M63151FP Polygon Scanner Motor Driver (DMOS Driver) REJ03F0028-0100Z Rev.1.0 Sep.16.2003 Description The M63151FP is a driver and controller for use with three-phase brushless motor. A DMOS element with high withstand voltage and low levels of switching loss is used on each output. Acceleration and deceleration inputs are operable at TTL levels. Features • • • • • • • Power-supply voltage (max.): 30 V Output current (max.): 2.5 A RDS (typ.): 140 Ω (total of the upper and lower DMOS FETs) Built-in chip circuit for preventing through current in commutation Built-in chip comparator for current detection Buil-in chip overheating protection circuit Built-in chip motor-lock protection circuit Applications • OA equipment such as LBPs, copiers, and fax machines Block diagram PS TEST Vboot Hw Hv Hw+ Hv+ Hw- Hv- Hu Hu+ VCC HuRegulator 12V / 6V VREG cp2 cp1 Frequency Generator Power Save TSD HallAmp Motor Lock Protection PWM PWM ON/OFF Synhro-PWM CRLP Pre - driver MOTOR ON/OFF RLP U V W Charge Pump /ACC /DEC RCP Rev.1.0, Sep.16.2003, page 1 of 13 CPout Pref Rfc Cfc RNF RS GND M M63151FP Pin Functions VCC VREG 1 42 2 41 CP2 3 40 4 39 5 38 6 37 7 36 8 35 9 34 10 33 11 32 12 31 13 30 14 29 15 28 16 27 17 26 18 25 19 24 20 23 21 22 Vboot NC W V GND N.C. RS U RNF GND N.C. HwHw+ Pref CPout /ACC /DEC RLP CRLP TEST PS GND N.C. Cfc Rfc RCP Hu+ HuHv+ Hv- Package outline (42P9R) Description of Pin Functions Pin No. Pin Name Description Pin No. Pin Name Description 1 2 3 VCC VREG cp2 Motor power supply Internal power supply Pin 2 for connection of the step-up voltage capacitor 42 41 40 Pref CPout / ACC PWM control voltage input Charge-pump output Input: request for acceleration 4 cp1 Pin 1 for connection of the step-up voltage capacitor 39 / DEC Input: request for deceleration 5 Vboot Stepped-up voltage power-supply (internal) 38 RLP Resistor connection pin for lock protection 6 N.C. Open 37 CRLP Capacitor connection pin for lock protection 7 W W-phase drive output 29 N.C. Open 8 V V-phase drive output 36 TEST Test pin (Tj detection) 9 to 13 GND Ground 35 PS Power-save switchover 14 N.C. Open 30 to 34 GND Ground 15 Rs Output of detected current 28 Cfc For connecting the resistor used to set the PWM cycle 16 U U-phase drive output 27 Rfc For connecting the capacitor used to set the PWM cycle 17 Rss Current detection 26 RCP Charge-pump output current setting 18 GND Ground 25 Hu+ Hall signal input pin 19 N.C. Open 24 Hu- Hall signal input pin 20 Hw- Hall signal input pin 23 Hv+ Hall signal input pin 21 Hw+ Hall signal input pin 22 Hv- Hall signal input pin Rev.1.0, Sep.16.2003, page 2 of 13 M63151FP Absolute Maximum Ratings (Ta = 25°C) No. Item Symbol Rated Value Unit 1 2 3 4 5 Power-supply voltage Output current Hall-sensor amp. differential input range Voltage on input pins Allowable dissipation Vcc lpeak VHA Vin Pd 30 3.0 4.5 −0.3 to 7 2.5 V A V V W 6 7 Parameter for thermal derating Conjunction temperature Kθ Tj 25 150 mW / °C °C 8 Ambient temperature during operation Ta −20 to °C Remarks / ACC, / DEC, / PS, Pref During start-up at Ta = 60°C, with the device mounted on an iron substrate +75 9 Temperature during storage Tstg −40 to °C +125 Thermal derating 6.0 Allowable power dissipation (Pdp) (W) With the A-type board: 4.7 W 5.0 With the B-type board: 3.4 W 4.0 With the C-type board: 2.8 W 3.0 2.0 1.0 0 25 50 75 100 Ambient Temperature (Ta) Note: 125 150 (˚C) The large values for allowable power dissipation make it possible to use this device without a heat sink. At the very least, dissipation of 2.8 W is possible with a glass-epoxy single-layered