CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LF Radial Lead Type, Standard series Low ESR, High ripple current. Load life of 2000 hours at 105°C. Radial lead type : Lead free flow soldering condition correspondence. Compliant to the RoHS directive (2011/65/EU). LS LG Higher Capacitance Long Life LF Low ESR LE Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 2.5 to 25V Rated Capacitance Range 6.8 to 1500µF Capacitance Tolerance ± 20% Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( Less than or equal to the specified value at 100kHz, 20°C 1) Leakage Current ( 2) at 120Hz, 20°C Less than or equal to the specified value. .25 1 1.25 After 2 minutes' application of rated voltage at 20°C Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C Z– 55°C / Z+20°C (100kHz) Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C. Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Resistance to Soldering Heat After soldering the capacitor under the soldering conditions prescribed here as preheat at 150 to 200°C for 60 to 180 seconds and peak temperature at 265°C for 10 seconds or less, the capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing the soldering side. Marking Navy blue print on the case top Capacitance change tan δ Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value ESR ( 1) Leakage current ( 2) ESR ( 1) Leakage current ( 2) ESR ( 1) Leakage current ( 2) 1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions Type numbering system (Example : 4V 560µF) Resin coated Case Capacitance 1 2 3 4 5 6 7 8 9 10 11 12 P L F 0 G 5 6 1 MDO 1 P ±0.5 φD±0.5 LF 560 g 841 Voltage(g:4V) Size code Configuration Capacitance tolerance (±20%) φd Series Lot. No. L+0.5MAX. 15MIN Rated capacitance (560µF) 4MIN Rated voltage (4V) Series name Type Size φD L P φd φ6.3 × 6L φ6.3 × 9L φ6.3 × 10.5L φ8 × 7L 6.3 6.3 6.3 8.0 5.5 8.5 10.0 6.5 2.5 2.5 2.5 3.5 0.45 0.6 0.5 0.6 φ8 × 9L 8.0 8.5 3.5 0.6 (mm) φ8 × 12L φ10 × 8L φ10 × 10L φ10 × 13L 8.0 10.0 10.0 10.0 11.5 7.5 9.5 12.5 3.5 5.0 5.0 5.0 0.6 0.6 0.6 0.6 Voltage V 2.5 4 Code e g 6.3 10 16 20 25 j A C D E Please refer to page 20 about the end seal configuration. Dimension table in next page. CAT.8100D-1 CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LF Standard Ratings series Rated Voltage (V)(code) 2.5 (0E) 4 (0G) 6.3 (0J) 10 (1A) 16 (1C) 20 (1D) 25 (1E) Surge Voltage (V) 2.8 4.6 7.2 11.5 18.4 23 28.7 Rated Capacitance (µF) Case Size φD × L (mm) tan δ Rated Ripple (mArms) Part Number 330 6.3 × 9 0.08 500 390 6.3 × 10.5 0.08 195 7 5600 PLF0E331MCO8 20 3200 560 6.3 × 9 0.08 500 PLF0E391MDL4 7 5600 PLF0E561MCO8 560 8×9 0.08 680 8×9 0.08 280 6 4800 PLF0E561MCO1 340 7 4800 680 8 × 12 PLF0E681MCO6 0.08 340 6 5700 PLF0E681MDO1 