCJ0G182MCL9GS
PCJ0G222MCL1GS
PCJ0J101MCL1GS
PCJ0J121MCL1GS
PCJ0J221MCL1GS
PCJ0J271MCL1GS
PCJ0J331MCL4GS
PCJ0J331MCL1GS
PCJ0J391MCL1GS
PCJ0J471MCL1GS
PCJ0J821MCL6GS
PCJ0J821MCL4GS
PCJ0J821MCL1GS
PCJ0J122MCL1GS
PCJ0J152MCL1GS
PCJ0J152MCL9GS
PCJ0J182MCL1GS
PCJ1A470MCL1GS
PCJ1A560MCL1GS
PCJ1A680MCL1GS
PCJ1A121MCL1GS
PCJ1A151MCL1GS
PCJ1A221MCL1GS
PCJ1A271MCL1GS
PCJ1A331MCL1GS
PCJ1A391MCL1GS
PCJ1A471MCL1GS
PCJ1A681MCL1GS
PCJ1C330MCL1GS
PCJ1C390MCL1GS
PCJ1C680MCL1GS
PCJ1C820MCL1GS
PCJ1C101MCL4GS
PCJ1C101MCL1GS
PCJ1C121MCL1GS
PCJ1C151MCL1GS
PCJ1C181MCL1GS
PCJ1C221MCL4GS
PCJ1C221MCL1GS
PCJ1C271MCL1GS
PCJ1C331MCL1GS
Rated ripple current (mArms) at 105°C 100kHz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please refer to page 3 for the minimum order quantity.
No marked, 1
: In this case,
: In this case,
: In this case,
will be put at 12th digit of type numbering system.
4 will be put at 12th digit of type numbering system.
6 will be put at 12th digit of type numbering system.
9 will be put at 12th digit of type numbering system.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CK
Chip Type, Ultra-low ESR
series
Ultra-low ESR, Higher Capacitance, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at 260°C peak
correspondence.
Compliant to the RoHS directive (2011/65/EU).
CJ
CK
Low ESR
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C
Rated Voltage Range
2.5 to 6.3V
Rated Capacitance Range
220 to 2200μF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
1)
ESR (
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current (
2)
Less than or equal to the specified value .
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1.25
1.25
(100kHz)
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Resistance to
Soldering Heat
Marking
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
1
0.5 MAX.
2
3
4
5
6
7
8
9 10 11 12 13 14
PCK 0 J 2 2 1 MCO 1 GS
Taping code
A±0.2
C±0.2
B ±0.2
qD±0.5
CK
220
j
941
Lot No.
E
Capacitance
Type numbering system (Example : 6.3V 220μF)
Positive
Plastic platform
0.3 MAX.
Configuration
Capacitance tolerance (±20%)
Series
L +0.1
-0.4
Voltage ( j:6.3v)
Negative
Rated capacitance (220μF)
Rated voltage (6.3V)
H
Series name
Size
qD
L
A
B
C
E
H
Type
(mm)
q10 =8L q10 =10L
10.0
10.0
q6.3 =6L
6.3
q8 =7L
8.0
5.9
6.9
7.9
9.9
7.3
6.6
9.0
8.3
11.0
10.3
11.0
10.3
6.6
8.3
10.3
10.3
2.1
3.2
4.6
4.6
0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
Dimension table in next page.
Voltage
V
2.5
4
6.3
Code
e
g
j
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CK
series
Standard Ratings
Rated Voltage
(V)(code)
2.5
(0E)
4
(0G)
6.3
(0J)
Surge Voltage
(V)
2.8
4.6
7.2
Rated Capacitance
(μF)
Case Size
φD × L (mm)
tan δ
Leakage Current
(μA)
ESR (mΩ)
(at 100kHz 20°C)
Rated Ripple
(mArms)
Part Number
390
6.3 × 6
0.12
293
10
3900
PCK0E391MCO1GS
560
8×7
0.12
420
9
4500
PCK0E561MCO1GS
680
8×7
0.12
510
9
4500
PCK0E681MCO1GS
1200
10 × 8
0.12
900
9
5000
PCK0E122MCO1GS
2200
10 × 10
0.12
1650
8
6000
PCK0E222MCO1GS
330
6.3 × 6
0.12
396
10
3900
PCK0G331MCO1GS
470
8×7
0.12
564
9
4500
PCK0G471MCO1GS
560
8×7
0.12
672
9
4500
PCK0G561MCO1GS
1000
10 × 8
0.12
1200
9
5000
PCK0G102MCO1GS
1800
10 × 10
0.12
2160
8
6000
PCK0G182MCO1GS
220
6.3 × 6
0.12
416
10
3900
PCK0J221MCO1GS
330
8×7
0.12
624
9
4500
PCK0J331MCO1GS
390
8×7
0.12
737
9
4500
PCK0J391MCO1GS
820
10 × 8
0.12
1550
9
5000
PCK0J821MCO1GS
10 × 10
0.12
2835
8
6000
PCK0J152MCO1GS
1500
Rated ripple current (mArms) at 105°C 100kHz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please refer to page 3 for the minimum order quantity.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Chip Type, Higher Capacitance
CG
series
Higher Capacitance, Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at
260°C peak correspondence.
Compliant to the RoHS directive (2011/65/EU).
CG
Higher
Capacitance
CF
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C
Rated Voltage Range
2.5 to 16V
Rated Capacitance Range
47 to 4700μF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
1)
ESR (
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current (
2)
Less than or equal to the specified value.
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1.25
1.25
(100kHz)
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Resistance to
Soldering Heat
Marking
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 6.3V 470μF)
1
0.5 MAX.
2
3
4
5
6
7
8
9 10 11 12 13 14
PCG 0 J 4 7 1 MC L 1 GS
Taping code
A±0.2
C±0.2
B ±0.2
qD±0.5
CG
470
j
841
Lot No.
E
Capacitance
Positive
Plastic platform
0.3 MAX.
Configuration
Capacitance tolerance (±20%)
Series
L +0.1
-0.4
Voltage ( j:6.3v)
Rated capacitance (470μF)
Negative
Rated voltage (6.3V)
H
Size
qD
L
q5 =6L
5.0
q6.3 =6L
6.3
q8 =7L
8.0
5.9
5.9
6.9
7.9
9.9
12.6
A
B
C
6.0
7.3
9.0
11.0
11.0
11.0
5.3
6.6
8.3
10.3
10.3
10.3
5.3
6.6
8.3
10.3
10.3
10.3
E
H
1.6
2.1
3.2
4.6
4.6
4.6
0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
Dimension table in next page.