board, and 4.7 W is obtained by applying special design measures to the board. For details on the configurations of boards A, B, and C, refer to ‘Boards used in the evaluation of thermal dating’ on page 11. Rev.1.0, Sep.16.2003, page 3 of 13 M63151FP Electrical Characteristics (DC) (Unless otherwise noted, Ta = 25°C, Vcc = 24 V) Item Symbol Rated Values Unit Conditions of Measurement and Remarks Min. Typ. Max. Output DMOS on-resistance RDS — 1.40 2.20 Ω Total of on-resistance for upper and lower DMOS FET Iout = 1.0 A Power-supply voltage range Circuit current with no signal RNF pin threshold voltage Vcc lcc VRNF 21.6 — 212 24.0 5.4 250 26.4 10.0 288 V mA mV PREF threshold voltage Vpref 1.00 1.25 1.50 V PREF voltage that satisfies RS current > 1 mA /ACC input current H /ACC input current L IACCH IACCL –1.0 –50 — –10 1.0 — / ACC = 5V / ACC = 0V /DEC input current H IDECH — 250 500 /DEC input current L Acceleration current IDECL ISS –50 –240 –10 –200 — –160 µA µA µA µA µA Deceleration current ISD 160 200 240 µA / ACC = Hi, / DEC = Lo, Rcp = 12KΩ at CPout = 2.0 V Detent current IZ –100 0 +100 nA / ACC =5V, / DEC = Hi or Lo, at CPout =2.0 V CPout output voltage range VCPout 0.85 — 3.90 V Less than the min. rated value when / ACC = 5 V, / DEC = 0 V; More than the max. rated value when / ACC = 0 V, / DEC = 5 V Output leakage current I leak –100 0 100 µA Hall-sensor amp. same-phase input voltage range VHA1 1.5 — Vcc–2 V Hall-sensor amp input current IHA — 0.5 4.0 µA Hµ+ = Hµ, Hv+ = Hv, Hw+ = Hw– Hall-sensor amp input voltage hysteresis Vhys 6.95 11.0 15.45 mV Between Hµ+ and Hµ–, Hv+ and Hv–, and HW+ and HW- Hall-sensor amp. min. input amplitude for operation VHA2 50 — — mV Between Hµ+ and Hµ–, Hv+ and Hv–, and Hw+ and Hw–; The amplitude that satisfies phase delay < 5 deg for the above variation of hysteresis voltage PREF input current IPref –100 10 100 nA Pref = 2.5 V Rev.1.0, Sep.16.2003, page 4 of 13 PS = 0 V / ACC = 5V / ACC = 0V / ACC = Lo, / DEC = Hi, Rcp = 12KΩ at CPout = 2.0 V M63151FP Electrical Characteristics (AC) (Unless otherwise noted, Ta = 25°C, Vcc = 24 V) Item Symbol Rated Values Unit Measurement Conditions and Remarks Min. Typ. Max. Delay from turning on to output Delay from turning off to output Tdon — 1.0 1.5 µS Tdoff — 0.5 1.0 µS Frequency of Fc oscillation Fc 17.3 21.6 25.9 KHz When RfC = 24 KΩ , Cfc = 470 pF Time for motor-lock protection to operate TML - ON 10.0 — 20.0 SEC Between RLP and CRLP, 4.7 MΩ, between CRLP and GNDE, 1 µF, load for resistors U, V, W: 2R = 10 Ω Time to resume after motor-lock protection TML - OFF 10.0 — 20.0 SEC As above Unit Measurement Conditions and Remarks Items for Confirmation in Evaluation Item Overheating shutdown operating temperature Overheating shutdown temperature hysteresis Symbol Rated Values Min. Typ. Max TSG - ON — 160 — °C TSD - OFF — 30 — °C Temperature for resumption after reaching the shutdown operating temperature Note: Operation of the device within the above TSD operating temperature range is not guaranteed. The guaranteed operation range of the device is up to Tjmax, that is, the absolute max. rating. The TSD operation is thus activation of the thermal protection circuit when Tjmax has been exceeded by mistake. Accordingly, the device must be operated at Tj = 150°C or below. Rev.1.0, Sep.16.2003, page 5 of 13 M63151FP Precautions during Use Protection from overheating: The impedance between the power supply and output pins of the circuit board is low when the IC is in use. Contingencies such as the application of excessive voltage by voltage surges may lead to