Leakage Current ESR (mΩ) (µA) (at 100kHz 20°C) 820 6.3 × 9 0.08 500 7 5600 PLF0E821MCO8 820 8×9 0.08 410 7 5200 PLF0E821MCO6 820 8 × 12 0.08 410 6 6200 PLF0E821MDO1 1000 10 × 13 0.08 500 6 6500 PLF0E102MDO1 1200 10 × 13 0.08 600 8 5300 PLF0E122MDO1 1500 8 × 12 0.08 750 7 6100 PLF0E152MDO6 1500 10 × 13 0.08 750 8 5500 PLF0E152MDO1 270 6.3 × 9 0.08 500 7 5600 PLF0G271MCO8 270 6.3 × 10.5 0.08 216 20 3200 PLF0G271MDL4 390 6.3 × 10.5 0.08 312 24 3300 PLF0G391MDL4 560 8×9 0.08 448 7 5200 PLF0G561MCO6 560 8 × 12 0.08 448 7 5500 PLF0G561MDO1 680 8 × 12 0.08 544 6 6200 PLF0G681MDO1 820 10 × 13 0.08 656 6 6500 PLF0G821MDO1 1000 10 × 13 0.08 800 6 6640 PLF0G102MDO1 1200 10 × 13 0.08 960 8 5600 PLF0G122MDO1 220 6.3 × 10.5 0.08 277 20 3200 PLF0J221MDL4 330 6.3 × 10.5 0.08 416 24 3300 PLF0J331MDL4 470 8×9 0.08 592 7 5200 PLF0J471MCO6 470 8 × 12 0.08 592 7 5500 PLF0J471MDO1 680 10 × 13 0.08 857 6 6300 PLF0J681MDO1 47 6.3 × 10.5 0.08 94 25 2900 PLF1A470MDL4 68 6.3 × 10.5 0.08 136 25 2900 PLF1A680MDL4 100 6.3 × 10.5 0.08 200 25 2900 PLF1A101MDL4 150 6.3 × 10.5 0.08 300 25 2900 PLF1A151MDL4 270 8 × 12 0.08 540 8 4900 PLF1A271MDO1 470 10 × 13 0.08 940 7 5700 PLF1A471MDO1 560 10 × 13 0.08 1120 7 5900 PLF1A561MDO1 680 10 × 13 0.08 1360 7 6100 PLF1A681MDO1 100 6.3 × 10.5 0.08 320 24 2900 PLF1C101MDL4 180 8 × 12 0.08 576 9 5000 PLF1C181MDO1 270 8 × 12 0.08 864 9 5100 PLF1C271MDO1 330 10 × 13 0.08 1056 9 6100 PLF1C331MDO1 470 10 × 13 0.08 1504 9 6100 PLF1C471MDO1 22 6.3 × 6 0.12 88 50 1700 PLF1D220MCL2 39 8×7 0.12 156 45 2000 PLF1D390MCL2 47 8×7 0.12 188 45 2000 PLF1D470MCL2 56 10 × 8 0.12 224 40 2400 PLF1D560MCL2 68 10 × 8 0.12 272 40 2600 PLF1D680MCL2 82 10 × 8 0.12 328 40 2600 PLF1D820MCL2 PLF1D101MDO2 100 8 × 12 0.12 400 22 3320 120 10 × 10 0.12 480 35 2800 PLF1D121MCL2 150 10 × 13 0.12 600 20 4320 PLF1D151MDO2 6.8 6.3 × 6 0.12 85 80 1200 PLF1E6R8MCL2 10 6.3 × 6 0.12 125 65 1500 PLF1E100MCL7 10 8×7 0.12 125 60 1500 PLF1E100MCL2 22 8×7 0.12 275 50 1800 PLF1E220MCL7 47 10 × 13 0.12 588 30 3000 PLF1E470MDO2 56 10 × 13 0.12 700 28 3800 PLF1E560MDO2 Parts with 5000h guaranteed life are also available upon request. Please refer to page 20, 21, 22 about the formed or taped product spec. Please refer to page 3 for the minimum order quantity. No marked, 1 : In this case, : In this case, : In this case, : In this case, : In this case, will be put 2 will be 4 will be 6 will be 7 will be 8 will be Rated ripple current (mArms) at 105°C 100kHz at 12th digit of type numbering system. put at 12th digit of type numbering system. put at 12th digit of type numbering system. put at 12th digit of type numbering system. put at 12th digit of type numbering system. put at 12th digit of type numbering system. CAT.8100D-1