PPM03-S-xxELF

PPM03-S-xxELF
PPM-SERIES
Rev.05-2011
3 Watt
Univ. 85-264VAC (110-370VDC)
Single Output
Over Voltage Protection (out)
3 kV AC I/O Isolation
Low Ripple and Noise
High Efficiency
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
The PPM-Series are high efficiency green power moduls with various
packaging provided by Peak. The features of this series are: wide input
voltage, DC and AC all in one, high efficiency, high reliability, low loss,
safety isolation etc. They are widely used in industrial, office and civil
equipments. EMC and safety standards meet international standards
IEC61000 UL60950 and IEC60950, and Multi-certificate is in processing.
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Input Voltage Range
Input Frequency
Input (Inrush) Current
85 – 264 VAC or 110 – 370 VDC universal
47 – 440 Hz
110 VAC
230 VAC
PPM03 models 65 mA (10A), typ.
30mA (20A), typ.
External Input Fuse (recommended)
0.5A / 250V slow blow
Output Specifications
Voltage Accuracy
±2%, typ (±3% @3.3 Vout)
Input variation
±0.5%
Load variation (10-100%)
±1%
Ripple and Noise (20Mhz bandwidth)
≤ 60mV pk-pk
Short Circuit Protection
Continuous, auto recovery
Over output voltage protection
Chip lock up
Common Specifications
Temperature range
-25°C to +70 °C
Power derating
2% / °C
Case temperature
+95°C (max)
Storage
-40°C to +105 °C
Hold up Time
50mS, typ. (230VAC)
Humidity (non condensing)
95%, max.
Temperature Coefficient
0.02%/°C (main output)
Switching Frequency
100kHz
I/O Isolation Voltage
3000VAC / 1min.
Leakage current
None
EMI / RFI conducted
EN55022, level A
EMC compliance
ESD IEC/EN 61000-4-2 level 4 8KV/15KV
RF IEC/EN 61000-4-3
EFT / bursts IEC/EN 61000-4-4 level 3
Surge IEC/EN 61000-4-5 level 3 1KV/2KV
Safety Standarts
IEC60950, EN60950, UL60950
Safety Approvals
EN60950, UL60950
Safety Class
CLASS 2
Case Material
UL94V-0 rated
Reliability Calculated MTBF (MIL-HDBK-217F) > 300,000 hrs
Weight
~ 40g
PPM-Series – PPM03-S-xxELF – Single Output - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/3
Selection Guide
Single Output
Order #
Po
(W
w er
)
O
lta
t Vo
u
p
t
u
V
ge (
dc)
Cu
pu t
O ut
rren
t
d
Loa
F u ll
ie
Effic
(m A
(
ncy
)
%)
SINGLE OUTPUT
PPM03-S-3R3ELF
PPM03-S-05ELF
PPM03-S-09ELF
PPM03-S-12ELF
PPM03-S-15ELF
PPM03-S-24ELF
2.3
3
3
3
3
3
3.3
5
9
12
15
24
700
600
330
250
200
125
63
72
74
76
76
78
If you need other specifications, please enquire.
PIN CONNECTIONS
SINGLE
AC (L)
AC (N)
N.C.
- Vout
+Vout
+Vin (DC)
- Vin (DC)
100
Load(%)
#
1
3
13
14
16
22
23
0.8
(0.03)
23.00
(0.91)
17.78
(0.70)
Package / Pinning / Derating
80
60
40
20
-25 -10 0
55
Temperature(°C)
PPM-Series – PPM03-S-xxELF – Single Output - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/3
70
App Notes:
*FUSE
*NTC
L
L
C3
MOV
+
C1
+V0
C2
TVS
+
22
RL
26
-V0
N
N
*FUSE *NTC
L
L
C7
C6
C3
NF
MOV
+
+V0
C1 C2 TVS
+
22
RL
26
C8
-V0
N
N
PPM03 EMC Application Figure
EXTERNAL CAPACITORS TYPICAL VALUE(Unit: µF)
Model
C1
C2
C3
TVS
150
0.1
4.7/400V
P4KE6.8A
PPM03-S-3R3ELF
150
0.1
4.7/400V
P4KE6.8A
PPM03-S-05ELF
120
0.1
4.7/400V
P4KE12A
PPM03-S-09ELF
120
0.1
4.7/400V
P4KE20A
PPM03-S-12ELF
120
0.1
4.7/400V
P4KE20A
PPM03-S-15ELF
68
0.1
4.7/400V
P4KE30A
PPM03-S-24ELF
Note:
1. Output filtering capacitors C1, C3 is electrolytic capacitors, It is recommended to use high frequency and low impedance
electrolytic capacitors. For capacitance and current of capacitor please refer to manufacture’s datasheet. Voltage derating
of capacitor should be 80% or above. C2 is ceramic capacitor, it is used to filter high frequency noise. TVS is a
recommended component to protect post-circuits (if converter fails).
2. MOV is required to PPM03 models to protect the device under surge.
3. It is recommended to connect FUSE
4. If EMC performance is required, recommended to add “EMC filter” at the input end (see figures)
C6: X capacitor, recommended parameter 0.1µF/275V;
C7,C8: Y capacitor, recommended parameter 2200pF/400V;
NF: common model choke, recommended inductance is about 10mH-30mH.
5. PPM03 models: Terminals 22 and 26 are internal rectification and filtering terminals. To protect the models further, it is
recommended to connect an electrolytic capacitor C3 (it is recommended to be 4.7µF/400V). If operation voltage of the
module is between 160~264VAC, C3 can be removed.
PPM-Series – PPM03-S-xxELF – Single Output - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/3