Series name
(mm)
q10 =8L q10 =10L q10 =12.7L
10.0
10.0
10.0
Type
Voltage
V
2.5
4
6.3
10
16
Code
e
g
j
A
C
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CG
Standard Ratings
series
Rated Voltage
(V)(code)
2.5
(0E)
4
(0G)
6.3
(0J)
10
(1A)
Surge Voltage
(V)
2.8
4.6
7.2
11.5
Rated Capacitance
(μF)
Case Size
φD × L (mm)
tan δ
Leakage Current
(μA)
ESR (mΩ)
(at 100kHz 20°C)
Rated Ripple
(mArms)
Part Number
220
5×6
0.12
110
30
2100
PCG0E221MCL1GS
330
5×6
0.12
500
30
2200
PCG0E331MCL1GS
330
5×6
0.12
500
10
3300
PCG0E331MCO1GS
470
6.3 × 6
0.12
235
20
2900
PCG0E471MCL1GS
560
6.3 × 6
0.12
280
20
3000
PCG0E561MCL1GS
820
8×7
0.12
410
20
3300
PCG0E821MCL1GS
1500
10 × 8
0.12
750
17
4100
PCG0E152MCL1GS
2700
10 × 10
0.12
1350
12
4700
PCG0E272MCL1GS
3300
10 × 12.7
0.12
1650
10
5500
PCG0E332MCL1GS
4700
10 × 12.7
0.12
2350
10
5600
PCG0E472MCL1GS
PCG0G181MCL1GS
180
5×6
0.12
144
32
1900
220
5×6
0.12
300
32
2000
PCG0G221MCL1GS
220
5×6
0.12
300
15
2900
PCG0G221MCO1GS
390
6.3 × 6
0.12
312
22
2700
PCG0G391MCL1GS
680
8×7
0.12
544
21
3200
PCG0G681MCL1GS
1200
10 × 8
0.12
960
17
4000
PCG0G122MCL1GS
2200
10 × 10
0.12
1760
13
4600
PCG0G222MCL1GS
2700
10 × 12.7
0.12
2160
11
5300
PCG0G272MCL1GS
3300
10 × 12.7
0.12
2640
11
5400
PCG0G332MCL1GS
PCG0J151MCL1GS
150
5×6
0.12
189
33
1800
180
5×6
0.12
500
33
1900
PCG0J181MCL1GS
180
5×6
0.12
500
17
3000
PCG0J181MCO1GS
270
6.3 × 6
0.12
340
23
2600
PCG0J271MCL1GS
330
6.3 × 6
0.12
416
23
2700
PCG0J331MCL1GS
470
8×7
0.12
592
22
3100
PCG0J471MCL1GS
1000
10 × 8
0.12
1260
18
3800
PCG0J102MCL1GS
1800
10 × 10
0.12
2268
14
4400
PCG0J182MCL1GS
2200
10 × 12.7
0.12
2772
12
5000
PCG0J222MCL1GS
2700
10 × 12.7
0.12
3402
12
5100
PCG0J272MCL1GS
82
5×6
0.12
164
35
1700
PCG1A820MCL1GS
100
5×6
0.12
250
35
1800
PCG1A101MCL1GS
150
6.3 × 6
0.12
300
25
2500
PCG1A151MCL1GS
180
6.3 × 6
0.12
360
25
2600
PCG1A181MCL1GS
330
8×7
0.12
660
23
3100
PCG1A331MCL1GS
560
10 × 8
0.12
1120
20
3600
PCG1A561MCL1GS
10 × 10
0.12
1640
15
4300
PCG1A821MCL1GS
1000
10 × 12.7
0.12
2000
13
4800
PCG1A102MCL1GS
1500
10 × 12.7
0.12
3000
13
4900
PCG1A152MCL1GS
820
16
(1C)
18.4
47
5×6
0.12
150
40
1500
PCG1C470MCL1GS
56
5×6
0.12
240
40
1600
PCG1C560MCL1GS
82
6.3 × 6
0.12
262
30
2300
PCG1C820MCL1GS
100
6.3 × 6
0.12
320
30
2400
PCG1C101MCL1GS
150
8×7
0.12
480
28
2800
PCG1C151MCL1GS
270
10 × 8
0.12
864
25
3300
PCG1C271MCL1GS
470
10 × 10
0.12
1504
20
3700
PCG1C471MCL1GS
680
10 × 12.7
0.12
2176
18
4100
PCG1C681MCL1GS
820
10 × 12.7
0.12
2624
18
4200
PCG1C821MCL1GS
Rated ripple current (mArms) at 105°C 100kHz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please refer to page 3 for the minimum order quantity.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CS
Chip Type, Long Life Assurance
series
Load life of 5000 hours at 105°C.
SMD type : Lead free reflow soldering condition at
260°C peak correspondence.
Compliant to the RoHS directive (2011/65/EU).
CS
CF
Long Life
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C
Rated Voltage Range
4 to 16V
Rated Capacitance Range
22 to 560μF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
Less than or equal to the specified value .
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 5000 hours at 105°C.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1.25
1.25
(100kHz)
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Resistance to
Soldering Heat
Marking
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 6.3V 220μF)
1
0.5 MAX.
2
3
4
5
6
7
8
9 10 11 12 13 14
PCS 0 J 2 2 1 MC L 1 GS
Taping code
Size code
A±0.2
C±0.2
B ±0.2
qD±0.5
CS
220
j
941
Lot No.
E
Capacitance
Positive
Plastic platform
0.3 MAX.
Configuration
Capacitance tolerance (±20%)
Series
L +0.1
-0.4
Voltage ( j:6.3v)
Negative
Rated capacitance (220μF)
Rated voltage (6.3V)
H
Series name
Size
qD
L
A
B
C
E
H
Type
(mm)
q8 =7L
8.0
q5 =6L
5.0
q6.3 =6L
6.3
5.9
5.9
6.9
6.0
7.3
9.0
5.3
5.3
6.6
6.6
8.3
8.3
1.6
2.1
3.2
0.5 to 0.8 0.5 to 0.8 0.8 to 1.1
Dimension table in next page.
Voltage
V
4
6.3
10
16
Code
g
j
A
C
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CS
series
Standard Ratings
Rated Voltage
(V)(code)
4
(0G)
6.3
(0J)
10
(1A)
16
(1C)
Surge Voltage
(V)
4.6
7.2
11.5
18.4
Rated Capacitance
(μF)
Case Size
φD × L (mm)
tan δ
150
5×6
0.12
330
6.3 × 6
0.12
330
8×7
560
Leakage Current
(μA)
ESR (mΩ)
(at 100kHz 20°C)
Rated Ripple
(mArms)
Part Number
120
25
2200
PCS0G151MCL1GS
264
20
2800
PCS0G331MCL1GS
0.12
264
22
3200
PCS0G331MCL9GS
8×7
0.12
448
18
3600
PCS0G561MCL1GS
47
5×6
0.12
100
35
1600
PCS0J470MCL1GS
100
5×6
0.12
126
25
2400
PCS0J101MCL1GS
100
6.3 × 6
0.12
126
22
2800
PCS0J101MCL9GS
120
6.3 × 6
0.12
151
22
2800
PCS0J121MCL9GS
220
6.3 × 6
0.12
277
20
2800
PCS0J221MCL1GS
220
8×7
0.12
277
22
3200
PCS0J221MCL9GS
390
8×7
0.12
491
22
3200
PCS0J391MCL1GS
33
5×6
0.12
100
40
1300
PCS1A330MCL1GS
56
6.3 × 6
0.12
112
27
2300
PCS1A560MCL9GS
68
5×6
0.12
136
30
2100
PCS1A680MCL1GS
120
6.3 × 6
0.12
240
27
2300
PCS1A121MCL1GS
150
8×7
0.12
300
30
2600
PCS1A151MCL9GS
270
8×7
0.12
540
22
3200
PCS1A271MCL1GS
22
5×6
0.12
100
45
1100
PCS1C220MCL1GS
39
5×6
0.12
125
35
2000
PCS1C390MCL1GS
39
6.3 × 6
0.12
125
30
2200
PCS1C390MCL9GS
68
6.3 × 6
0.12
218
30
2200
PCS1C680MCL1GS
82
8×7
0.12
262
28
2800
PCS1C820MCL9GS
120
8×7
0.12
384
28
2800
PCS1C121MCL1GS
Rated ripple current (mArms) at 105°C 100kHz
No marked, 1 will be put at 12th digit of type numbering system.
: In this case, 9 will be put at 12th digit of type numbering system.
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please refer to page 3 for the minimum order quantity.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CV
Chip Type, High Voltage / Long Life
series
High voltage (to 125V), Low ESR, High ripple current.
Load life of 3000 hours at 105°C.
SMD type : Lead free reflow soldering condition at
260°C peak correspondence.
Compliant to the RoHS directive (2011/65/EU).
CX
CV
High Temperature
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C
Rated Voltage Range
16 to 125V
Rated Capacitance Range
5.6 to 680μF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
Less than or equal to the specified value .
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 3000 hours at 105°C.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1.25
1.25
(100kHz)
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Resistance to
Soldering Heat
Marking
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Lot No.
1
0.5 MAX.
Capacitance
Type numbering system (Example : 35V 82μF)
Positive
Plastic platform
0.3 MAX.
C±0.2
2
3
4
5
6
7
8
9 10 11 12 13 14
PCV 1 V 8 2 0 MC L 1 GS
Taping code
A±0.2
E
B±0.2
qD±0.5
CV
82
V
012
Size code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (82μF)
L +0.1
-0.4
Voltage (V:35V)
Series
Rated voltage (35V)
Negative
Series name
H
Type
(mm)
Size q6.3 ×6L q8 ×7L q8 ×10L q8 ×12L q10 ×8L q10 ×10L q10×12.7L
qD
6.3
8.0
8.0
8.0
10.0
10.0
10.0
L
5.9
6.9
9.9
11.9
7.9
9.9
12.6
A
7.3
9.0
9.0
9.0
11.0
11.0
11.0
B
6.6
8.3
8.3
8.3
10.3
10.3
10.3
C
6.6
8.3
8.3
8.3
10.3
10.3
10.3
E
2.1
3.2
3.2
3.2
4.6
4.6
4.6
H
0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
Dimension table in next page.
