PDF

ALUMINUM ELECTROLYTIC CAPACITORS
CJ
Chip Type, High Reliability.
Low temperature ESR specification.
series
Chip type, high temperature range, for +125°C use.
Added ESR specification after the test at – 40°C
(φ6.3 sizes provide only for the first stage. )
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
CZ
CJ
Low ESR
Long Life
UB
Added ESR specification
at –40°C
Specifications
Item
Performance Characteristics
Category Temperature Range
–40 to +125°C
Rated Voltage Range
10 to 50V
Rated Capacitance Range
10 to 470µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 1 minute's application of rated voltage, leakage current is not more than 0.03CV or 4(µA) , whichever is greater.
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
tan δ (MAX.)
Tangent of loss angle (tan δ)
10
0.32
16
0.24
25
0.21
35
0.18
50
0.18
Measurement frequency : 120Hz
Rated voltage (V)
Impedance ratio
Z–40°C / Z+20°C
ZT / Z20 (MAX.)
Stability at Low Temperature
10
16
25
35
50
12
8
6
4
4
Capacitance change
tan δ
Leakage current
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 125°C.
Endurance
Within ±30% of the initial capacitance value
300% or less than the intial specified value
Less than or equal to the initial specified value
After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds,
Within ±10% of the initial capacitance value
Capacitance change
which is maintained at 250°C. The capacitors shall meet
Less than or equal to the initial specified value
tan δ
the characteristic requirements listed at right when they
Less than or equal to the initial specified value
Leakage current
are removed from the plate and restored to 20°C.
Shelf Life
Resistance to soldering
heat
Black print on the case top.
Marking
Chip Type
Type numbering system (Example : 10V 100µF)
L ± 0.3
C ± 0.2
0.3MAX.
7
8
9 10 11 12 13 14
Taping code
Capacitance tolerance (±20%)
Rated capacitance (100µF)
Rated voltage (10V)
Series name
Type
(mm)
φD × L
A
B
C
E
L
H
A ±0.2
Capacitance
E
B ±0.2
A2
100V
CJ
φD ±0.5
Series
Lot No.
6
Positive
Plastic platform
Trade mark
5
Configuration
A ±0.2
(φ8 to φ10)
4
Negative
H
Voltage( V : 35V )
3
A ± 0.2 A ± 0.2
E
B ± 0.2
Capacitance
Lot No.
C ± 0.2
0.3MAX.
φD ±0.5
A2
47C
CJ
Series
2
UC J 1 A 1 0 1 MCL 1 GS
0.5MAX.
Plastic platform
Voltage( C : 16V )
1
Positive
0.5MAX.
(φ6.3)
L ± 0.5
Negative
H
6.3 × 8.7 8 × 10 10 × 10
2.4
2.9
3.2
6.6
8.3
10.3
6.6
8.3
10.3
2.2
3.1
4.5
8.7
10
10
0.5 to 0.8 0.8 to 1.1 0.8 to 1.1
Rated Voltage
V
Code
10
A
16
C
25
E
35
V
50
H
Dimensions
Cap.(µF)
10
22
33
47
100
220
330
470
10
1A
V
Code
100
220
330
470
101
221
331
471
6.3 × 8.7
8 × 10
10 × 10
10 × 10
14
2.0
1.5
1.5
16
1C
95
6.0 250
4.5 400
4.5 400
6.3 × 8.7
8 × 10
10 × 10
10 × 10
14
2.0
1.5
1.5
25
1E
95
6.0 250
4.5 400
4.5 400
6.3 × 8.7
6.3 × 8.7
6.3 × 8.7
8 × 10
10 × 10
10 × 10
14
14
14
2.0
1.5
1.5
6.3 × 8.7
95 6.3 × 8.7
95 6.3 × 8.7
95 6.3 × 8.7
6.0 250 10 × 10
4.5 400 10 × 10
4.5 400
35
1V
14
14
14
14
1.5
1.5
95 6.3 × 8.7
95 6.3 × 8.7
8 × 10
95
95 10 × 10
4.5 400 10 × 10
4.5 400 Case size
φD× L
(mm)
50
1H
14
14
2.0
1.5
1.5
95
95
6.0 200
4.5 330
4.5 330
after
Initial endurance
test
ESR
Rated
ripple
Max. ESR (Ω) at -40°C 100kHz, Rated ripple current (mArms) at 125°C 100kHz
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.35
120 Hz
0.50
300 Hz
0.64
1 kHz
0.83
10 kHz or more
1.00
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please refer to page 3 for the minimum order quantity.
CAT.8100D