F E D C B A NOTES: n1,8 (2x) 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. METALSHELLS: COPPER ALLOY; min. 315µin TIN over 40-80µin NICKEL 3. INSULATORS: PBT GF UL 94 V-0; GREEN 4. HIGH POWER CONTACTS 10A: COPPER ALLOY PLATING MATING AREA: GOLD FLASH over NICKEL D PLATING TERMINATION SIDE: GOLD FLASH over NICKEL D SOLDER CUP ACCEPTS CABLE AWG 16-20 MALE CONTACT ON POS. A1; FEMALE CONTACT ON POS. A2 6. COLLARS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL 7. HEXLOCKING SCREWS: STAINLESS STEEL 8. FRAME: ZINC DIE CAST; NICKEL PLATED SEALING COMPOUND 3,6 +- 0,25 0 9. O-RING: SILICON; BLUE (5:1) 14,25 +- 0,1 0,4 5. THREADED INSERTS: COPPER ALLOY; min 200µin TIN over 80µin NICKEL 10. SEALING COMPOUND: PUR; BLUE 11. RECOMMENDED PANEL CUT-OUT ON SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max.40Ncm (3.5 in.LB) 13. CONNECTOR IS PART MARKED: 602W2CSXX61B30X CONEC ABC 5,73 +- 0,17 0,08 AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. 39,4 +- 0,3 0 C C 0,02 8 +- 0,23 0,12 25 +- 0,13 21,1 +- 0,3 0 16,41 +- 0,05 0,2 10° B B O-RING 602W2CSXX61B30X CONEC ABC 4-40 UNC SEE NOTE 8 9,4 4,6 SEE NOTE 13 SW 4,8 Directive 2002/95/EC RoHS compliant F E DO NOT ALTER CAD DRAWING BY HAND A THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 4-40 UNC scale: material: tolerance 2:1 (5:1) SEE NOTES dim. in mm date A title: name drawn 06.01.12 Henneboel D-SUB COMBINATION FEMALE appd. 06.01.12 Fischer 2W2CS SOLDER CUP with threaded insert and hexlocking screw dwg no: DIN- norm d-old Original rev. description D date part no: name C A3 sh: 1 15K1A989 R a B 602W2CSXX61B30X A F E D C B A Solder Instruction D D 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350°C, 100 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 5 seconds longer. Do not heat contact more than 6 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. C C RECOMMENDED PANEL CUT OUT 20,5 `0,1 i 0,26 A B 11,4 `0,1 B Ø3,1 `0,05 (2x) B R3 ,4 ` 10°`1° F E DO NOT ALTER CAD DRAWING BY HAND THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 25 `0,1 A i 0,26 B 0, 13 A scale: material: tolerance 3:1 SEE SHEET 1 dim. in mm date A title: name drawn 06.01.12 Henneboel PANEL CUT-OUT appd. 06.01.12 Fischer D-SUB FEMALE 2W2CS SOLDER CUP with threaded insert and hexlocking screw dwg no: DIN- norm d-old Original rev. description D date part no: name C A3 sh: 2 15K1A989 R a B SEE SHEET 1 A