Voltage
V
16
20
25
35
50
63
80
100
125
Code
C
D
E
V
H
J
K
2A
2B
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CV
series
Standard Ratings
Rated Voltage
(V)(code)
Surge Voltage
(V)
Rated Capacitance
(μF)
Case Size
φD × L (mm)
tan δ
Leakage Current
(μA)
56
6.3 × 6
0.12
179
82
6.3 × 6
0.12
262
100
8×7
0.12
150
8×7
220
8 × 10
220
16
(1C)
20
(1D)
18.4
23.0
28.7
40.2
Part Number
50
1000
PCV1C560MCL1GS
47
1300
PCV1C820MCL2GS
320
36
1500
PCV1C101MCL1GS
0.12
480
34
1700
PCV1C151MCL2GS
0.12
704
27
2000
PCV1C221MCL6GS
0.12
704
31
2000
PCV1C221MCL1GS
8 × 10
0.12
864
21
3800
PCV1C271MCL7GS
270
8 × 12
0.12
864
26
2300
PCV1C271MCL1GS
270
10 × 8
0.12
864
24
3200
PCV1C271MCL2GS
330
10 × 10
0.12
1056
26
2400
PCV1C331MCL1GS
390
8 × 12
0.12
1248
20
4100
PCV1C391MCL2GS
470
10 × 10
0.12
1504
21
3900
PCV1C471MCL2GS
470
10 × 12.7
0.12
1504
25
2800
PCV1C471MCL1GS
680
10 × 12.7
0.12
2176
19
4400
PCV1C681MCL2GS
47
6.3 × 6
0.12
188
55
1000
PCV1D470MCL1GS
56
6.3 × 6
0.12
224
48
1300
PCV1D560MCL2GS
68
8×7
0.12
272
45
1300
PCV1D680MCL1GS
100
8×7
0.12
400
42
1400
PCV1D101MCL2GS
150
8 × 10
0.12
600
28
2000
PCV1D151MCL6GS
150
10 × 8
0.12
600
33
1900
PCV1D151MCL1GS
180
10 × 8
0.12
720
25
3100
PCV1D181MCL2GS
220
8 × 10
0.12
880
22
3700
PCV1D221MCL7GS
220
8 × 12
0.12
880
27
2300
PCV1D221MCL1GS
270
8 × 12
0.12
1080
21
4000
PCV1D271MCL2GS
270
10 × 10
0.12
1080
27
2300
PCV1D271MCL1GS
330
10 × 10
0.12
1320
22
3800
PCV1D331MCL2GS
330
10 × 12.7
0.12
1320
26
2700
PCV1D331MCL1GS
470
10 × 12.7
0.12
1880
20
4300
PCV1D471MCL2GS
33
6.3 × 6
0.12
165
60
1000
PCV1E330MCL1GS
47
6.3 × 6
0.12
235
49
1300
PCV1E470MCL2GS
56
8×7
0.12
280
50
1300
PCV1E560MCL1GS
82
8×7
0.12
410
47
1400
PCV1E820MCL2GS
120
8 × 10
0.12
600
29
1900
PCV1E121MCL6GS
0.12
600
35
1800
PCV1E121MCL1GS
10 × 8
150
8 × 10
0.12
750
23
3600
PCV1E151MCL7GS
150
8 × 12
0.12
750
28
2200
PCV1E151MCL1GS
150
10 × 8
0.12
750
26
3000
PCV1E151MCL2GS
180
10 × 10
0.12
900
28
2300
PCV1E181MCL1GS
220
8 × 12
0.12
1100
22
3800
PCV1E221MCL2GS
270
10 × 10
0.12
1350
23
3700
PCV1E271MCL2GS
270
10 × 12.7
0.12
1350
27
2700
PCV1E271MCL1GS
390
10 × 12.7
0.12
1950
21
4200
PCV1E391MCL2GS
18
6.3 × 6
0.12
126
64
900
PCV1V180MCL1GS
22
6.3 × 6
0.12
154
50
1300
PCV1V220MCL2GS
27
8× 7
0.12
189
55
1200
PCV1V270MCL1GS
39
8× 7
0.12
273
52
1400
PCV1V390MCL2GS
56
8 × 10
0.12
392
31
1900
PCV1V560MCL1GS
0.12
476
37
1800
PCV1V680MCL1GS
68
35
(1V)
Rated Ripple
(mArms)
270
120
25
(1E)
10 × 8
ESR (mΩ)
(at 100kHz 20°C)
10 × 8
82
8 × 10
0.12
574
24
3600
PCV1V820MCL7GS
82
8 × 12
0.12
574
29
2200
PCV1V820MCL1GS
82
10 × 8
0.12
574
27
3000
PCV1V820MCL2GS
100
10 × 10
0.12
700
29
2200
PCV1V101MCL1GS
120
8 × 12
0.12
840
23
3800
PCV1V121MCL7GS
120
10 × 10
0.12
840
24
3700
PCV1V121MCL2GS
150
10 × 12.7
0.12
1050
28
2600
PCV1V151MCL1GS
180
10 × 12.7
0.12
1260
22
4100
PCV1V181MCL2GS
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CV
series
Standard Ratings
Rated Voltage
(V)(code)
Surge Voltage
(V)
Rated Capacitance
(μF)
80
(1K)
72.4
92.0
125
(2B)
115
143
Rated Ripple
(mArms)
Part Number
0.12
82
81
800
PCV1H8R2MCL1GS
0.12
120
55
1200
PCV1H120MCL2GS
15
8×7
0.12
150
63
1100
PCV1H150MCL1GS
22
8×7
0.12
220
60
1300
PCV1H220MCL2GS
33
8 × 10
0.12
330
36
1700
PCV1H330MCL6GS
0.12
330
49
1500
PCV1H330MCL1GS
10 × 8
39
8 × 12
0.12
390
34
2000
PCV1H390MCL1GS
47
8 × 10
0.12
470
29
3300
PCV1H470MCL7GS
47
10 × 8
0.12
470
37
2600
PCV1H470MCL2GS
47
10 × 10
0.12
470
30
2200
PCV1H470MCL1GS
56
8 × 12
0.12
560
28
3400
PCV1H560MCL2GS
68
10 × 10
0.12
680
29
3400
PCV1H680MCL2GS
68
10 × 12.7
0.12
680
29
2600
PCV1H680MCL1GS
100
10 × 12.7
0.12
1000
27
3600
PCV1H101MCL2GS
5.6
6.3 × 6
0.12
71
105
700
PCV1J5R6MCL1GS
8.2
6.3 × 6
0.12
103
56
1200
PCV1J8R2MCL2GS
10
8×7
0.12
126
75
1000
PCV1J100MCL1GS
12
8×7
0.12
151
70
1100
PCV1J120MCL2GS
22
8 × 10
0.12
277
37
1700
PCV1J220MCL6GS
0.12
277
56
1400
PCV1J220MCL1GS
10 × 8
27
8 × 10
0.12
340
30
3200
PCV1J270MCL7GS
27
8 × 12
0.12
340
35
2000
PCV1J270MCL1GS
27
10 × 8
0.12
340
38
2500
PCV1J270MCL2GS
33
10 × 10
0.12
416
31
2200
PCV1J330MCL1GS
39
8 × 12
0.12
491
29
3400
PCV1J390MCL2GS
47
10 × 10
0.12
592
30
3300
PCV1J470MCL2GS
47
10 × 12.7
0.12
592
30
2500
PCV1J470MCL1GS
56
10 × 12.7
0.12
706
28
3400
PCV1J560MCL2GS
10
8 × 10
0.12
160
43
1600
PCV1K100MCL1GS
12
8 × 12
0.12
192
41
1800
PCV1K120MCL1GS
15
10 × 10
0.12
240
39
1900
PCV1K150MCL1GS
22
10 × 12.7
0.12
352
38
2200
PCV1K220MCL1GS
8 × 10
0.12
136
48
1500
PCV2A6R8MCL1GS
10
8 × 12
0.12
200
45
1700
PCV2A100MCL1GS
12
10 × 10
0.12
240
42
1900
PCV2A120MCL1GS
18
10 × 12.7
0.12
360
41
2100
PCV2A180MCL1GS
6.8
8 × 10
0.12
170
93
1100
PCV2B6R8MCL1GS
8.2
8 × 12
0.12
205
84
1300
PCV2B8R2MCL1GS
12
10 × 10
0.12
300
69
1400
PCV2B120MCL1GS
15
10 × 12.7
0.12
375
48
2000
PCV2B150MCL1GS
6.8
100
(2A)
ESR (mΩ)
(at 100kHz 20°C)
6.3 ×6
22
63
(1J)
Leakage Current
(μA)
6.3 × 6
33
57.5
tan δ
12
8.2
50
(1H)
Case Size
φD × L (mm)
No marked, 1
: In this case,
: In this case,
: In this case,
Rated ripple current (mArms) at 105°C 100kHz
will be put at 12th digit of type numbering system.
