F E D C B A NOTES: 1. FOR WAVESOLDERING ( SOLDER BATH TEMPERATURE 240°C FOR 5 SEC. 10,5 `0,3 AND SOLDER PREHEAT 120°C FOR 120 SEC. ) 2. METALSHELLS: COPPER ALLOY; min. 315µin TIN over 40-80µin NICKEL (4,15) 3. INSULATOR: PBT GF UL 94 V-0, GREEN PLATING, MATING AREA: GOLD FLASH over NICKEL D 2,25 Ø1,9 (3x) 4. HIGH POWER CONTACTS 15A: COPPER ALLOY PLATING, TERMINATION SIDE: 160-240µin TIN over 80µin NICKEL 5. METAL BRACKETS: ZINC DIE CAST; 300µin COPPER/ 40-120µin NICKEL/ 120-200µin NICKEL (5:1) 6,35 `0,3 D SEALING COMPOUND 6. THREADED INSERTS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL 8. FRAME: ZINC DIE CAST; NICKEL PLATED 9. O-RING: SILICON; BLUE 10. RUBBER GASKET: TPE BLACK 11. SEALING COMPOUND: PUR; BLUE max. 2 5,93 +- 0,32 0,28 7. HEXLOCKING SCREWS: STAINLESS STEEL 12. P.C.B. HOLE DRILLINGS + RECOMMENDED PANEL CUT-OUT ON SHEET 2 13. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. 5,7 +- 0,12 0,18 3,6 +- 0,25 0 max. 40Ncm (3.5 in.LB) 14. CONNECTOR IS PART MARKED: 6003W3PXX59S20X CONEC ABC 47,7 +- 0,3 0 8,26 +- 0,22 0,03 33,3 +- 0,15 0,1 C RUBBER-GASKET PLACED ON TOP SURFACE OF MALE INSULATOR 25,17 +- 0,2 0,05 21,1 +- 0,3 0 A1 C METAL BRACKET b 6003W3PXX59S20X CONEC ABC O-RING 4-40 UNC SEE NOTE 8 4,6 9,4 SEE NOTE 14 9,9 `0,2 B 5,65 `0,2 B n3,18 (3x) 10° SW 4,8 b F RoHS compliant E DO NOT ALTER CAD DRAWING BY HAND A THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 4-40 UNC scale: material: tolerance 2:1 (5:1) SEE NOTES dim. in mm date drawn 10.07.2012 Henneboel D-SUB COMBINATION MALE appd. 10.07.2012 Koch 3W3P SOLDER PIN ANGLED threaded insert, metal bracket and hexlocking screw dwg no: DIN- norm d-old 2xb Ä5536 a Original 12.02.15 A title: name M.H. rev. description D date part no: name C A3 sh: 1 15K1A1073 R B 6003W3PXX59S20X A F E D C B A P.C.B. HOLE DRILLINGS ( P.C.B. TOP SIDE ) D D 33,32 +- 0,15 0,1 6,86 `0,1 n3,1 `0,1 (2x) A1 P.C.B. EDGE 3,63 `0,1 9,25 3,35 6,86 `0,1 FRONTPANEL n2,3 `0,1 (3x) C C RECOMMENDED PANEL CUT-OUT 28,8 `0,1 i 0,26 A B B n3,1 `0,05 (2x) 11,4 `0,1 B 10° `1° F E DO NOT ALTER CAD DRAWING BY HAND 33,3 `0,1 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH A R3 i 0,26 B ,4 ` 0, 1 3 A scale: material: tolerance dim. in mm date SEE SHEET 1 drawn 10.07.2012 Henneboel P.C.B. HOLE DRILLINGS appd. 10.07.2012 Koch PANEL CUT-OUT D-SUB Combi. Male 3W3P Solder Pin angled dwg no: DIN- d-old Original rev. description date part no: name C A3 sh: 2 15K1A1073 R D A title: name norm a 3:1 B SEE SHEET 1 A