short-circuits forming between the output pins of the IC can lead to damage which includes destruction of the TSD module. The chip is then liable to catch fire. Accordingly, we strongly recommend that you consider the application of safety measures such as fuses. Dissipation of heat: Sufficient thermal evaluation must be performed before changes to the thermal environment (including power-supply voltage, output current, the circuit board, etc.). The new design must be brought within the margins for thermal dissipation. Also, note that a higher carrier frequency setting leads to a larger level of IC-internal switching loss. Wiring on the board: Within the IC, the output current flows through the current-sense resistor (in the 0.17-Ω level), and current control is applied when a fall in this voltage is detected. Also, since the flow of output current is for a high-speed switching operation, take care to avoid the generation of crosstalk between the wiring which carries the current and the wiring which is connected to the high-impedance input pins (Hall output), etc. The motor-lock protection circuit: Holding of the motor by some external or other factor leads to a continuous flow of the maximum current to the IC. The IC is thus equipped with a module that detects this condition; at specified intervals after the condition has been detected, the module stops the flow of current to the motor and automatically attempts to resumes operation. The time constant set by the resistor and capacitor which are externally connected to pins 37 and 38 determines the time from when the maximum current begins to flow until the motor is stopped; the same R and C values set the time from stopping to restarting of the motor. Make sure that the specified interval is longer than the time the motor takes to start up. When the motor characteristics and setting for maximum current are such that the maximum current is exceeded when the duty cycle is 75% (RS voltage high period: low period = 3:1) or more, the IC judges that the maximum current is not continuously flowing. In such a case, this protection circuit does not operate. If the IC junction temperature rises before or during the operation of this protective circuit, the overheat-protection circuit operation takes precedence. Short circuits between output pins and adjacent pins This IC does not incorporate protection against short-circuits between pins. An attempt to output a current while there is a short-circuit between an output and VCC or ground, an output and VREG, or VCC and VREG may cause an overcurrent to flow; this may adversely affect the IC. Rev.1.0, Sep.16.2003, page 6 of 13 M63151FP M63151FP PWM control method A triangular waveform is output on the CFC pin under the control of the values of the external capacitor connected to Cfc and the external resistor connected to Rfc. The PWM duty cycle is determined through comparison of this voltage with the control voltage determined by the current output from CPout and the external filter connected to the CPout and PREF pins, i.e. the voltage on PREF. That is, PWM-ON is satisfied when the triangular waveform is at a level below the control voltage and PWM-OFF is satisfied (regenerative) when the triangular waveform rises above the control voltage. How the relation between the voltages on Cfc and Pref determines the output voltage is depicted below. Cfc output voltage VPREF (control voltage) → PREF threshold voltage → PWM - Duty cycle → High:PWM - ON Low:PWM - OFF VPREF Operating range Min.0.85 V less to max.4.00 V or more (a) When VPREF < 1.25 