2 will be put at 12th digit of type numbering system.
6 will be put at 12th digit of type numbering system.
7 will be put at 12th digit of type numbering system.
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please refer to page 3 for the minimum order quantity.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CX
Chip Type, High Voltage / Long Life
series
High reliability, High voltage (to 50V).
Low ESR, High ripple current.
Long life of 1500 to 3000 hours at 125°C.
SMD type : Lead free reflow soldering condition at
260°C peak complete correspondence.
Adapted to the RoHS directive (2011/65/EU).
CR
Higher
Capacitance
CX
Higher
Temperature
CV
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +125°C
Rated Voltage Range
16 to 50V
Rated Capacitance Range
5.6 to 390μF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
Less than or equal to the specified value .
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+125°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at below shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 3000 hours (qD = 6.3:1500hours) at 125°C.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of initial capacitance value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at below shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of initial capacitance value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1.25
1.25
(100kHz)
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Resistance to
Soldering Heat
Marking
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Type numbering system (Example : 35V 39μF)
Dimensions
1
Positive
2
3
4
5
6
7
8
9 10 11 12 13 14
PCX 1 V 3 9 0 MC L 1 GS
0.5 MAX.
Plastic platform
0.3 MAX.
C±0.2
Taping code
Size code
Configuration
B ±0.2
A±0.2
Capacitance tolerance (±20%)
qD±0.5
Lot No.
CX
39
V
012
Capacitance
E
Standard
Configuration
Standard
Vibration Resistance
Rated capacitance (39μF)
Rated voltage (35V)
code
L
S
Series name
Voltage (V:35V)
Series
L +0.1
-0.4
Type
Negative
H
Positive
Series
Voltage (V:35V)
E
L±0.5
(mm)
Negative
(mm)
Size q6.3 ×8L q8 ×7.5L q8×10.5L q10×10.5L
qD 6.3 8.0 8.0 10.0
L
5.9
7.9
6.9
9.9
11.9
7.9
12.6
L
7.5
7.0 10.0 10.0
A
7.3
7.3
9.0
9.0
9.0
11.0 11.0 11.0
A
7.3
9.0
9.0
11.0
B
6.6
6.6
8.3
8.3
8.3
10.3 10.3 10.3
B
6.6
8.3
8.3
10.3
C
6.6
6.6
8.3
8.3
8.3
10.3 10.3 10.3
C
6.6
8.3
8.3
10.3
E
2.1
2.1
3.2
3.2
3.2
4.6
E
2.5
2.5
3.1
4.6
H
9.9
Vibration Resistance
4.6
4.6
0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
H
0.5 to 0.8 0.8 to 1.1 1.1 to 1.5 1.1 to 1.5
H
Aid electrode
Dimension table in next page.
Standard
Size q6.3 ×6L q6.3 ×8L q8 ×7L q8 ×10L q8 ×12L q10 ×8L q10 ×10L q10×12.7L
qD 6.3 6.3 8.0 8.0 8.0 10.0 10.0 10.0
A±0.2
C±0.2
B±0.2
qD±0.5
Lot No.
CX
39
V
012
Capacitance
Plastic platform
0.3 MAX.
0.5 MAX.
Vibration Resistance
Voltage
V
16
20
25
35
50
Code
C
D
E
V
H
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CX
series
Standard Ratings
Rated Voltage
(V)(code)
Surge Voltage
(V)
16
(1C)
18.4
20
(1D)
23.0
25
(1E)
28.7
35
(1V)
40.2
50
(1H)
57.5
Rated Capacitance
(μF)
47
82
82
100
100
150
150
150
220
270
270
390
33
56
56
68
68
120
120
120
150
180
180
270
22
39
39
56
56
82
82
82
120
120
120
180
10
18
18
27
27
39
39
39
56
68
68
100
100
5.6
10
10
12
12
22
22
22
27
33
33
47
Case Size
φD × L (mm)
tan δ
Leakage Current
(μA)
6.3 × 6
8×7
8 × 7.5
6.3 × 8
6.3 × 8
8 × 10
8 × 10.5
10 × 8
8 × 12
10 × 10
10 × 10.5
10 × 12.7
6.3 × 6
8×7
8 × 7.5
6.3 × 8
6.3 × 8
8 × 10
8 × 10.5
10 × 8
8 × 12
10 × 10
10 × 10.5
10 × 12.7
6.3 × 6
8×7
8 × 7.5
6.3 × 8
6.3 × 8
8 × 10
8 × 10.5
10 × 8
8 × 12
10 × 10
10 × 10.5
10 × 12.7
6.3 × 6
8×7
8 × 7.5
6.3 × 8
6.3 × 8
8 × 10
8 × 10.5
10 × 8
8 × 12
10 × 10
10 × 10.5
10 × 10.5
10 × 12.7
6.3 × 6
8 × 7
8 × 7.5
6.3 × 8
6.3 × 8
8 × 10
8 × 10.5
10 × 8
8 × 12
10 × 10
10 × 10.5
10 × 12.7
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
150
262
262
320
320
480
480
480
704
864
864
1248
132
224
224
272
272
480
480
480
600
720
720
1080
110
195
195
280
280
410
410
410
600
600
600
900
70
126
126
189
189
273
273
273
392
476
476
700
700
56
100
100
120
120
220
220
220
270
330
330
470
Ambient temperature of a capacitor
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please refer to page 3 for the minimum order quantity.
Rated Ripple(mArms)
ESR (mΩ)
(at 100kHz 20°C)
55
45
45
33
33
28
28
33
27
27
27
26
60
50
50
34
34
29
29
35
28
28
28
27
65
55
55
35
35
30
30
36
29
29
29
28
85
60
60
45
45
35
35
41
33
30
30
25
29
105
75
75
65
65
37
37
56
35
31
31
30
1000
1300
1300
1500
1500
2000
2000
1900
2300
2300
2300
2700
900
1300
1300
1450
1450
1900
1900
1800
2200
2300
2300
2700
900
1200
1200
1400
1400
1900
1900
1800
2200
2200
2200
2600
800
1100
1100
1300
1300
1800
1800
1700
2000
2200
2200
2400
2600
700
1000
1000
1100
1100
1700
1700
1400
2000
2200
2200
2500
390
530
530
460
460
780
780
830
870
830
830
1040
380
500
500
470
470
770
770
810
860
800
800
1020
360
480
480
450
450
760
760
800
850
790
790
1010
310
450
450
450
450
700
700
750
780
740
740
800
990
280
410
410
380
380
680
680
730
760
630
630
970
Part Number
PCX1C470MCL1GS
PCX1C820MCL1GS
PCX1C820MCS1GS
PCX1C101MCL1GS
PCX1C101MCS1GS
PCX1C151MCL6GS
PCX1C151MCS1GS
PCX1C151MCL1GS
PCX1C221MCL1GS
PCX1C271MCL1GS
PCX1C271MCS1GS
PCX1C391MCL1GS
PCX1D330MCL1GS
PCX1D560MCL1GS
PCX1D560MCS1GS
PCX1D680MCL1GS
PCX1D680MCS1GS
PCX1D121MCL6GS
PCX1D121MCS1GS
PCX1D121MCL1GS
PCX1D151MCL1GS
PCX1D181MCL1GS
PCX1D181MCS1GS
PCX1D271MCL1GS
PCX1E220MCL1GS
PCX1E390MCL1GS
PCX1E390MCS1GS
PCX1E560MCL1GS
PCX1E560MCS1GS
PCX1E820MCL6GS
PCX1E820MCS1GS
PCX1E820MCL1GS
PCX1E121MCL6GS
PCX1E121MCL1GS
PCX1E121MCS1GS
PCX1E181MCL1GS
PCX1V100MCL1GS
PCX1V180MCL1GS
PCX1V180MCS1GS
PCX1V270MCL1GS
PCX1V270MCS1GS
PCX1V390MCL6GS
PCX1V390MCS1GS
PCX1V390MCL1GS
PCX1V560MCL1GS
PCX1V680MCL1GS
PCX1V680MCS1GS
PCX1V101MCS1GS
PCX1V101MCL1GS
PCX1H5R6MCL1GS
PCX1H100MCL1GS
PCX1H100MCS1GS
PCX1H120MCL1GS
PCX1H120MCS1GS
PCX1H220MCL6GS
PCX1H220MCS1GS
PCX1H220MCL1GS
PCX1H270MCL1GS
PCX1H330MCL1GS
PCX1H330MCS1GS
PCX1H470MCL1GS
Rated ripple current (mArms) at 105°C 100kHz
No marked, 1 will be put at 12th digit of type numbering system.
