F E D C B A n1,04 (15x) NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. METALSHELLS: COPPER ALLOY; min. 315µin TIN over 40-80µin NICKEL SEALING COMPOUND 3. INSULATORS: PBT GF UL 94 V-0, BLACK oPLEASE ADD C for 30µin HARD GOLD over min. 50µin NICKEL D oPLEASE ADD B for 20µin HARD GOLD over min. 50µin NICKEL oPLEASE ADD A for GOLD FLASH over NICKEL (PREFERRED TYPE) D 6,3 `0,3 8,8 `0,3 4. SIGNAL CONTACTS: COPPER ALLOY; PLATING (SEE PART NO.) SOLDER CUP ACCEPTS CABLE AWG 22 5. THREADED INSERTS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL 6. COLLARS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL 7. FRAME: ZINC DIE CAST; NICKEL PLATED 8. HEXLOCKING SCREW: STAINLESS STEEL 12. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max.40Ncm (3.5 in.LB) 13. CONNECTOR IS PART MARKED: 6HDD15SoM99B20X CONEC ABC (see note 4) 5,73 +- 0,17 0,08 11. RECOMMENDED PANEL CUT-OUT SEE SHEET 2 3,6 +- 0,25 0 9. O-RING: SILICON; BLUE 10. SEALING COMPOUND: PUR; BLUE 39,4 +- 0,3 0 8 +- 0,02 0,23 0,13 25 +- 0,12 16,41 +- 0,05 0,2 C C 21,1 +- 0,3 0 AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. 10° SEE NOTE 7 6HDD15S oM99B20X CONEC ABC O-RING B B M3 9,4 4,6 SEE NOTE 13 M3 Directive 2002/95/EC RoHS compliant F E DO NOT ALTER CAD DRAWING BY HAND A THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH SW 4,75 scale: material: tolerance 2:1 (5:1) SEE NOTES dim. in mm date A title: name drawn 05.07.12 Henneboel D-SUB HD FEMALE appd. 05.07.12 Fischer 15pos. SOLDER CUP with threaded insert and hexlocking screw dwg no: DIN- norm d-old Original rev. description D date part no: name C A3 15K1A1069 R a sh: 1/2 6HDD15SoM99B20X (see note 4) B A F E D C B A D D Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350°C, 50 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. C C 11,4 `0,1 RECOMMENDED PANEL CUT-OUT 20,5 `0,1 i 0,26 A B B n3,1 `0,05 (2x) B 10°`1° R3 , A F E DO NOT ALTER CAD DRAWING BY HAND THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 25 `0,1 i 0,26 B 4` 0, 1 3 A scale: material: tolerance 3:1 see sheet 1 dim. in mm date drawn 05.07.12 Henneboel appd. 05.07.12 Fischer A title: name PANEL CUT-OUT D-SUB COMBINATION FEMALE Solder cup; with hexlocking screw dwg no: norm d-old 15K1A1069 R a Original rev. description D date part no: name C B SEE SHEET1 A DINA3 sh: 2/2