PPMxx-SIP-xxELF PPM-SIP-SERIES Rev.08-2011 1.65 - 3 Watt Univ. 100-400VDC / 85-264VAC* Single Output Over Temperature Protection Short Circuit Protection 2 kV AC I/O Isolation High Efficiency / Density Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PPM-SIP-Series are high efficiency green power modules with miniature packaging provided by Peak. The features of this series are: wide input voltage, DC and AC all in one, high efficiency, high reliability, low loss, safety isolation etc. They are widely used in industrial, office and civil equipments, as well as applications where no special requirement for EMC performance. It is recommended to add EMI suppression circuit or take measure to shield when there is strict requirement for EMC performance. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Input Voltage Range Input Current External Input Fuse (recommended) 100 – 400 VDC or 85 – 264 VAC* universal 40mA, typ. 0.5A / 250V * Attention: For AC-Input a capacitor between PIN 7 and PIN 10 is needed!! (See page 3) Output Specifications Voltage Accuracy Input variation Load variation (10-100%) Ripple and Noise (20Mhz bandwidth) 3.3 / 5 / 9 VDC models 12 VDC models 15 VDC models 24VDC models ±2% ±0.5%, typ. ±1%, typ. ≤ 100mV pk-pk ≤ 120mV pk-pk ≤ 150mV pk-pk ≤ 240mV pk-pk Short Circuit Protection Over Temperature Protection Continuous, auto recovery 150°C, max. Common Specifications Temperature range Power derating Case temperature Storage Humidity (non condensing) Temperature Coefficient Switching Frequency I/O Isolation Voltage Leakage current Case Material Reliability Calculated MTBF (MIL-HDBK-217F) -40°C to +85 °C 1.33% / °C (above 55°C) +90°C, max. -40°C to +105 °C 85%, max. 0.02%/°C 100kHz, typ. 2000VAC / 1min. None UL94V-0 rated > 300,000 hrs PPM-SIP-Series – PPMxx-SIP-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 Selection Guide mA) ad ( o ) L c l l d t Fu e (V %) rren ltag ) u o W V C cy ( ( n t t r e u u i e p p Pow Out O ut Effic Order # SINGLE OUTPUT PPM1.65-SIP-3R3ELF 1.65 3.3 PPM2.5-SIP-05ELF 2.5 5 PPM3-SIP-09ELF 3 9 PPM3-SIP-12ELF 3 12 PPM3-SIP-15ELF 3 15 PPM3-SIP-24ELF 3 24 If you need other specifications, please enquire. 500 500 330 250 200 125 70 70 75 78 78 78 Package / Pinning / Derating 10.50 (0.413) max. Printed Face Backside 1 3 7 10 > 3.00 (0.12) max. 25.50 (1.004) max. 35.00 (1.38) 12 0.40 (0.016) 0.84 (0.033) 3.53 (0.14) max. 22.86 (0.90) 12.70 (0.50) 5.08 (0.20) All dimensions are typical in millimeters (inches). - Pin section tolerance: +/-0.10 (+/-0.004) - Case tolerance +/-0.5 (+/-0.02) SIP Specification may change without notice. – AC/DC Load(%) 100 PIN CONNECTIONS # SINGLE 1 +Vout 3 - Vout 7 - Vin 10 CAP 12 +Vin 80 60 40 -40 -20 Temperature( C ) PPM-SIP-Series – PPMxx-SIP-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 55 85 App Notes: Structure Figure 12 +Vin(L) Rectificate 7 -Vin(N) C1 External Capacitor 1 Rectifier filter circuit DC/DC Con vertor 3 +Vo -Vo Voltage sampling + 10 Con trl Circuit Feedback loop Anear Measure Connect Oscillograph Probe Copper sheet Fuse C1 + C2 10 C3 Load 7 25.4mm 25.4mm Typical Application DC Input AC Input F use 12 +Vi n +Vo C 2 1 F use C 3 TvS R L EM C F ilter 12 L NF MOV + C5 + 3 10 -Vo C1 N C 3 TvS R L + C4 -Vo 7 1 MOV C6 -Vi n +Vo C 2 7 3 L S03 DC in pu t typica l ap p licatio n in pu t typica l ap p licatio n Attention: For AC-Input a capacitor (10uF/400V) between PINL7S03 andAC PIN 10 is needed!! External Capacitor Typical Value Output Voltage 3.3V 5V 9V 12V 15V 24V C1 C2 C3 TVS FUSE P4KE6.8A 150µF/25V 10µF/400V 0.1µF/50V (Ceramic Capacitor) 100µF/35V 0.5A/250V P4KE12A P4KE20A P4KE33A Note: 1. Filtering capacitors C1, C2 are electrolytic capacitors, C1 is used for AC input, when input voltage is below 100VAC, the value of C1 is 22µF/400V. C2 is recommended to use high frequency and low impedance electrolytic capacitors. For capacitance and current of capacitor please refer to manufacture’s datasheet. Voltage derating of capacitor should be 80% or above. C3 is ceramic capacitor. It is used to filter high frequency noise. TVS is a recommended component to protect postcircuits (if converter fails). 2. MOV: Voltage dependent resistor, model 471KD05. It is used to protect converter in lightning strike and surge. 3. If EMC performance is required, it’s recommended to add “EMC filter” at the input side. C4: X capacitor: 0.1µF/275V C5,C6: Y capacitor: 220pF/2000V NF: Common-mode choke, recommended parameter: 10mH-30mH PPM-SIP-Series – PPMxx-SIP-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3