: In this case, 6 will be put at 12th digit of type numbering system.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CR
Chip Type, High Reliability
series
High reliability, High voltage (to 80V).
Low ESR, High ripple current.
Long life of 4000 hours at 125°C.
SMD type : Lead free reflow soldering condition at
260°C peak complete correspondence.
Adapted to the RoHS directive (2011/65/EU).
ESR after Endurance at -40°C.
CR
High Capacitance
Long Life Assurance
CX
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +125°C
Rated Voltage Range
16 to 80V
Rated Capacitance Range
22 to 1000μF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV or 3(μA), whichever is greater.
Temperature Characteristics
(Max.Impedance Ratio)
Z+125°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 4000 hours at 125°C.
Shelf Life
The specifications listed above shall be met when the capacitors are restored to 20°C after the rated voltage is applied for
1000 hours at 85°C, 85% RH.
ESR after Endurance (
1)
1.25
1.25
(100kHz)
Within ± 20% of initial capacitance value ( 3)
150% or less of the initial specified value
200% or less of the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Less than or equal to the specified value at 100kHz, -40°C
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 85°C, 85% RH.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of initial capacitance value ( 3)
150% or less of the initial specified value
200% or less of the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In case peak temperature is 260°C or less, reflow soldering shall be
two times maximum.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
C±0.2
2
3
4
5
6
7
8
9 10 11 12 13 14
PCR 1 V 1 5 1 MC L 1 GS
Taping code
Size code
A±0.2
E
B ±0.2
qD±0.5
Configuration
Capacitance tolerance (±20%)
Rated capacitance (150μF)
Rated voltage (35V)
L +0.1
-0.4
Voltage (V:35V)
Series
1
0.5 MAX.
Plastic platform
0.3 MAX.
Lot No.
CR
150
V
331
Capacitance
Type numbering system (Example : 35V 150μF)
Positive
Dimensions
Negative
Series name
H
Type
(mm)
Size
qD
q8 × 7L q8 × 10L q8 × 12L q10 × 8L q10 ×10L q10×12.7L
8.0
8.0
8.0
10.0
10.0
10.0
L
6.9
9.9
11.9
7.9
9.9
12.6
A
9.0
9.0
9.0
11.0
11.0
11.0
B
8.3
8.3
8.3
10.3
10.3
10.3
C
8.3
8.3
8.3
10.3
10.3
10.3
3.2
3.2
3.2
4.6
4.6
4.6
E
H
0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
Dimension table in next page.
φ8 × 7L, φ8 × 10L, φ10 × 10L :
The vibration structure-resistant product is also available upon request, please ask for details.
Voltage
V
16
20
25
35
50
63
80
Code
C
D
E
V
H
J
K
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CR
series
Standard Ratings
Rated Voltage
(V)(code)
16
(1C)
Surge Voltage
(V)
25
(1E)
35
(1V)
50
(1H)
63
(1J)
80
(1K)
31
63
79
100
45
1500
PCR1C221MCL1GS
17
26
3400
PCR1C471MCL6GS
8 × 10
10 × 8
Rated Ripple
(mArms)
Part Number
(125°C / 100kHz)
0.08
32
48
2200
PCR1C471MCL1GS
560
8 × 12
0.08
16
24
3800
PCR1C561MCL1GS
680
10 × 10
0.08
19
29
3200
PCR1C681MCL1GS
10 × 12.7
0.08
13
20
4300
PCR1C102MCL1GS
150
8×7
0.08
39
59
1200
PCR1D151MCL1GS
330
8 × 10
0.08
19
29
3300
PCR1D331MCL6GS
0.08
33
50
2100
PCR1D331MCL1GS
10 × 8
470
8 × 12
0.08
18
27
3500
PCR1D471MCL1GS
560
10 × 10
0.08
20
30
3100
PCR1D561MCL1GS
680
10 × 12.7
0.08
14
21
4200
PCR1D681MCL1GS
100
8×7
0.08
41
62
1200
PCR1E101MCL1GS
220
8 × 10
0.08
20
30
3200
PCR1E221MCL6GS
0.08
33
50
2100
PCR1E221MCL1GS
220
10 × 8
270
8 × 12
0.08
19
29
3300
PCR1E271MCL1GS
330
10 × 10
0.08
20
30
3100
PCR1E331MCL1GS
470
10 × 12.7
0.08
15
23
4100
PCR1E471MCL1GS
68
8×7
0.08
44
66
1200
PCR1V680MCL1GS
150
8 × 10
0.08
22
33
3100
PCR1V151MCL6GS
0.08
33
50
2100
PCR1V151MCL1GS
150
43
30
0.08
8×7
470
330
25
0.08
220
1000
20
(1D)
Low temp.
ESR after
Endurance
(mΩ)
(-40°C / 100kHz)
tan δ
470
20
Initial
ESR
(mΩ)
(20°C / 100kHz)
Case Size
φD × L (mm)
Rated Capacitance
(μF)
10 × 8
220
8 × 12
0.08
21
32
3300
PCR1V221MCL1GS
270
10 × 10
0.08
20
30
3100
PCR1V271MCL1GS
330
10 × 12.7
0.08
16
24
3900
PCR1V331MCL1GS
39
8×7
0.08
45
68
1300
PCR1H390MCL1GS
82
8 × 10
0.08
26
39
2900
PCR1H820MCL6GS
0.08
42
63
1900
PCR1H820MCL1GS
82
10 × 8
120
8 × 12
0.08
25
38
2900
PCR1H121MCL2GS
120
10 × 10
0.08
25
38
3000
PCR1H121MCL1GS
180
10 × 12.7
0.08
19
29
3500
PCR1H181MCL1GS
22
8×7
0.08
48
72
1100
PCR1J220MCL1GS
39
8 × 10
0.08
28
42
2700
PCR1J390MCL1GS
0.08
47
70
1800
PCR1J470MCL1GS
47
10 × 8
56
8 × 12
0.08
27
41
2900
PCR1J560MCL1GS
68
10 × 10
0.08
28
42
2800
PCR1J680MCL1GS
100
10 × 12.7
0.08
24
36
3000
PCR1J101MCL1GS
27
8 × 10
0.08
38
57
1400
PCR1K270MCL1GS
39
8 × 12
0.08
35
53
1600
PCR1K390MCL1GS
47
10 × 10
0.08
33
50
1700
PCR1K470MCL1GS
68
10 × 12.7
0.08
28
42
2100
PCR1K680MCL1GS
Rated ripple current (mArms) at 125°C 100kHz
No marked, 1 will be put at 12th digit of type numbering system.
: In this case, 2 will be put at 12th digit of type numbering system.
: In this case, 6 will be put at 12th digit of type numbering system.
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please refer to page 3 for the minimum order quantity.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LF
Radial Lead Type, Standard
series
Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type :
Lead free flow soldering condition correspondence.
Compliant to the RoHS directive (2011/65/EU).
LS
LG
Higher
Capacitance
Long Life
LF
Low ESR
LE
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C
Rated Voltage Range
2.5 to 25V
Rated Capacitance Range
6.8 to 1500μF
Capacitance Tolerance
± 20%
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
at 120Hz, 20°C
Less than or equal to the specified value.
1.25
1.25
After 2 minutes' application of rated voltage at 20°C
(100kHz)
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
ESR (
1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Damp Heat
(Steady State)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
ESR (
1)
Leakage current ( 2)
Resistance to
Soldering Heat
After soldering the capacitor under the soldering conditions
prescribed here as preheat at 150 to 200°C for 60 to 180 seconds
and peak temperature at 265°C for 10 seconds or less, the
capacitor shall meet the specifications listed at right, provided that
its temperature profile is measured at both of terminal ends facing
the soldering side.
Marking
Navy blue print on the case top
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
ESR (
1)
Leakage current ( 2)
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 4V 560μF)
Resin coated Case
Capacitance
1
2
3
4
5
6
7
8
9 10 11 12
P L F 0 G 5 6 1 MDO 1
P ±0.5
qD±0.5
LF
560
g
841
Voltage(g:4V)
Size code
Configuration
Capacitance tolerance (±20%)
qd
Series
Lot. No.
L+0.5MAX.
