PPM01-S-xxELF PPM-SERIES Rev.12-2014 1 Watt Univ. 85-305VAC (120-430VDC) Single Output Over Voltage Protection (out) 3 kV AC I/O Isolation Low Ripple and Noise High Efficiency Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PPM-Series is a compact size power converter provided by Peak. The features of this series are: wide input voltage, DC and AC all in one, high efficiency, high reliability, low loss, safety isolation etc. They are widely used in industrial, office and civil equipments. EMC and safety standards meet international standards IEC61000, UL60950 and IEC60950, and Multi-certificate is in processing. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Input Voltage Range Input Frequency Input (Inrush) Current External Input Fuse (recommended) 85 – 305 VAC or 120 – 430 VDC universal 47 – 63 Hz 115 VAC 230 VAC 30 mA (5A, typ.) 17mA (11A, typ.) 1A / 300V slow blow Output Specifications Voltage Accuracy Line Regulation (at full load) Load variation (10-100%) Ripple and Noise (20Mhz bandwidth) Short Circuit Protection ±5%, typ (±6% @3.3 Vout) ±2% ±5% ≤ 100mV pk-pk Continuous, auto recovery Common Specifications Temperature range Power derating Storage Humidity (non condensing) Switching Frequency I/O Isolation Voltage EMI / RFI conducted EMC compliance ESD RS EFT Surge CS PFM -25°C to +70 °C 3.3% / °C, min -40°C to +85 °C 95%, max. 100kHz 3000VAC / 1min. EN55022, Class B IEC/EN 61000-4-2 Contact±8KV/Air±8KV perf. Criteria B IEC/EN 61000-4-3 10V/m perf. Criteria A IEC/EN 61000-4-4 ±2KV perf. Criteria B IEC/EN 61000-4-5 ±1KV/±2KV perf. Criteria B IEC/EN 61000-4-6 10Vr.m.s perf. Criteria A IEC/EN 61000-4-8 10A/m perf. Criteria A Voltage dips, short and interruptions immunity IEC/EN 610004-11 0%-70% perf. Criteria B Safety Standards IEC60950, EN60950, UL60950 Safety Class CLASS 2 Case Material UL94V-0 rated Reliability Calculated MTBF (MIL-HDBK-217F) > 300,000 hrs Weight ~ 20g PPM-Series – PPM01-S-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 Selection Guide Single Output Order # ad ( ) mA x .) (ma F µ ) nt ad ge urre r Lo o lta y (% W) o c C V t ( i n t t r c e u u e a p p ci Pow Out Out Cap Effi Lo Full c) (Vd SINGLE OUTPUT PPM01-S-3R3ELF PPM01-S-05ELF PPM01-S-09ELF PPM01-S-12ELF PPM01-S-15ELF PPM01-S-24ELF 1 1 1 1 1 1 3.3 5 9 12 15 24 300 200 111 83 67 42 4000 4000 2200 2200 1000 680 63 68 72 73 74 75 If you need other specifications, please enquire. # 1 2 3 4 0.6 (0.024) 22.20 (0.874) 15.24 (0.60) Package / Pinning / Derating PIN CONNECTIONS SINGLE AC (N) AC (L) - Vout + Vout PPM-Series – PPM01-S-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 App Notes: Parallel Line Measure Typical Application EMC Recommended Circuit EXTERNAL CAPACITORS TYPICAL VALUE(Unit: µF) Model C1 C2 TVS 220 1µF/50V SMBJ7.0A PPM01-S-3R3ELF 1µF/50V SMBJ7.0A 220 PPM01-S-05ELF 1µF/50V SMBJ12A 120 PPM01-S-09ELF 1µF/50V SMBJ20A 120 PPM01-S-12ELF 1µF/50V SMBJ20A 120 PPM01-S-15ELF 1µF/50V SMBJ30A 68 PPM01-S-24ELF Note: 1. C1 is ceramic capacitor, it is used to filter high frequency noise. C2 is electrolytic capacitor, It is recommended to use high frequency and low impedance electrolytic capacitors. For capacitance and current of capacitor please refer to manufacture’s datasheet. Voltage derating of capacitor should be 80% or above. TVS is a recommended component to protect post-circuits (if converter fails). 2. For standard EMC requirement, please refer to figure 1. If higher EMC requirement, please refer to figure 3, recommended parameters are shown in the table below. Recommend Parameter For Higher EMC Standard Circuit Components Recommend Parameter MOV S14K350 CY3 2.2nF/400V CY4 2.2nF/400V CX 0.1µF/305VAC LCM 10 mH NTC 5D-9 FUSE 1A/300V, slow blow, it must be connected to FUSE PPM-Series – PPM01-S-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3