CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LS Radial Lead Type, Long Life Assurance series Ultra-low ESR, High ripple current. Load life of 5000 hours at 105°C. Radial lead type : Lead free flow soldering condition correspondence. Compliant to the RoHS directive (2011/65/EU). LS LF Long Life Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 2.5 to 16V Rated Capacitance Range 100 to 1500µF Capacitance Tolerance ± 20% Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( Less than or equal to the specified value at 100kHz, 20°C 1) Leakage Current ( 2) at 120Hz, 20°C Less than or equal to the specified value. .25 1 1.25 After 2 minutes' application of rated voltage at 20°C Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C Z– 55°C / Z+20°C (100kHz) Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 5000 hours at 105°C. Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Resistance to Soldering Heat After soldering the capacitor under the soldering conditions prescribed here as preheat at 150 to 200°C for 60 to 180 seconds and peak temperature at 265°C for 10 seconds or less, the capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing the soldering side. Marking Navy blue print on the case top Capacitance change tan δ Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value ESR ( 1) Leakage current ( 2) ESR ( 1) Leakage current ( 2) ESR ( 1) Leakage current ( 2) 1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions Type numbering system (Example : 10V 270µF) Resin coated Case Capacitance 1 2 3 4 5 6 7 8 9 10 11 12 P L S 1 A 2 7 1 MDO 1 P ±0.5 φD±0.5 LS 270 A 941 Voltage(A:10V) Size code Configuration Capacitance tolerance (±20%) φd Series Lot. No. L+0.5MAX. 15MIN Rated capacitance (270µF) 4MIN Rated voltage (10V) Series name Type Size φD L P φd φ6.3 × 9L φ6.3 × 10.5L φ8 × 7L 6.3 6.3 8.0 8.5 10.0 6.5 2.5 2.5 3.5 0.6 0.5 0.6 φ8 × 9L 8.0 8.5 3.5 0.6 (mm) φ8 × 12L φ10 × 13L 8.0 10.0 11.5 12.5 3.5 5.0 0.6 0.6 Voltage V 2.5 4 6.3 10 16 Code e g j A C Please refer to page 20 about the end seal configuration. Dimension table in next page. CAT.8100D CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LS series Standard Ratings Rated Voltage (V) code 2.5 (0E) 4 (0G) 6.3 (0J) 10 (1A) 16 (1C) Surge Voltage (V) 2.8 4.6 7.2 11.5 18.4 Leakage Current ESR (mΩ) (µA) (at 100kHz 20°C) Rated Capacitance (µF) Case Size φD × L (mm) tan δ Rated Ripple (mArms) Part Number 330 6.3 × 9 0.08 500 680 8×7 0.08 340 8 4800 PLS0E331MCO8 15 3900 820 6.3 × 9 0.08 500 PLS0E681MC L 2 8 4800 820 8×9 0.08 PLS0E821MCO8 410 7 5200 820 8 × 12 PLS0E821MCO6 0.08 410 7 5800 1500 PLS0E821MDO1 10 × 13 0.08 750 8 5500 PLS0E152MDO1 270 6.3 × 9 0.08 500 8 4800 PLS0G271MCO8 560 8×7 0.08 448 15 3900 PLS0G561MC L 2 560 8×9 0.08 448 7 5200 PLS0G561MCO6 680 8 × 12 0.08 544 7 5800 PLS0G681MDO1 1200 10 × 13 0.08 960 8 5500 PLS0G122MDO1 330 6.3 × 10.5 0.08 416 20 3000 PLS0J331MDL4 390 8×7 0.08 491 15 3900 PLS0J391MCL2 470 8 × 12 0.08 592 7 5500 PLS0J471MDO1 6.3 × 9 0.08 706 9 4300 PLS0J561MCO8 560 8×9 0.08 706 8 5000 PLS0J561MCO6 820 10 × 13 0.08 1033 8 5500 PLS0J821MDO1 150 6.3 × 10.5 0.08 300 20 3000 PLS1A151MDL4 270 8 × 12 0.08 540 8 4900 PLS1A271MDO1 470 10 × 13 0.08 940 8 5500 PLS1A471MDO1 100 6.3 × 10.5 0.08 320 24 2800 PLS1C101MDL4 270 8 × 12 0.08 864 9 4500 PLS1C271MDO1 330 10 × 13 0.08 1056 9 4700 PLS1C331MDO1 470 10 × 13 0.08 1504 9 4700 PLS1C471MDO1 560 Rated ripple current (mArms) at 105°C 100kHz No marked, 1 : In this case, : In this case, : In this case, : In this case, will be put at 12th digit of type numbering system. 2 will be put at 12th digit of type numbering system. 4 will be put at 12th digit of type numbering system. 6 will be put at 12th digit of type numbering system. 8 will be put at 12th digit of type numbering system. Please refer to page 20, 21, 22 about the formed or taped product spec. Please refer to page 3 for the minimum order quantity. CAT.8100D