15MIN
Rated capacitance (560μF)
4MIN
Rated voltage (4V)
Series name
Type
Size
qD
L
P
qd
q6.3 =6L q6.3 =9L q6.3 =10.5L q8 =7L
6.3
6.3
8.0
6.3
5.5
8.5
6.5
10.0
2.5
2.5
3.5
2.5
0.45
0.6
0.6
0.5
q8 =9L
8.0
8.5
3.5
0.6
(mm)
q8 =12L q10 =8L q10 =10L q10 =13L
8.0
10.0
10.0
10.0
11.5
7.5
9.5
12.5
3.5
5.0
5.0
5.0
0.6
0.6
0.6
0.6
Voltage
V
Code
2.5
4
6.3
10
16
20
25
e
g
j
A
C
D
E
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LF
Standard Ratings
series
Rated Voltage
(V)(code)
2.5
(0E)
4
(0G)
6.3
(0J)
10
(1A)
16
(1C)
20
(1D)
25
(1E)
Surge Voltage
(V)
2.8
4.6
7.2
11.5
18.4
23
28.7
Rated Capacitance
(μF)
Case Size
φD × L (mm)
tan δ
Leakage Current
ESR (mΩ)
(μA)
(at 100kHz 20°C)
Rated Ripple
(mArms)
Part Number
330
6.3 × 9
0.08
500
390
6.3 × 10.5
0.08
195
7
5600
PLF0E331MCO8
20
3200
560
6.3 × 9
0.08
500
PLF0E391MDL4
7
5600
PLF0E561MCO8
560
8×9
0.08
680
8×9
0.08
280
6
4800
PLF0E561MCO1
340
7
4800
680
8 × 12
PLF0E681MCO6
0.08
340
6
5700
PLF0E681MDO1
820
6.3 × 9
0.08
500
7
5600
PLF0E821MCO8
820
8×9
0.08
410
7
5200
PLF0E821MCO6
820
8 × 12
0.08
410
6
6200
PLF0E821MDO1
1000
10 × 13
0.08
500
6
6500
PLF0E102MDO1
1200
10 × 13
0.08
600
8
5300
PLF0E122MDO1
1500
8 × 12
0.08
750
7
6100
PLF0E152MDO6
1500
10 × 13
0.08
750
8
5500
PLF0E152MDO1
270
6.3 × 9
0.08
500
7
5600
PLF0G271MCO8
270
6.3 × 10.5
0.08
216
20
3200
PLF0G271MDL4
390
6.3 × 10.5
0.08
312
24
3300
PLF0G391MDL4
560
8×9
0.08
448
7
5200
PLF0G561MCO6
560
8 × 12
0.08
448
7
5500
PLF0G561MDO1
680
8 × 12
0.08
544
6
6200
PLF0G681MDO1
820
10 × 13
0.08
656
6
6500
PLF0G821MDO1
1000
10 × 13
0.08
800
6
6640
PLF0G102MDO1
1200
10 × 13
0.08
960
8
5600
PLF0G122MDO1
220
6.3 × 10.5
0.08
277
20
3200
PLF0J221MDL4
330
6.3 × 10.5
0.08
416
24
3300
PLF0J331MDL4
470
8×9
0.08
592
7
5200
PLF0J471MCO6
470
8 × 12
0.08
592
7
5500
PLF0J471MDO1
680
10 × 13
0.08
857
6
6300
PLF0J681MDO1
47
6.3 × 10.5
0.08
94
25
2900
PLF1A470MDL4
68
6.3 × 10.5
0.08
136
25
2900
PLF1A680MDL4
100
6.3 × 10.5
0.08
200
25
2900
PLF1A101MDL4
150
6.3 × 10.5
0.08
300
25
2900
PLF1A151MDL4
270
8 × 12
0.08
540
8
4900
PLF1A271MDO1
470
10 × 13
0.08
940
7
5700
PLF1A471MDO1
560
10 × 13
0.08
1120
7
5900
PLF1A561MDO1
680
10 × 13
0.08
1360
7
6100
PLF1A681MDO1
100
6.3 × 10.5
0.08
320
24
2900
PLF1C101MDL4
180
8 × 12
0.08
576
9
5000
PLF1C181MDO1
270
8 × 12
0.08
864
9
5100
PLF1C271MDO1
330
10 × 13
0.08
1056
9
6100
PLF1C331MDO1
470
10 × 13
0.08
1504
9
6100
PLF1C471MDO1
22
6.3 × 6
0.12
88
50
1700
PLF1D220MCL2
39
8×7
0.12
156
45
2000
PLF1D390MCL2
47
8×7
0.12
188
45
2000
PLF1D470MCL2
56
10 × 8
0.12
224
40
2400
PLF1D560MCL2
68
10 × 8
0.12
272
40
2600
PLF1D680MCL2
82
10 × 8
0.12
328
40
2600
PLF1D820MCL2
PLF1D101MDO2
100
8 × 12
0.12
400
22
3320
120
10 × 10
0.12
480
35
2800
PLF1D121MCL2
150
10 × 13
0.12
600
20
4320
PLF1D151MDO2
6.8
6.3 × 6
0.12
85
80
1200
PLF1E6R8MCL2
10
6.3 × 6
0.12
125
65
1500
PLF1E100MCL7
10
8×7
0.12
125
60
1500
PLF1E100MCL2
22
8×7
0.12
275
50
1800
PLF1E220MCL7
47
10 × 13
0.12
588
30
3000
PLF1E470MDO2
56
10 × 13
0.12
700
28
3800
PLF1E560MDO2
Please refer to page 20, 21, 22 about the formed or taped product spec.
Please refer to page 3 for the minimum order quantity.
No marked, 1
: In this case,
: In this case,
: In this case,
: In this case,
: In this case,
will be put
2 will be
4 will be
6 will be
7 will be
8 will be
Rated ripple current (mArms) at 105°C 100kHz
at 12th digit of type numbering system.
put at 12th digit of type numbering system.
put at 12th digit of type numbering system.
put at 12th digit of type numbering system.
put at 12th digit of type numbering system.
put at 12th digit of type numbering system.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Radial Lead Type, Ultra-low ESR
LE
series
Ultra-low ESR, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type :
Lead free flow soldering condition correspondence
Compliant to the RoHS directive (2011/65/EU).
LF
LE
Low ESR
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C
Rated Voltage Range
2.5 to 6.3V
Rated Capacitance Range
470 to 1500μF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
Less than or equal to the specified value.
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
After soldering the capacitor under the soldering conditions prescribed
here as preheat at 150 to 200°C for 60 to 180 seconds and peak
temperature at 265°C for 10 seconds or less, the capacitor shall meet
the specifications listed at right, provided that its temperature profile is
measured at both of terminal ends facing the soldering side.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
Marking
Navy blue print on the case top
1.25
1.25
(100kHz)
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 4V 560μF)
1
Resin coated Case
Capacitance
P ±0.5
qD±0.5
LE
560
g
841
3
4
5
6
7
8
9 10 11 12
Size code
Configuration
Capacitance tolerance (±20%)
qd
Series
2
P L E 0 G 5 6 1 MCO 1
Voltage(g:4V)
Rated capacitance (560μF)
Lot. No.
L+0.5MAX.
15MIN
4MIN
Rated voltage (4V)
Series name
Size
qD
L
P
qd
(mm)
q10 =13L
10.0
Type
q8 =9L
8.0
q8 =12L
8.0
8.5
3.5
11.5
3.5
12.5
5.0
V
2.5
4
6.3
0.6
0.6
0.6
Code
e
g
j
Voltage
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LE
series
Standard Ratings
Rated Voltage
Surge Voltage
(V)
(V)
Code
2.5
(0E)
4
(0G)
6.3
(0J)
2.8
4.6
7.2
Rated Capacitance
(μF)
Case Size
φD × L (mm)
tan δ
Leakage Current
(μA)
ESR (mΩ)
(at 100kHz 20°C)
Rated Ripple
(mArms)
560
8×9
0.08
280
5
6100
PLE0E561MCO1
820
8×9
0.08
410
5
6300
PLE0E821MCO6
Part Number
820
8 × 12
0.08
410
5
6600
PLE0E821MDO1
1000
10 × 13
0.08
500
5
7100
PLE0E102MDO1
1500
10 × 13
0.08
750
5
7300
PLE0E152MDO1
560
8×9
0.08
448
5
6000
PLE0G561MCO1
680
8 × 12
0.08
544
5
6500
PLE0G681MDO1
820
10 × 13
0.08
656
5
7000
PLE0G821MDO1
1200
10 × 13
0.08
960
5
7200
PLE0G122MDO1
470
8 × 12
0.08
592
5
6400
PLE0J471MDO1
680
10 × 13
0.08
857
5
6700
PLE0J681MDO1
820
10 × 13
0.08
1033
5
6800
PLE0J821MDO1
Rated ripple current (mArms) at 105°C 100kHz
No marked, 1 will be put at 12th digit of type numbering system.
