PPM10-E-xxELF PPM-SERIES Rev.04-2012 10 Watt Univ. 85-264VAC (120-370VDC) Single Output Over Voltage Protection (out) 4 kV AC I/O Isolation Low Ripple and Noise High Efficiency Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PPM-Series are high efficiency green power moduls with various packaging provided by Peak. The features of this series are: wide input voltage, DC and AC all in one, high efficiency, high reliability, low loss, safety isolation etc. They are widely used in industrial, office and civil equipments.. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Input Voltage Range Input Frequency Input (Inrush) Current External Input Fuse (recommended) Output Specifications Voltage Accuracy Input variation Load variation (10-100%) Ripple and Noise (20Mhz bandwidth) Short Circuit Protection Over current protection Common Specifications Temperature range Power derating Case temperature Storage Hold up Time Humidity (non condensing) Temperature Coefficient Switching Frequency I/O Isolation Voltage Leakage current EMI / RFI conducted EMC compliance ESD RF EFT / bursts Surge Safety Standards Safety Approvals Safety Class Case Material Reliability Calculated MTBF (MIL-HDBK-217F) Weight 85 – 264 VAC or 120 – 370 VDC universal 47 – 440 Hz 110 VAC 230 VAC 230 mA (10A), typ. 150mA (20A), typ. 2A / 250V slow blow ±2%, typ (±3% at 3.3 Vout) ±0.5%, typ ±1% , typ 50mV pk-pk, typ Continuous, auto resume > 110% Io -25°C to +70 °C 2% / °C +95°C (max) -40°C to +105 °C 50mS, typ. (230VAC) 95%, max. 0.02%/°C 60kHz, typ 4000VAC / 1min. 0.1mA, typ EN55011, level B IEC/EN 61000-4-2 ±15kV/±8kV IEC/EN 61000-4-3 10V/m IEC/EN 61000-4-4 ±4 kV IEC/EN 61000-4-5 ±2kV/±4kV IEC60601, EN60601, UL60950 EN60601, UL60950 (pending) CLASS 2 UL94V-0 rated > 300,000 hrs ~ 50g PPM-Series – PPM10-E-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 Selection Guide Single Output Po Order # (W w er ) O lta t Vo u p t u V ge ( dc) Cu pu t O ut rren t d Loa F u ll ie Effic (m A ( ncy ) %) SINGLE OUTPUT PPM10-E-3R3ELF PPM10-E-05ELF PPM10-E-09ELF PPM10-E-12ELF PPM10-E-15ELF PPM10-E-24ELF 6.6 10 10 10 10 10 3.3 5 9 12 15 24 2000 2000 1100 900 700 450 70 74 76 76 78 80 If you need other specifications, please enquire. Package / Pinning / Derating 2 Bottom View 4 1 3 All dimensions are typical in millimeters (inches). - Pin diameter: 1.0 +/-0.10 (0.04 +/-0.004) - Pin pitch tolerance: +/-0.35 (+/-0.014) - Case tolerance +/-0.5 (+/-0.02) Specification may change without notice. 45.72 (1.80) 2" x 1" – PLASTIC CASE 53.50 (2.10) 6.00 (0.24) 19.00 (0.75) PEAK Modelcode Datecode # 1 2 3 4 PIN CONNECTIONS SINGLE AC (N) AC (L) + Vout - Vout PPM-Series – PPM10-E-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 App Notes: Measure Typical Applications PPM-Series FIGURE 1 FIGURE 2 External Typical Value Model C1 C2 PPM10-E-3.3ELF 220µF/10V 0.1µF/50V PPM10-E-05ELF 220µF/10V 0.1µF/50V PPM10-E-09ELF 120µF/25V 0.1µF/50V PPM10-E-12ELF 120µF/25V 0.1µF/50V PPM10-E-15ELF 120µF/25V 0.1µF/50V PPM10-E-24ELF 68µF/35V 0.1µF/50V TVS P6KE6.8A P6KE6.8A P6KE12A P6KE20A P6KE20A P6KE30A Note 1.Output filtering capacitors C1 is electrolytic capacitors. It is recommended to use high frequency and low impedance electrolytic capacitors. For capacitance and current of capacitor, please refer to manufacture’s datasheet. Voltage derating of capacitor should be 80% or above. C2 is ceramic capacitor - it is used to filter high frequency noise. TVS is a recommended component to protect post-circuits (if converter fails). 2. MOV is required for PPM10-E-xxELF models. Model 471KD05 is used to protect the device under surge. 3. It is recommended to connect FUSE (2A/250V slow blow). External input NTC model is recommended to use (5D-9). 4. If common requirement to EMC performance, refer to figure 1, if higher requirement to EMC performance, refer to figure 2. C3,C4:Y capacitor, recommended parameter 2200pF/400V; C5:X capacitor, recommended parameter 0.1uF/275V; NF: common model choke, recommended inductance is about 10mH-30mH. PPM-Series – PPM10-E-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3