100W GaN SSPA With L-Band Block Upconverter X- Band Model B4XO-N Global Applications With CPI-built RF brick inside and plenty of thermal margin, this SSPA is rock-solid and highly efficient, utilizing state-of-the-art GaN technology. Perfect for Satcom on the Move, Micro Flyaway Systems, VSATs, and antennamount applications. Meets Electromagnetic Compatibility Directive 2004/108/EC to satisfy worldwide requirements. High LInearity Excellent AM/PM, phase noise and spectral regrowth performance. Simple to Operate User-friendly microprocessor-controlled logic with Ethernet computer interface (serial interface optional). Also contains digitally controlled attenuator. Redundant systems available. Worldwide Support Backed by over three decades of satellite communications experience, and CPI’s worldwide 24-hour customer support network that includes sixteen regional factory service centers. The Basics Provides 100 watts of output power over the 7.9 to 8.4 GHz frequency band. 811 Hansen Way P.O. Box 51625, Palo Alto, CA 94303 tel: +1 (650) 846-3803 fax: +1 (650) 424-1744 e-mail: [email protected] www.cpii.com/satcom 1 0 0 W G a N P o w e r S S PA w i t h B U C CPI-Built RF Brick Inside X-Band 100 W GaN power X-band SSPA with Block Upconverter environmentally sealed in a compact package for outdoor operation X-B a n d SPECIFICATIONS, 100 W GaN X-Band Outdoor Solid State SSPA with BUC (Model B4XO-N) Monitor and Control Electrical OPTIONS: • 1 RU Remote Control Panel • 1:1 Redundant Switching • Ethernet Interface • AC Option (requires external converter module - contact CPI for details) Frequency 7.9 to 8.4 GHz L-Band Input 950 to 1450 MHz Output Power Saturated (Psat) Linear (Plin) 100 W (50 dBm) 50 W (47 dBm) Small Signal Gain 70 dB min. External Reference Frequency Level 10 MHz 0 dBm ±5 dB Internal Reference Gain Stability Over temp., constant drive Over 24 hours, fixed temp. ±1.5 dB over oper. temp. range ±0.25 dB ±0.04 dB/MHz max. Small Signal Gain Variation Across any 40 MHz band Across the full band ±0.3 dB pk-pk max. ±1.25 dB Gain Adjustment Range 20 dB, 0.1 dB steps Input VSWR 1.5:1 max. (50 ohms) Output VSWR 1.3:1 max. 2.0:1 1.5:1 Residual AM, max. -80 dBc > 100 kHz from carrier Phase Noise, max. 10 Hz 100 Hz 1 kHz 10 kHz 100 KHz 1 MHz -33 dBc/Hz -63 dBc/Hz -73 dBc/Hz -83 dBc/Hz -93 dBc/Hz -93 dBc/Hz AM/PM Conversion 2.0°/dB max. at Plin Harmonic Output -60 dBc max. at rated linear power Spurious Response at Plin -60 dBc max. in band Noise Density <-90 dBW/4 kHz, receive band <-70 dBW/4 kHz, passband Intermodulation Distortion -25 dBc with two equal carriers at total output power of 50 W Spectral Regrowth -30 dBc at 1 SR, OQPSK Group Delay (in any 80 MHz band) 0.03 ns/MHz linear max. 0.003 ns/MHz2 parabolic max. 1.0 ns pk-pk ripple max. Primary Power 28 VDC ±20% (48 VDC ±20% optional) Power Consumption 370 W typical AC Option 100 - 240 VAC ±10%, 47-63 Hz Power Factor Correction .99 (when operating with AC option) Certificate Number: 30515 For more detailed information, please refer to the corresponding CPI Technical Description. Note: Specifications may change without notice as a result of additional data or product refinement. MKT 312B, ISSUE 10 12/11 PDF Remote Status Transmit/Standby/Inhibit Status Control Point (local/CIF/Internet) Environmental Ambient Temperature -40°C to +55°C operating in direct sunlight; -40°C to +60°C operating out of direct sunlight; -50°C to +85°C non-operating Relative Humidity 100% condensing Altitude 12,000 ft. with standard adiabatic derating of 2°C/1000 ft., operating; 50,000 ft., non-operating Cooling Integral forced air Shock and Vibration 20 g peak, 11 msec, 1/2 sine; 2.1 grms, 5 to 500 Hz. Mechanical RF Output Connection Load VSWR Continuous operation Full spec compliance Transmit ON/OFF Fault Reset Attenuator Setting Computer/Network Interface RS-232C and 422/485 (Ethernet optional) Standby option ±1 ppm stability Gain Slope Please contact CPI before using this information for system design. Remote Control CPR-112G waveguide flange grooved with UNC-2B 10-32 threaded holes L-Band Input Connection Type N female M&C Connection Serial and basic Ethernet interface Dimensions width height length Weight 5.2" (133 mm) 4.9" (125 mm) 11.5" (293 mm) (optional AC input requires additional external converter module - contact CPI for details) 14 lbs (7.5 kg) typ. (w/DC input)