: In this case, 6 will be put at 12th digit of type numbering system.
Please refer to page 20, 21, 22 about the formed or taped product spec.
Please refer to page 3 for the minimum order quantity.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LG
Radial Lead Type, Higher Capacitance
series
Higher Capacitance, Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type :
Lead free flow soldering condition correspondence
Compliant to the RoHS directive (2011/65/EU).
LG
Higher
Capacitance
LF
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C
Rated Voltage Range
2.5 to 16V
Rated Capacitance Range
330 to 3900μF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
Less than or equal to the specified value.
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
After soldering the capacitor under the soldering conditions prescribed
here as preheat at 150 to 200°C for 60 to 180 seconds and peak
temperature at 265°C for 10 seconds or less, the capacitor shall meet
the specifications listed at right, provided that its temperature profile is
measured at both of terminal ends facing the soldering side.
Capacitance change
tan b
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
Marking
Navy blue print on the case top
1.25
1.25
(100kHz)
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 4V 1200μF)
Resin coated Case
Capacitance
1
2
3
4
5
6
7
8
9 10 11 12
P L G 0 G 1 2 2 MCO 1
P ±0.5
qD±0.5
LG
1200
g
841
Voltage(g:4V)
Size code
Configuration
Capacitance tolerance (±20%)
qd
Series
Lot. No.
L+0.5MAX.
15MIN
Rated capacitance (1200μF)
4MIN
Rated voltage (4V)
Size
qD
L
P
qd
q8 =9L
8.0
8.5
3.5
0.6
(mm)
q8 =12L q10 =13L
8.0
10.0
11.5
3.5
0.6
Series name
Type
Voltage
12.5
5.0
V
2.5
4
6.3
10
16
0.6
Code
e
g
j
A
C
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LG
series
Standard Ratings
Rated Voltage
(V)
Code
2.5
(0E)
4
(0G)
6.3
(0J)
10
(1A)
16
(1C)
Surge Voltage
(V)
2.8
4.6
7.2
11.5
18.4
Rated Capacitance
(μF)
Case Size
φD × L (mm)
tan δ
Leakage Current
(μA)
ESR (mΩ)
(at 100kHz 20°C)
Rated Ripple
(mArms)
Part Number
1800
8×9
2200
8 × 12
0.08
900
9
6000
PLG0E182MCO1
0.08
1100
8
6700
PLG0E222MDO1
2700
10 × 13
0.08
1350
8
5560
PLG0E272MDO1
3900
10 × 13
0.08
1950
8
7000
PLG0E392MDO1
1200
8×9
0.08
960
9
5900
PLG0G122MCO1
1800
8 × 12
0.08
1440
9
6500
PLG0G182MDO1
2700
10 × 13
0.08
2160
8
6900
PLG0G272MDO1
820
8×9
0.08
1033
9
5700
PLG0J821MCO1
1200
8 × 12
0.08
1512
9
6100
PLG0J122MDO1
1500
10 × 13
0.08
1890
9
6300
PLG0J152MDO1
1800
10 × 13
0.08
2268
8
6600
PLG0J182MDO1
560
8×9
0.08
1120
11
5100
PLG1A561MCO1
PLG1A821MDO1
820
8 × 12
0.08
1640
10
5800
1200
10 × 13
0.08
2400
9
6200
PLG1A122MDO1
330
8×9
0.08
1056
13
4700
PLG1C331MCO1
470
8 × 12
0.08
1504
11
5400
PLG1C471MDO1
820
10 × 13
0.08
2624
11
5600
PLG1C821MDO1
Rated ripple current (mArms) at 105°C 100kHz
Please refer to page 20, 21, 22 about the formed or taped product spec.
Please refer to page 3 for the minimum order quantity.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LS
Radial Lead Type, Long Life Assurance
series
Ultra-low ESR, High ripple current.
Load life of 5000 hours at 105°C.
Radial lead type :
Lead free flow soldering condition correspondence.
Compliant to the RoHS directive (2011/65/EU).
LS
LF
Long Life
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C
Rated Voltage Range
2.5 to 16V
Rated Capacitance Range
100 to 1500μF
Capacitance Tolerance
± 20%
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
at 120Hz, 20°C
Less than or equal to the specified value.
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 5000 hours at 105°C.
1.25
1.25
(100kHz)
1)
ESR (
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Damp Heat
(Steady State)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
ESR (
1)
Leakage current ( 2)
Resistance to
Soldering Heat
After soldering the capacitor under the soldering conditions
prescribed here as preheat at 150 to 200°C for 60 to 180 seconds
and peak temperature at 265°C for 10 seconds or less, the
capacitor shall meet the specifications listed at right, provided that
its temperature profile is measured at both of terminal ends facing
the soldering side.
Marking
Navy blue print on the case top
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan b
ESR (
1)
Leakage current ( 2)
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 10V 270μF)
Resin coated Case
Capacitance
1
2
3
4
5
6
7
8
9 10 11 12
P L S 1 A 2 7 1 MDO 1
P ±0.5
qD±0.5
LS
270
A
941
Voltage(A:10V)
Size code
Configuration
Capacitance tolerance (±20%)
qd
Series
Lot. No.
L+0.5MAX.
15MIN
Rated capacitance (270μF)
4MIN
Rated voltage (10V)
Series name
Type
Size
qD
L
P
qd
q6.3 =9L q6.3 =10.5L q8 =7L
6.3
6.3
8.0
10.0
8.5
6.5
2.5
2.5
3.5
0.5
0.6
0.6
q8 =9L
8.0
8.5
3.5
0.6
(mm)
q8 =12L q10 =13L
8.0
10.0
11.5
12.5
3.5
5.0
0.6
0.6
Voltage
V
Code
2.5
4
6.3
10
16
e
g
j
A
C
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LS
series
Standard Ratings
Rated Voltage
(V)
code
2.5
(0E)
4
(0G)
6.3
(0J)
10
(1A)
16
(1C)
Surge Voltage
(V)
2.8
4.6
7.2
11.5
18.4
Rated Capacitance
(μF)
Case Size
φD × L (mm)
tan δ
Rated Ripple
(mArms)
Part Number
330
6.3 × 9
0.08
500
680
8×7
0.08
340
8
4800
PLS0E331MCO8
15
3900
820
6.3 × 9
0.08
500
PLS0E681MC L 2
8
4800
820
8×9
0.08
PLS0E821MCO8
410
7
5200
820
8 × 12
PLS0E821MCO6
0.08
410
7
5800
1500
PLS0E821MDO1
10 × 13
0.08
750
8
5500
PLS0E152MDO1
270
6.3 × 9
0.08
500
8
4800
PLS0G271MCO8
560
8×7
0.08
448
15
3900
PLS0G561MC L 2
560
8×9
0.08
448
7
5200
PLS0G561MCO6
680
8 × 12
0.08
544
7
5800
PLS0G681MDO1
1200
10 × 13
0.08
960
8
5500
PLS0G122MDO1
330
6.3 × 10.5
0.08
416
20
3000
PLS0J331MDL4
390
8×7
0.08
491
15
3900
PLS0J391MCL2
470
8 × 12
0.08
592
7
5500
PLS0J471MDO1
Leakage Current
ESR (mΩ)
(μA)
(at 100kHz 20°C)
560
6.3 × 9
0.08
706
9
4300
PLS0J561MCO8
560
8×9
0.08
706
8
5000
PLS0J561MCO6
820
10 × 13
0.08
1033
8
5500
PLS0J821MDO1
150
6.3 × 10.5
0.08
300
20
3000
PLS1A151MDL4
270
8 × 12
0.08
540
8
4900
PLS1A271MDO1
470
10 × 13
0.08
940
8
5500
PLS1A471MDO1
100
6.3 × 10.5
0.08
320
24
2800
PLS1C101MDL4
270
8 × 12
0.08
864
9
4500
PLS1C271MDO1
330
10 × 13
0.08
1056
9
4700
PLS1C331MDO1
470
10 × 13
0.08
1504
9
4700
PLS1C471MDO1
Rated ripple current (mArms) at 105°C 100kHz
No marked, 1
: In this case,
: In this case,
: In this case,
: In this case,
will be put at 12th digit of type numbering system.
2 will be put at 12th digit of type numbering system.
4 will be put at 12th digit of type numbering system.
6 will be put at 12th digit of type numbering system.
8 will be put at 12th digit of type numbering system.