V, PWM duty cycle = 0% (always regennerative) (b) When1.25 V < VPREF < 3.75 V, PWM control (c) When3.75 V < VPREF, PWM duty cycle =100% Cfc output waveform rage Peak = 3.75 V Trough = 1.25 V (a) Minimum voltage: 1.25 V ±0.25 V (b) Maximum voltage: 3.75 V ±0.25 V VPREFthrehold voltage (VtPREF) 1.25V ± 0.25 V (a) When VPREF< VtVPREF, motor ison (b) When VPREF< VtVPREF, motor is always off. While the motor is rotating, the Cfc output voltage is driven low with the same timing as switching of phase for the motor in order to improve changes in the rotation speed. Therefore, the voltage waveform output on Cfc during actual motor operation is as shown in the following figure. Phase U The dashed lines indicate the timing of phase switching. Phase V Phase W The hold line shows the PWM output voltage wavform. → 3.75 V VPREF Cfc output voltage → 1.25 V → 0V Rev.1.0, Sep.16.2003, page 7 of 13 M63151FP Motor-Lock Protection Circuit (1) As well as the overheating protection function, this IC incorporates a module that turns off current to the motor after the motor has been mechanically held over a specified period. This prevents overheating. The operating conditions of this module and a timing chart that depicts its operation are given below. Note, however, that when the IC does become overheated, the overheating protection circuit still operates because it takes precedence over the lock protection function. (1) Conditions of operation (a) The RS current detection resistor detects a continuous flow of the limit current (in practice, the current-limiting circuit leaves the IC operating as long as the voltage on RS stays within the range 0 to 0.25 V). (b) Normally, the period at 0 V in item (a) will be 3.5 µs, and this is approximately equal to the period at 0.25 V. However, this circuit does not operate when motor characteristics, etc. mean that the period at 0.25 V is three times the period at 0 V (duty cycle = 75%) or longer. (c) The period of the lock-protection circuit operations (the period from locking of the motor to the time when current to the motor is stopped) is determined by the time constant set up by the capacitor and resistor externally connected to pins 37 (CRLP) and 38 (RLP). (d) After the motor has been turned off, automatic resumption is attempted at a time determined by the same R and C values as in point (c). External signals are not accepted until resumption. (2) Block diagram VREG(6V) VREG ↓I1 Comp2 Comp1 A + RNF 17 C1 - 1V 0.25V Current - Limiting control signal + RFP 38 Hi: PWM-ON Lo: PWM-OFF (Regeneration) R=4.7M Ω CRLP 37 + Lock protection 5.4V or 4V circuit control signal 1.2 Comp4 Hi: Normal operation Low: MOTOR - lock protection circuit 0.25V C=1µF Comp3 RNF 0 POINT A 4V 1V Current limiting control signal Comp3 output 0.7V 0 When the maximum current no longer flows to the RNF, the CRLP voltage is driven low to cancel the protective finction. 5.4V CRLP Lock protection circuit Currnt flows to control signal the motor ↑Initiation Rev.1.0, Sep.16.2003, page 8 of 13 1.2V Flow of current to the motor stops Currnt flows to the motor M63151FP Motor Lock Protection Circuit (2) The time intervals in the block diagram on the previous page are set up in the following ways. (1) Current-limiting control signal low period The flow of the limiting current to the RNF pin is detected, and the motor is regenaratively operated over the period indicated below: Toff = C1 x V1 ÷ LI = 17.5pF x 1V ÷ 6.25 µA = 2.8 µs Note, however, that a delay time of about 0.5 µs from the time when the high-side or low-side of a phase is turned off to