PPM05-E-xxELF PPM-SERIES Rev.02-2015 5 Watt Univ. 85-305VAC (110-430VDC) Single Output Over Current/Voltage Protect 4 kV AC I/O Isolation Low Ripple and Noise High Efficiency Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PPM-Series are high efficiency green power moduls with various packaging provided by Peak. The features of this series are: wide input voltage, DC and AC all in one, high efficiency, high reliability, low loss, safety isolation etc. They are widely used in industrial, office and civil equipments.. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Input Voltage Range Input Frequency Input (Inrush) Current External Input Fuse (recommended) Output Specifications Voltage Accuracy Input variation Load variation (10-100%) Ripple and Noise (20Mhz bandwidth) Short Circuit Protection Over output voltage protection Over current Protection Common Specifications Temperature range (Storage) Power derating Hold up Time Humidity (non condensing) Temperature Drift Coefficient Switching Frequency I/O Isolation Voltage Safety Standards Safety Class Case Material Reliability Calculated MTBF (MIL-HDBK-217F) Weight EMV Specifications 85 – 305 VAC or 110 – 430 VDC 47 – 440 Hz 110 VAC 230 VAC 120mA, max. (10A, typ.) 70mA, max. (20A, typ) 1A / 300V slow fusing ±2%, typ (±3% at 3.3 Vout) ±0.5%, typ ±1% , typ 50mV pk-pk, typ Continuous, self-recovery TVS clamp ≥ 110% Iout self-recovery -25°C~ +70 °C case max: 95°C (-25°C~ +105 °C) 2% / °C 80mS, typ. (230VAC) 95%, max. ±0.02%/°C 100kHz, typ 4000VAC / 1min. IEC60601, EN60601 CLASS II UL94V-0 rated > 300,000 hrs ~ 35g See AppNote PPM-Series – PPM05-E-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 Selection Guide Single Output ) mA F) * (µ d a e Lo t ) re n citiv tage r l ) a u o y (% p W c C V a ( n t t r C e u u e . p p ci Pow Out Out Max Effi Lo Full c) (Vd Order # ad ( SINGLE OUTPUT PPM05-E-3R3ELF PPM05-E-05ELF PPM05-E-09ELF PPM05-E-12ELF PPM05-E-15ELF PPM05-E-24ELF 4.2 5 5 5 5 5.5 3.3 5 9 12 15 24 1250 1000 550 420 333 230 4000 74 4000 78 1000 78 820 80 820 82 680 83 * without external circuit If you need other specifications, please enquire. Package / Pinning / Derating 2 Bottom View 4 1 3 All dimensions are typical in millimeters (inches). - Pin diameter: 0.5 +/-0.05 (0.02 +/-0.002) - Pin pitch tolerance: +/-0.35 (+/-0.014) - Case tolerance +/-0.5 (+/-0.02) Specification may change without notice. 45.72 (1.80) 2" x 1" – PLASTIC CASE 50.80 (2.00) 6.00 (0.24) 15.16 (0.60) PEAK Modelcode Datecode # 1 2 3 4 PIN CONNECTIONS SINGLE AC (N) AC (L) + Vout - Vout PPM-Series – PPM05-E-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 App Notes: EMV Specifications (without ext. circuit) EMI Conducted Disturbance Radiated Emission EMS Electrostatic Discharge Radiation Immunity EFT Surge Immunity CISPR22/EN55022, CLASS B CISPR22/EN55022, CLASS B IEC/EN61000-4-2 ±6KV/8KV Perf. Criteria B IEC/EN61000-4-3 10V/m perf. Criteria A IEC/EN61000-4-4 ±2KV perf. Criteria B IEC/EN61000-4-5 ±1KV perf. Criteria B Conducted Disturbance immunity Immunity for Power frequency magnetic field Immunities of voltage dip, drop and short interruption IEC/EN61000-4-6 10 Vr.m.s perf. Criteria A IEC/EN61000-4-8 10A/m perf. Criteria A IEC/EN61000-4-11 0%-70% perf. Criteria B Typical Applications PPM-Series Model PPM05-E-3R3ELF PPM05-E-05ELF PPM05-E-09ELF PPM05-E-12ELF PPM05-E-15ELF PPM05-E-24ELF C1 (µF) C2 (µF) 1 220 1 220 1 100 1 100 1 100 1 47 Note: Output filtering capacitor C2 is electrolytic capacitor, it is recommended to apply electrolytic capacitor with high frequency and low resistance. Capacitance withstand voltage derating should be 80% or above. C1 is ceramic capacitor, which is used to filter high-frequency noise. External input NTC is recommended to use 13D-5. Applications for higher EMC Component MOV2 CY1, CY2 CX L1 LCM PPM-Series – PPM05-E-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3 Recommended S14K350 1nF / 400VAC 0.1µF / 310VAC 4.7µH / 2.0 A 2.2mH