Please refer to page 20, 21, 22 about the formed or taped product spec.
Please refer to page 3 for the minimum order quantity.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LV
Radial Lead Type, Long Life Assurance
series
High voltage (to 100V), Low ESR, High ripple current.
Long life of 3000 hours at 105°C.
Radial lead type:
Lead free flow soldering condition correspondence.
Compliant to the RoHS directive (2011/65/EU).
LX
LV
High Temperature
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C
Rated Voltage Range
16 to 100V
Rated Capacitance Range
6.8 to 470μF
Capacitance Tolerance
± 20%
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
at 120Hz, 20°C
Less than or equal to the specified value.
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 3000 hours at 105°C.
1.25
1.25
(100kHz)
Capacitance change
tan b
ESR (
Capacitance change
tan b
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Damp Heat
(Steady State)
1)
Leakage current ( 2)
ESR (
1)
Leakage current ( 2)
Resistance to
Soldering Heat
After soldering the capacitor under the soldering conditions
prescribed here as preheat at 150 to 200°C for 60 to 180 seconds
and peak temperature at 265°C for 10 seconds or less, the
capacitor shall meet the specifications listed at right, provided that
its temperature profile is measured at both of terminal ends facing
the soldering side.
Marking
Navy blue print on the case top
Capacitance change
tan b
ESR (
1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 35V 82μF)
Resin coated Case
Capacitance
1
2
3
4
5
6
7
8
9
10 11
12
P L V 1 V 8 2 0 M D L 1
Size code
P±0.5
qD±0.5
LV
82
V
012
Voltage(V:35V)
Configuration
Capacitance tolerance (±20%)
qd
Series
Lot. No.
L+0.5MAX.
15MIN
Rated capacitance (82μF)
Rated voltage (35V)
4MIN
Series name
Type
Size
qD
L
P
qd
q8 =9L
8.0
8.5
3.5
0.6
(mm)
q8 =12L q10 =13L
10.0
8.0
12.5
11.5
5.0
3.5
0.6
0.6
Voltage
V
16
20
25
35
50
63
80
100
Code
C
D
E
V
H
J
K
2A
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LV
series
Standard Ratings
Rated Voltage
(V)
code
16
(1C)
20
(1D)
25
(1E)
35
(1V)
50
(1H)
63
(1J)
80
(1K)
Case Size
φD × L (mm)
tan δ
Leakage Current
(μA)
ESR (mΩ)
(at 100kHz 20°C)
Rated Ripple
(mArms)
Part Number
220
8×9
0.12
704
26
2100
PLV1C221MCL1
270
8 × 12
0.12
864
24
2500
PLV1C271MDL1
470
10 × 13
0.12
1504
23
2900
PLV1C471MDL1
150
8×9
0.12
600
27
2000
PLV1D151MCL1
220
8 × 12
0.12
880
25
2400
PLV1D221MDL1
330
10 × 13
0.12
1320
24
2800
PLV1D331MDL1
120
8×9
0.12
600
28
2000
PLV1E121MCL1
150
8 × 12
0.12
750
26
2400
PLV1E151MDL1
270
10 × 13
0.12
1350
25
2800
PLV1E271MDL1
56
8×9
0.12
392
29
1900
PLV1V560MCL1
82
8 × 12
0.12
574
27
2300
PLV1V820MDL1
150
10 × 13
0.12
1050
26
2700
PLV1V151MDL1
33
8×9
0.12
330
32
1900
PLV1H330MCL1
39
8 × 12
0.12
390
29
2200
PLV1H390MDL1
68
10 × 13
0.12
680
28
2600
PLV1H680MDL1
22
8×9
0.12
277
35
1800
PLV1J220MCL1
27
8 × 12
0.12
340
33
2100
PLV1J270MDL1
47
10 × 13
0.12
592
29
2600
PLV1J470MDL1
10
8×9
0.12
160
40
1700
PLV1K100MCL1
12
8 × 12
0.12
192
38
1900
PLV1K120MDL1
22
10 × 13
0.12
352
35
2300
PLV1K220MDL1
Surge Voltage Rated Capacitance
(μF)
(V)
18.4
23.0
28.7
40.2
57.5
72.4
92
8×9
0.12
136
45
1600
PLV2A6R8MCL1
10
8 × 12
0.12
200
42
1800
PLV2A100MDL1
18
10 × 13
0.12
360
38
2200
PLV2A180MDL1
6.8
100
(2A)
115
Rated ripple current (mArms) at 105°C 100kHz
Please refer to page 20, 21, 22 about the formed or taped product spec.
Please refer to page 3 for the minimum order quantity.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LX
Radial Lead Type, Long Life Assurance
series
High reliability, High voltage (to 50V).
Low ESR, High ripple current.
Long life of 3000 hours at 125°C.
Radial lead type:
Lead free flow soldering condition correspondence.
Adapted to the RoHS directive (2011/65/EU).
LX
Higher
Temperature
LV
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +125°C
Rated Voltage Range
16 to 50V
Rated Capacitance Range
22 to 390μF
Capacitance Tolerance
± 20%
Tangent of loss angle (tan b)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
at 120Hz, 20°C
Less than or equal to the specified value.
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+125°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at below shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 3000 hours at 125°C.
1.25
1.25
(100kHz)
Capacitance change
tan b
ESR (
Capacitance change
tan b
The specifications listed at below shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Damp Heat
(Steady State)
1)
Leakage current ( 2)
ESR (
1)
Leakage current ( 2)
Resistance to
Soldering Heat
After soldering the capacitor under the soldering conditions
prescribed here as preheat at 150 to 200°C for 60 to 180 seconds
and peak temperature at 265°C for 10 seconds or less, the
capacitor shall meet the specifications listed at below, provided
that its temperature profile is measured at both of terminal ends
facing the soldering side.
Marking
Navy blue print on the case top
Capacitance change
tan b
ESR (
1)
Leakage current ( 2)
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Less than or equal to the initial specified value
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Less than or equal to the initial specified value
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 35V 39μF)
Resin coated Case
Capacitance
1
2
3
4
5
6
7
8
9
10 11
12
P L X 1 V 3 9 0 M C L 1
Size code
P±0.5
qD±0.5
LX
39
V
023
Voltage(V:35V)
Configuration
Capacitance tolerance (±20%)
qd
Series
Lot. No.
L+0.5MAX.
15MIN
Rated capacitance (39μF)
Rated voltage (35V)
4MIN
Series name
Type
Size
qD
L
P
qd
q8 =9L
8.0
8.5
3.5
0.6
(mm)
q8 =12L q10 =13L
8.0
10.0
11.5
12.5
3.5
5.0
0.6
0.6
Voltage
V
16
20
25
35
50
Code
C
D
E
V
H
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
*(;+
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LX
series
Standard Ratings
Rated Voltage
(V)(code)
Surge Voltage
(V)
16
(1C)
18.4
20
(1D)
25
(1E)
35
(1V)
50
(1H)
23.0
28.7
40.2
57.5
ESR (mΩ)
(at 100kHz 20°C)
Rated Ripple
(mArms)
Rated Capacitance
(μF)
Case Size
φD × L (mm)
tan δ
Leakage Current
(μA)
150
8×9
0.12
480
26
2100
810
PLX1C151MCL1
220
8 × 12
0.12
704
25
2400
930
PLX1C221MDL1
390
10 × 13
0.12
1248
23
2900
1130
PLX1C391MDL1
120
8×9
0.12
480
27
2000
800
PLX1D121MCL1
150
8 × 12
0.12
600
26
2300
910
PLX1D151MDL1
270
10 × 13
0.12
1080
24
2800
1110
PLX1D271MDL1
82
8×9
0.12
410
28
2000
780
PLX1E820MCL1
120
8 × 12
0.12
600
27
2300
890
PLX1E121MDL1
180
10 × 13
0.12
900
25
2800
1080
PLX1E181MDL1
39
8 ×9
0.12
273
33
1800
720
PLX1V390MCL1
56
8 × 12
0.12
392
31
2100
830
PLX1V560MDL1
100
10 × 13
0.12
700
28
2700
1040
PLX1V101MDL1
22
8×9
0.12
220
35
1800
700
PLX1H220MCL1
27
8 × 12
0.12
270
33
2000
810
PLX1H270MDL1
47
10 × 13
0.12
470
29
2600
1020
PLX1H470MDL1
Ambient temperature of a capacitor
Part Number
Rated ripple current (mArms) at 105°C 100kHz
Please refer to page 20, 21, 22 about the formed or taped product spec.
Please refer to page 3 for the minimum order quantity.
*(;+