the time when the output of the opposite side is turned on is set in the pre-drive stage of output. This prevents through current to and from upper and lower transistors within the same phase. Accordingly, the output voltage off period (regenerative time) is 0.5 µs plus the result of the above calculation, which is about 3.3 µs. (2) Operation time of the motor-lock protection circuit The following equation gives the time from locking of the motor to stoppage of current flow. TML-ON = C x R x ln ((Vreg – R x I) ÷ ((Vreg – R x I) – V3)) = 1 µF x 4.7 MΩ x ln ((6 V – 4.7 MΩ x 17 nA ÷ ((6 V – 4.7 MΩ x 17 nA) – 5.4V)) = 11.42 s Similarly, the period from the time when the motor is turned off to automatic resumption is: TML-OFF = C x R x ln ((V3 – 0.7 V – R x I) ÷ (V4-7V)) = 1 µF x 4.7 MΩ x ln (5.4 V – 0.7 V – 4.7 MΩ x 17 nA ÷ 1.2 V – 0.7 V) = 10.45 s Rev.1.0, Sep.16.2003, page 9 of 13 M63151FP Timing chart: motor output current / Hall input Hall sensor input Note: Hall sennsor input. Bold lines are positive phase. Hu + Hu− Hv− Hv + Hw + Output voltage (Duty cycle = 100%) Hw− Outward flow U Inward flow Outward flow V Inward flow Outward flow W Output voltage (Duty cycle = 30%) Inward flow Outward flow U Inward flow Outward flow V Inward flow Outward flow W Inward flow 0 180 360 540 Inward flow QE (degrees) 720 * : The above waveforms represent the tinming, and are not the same a the waveforms seen in actual operation of the motor. Rev.1.0, Sep.16.2003, page 10 of 13 M63151FP Boards used in the evaluation of thermal derating Board material layer 1 [TOP view] Glass-epoxy FR - 4 Size 70 × 70 mm 1 42 21 22 1 42 21 22 A - Typeboard thickness t = 1.6 mm [layer 2] 1&2 layer material: cupper thichness: t = 18 µm B - Typeboard [layer 2] 1 42 21 22 C - Typeboard [layer 1] POWER-SSOP TOP VIEW BOTTOM VIEW mounted Evaluation board Rev.1.0, Sep.16.2003, page 11 of 13 layer 2 [rear view] M63151FP Sample circuit application 100µF 1 VCC PREF 42 0.03µF 24V 2 VREG CPOUT41 300 K Ω 0.01µF 0.1µF 3 CP2 /ACC 40 4 CP1 / D E C 39 5 Vboot 0.33µF RLP 38 4.7MΩ 6 N.C. CRLP 37 7 W TEST 36 8 V PS 35 1.0µF 0.167Ω 14 N.C. N.C. 29 470pF 15 RS Cfc 28 16 U Rfc 27 17 RNF RCP 26 18 GND HU+ 25 19 N.C. HU- 24 20 HW- HV+ 23 21 HW+ HV - 2 2 1K Ω 24K Ω 100pF HW 12K Ω HV HU Rev.1.0, Sep.16.2003, page 12 of 13 HE G Z1 e 1 42 z y Detail G D b 21 22 JEDEC Code − x M A Weight(g) − F Detail F A2 Lead Material Cu Alloy c A1 A A1 A2 b c D E e HE L L1 z Z1 x y Symbol b2 e1 I2 b2 Dimension in Millimeters Min Nom Max − − 2.2 0 0.1 0.2 − − 2.0 0.27 0.32 0.37 0.23 0.25 0.3 17.5 17.3 17.7 8.4 8.6 8.2 − − 0.8 12.23 11.93 11.63 0.7 0.5 0.3 − − 1.765 − − 0.75 − 0.9 − − − 0.16 − − 0.1 − 0° 10° − − 0.5 − − 11.43 − − 1.27 Recommended Mount Pad e Plastic 42pin 450mil HSSOP e1 MMP L1 EIAJ Package Code HSSOP42-P-450-0.8 E Rev.1.0, Sep.16.2003, page 13 of 13 L l2 42P9R-C M63151FP Package Dimensions Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. http://www.renesas.com RENESAS SALES OFFICES Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500 Fax: <1> (408) 382-7501 Renesas Technology Europe Limited. Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900 Renesas Technology Europe GmbH Dornacher Str. 3, D-85622 Feldkirchen, Germany Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11 Renesas Technology Hong Kong Ltd. 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2375-6836 Renesas Technology Taiwan Co., Ltd. FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. 26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 © 2003. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon 1.0